|
| 1 | Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hardbroken granitestone jelly for foundation including dewatering if foundnecessary and laid in layers of not more than 15cmthick and compacted,etc., complete complying withstandard specification. |
| 2 | Supplying and filling in foundation andbasement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification. |
| 3 | Providing and laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications. |
| 4 | Plain Cement Concrete 1:1.5:3 (one cement, one and half fine aggregates and three coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification |
| 5 | Plastering with cement mortar 1:5 (One Cement, Five Sand) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications. |
| 6 | Painting two coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete. |
| 7 | Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excludingcost of such specials cutting threading of pipes andfixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holesin roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete. - 20MM dia,G.I pipe |
| 8 | 25MM dia,G.I pipe |
| 9 | Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements. - 25mm dia G.M.Gate Valve |
| 10 | Plastering in Cement Mortar 1:3 Mix (one Cement, Three sand) 20mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications as per TNDSS No.56 & 57 |
| 11 | Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessaryscaffolding charges. - 32MM dia,PVC pipe |
| 12 | 25mm dia.PVC pipe |
| 13 | Suppling and fixing in position15mm.diameter brass screw down tap(heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary. |
| 14 | Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C.floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications. - 110mm dia PVC Elbow |
| 15 | 110mm dia PVC Tee |
| 16 | Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitaryfittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications. - 110mm dia PVC 6KSC Pipe |
| 17 | Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification. |
| 18 | Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for PVC Open light point / Fan point (For Electronic regulator). SD 22 |
| 19 | Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54 |
| 20 | Supply and fixing of single box type 4\"36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87 |
| 21 | Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class \"B\" GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234 |
| 22 | Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5mSD.75 |
| 23 | Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TCwire with painting of suitable colour SD 68 |
| 24 | Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41 |
| 25 | Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2\" x 1 1/2\" x 1/4\" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1\" x 1/4\" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 129 |
| 26 | Supply, fixing and commissioning of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 120 X 65 X 50, channel 75 x 40, L angle 40 x 60 & shaft 60mm dia. Capacity of 1Mt to 1.5Mt / Hour with single shaft cutter, stell grade blade, 10Hp motor, size 600mm X 800mm X 600mm, chute - yes (Feeding & discharge) with mannual feeding, Electrical - 10HP starter only without cable, total machine height is 2000mm and width 1200mm feeding conveyor - 1 No (Mannual) etc, complete. inclusive GST-18% |
| 27 | Manufacture, Supply, Installation and commissioningof output conveyors to convey the manure. Length- 5 meter, Width of belt- 1.0 meter, 3 ply, 12 mm thick rubberised. The conveyor is trough angle with a pitch of 500 mm for the placement of the rollers and 2500 mm for the return rollers. The trough angle should not be more than 20 deg and the conveyor belt is electrically operated. The conveyor has side skirts to avoid material spillage and heavy duty steel support fabricated structure for its placement. The conveyor will be supplied by with a 5.0 HP, 3 Phase, 1440 RPM motor or Higher. Equipment will be supported with all necessary fabricated steel structures attachments, angles, accessories and complete electrical wiring till the central panel board and starter to operate the conveyors to a speed of half to one meter per second and conveying capacity of 3 TPH.It is driven by electric motor and gear box. Motor make: Kirloskar /ABB /Crompton Greaves or Equivalent, Gear Boxes: PBL / Shanthi Gears/ Premium or Equivalent, Electrical Items: Schneider/ Legrand/ ABB/ L&T/ Polycab/ Crompton or Equivalent, Conveyor Belt: Hindustan/ Plycon/ Dunlop or Equivalent Structural Steels shall be IS226 grade. MS plates shall be IS.2062 grade B. inclusive GST-18% |
| 28 | Supply and Fixing of incinerator (sanitary napkin buring machine) of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication \"PUF\" Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete. inclusive GST-18% |
