Jharkhand State Building Construction Corporation Limited has published Tender For Redevelopment Work Of Sub-Divisional Hospital Building At Chandil In Saraikela-Kharsawan District.. Submission Date for this Tender is 31-05-2023. Building Work Tenders in saraikela Jharkhand. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 19-May-2023 | Corrigendum | Date | 31-05-2023 |
| 2 | 26-May-2023 | Corrigendum-2 | Other | 31-05-2023 |
| Sl. No. | Item Description |
| 1 | Earth Work inexcavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I |
| 2 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 3 | Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume). |
| 4 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including" cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume). |
| 5 | Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l. |
| 6 | Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 7 | Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). |
| 8 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6(1Cement:3coarsesand(zone-III):6gradedstoneaggregate40mm nominal size) |
| 10 | Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size) |
| 11 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. |
| 12 | Plant mix method (Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401) |
| 13 | With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 |
| 14 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all omplete as per the direction of Engineer-in-charge. |
| 15 | Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 16 | Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme onthe boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge. |
| 17 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 18 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 19 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 20 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying butexcludingthecostofcentering,shuttering,finishingandreinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). |
| 21 | All works upto plinth level |
| 22 | All works above plinth level upto floor V level |
| 23 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns,etc. for mass concrete |
| 24 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 25 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) |
| 27 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 28 | Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts |
| 29 | Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases |
| 30 | Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMTFe 500 (only vailid for TATA (TISCON), SAIL,JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 31 | Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMTFe 500 (only vailid for TATA (TISCON), SAIL,JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 32 | Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMTFe 500 (only vailid for TATA (TISCON), SAIL,JSPL, Electro steel Limited Bokaro and Vizal steel(RINL)) |
| 33 | Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I. |
| 34 | Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinthwith approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I. |
| 35 | Providing Designation 100AB/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 36 | Providing designation 112mm thick reinforced designation 100A brick work with flyash lime brick (FLAG)in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 37 | Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary |
| 38 | Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock abJSORbers as specified and applying a coat of approved steel primer after pre- treatment of the surface as directed by Engineer-in-charge: Profile B |
| 39 | Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I. |
| 40 | Supplying, fitting and fixing 32mm , thick good quality well dressed and well seasoned wood fully paneled shutters ( frame made of sal wood and panel of sisum wood) in doors and window with 20mm, thick panels with one side plain and other side chamfered with aluminium fittings such as hinges, sliding door, bolts, tower bolts, handled or rings, hooks and eyes, cleats, sand blocks as per schedule, taxes and royalty all complete as per building specification and direction of E/I. |
| 41 | Supplying, fitting and fixing 38mm , thick good quality well dressed and well seasoned Teak wood 1/3rd paneled and 2/3 glazed shutter in doors and window with 25mm thick panels with one side plain and other side chamfered with aluminium fittings such as hinges, sliding doors boltes tower bolts handles or rings, hooks and eyes, cleats, sand blocks as per schedule and 3mm thick plain glass panes fitted with teak wood beads and taxes all complete as per building specification and direction of E/I. |
| 42 | Supplying fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both side decorative veneered with black board core bended with high quality phenol formal clehydes synihetic resin of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pebuilding specrfication and direction of E/l. |
| 43 | Supplying fitting and fixing 35mmthick solid core type decorative double leaf flush door sltutter with both side decorative veneered with black board core bended with high quality phenol formal clehydes synihetic resin of standard make with Aluminium fittings :such as hinges, tower bolts, hendle, cleats and sand blocks and laxes all conrplete as pebuilding specrfication and direction of E/l. |
| 44 | Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l. |
| 45 | Providing and fixing LeadLined Door including freme & hinges, jamb, lock jamb, bead and if required hinges 2.5 mm thick with mortar guards,lock,closer,all complete as per derection by Engineer-in-charge: LEAD LINEDDOOR |
| 46 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 47 | Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). |
| 48 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accesJSORies and screws etc. complete. |
| 49 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 50 | Providing and fixing chromium plated brass night latch of approved quality including necessary screws etc. complete. |
| 51 | Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete.Size 50 mm |
| 52 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :300 x 10 mm |
| 53 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :125 mm |
| 54 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.Twin rubber stopper |
| 55 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 56 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge.(b) Extruded section profile size 42x50 mm |
| 57 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of "H" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. "U" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 58 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws.30 mm thick shutters.Kiln seasoned selected class of sheesham wood |
| 59 | Providing and fixing L/T-iron frames for doors, windows and ventilators of mild steel Angle/Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) |
| 60 | Fixing standard steel glazed doors, windows and ventilators in walls, including fixing of float glass panes with glazing clips and special metalsash putty of approved make, or metal beading with screws, (only steel windows, glass panes cut to size and glazing clips or metal beading with screws, shall be supplied by department free of cost. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 61 | Supplying,frtting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved design and drawing, properly fabrlcated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/1 |
| 62 | Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 63 | Structural steel work single section, Fixed with or without connection plate including cutting, hoising,fixing in position and applying a priming coat of approved steel primer all complete. |
| 64 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works. |
| 65 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.MS tube |
| 66 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accesJSORies & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accesJSORies such as nuts, bolts, fasteners etc.). |
| 67 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes |
| 68 | Providing and laying 25mm. thick kotah stone slab flooring of approved size, texture and colour over 19 mm thick base of lime morter (1:l:1) ( Lime putty : surkhi: coarse sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size. |
| 69 | Providing and laying 25mm. thick kotah stone riser of steps, skirting and pillers of approved size, texture and colour over 12 mm thick cementmorter (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size. |
| 70 | Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 71 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 72 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry@ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 73 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer )with water abJSORption less than 0.08% and conforming to IS:15622 / ISO 13006 of approved make , in all colurs and shades, laid on 20mm thick cement mortor 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cementand matching pigments etc., complete Size of Tile 600mm x 600mm |
| 74 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Size of Tile 600 x 600 mm |
| 75 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 76 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade,Area of slab over 0.50 sqm |
| 77 | Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.Granite work |
| 78 | Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. |
| 79 | Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platfometre. Vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubing and polishing of cut edges etc. complete. |
| 80 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Ordinary cement without any pigment |
| 81 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. |
| 82 | In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand |
| 83 | In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) |
| 84 | Providing & Fixing flexible Conductive PVC sheet flooring of Armstrong/ Forbo/ Polyflor having a total thickness of 2mm and weight of 3kg/m².Colors and pattern detail shall be dispersed throughout the thickness of the wear layer. It shall conform to Group P of Wear Resistance as per EN 649, Flammability of class Bfl-s1 as per EN 13501-1, Slip resistance as per DIN 51130group of R9 , having REACH Registration No, 1907/2006 contains no substance mentioned in SVHC list. Impact sound reduction of 3 dB as per ISO 140-8, Residual indentation of0.05 mmas per EN 433, Color fastness rating =6 as per ISO 105-B02, Vertical resistance(R1) less than 1 x 106- 1x 108? as per EN 1081, and surface resistance less than 1 x 106- 1x 108 Electrical insulation to ground greater than 50 k? as per VDE 0100, Static electrical charge of =2.0kV as per EN 1815, Thermal resistance of 0.04m²K/W as per EN 12667, Thermal conductivity of 0.25 W/mK. Equivalent to Armstrong PASTELL. Installation:It is important to ensure the sub floor on which the sheet is being laid is smooth, flat & hard & free from moisture, grease, etc. In case of uneven sub floor the same should be leveled by self leveling compound. |
| 85 | The moisture level present in the subfloor should be less than 8% before installation of the floor. The sheet should be laid using adhesive recommended by company.Each row of tiles/strip of floor covering must be linked crosswise with a continuous copper strip. Individual rows/strips must be at least 3 m² in size and linked to the rest of the area with a copper tape. In rooms of up to 40 m², connection points for equipotential bonding should be provided in at least one point in the room. |
| 86 | Providing and laying of 2 - 3 mm average thick layer of cementations smoothening compoundof UZIN NC 149 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer over and including a priming compound of UZIN PE 360 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer and installation team on concrete surface to provide a smooth & homogenous surfacefor laying of vinyl sheet flooring complete to the entire satisfaction of Engineer-in-charge. |
| 87 | Providing 50mm thick 2nd class patent stone flooring (1:2:4) with 20mm, to 6mm size graded stone chips finished with flooring coat of neat cement in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royality with all complete as per building specification and direction of E/I. |
| 88 | Providing & fixing Rockfone Stonewool Acotsical Ceiling PACIFIC High NRC (0.80), Fire Rating A1 (EN 13501-1), RH 100% (No visible deflection in high humidity), Superior Class Light Reflection, Sag Resistant 12mm thick Ceiling Tiles of size 600x600 A-Edge(Square) with AntiBacterial Properties & M1 Class Emission Certification made up with Natural Stone (Bassalt Rock) a complete Green Product & perfect suitable for any kind of False Ceiling application in builiding & costruction. The Visible side is a smooth white painted fleece, the Rear side: back fleece with complete facctory finish Painted edges. |
| 89 | Supply and installation of Wallflex PUR Vinyl Sheet wall covering manufactured by Armstrong World Industries, Inc, 1.5m wide, having a nominal total thickness of 1mm. The nominal thickness of the wear layer would be 1mm. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC, Plasticizers, Urethane, color pigments and filler calendared to form a sheet. Colors shall be dispersed throughout the thickness of the wear layer. Wallflex shall conform to Group M of Wear Resistance as per EN 660-2, Fire resistance of group 2 as per AS/NZS3837, Residual indentation of =0.10mm as per EN433, curling after exposure to moisture =8mm as per EN434, Seam strength of mean=240N/50mm as per EN684.Make of : Armstrong/Polyflor/Forbo |
| 90 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase |
| 91 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 92 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni). |
| 93 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonrywith polymer mixed slurry |
| 94 | WATERPRROFING FOR OLD AND NEW ROOF SLAB : Providing and laying waterproofing treatment on Roof Slab by applying two component factory designed ,ready to use ,acrylic modified flexible material applied with brush ,roller, or spray for waterproofing coating caoting as per manufacturer specification and following steps surface praparation : Providing nd cleaning of concree surfase to remove the dust oil,grease including removal of existing loose paint/ coatingand cement laitance by cleanning with compressed air and water jet including all materials ,laobour tools complete .Pondig test to be done after plugging all outlets and to checked from soffit to identify seepage ,leakage . on identification ofseepage ,cement grouting to be done with non shrink expanding admixture of SIKA INDIA PVT Ltd /MYK Schomburg /Dr.Fixit/fosroc or equivalent . providing and Repairing of all corners and joints such as those between the parapet wall and the roof slab etc shall be campererd with 150 mmx150 mm fillet of mortor (Cement :sand-1:4) Admixed with acrylic polymer of Sika /Fosroc/MYK/Dr.Fixit damaged concreting base slab,dead cracks if any with an acrylic polymer modified repair mortor including coat of Bonding agent of the same with cement slurry including all material,labour,tools comlplete. |
| 95 | b) Apply fisrt coat two component acrylic modified ,ready use ,flexible cementituous material on surface saturated dry roof and inside wall of paraphet wall upto 600 mm by brush or roller .After 1st coat of application ,45 GSM of fibre cloth to lay when fibre glass cloth when the first layer is still in green .1st coat to be applied @1.5kg/sqmt/coat. for the purpose of measurement entiretreated surface will be maesured. c)2nd coat -To apply the 2nd coat of two component acrylic modified ready to use ,flexible cementituous material at right angle to the first coat over the glass fibre laid surface 2nd coatshould be applied at @.7 kg /sqmtr /coat. for the purpose of measurement entiretreated surface will be maesured.After three days of drying 2nd coat the rain water outlets to be plugged and ponding test to be done for 48 hrs to identify the seepage ,leakage from the sofit and if found necessary rectification to be done as per satisfaction of E/C. |
| 96 | The waterproofing coating to protected from damage before screed over it.Waterproofing brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr.Fixit Pidifin 2K/MYK Aquafin TG Product Prformance--Chemical Base part A Acrylic Polymer ,Part B ,Specially graded cementitious powder Density -1.6 Kg/l(mixed density) at 27 C .Tensile strength -2N/MM2 After 28 days (with fibre cloth )According to ASTM D2370),Pull out bond strength -2N/mm2(concrete failure )According to ISO 4624 Slant shear bond strength -4N/MM2(According to FIP 5.15)Elongation at break -35% without fibre cloth and 20% with fibre cloth (According to ASTM D2370) d) Protection of treated surface with PCC -The treated surface should be covered with 25mm/50MM PCC of M-20 Grade (1:1.5:3) with proper slope (1:20) towards the rain outlets in alternate pannel of 2mtrx2mtr keeping gap of between the pannel joint .Integral waterproofing admixture confirming to IS 2645 @ 100ML Per Bag of cement to be added inscreed concrete (Paid seperately for this item) all corners to be champered with 150mmx150mm fillet .The Rain water oulets shall be just levelled with the screed to ensure smooth discharge of water -The pherperal gaps between PVC pipes oulet and concrete surface to be packed properly with moisture insensitive epoxy putty of Sika India Pvt Ltd/MYK Schomburg/Dr.Fixit/Fosroc. |
| 97 | For purpose of measurement the entire traeted surfaceto be measured. e) Goove of PCC -Surfcae should be filledwith polysulphide sealent (paid Seperately) Brand -Sika India Pvt Ltd/MYK Schomburg /Dr.Fixit/Fosroc.Warranty 10 years Covering treated surface with PCC: Providing 50 MM thick cement concrete M20(1;1.5;3) Maintaining slope in alternate pannel 2mtx2mt pannels with approved quality stone chips 20mmto 6mm size graded and sand of F.M.2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral waterproofing and placing position,striking,curing taxes ,loyality all complete as per specification and direction of E/I,Pannels that has been left should be casted next day ,There should be 6mm gap between the Pannels. Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent |
| 98 | Providing and mixing integral waterproofing compound in concrete or plaster as per manufacturer specification and as per direction of Eng in chargeBrand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent |
| 99 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I. |
| 100 | Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 101 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 102 | Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I. |
| 103 | Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 104 | Providing two coats of oil bond Distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone of fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification direction of E/I |
| 105 | Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/l. |
| 106 | Providing two coat of synthetic enamel paint of approved shade and make over new woodan suface taxes all complete as per building specification direction of E/I |
| 107 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 108 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 109 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 110 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. |
| 111 | Finishing walls with Acrylic Smooth exterior paint of required shade Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 112 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately):For fixed portion.Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 113 | For shutter of doors, window & ventilators including providing and fixing hinges / privots and making provision for fixing of fitting wherever required including the cost of EPDM rubber / neoprene gasket required ( fitting shall be paid saparatly )Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 114 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness |
| 115 | Providing Flexstone Brick tiles , Made In India, for cladding along the walls, made with recycled raw materials and cement used as a binder, with Density more than 1800kg/m3, high compressive strength around 50 Mpa and abrasion resistant, exterior grade applied with polymer based adhesive with good adhesion strength and fast curing. Product to be green and sustainable, LEED certified, weather & algae fungus resistant, breathable, insulated, no VOC, fire rated and have high melting point and almost no discoloration. Stone weighing approx 4 to 5 Kgs/sqft to be applied with the polymer modified adhesive applied as a uniform scratch coat first and individual pieces over it. The protective transparent water based breathable PU sealer coat to be done overall with the help of a brush in the final stage for a maintenance free cladding altogether. Products to be maintenance free and the company to provide 12 years of warranty against manufacturing defect. Fixing and cutting of the stones to be done as per the drawings, specifications and instructions of the Architect or Engineer incharge. |
| 116 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar |
| 117 | BRICKS ( 8KM ) |
| 118 | CHIPS( 22KM ) |
| 119 | METAL( 22KM ) |
| 120 | SAND ( 10KM ) |
| 121 | Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. |
| 122 | (a) From 0.00 M to 50.00 M below G.L. |
| 123 | (b) From 51.0 M to125.00 M |
| 124 | (c) From126.0 M to150.00 M |
| 125 | Supplying, assembling, lowering and fixing in vertical position in borewell,unplasticizedPVCmediumwellcasing(CM)pipeof required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia |
| 126 | Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge |
| 127 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia |
| 128 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp |
| 129 | Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP |
| 130 | Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I. |
| 131 | Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etcall complete job as per direction of E/I. |
| 132 | Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I. |
| 133 | SANITARY INSTALLATIONS |
| 134 | Supplying , fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I "p" trap 15 liters C.I.pull and let go flushing cistren of names or other I.S.S. equivalent make , complete with all fitting , C.I.or C.C. brackets 32mm alkathene/P.V.C telescopic flush , pipe about 2 M longwith one brass coupling and clamps GI ,chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less thane 50grms. 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coats of red oxide primer etc. all complete as per specification and direction of E/I. |
| 135 | (A) 580 mm. long |
| 136 | (c) With 10 lit. low level PVC Cistem |
| 137 | Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I.brass waste, 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I. |
| 138 | Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I. (i) Kitchen sink 600 mm x 450 mm x 250 mm |
| 139 | Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete. Flexible Pipe, 32mm Dia. |
| 140 | Providing and fixing white vitreous china laboratory sink with CI brackets , C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets , cutting and making good the wall wherever required : Size 600x450x200 mm |
| 141 | Providing and fixing toilet paper holder C.P. brass |
| 142 | Flexible (coil shaped} PVC waste pipe for sink and wash basin 304 32mm dia with length not less than 700 mm i/c PVC waste fittings |
| 143 | Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350gms.) with extra socket all complete as per specification and direction of E/I. |
| 144 | Providing and fixing lead connection pipe with heavy quality brass coupling 2 nos. at both ends etc all complete as per specification and direction of Engineer-in-charge. 15 mm dia and 45 cm long, |
| 145 | Providing and fixing N.P/C.P. brass /P.V.C. porcelain shower rose of 15mm inlet etc. all complete as per specification and direction of Engineer - in -Charge.(c) 150mm dia P.V.C shower |
| 146 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 147 | (a) Glass shelf with C P brass rail, (i) 600×125 mm glass shelf complete |
| 148 | 600mm x 450mm size |
| 149 | 450 mm x 300 mm size |
| 150 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. ofquality and make as approved by Engineer - in charge. |
| 151 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms. |
| 152 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms. |
| 153 | Providing & fixingPTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms |
| 154 | (ii)15 mm dia brass bib cock wt. not less than 400 gms |
| 155 | Providingandfixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 156 | Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. 15 mm nominal bore |
| 157 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length, 15 mm nominal bore |
| 158 | Special type of C.P. Bath room fittings for V.I.P. Buildings (JAL, Jaquar, Marc or equivatent make) (ISi Marked) Toilet Paper Holder |
| 159 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and Granite Stone of approved shade |
| 160 | Providing & fixing rain water `Khurras" size 450x450 mm required depth with lead flashing around the pipe with one piece lead sheet of 3 mm thick set on a layer of cold bitumen. Including Heavy duty CI/MS grating as per drawing complete as required. |
| 161 | Providing and fixing C.P concealed four way diverter with thermostatic mixer with shut off valve and diverter, including cutting and making good the walls, wherever required. (Make:- Jaquar -Four way diverterKUB-35421, Thermostatic mixer 35671 or Equilent) |
| 162 | Providing and fixing CP brass single lever low flowwall mounted Sink mixer with 15 mm CP brass single lever swivel spout with waste complete with flow rate 2.5 litre per minute at 3 bar including cutting and making good the walls where required. ( MAKE-1: JAQUAR, MODEL NO. SINK MIXER : FLR-CHR-5163GD ROCA MODEL NO : G1935A1 |
| 163 | Providing, Installing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm complete as required. Capacity 25 litres size 448X448X345mm ( MAKE-1: JAQUAR, MODEL NO. GEYSER : ELENA OREQUIVALENT.) |
| 164 | INTERNAL DRAINAGE INSTALLATIONS |
| 165 | Providing and fixingcast iron trap of self cleansing design withcast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. |
| 166 | 100 mm inlet and 100 mm outlet |
| 167 | Sand Cast Iron S & S as per IS:3989 |
| 168 | Providing and fixing soil, waste, vent and rain water pipes |
| 169 | Centrifugally cast (spun) iron S&S pipe |
| 170 | 100mm dia cast (spun) iron S&S pipe |
| 171 | 75 mm dia cast (spun) iron S&S pipe |
| 172 | Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. |
| 173 | For 100 mm dia. Pipe |
| 174 | For 75 mm dia. Pipe |
| 175 | Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. |
| 176 | 100 mm dia |
| 177 | Centrifugally cast (spun) iron pipe S&S |
| 178 | 75 mm dia |
| 179 | Centrifugally cast (spun) iron pipe S&S |
| 180 | Providing and fixing plain bend of required degree. |
| 181 | 100 mm dia |
| 182 | Sand cast iron S&S as per IS : 3989 |
| 183 | 75 mm dia |
| 184 | Sand cast iron S&S as per IS : 3989 |
| 185 | Providing and fixing heel rest sanitary bend, |
| 186 | 100 mm dia. |
| 187 | Centrifugally cast (spun) iron pipe S&S |
| 188 | 75 mm dia. |
| 189 | Centrifugally cast (spun) iron pipe S&S |
| 190 | Providing and fixing terminal guard: |
| 191 | 100 mm |
| 192 | Sand cast iron S&S as per IS - 3989 |
| 193 | 75 mm |
| 194 | Sand cast iron S&S as per IS - 3989 |
| 195 | Providing and fixing collar. |
| 196 | 100 mm |
| 197 | Sand cast iron S&S as per IS - 3989 |
| 198 | 75 mm |
| 199 | Sand cast iron S&S as per IS - 3989 |
| 200 | Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : |
| 201 | 100 mm dia cast (spun) iron S&S pipe |
| 202 | 75 mm dia cast (spun) iron S&S pipe |
| 203 | Providing, Fixing, testingand commissioningof UPVC pipe SWR type "B" conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, "Y", offset, cleaning pipe door, clamps and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type "B". The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint. |
| 204 | 75 mm diameter pipe |
| 205 | 110 mm diameter pipe |
| 206 | Providing, Fixing and laying cement concrete 1:2:4mix (1 cement :2 coarse sand :4 graded stone aggregate, 20 mm down gauge) 75 mm in bed and all around UPVC waste pipes under floor, including shuttering and necessary reinforcement etc. complete as required for: - 100 mm dia |
| 207 | Providing, Fixing, testing and commissioning of UPVC "P" trap/floor trap/urinal trap of self cleansing design with or without horn conforming to IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20 mm nominal size) cutting and making good the walls & floors.110 mm (OD) x 110 mm (OD) |
| 208 | Providing, fixing & testing uPVC pipes, conforming to IS 4985 class 3 (6 kg/cm2) including injection moulded fittings, jointing with solvent cement, cutting and making good the floors and walls and jointingto trap/waste pipe, complete of outer dia. (Indirect waste) 40mm diameter pipe |
| 209 | Providing, Fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect. 110 mm OD x 63 mm OD |
| 210 | Providing, fixing and testing of uPVC SWR inlet fittings with two or three saddle inlets of 40, 50 or 63 mm size, fabricated from 110 mm outer dia uPVC pipes and fixed to uPVC traps with solvent cement joint complete in all respect. |
| 211 | Providing and fixing PTMT grating of approved quality, colour and make 125 mm nominal dia with 25 mm waste hole |
| 212 | Providibng and fixing straight type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector.(supreme/Prince) |
| 213 | WATER SUPPLY INSTALLATIONS |
| 214 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 215 | Providing and laying cement concrete 1:2:4mix (1 cement :2 coarse sand :4 graded stone aggregate, 20 mm down gauge) 75 mm thick in bed and all around UPVCpipes under floor, including shuttering and centering for: - 110 mm dia |
| 216 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams. |
| 217 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Terrace andRiser. |
| 218 | PN - 16 Pipe, 20mm OD (SDR-7.4) |
| 219 | PN - 16 Pipe, 25mm OD (SDR-7.4) |
| 220 | PN - 16 Pipe, 32mm OD (SDR-7.4) |
| 221 | PN - 16 Pipe, 40mm OD (SDR-7.4) |
| 222 | PN - 10 Pipe, 50mm OD (SDR-11) |
| 223 | PN - 10 Pipe, 63 mm OD (SDR-11) |
| 224 | Providing and fixing PPR Unions |
| 225 | PPR Union 20 mm |
| 226 | PPR Union 25 mm |
| 227 | PPR Union 32 mm |
| 228 | PPR Union 40 mm |
| 229 | PPR Union 50 mm |
| 230 | PPR Union 63 mm |
| 231 | Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l |
| 232 | (a) 15 mm dia wt not less than 300 gms |
| 233 | (a) 20mm dia wt not less than 400 gms |
| 234 | (a) 25 mm dia wt not less than 500 gms |
| 235 | (a) 32 mm dia wt not less than 700 gms |
| 236 | Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall |
| 237 | 15 mm nominal outer dia pipes |
| 238 | 20 mm nominal outer dia pipes |
| 239 | 25 mm nominal outer dia pipes |
| 240 | 32 mm nominal outer dia pipes |
| 241 | 40 mm nominal outer dia pipes |
| 242 | 50 mm nominal outer dia pipes |
| 243 | Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direction of engineer incharge Concealed work including cutting chases and making good the wall etc. |
| 244 | 15 mm nominal outer dia pipes |
| 245 | 20 mm nominal outer dia pipes |
| 246 | 25 mm nominal outer dia pipes |
| 247 | 32 mm nominal outer dia pipes |
| 248 | Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design. |
| 249 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia |
| 250 | Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge |
| 251 | Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge |
| 252 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge |
| 253 | DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area |
| 254 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 255 | Butterfly Valves :: - Providing, fixing, testing & commissioning of wafer type cast iron butterfly valves conforming to BS 5155 & IS 13095 tested to 15 Kg/Sq.cm pressure for maximum working pressure of 10 bar (PN 10) including all fitting and accessories (Drain, water meter for OH Tank/Riser). |
| 256 | 50 mm dia |
| 257 | 65 mm dia |
| 258 | WATER SUPPLY EXTERNAL |
| 259 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. |
| 260 | 25mm nominalnominal bore |
| 261 | 32mm nominalnominal bore |
| 262 | 40mm nominalnominal bore |
| 263 | 50mm nominalnominal bore |
| 264 | 65 mm nominal nominal bore |
| 265 | Providing & Fixing of Garden hydrant outlet consisting 1 No. 25mm dia. Ball valve,( Brass)for connecting rubber hose, pipes & fittings. |
| 266 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) |
| 267 | 25 mm dia, nominal bore |
| 268 | 32 mm dia, nominal bore |
| 269 | 40 mm dia, nominal bore |
| 270 | 50mm nominal bore |
| 271 | 65mm nominal bore |
| 272 | Constructing masonry Chamber 60x45x50 cm,inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. |
| 273 | With F.P.S. bricks |
| 274 | Providing and fixing GI pipescomplete (IS:1239 Heavy Class) with GI fittingsand clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete.(WTP Room Abow the UGT.) |
| 275 | 50 mm dia, nominal bore |
| 276 | 65 mm dia, nominal bore |
| 277 | 80 mm dia, nominal bore |
| 278 | Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality |
| 279 | 50 mm dia, nominal bore |
| 280 | 65 mm dia, nominal bore |
| 281 | 80 mm dia, nominal bore |
| 282 | Providing and fixingG.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete. |
| 283 | 32 mm dia, nominal bore |
| 284 | 40 mm dia, nominal bore |
| 285 | 50 mm dia, nominal bore |
| 286 | 65 mm dia, nominal bore |
| 287 | Providing & fixing in position precast RCC manhole cover and frame of reqd. shape and approved quality. EHD - 35 Circular shape560 internal dia. |
| 288 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : |
| 289 | With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 290 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 50 mm dia |
| 291 | Providing and fixing cast iron wafer type butterfly valves (PN-10) complete with 2 nos. matching flanges (Table-E),bolts, nuts, 3.0 mm thick insertion neoprene gasket. |
| 292 | 40mm dia |
| 293 | 50mm dia |
| 294 | 65mm dia |
| 295 | 80mm dia |
| 296 | Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. 65mm dia. |
| 297 | Providing & fixing CI `Y" Strainer (screwed/ flanged) with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers complete as required. 65mm nominal bore |
| 298 | Providing and fixing M.S fabricated hot dipped galvanized coating puddle flange comprising of 600 mm dia long M.S class "B" pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: Underground / Overhead Tanks.) |
| 299 | 25mm dia pipe, 600mm long with size of 250x250x6 mm MS plate |
| 300 | 32mm dia pipe, 600mm long with size of 250x250x6 mm MS plate |
| 301 | 40mm dia pipe, 600mm long with size of 300x300x6 mm MS plate |
| 302 | 50mm dia pipe, 600mm long with size of 350x350x6 mm MS plate |
| 303 | 65mm dia pipe, 600mm long with size of 350x350x6 mm MS plate |
| 304 | 100mm dia pipe, 600mm long with size of 400x400x6 mm MS plate |
| 305 | 150mm dia pipe, 600mm long with size of 450x450x6 mm MS plate |
| 306 | 200mm dia pipe, 600mm long with 6 mm MS plate of size 600mm dia |
| 307 | Providing, laying, Jointing, Testing and commissioning of uPVC pressure pipes of 10Kg/Sqcm pressure rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per standard design. |
| 308 | 25 OD mm. |
| 309 | 32 OD mm. |
| 310 | 40 OD mm |
| 311 | 50 OD mm |
| 312 | 63 OD mm |
| 313 | RO SYSTEM |
| 314 | Supply, installation, testing and commissioning built with Drinking Water R.O. unit with micron filtration pre-treatment unit, skid mounted R.O. module with pressure pump and pressure tank, drinking water cooler (High quality SS Tank for Storage 80 lts) , complete in all respects. ( Make & Model No. Eureka Forbes Pure Chill RO Storage Cooler cum Purifier or Equivalent) |
| 315 | EXTERNAL SEWERAGE & DRAINAGE INSTALLATIONS UPTO MAIN ROAD FIRST MANHOLE |
| 316 | Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/I. All kinds of soil (ii) For classification of soil item-B |
| 317 | Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. |
| 318 | 150 mm diameter |
| 319 | 200 mm diameter |
| 320 | 250 mm diameter |
| 321 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design. |
| 322 | 150 mm diameter |
| 323 | 200 mm diameter |
| 324 | 250 mm diameter |
| 325 | Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design.(COVER MIN. 4.5 KG & FRAME MIN.2.7 KG ) 150x100mm size P type With FPS bricks |
| 326 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.14.14.2-150 mm dia |
| 327 | Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. |
| 328 | 150 mm dia RCC pipe |
| 329 | 250 mm dia RCC pipe |
| 330 | 300 mm dia RCC pipe |
| 331 | 450mm dia RCC pipe |
| 332 | Providing and laying in position cement concrete of grade excluding the cost of centering and shuttering - all work up to plinth level 1:5:10 (1 cement : 5 coarse sand : 10 graded ston aggregate 40 mm nominal size) |
| 333 | Construction brick masonry manhole in cement mortar 1:4 (1cement : 4coarse sand) RCC top slab with 1:2:4 mix 9 with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. |
| 334 | Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5 |
| 335 | Extra for depth for manholesSize 90 x 80 cm with FPS bricks designation 7.5 |
| 336 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture"s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 ( 1cement : 3coarsesand :6 gradedstoneaggregate 20 mm nominal size) complete as per design. |
| 337 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 338 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter |
| 339 | PUMPS & ALLIED WORKS |
| 340 | Providing, installing, testing and commissining of variable speed (VSPS) hydropneumatic system mounted on a common base plate comprising of vertical centrifugal pumping set with S.S body, stainless steel impeller and mechanical seal, shaft directly coupled to a TEFC induction motor suitable for 400/440 volts, 3 phase, 50cycles AC supply with 150mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation,one No. microprocessor based controller,dedicatedvariable frequency drive for each pump, one No.remote sensors, pressure transducers, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, one No. 90 litre capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects including MS Zinc coated suction and delivery headers and isolation/ control valves( ball valves/butterfly valves/ Nan return valves/ vibration eliminators etc as required) , power box, equipped with fuses/ isolators/circuit breakers as required. |
| 341 | The entire Hydropneumatic system shall be factory fitted. |
| 342 | Hyd. System for Domestic Water Supply Pump |
| 343 | Flow rate : 2 lps each |
| 344 | Pumping Head-70 m |
| 345 | 1 Set = 2 Nos. pump (1 working+1 standby) |
| 346 | Approx H.P.- 3 HP or as per manufacturer recommendation. |
| 347 | Location - Abow UGT. |
| 348 | Flow rate : 1.5 lps each |
| 349 | Head: 70 Mts |
| 350 | Required for : Flushing water transfer pump |
| 351 | (1 working + 1 standby) |
| 352 | Location -Abow STP |
| 353 | Supplying, installing, testing and commissioning of SS vertical centrifugal pump. Each pump shall have TEFC 2900 RPM three phase electric motor. The pump shall have cast iron head, base plate SS Shaft / Impeller / Intermediate chamber along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Pump shall be provided with mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve (25 dia). The pump shall be suitable for auto/ manual operation. The installation shall be complete with all necessary ancillaries, starter panel / control panel & accessories including base plate complete as required. |
| 354 | Flow rate : 2 lps each |
| 355 | Head: 70 Mts |
| 356 | Required for : Filter feed pump |
| 357 | (1 working + 1 standby) |
| 358 | Location - Abow UGT. |
| 359 | Providing, fixing, testing & commissioning of vertical FRP filter with adequate dirt holding capacity. Fabricated from FRP sheet as per IS-2825 and manufacturer"s specifications complete with intitial charge filter media . The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (PVC 10 Kg) and multiport valve . it is designed on 1.50 m / sec velocity. |
| 360 | WATER TREATMENT PLANT (WTP) |
| 361 | Dual Media Filter For Domestic Water Supply |
| 362 | Capacity- 7200 LPH |
| 363 | Filtration rate- 16000LPH/Sqm. |
| 364 | Filter dia approx. - 750 MM |
| 365 | Working pressure: 3.0 Kg/sqcm. |
| 366 | Test pressure :4. 5 Kg/sq cm |
| 367 | Activated Carbon Filter For Domestic Water Supply |
| 368 | Capacity- 2500 LPH |
| 369 | Filtration rate- 16000LPH/Sqm. |
| 370 | Filter dia approx. - 750 MM |
| 371 | Working pressure: 3.0 Kg/sqcm. |
| 372 | Test pressure :4. 5 Kg/sq cm |
| 373 | Treated water Pumps- Domestic water OHT Filling |
| 374 | Capacity : 150 LPM |
| 375 | Head : 70 m |
| 376 | App. HP : 3 HP |
| 377 | Motor RPM : 2900 |
| 378 | Each set consists of 2 pumps (1Working +1Standby). At any given time, only one pump need operate. Both the pumps must operate alternatively in service. |
| 379 | Providing & fixing butterfly valve (with motorized actuator) of rating PN 1.6, wafer type, in cast iron body with Ductile Iron disc, EPDM seal, SS single piece shaft, conforming to IS-13095 of the following sizes complete with cast iron hand level companion flanges, bolts, nuts, washers & inserted rubber gaskets, as required and as per enclosed specification,with single phase Electrical Actuator, of 15Nm- 400Nm Torque, made of aluminium alloy (resistant to heat, acid , alkali, corrosion), and weather proof heavy duty motor, with stabilized start speed to effectively avoid water hammering, with waterproofing seal (IP 67) for all housing seals, low noise level, built –in thermal protection complete as per specifications |
| 380 | 40 mm nominal bore |
| 381 | 50 mm nominal bore |
| 382 | Providing and fixing lever operated gun metal ball valve with SS-316 ball. |
| 383 | 40 mm nominal bore |
| 384 | 50 mm nominal bore |
| 385 | Supplying, fixing, testing and commissioning of Cast Iron butterfly valve of PN 1.0 rating with SS-316 seat, Shaft SS-316 duly ISI marked complete with SS bolts & nuts, washers, gaskets conforming to IS 13095 of following sizes as required and two matching flanges as per table "E" etc. |
| 386 | 65 mm nominal bore |
| 387 | 80 mm nominal bore |
| 388 | 100 mm nominal bore |
| 389 | Providing, Installation ,testing and commission of Cast Iron Dual plate (SS-316 Plates) Non Return valve as per technical specification complete with rubber gaskets, SSbolts & nuts, washers etc. as required and two matching flanges as per table "E" etc. |
| 390 | 40 mm nominal bore |
| 391 | 50 mm nominal bore |
| 392 | 65 mm nominal bore |
| 393 | 80 mm nominal bore |
| 394 | Providing and fixing of Cast Iron flanged Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 316, sheet with 3 mm dia. holes with stainless steel flange with rubber gaskets, SSbolts & nuts, washers etc. complete as required. |
| 395 | 50 mm nominal bore |
| 396 | 65 mm nominal bore |
| 397 | Providing and fixing of Pressure gauge (dial size minimum 6”) weather proof (IP-55) with a scale range from 0 to 10 Kg / cm² including stop cock. |
| 398 | Providing and fixing G.I. suction & delivery headers / pipes for water supply pumps (IS:1239 heavy class) with G.I. Fittings (bends, tees, reducers, plugs, union, flange & blank flanges etc.) and clamps and jointing with Teflon tape or hold tite including chase cutting and making good the walls, floors etc. wherever required. Paintingwith two or more coats of synthetic enamel paint of approved quality and shade over a coat of approved primer coat as directed including surface preparation (Shade as per pipe colour code) |
| 399 | 40 mm nominal bore |
| 400 | 50 mm nominal bore |
| 401 | 65 mm nominal bore |
| 402 | 80 mm nominal bore |
| 403 | Providing and fixing double flanged flexicion rubber expansion joint with unit control of standard length of a as per manufacturer specs tested to a pressure of 15 kg/sqcm including rubber gasket, flanges, nuts ,bolts and washers complete as required. 40 mm nominal bore |
| 404 | Design, manufacture, supplying,fixing in position, testing and commissioning of the following front operated cubicle type, front access 2mm thick mild steel sheet, free standing, dust proof, switchboard with IP42 protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs, bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system and suitable for a fault level of 25 MVA symmetricalat 415 volts. |
| 405 | All switchboards shall have provision for entry of cables from the top or bottom as required. |
| 406 | All live accessible parts shall be shrouded and all equipment shall be finger touch proof.The busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used.Padlocking facility shall be provided on all outgoing feeders doors and switch handles shall be lockable in OFF position. |
| 407 | Electric Panel For Water Supply Pumps at Water Supply Pump Room |
| 408 | INCOMING |
| 409 | 1 No. 63 amps TPN MCCB with the following accessories: |
| 410 | 1 No. square flush mounting 0-500 volts scaled voltmeter with three way and OFF switch. |
| 411 | Three phase indicating lights. |
| 412 | Electrolytic high conductivity three phase and neutral tinned copper bus bar rated at 100 amps having a current density of 1 amp per Sqmm suitable to with stand symmetrical fault level of 25 MVA at 415 volts.The neutral bus bar is to be of 100% capacity. |
| 413 | OUTGOING UNITS |
| 414 | 6 25/40 Amp. TP + NL M.C.C.B. with rotary handle of breaking capacity 25KA |
| 415 | Two 63 Amp. TP + NL M.C.C.B. with rotary handle of breaking capacity 25KA |
| 416 | 2 Nos. fully automatic DOL starters with push buttons and ON/OFF indicating lights and overload relays for 1.5 to 7.5 HP pump . |
| 417 | 2 Nos. rotary selector switch for selecting mode of operation i.e. auto/manual/off. |
| 418 | 2 Nos.cyclic relayfor automatic duty changeover of pumps. |
| 419 | 2 No. single phase preventors. |
| 420 | 2 Nos. square flush mounting 0-30 amps scaled ammeters with three way and OFF selector switch. |
| 421 | Space for 3 Nos. Level Controllers. |
| 422 | Switchgear shall be suitable for theHPS of various motors. |
| 423 | 1 Nos. 63 Amp. TPN MCB Spare. |
| 424 | 2 Nos. 32/40 Amp. TPN MCB Spare. |
| 425 | The motor control panel shall be prewired with colour coded wires with identification labels complete in all respects as required. |
| 426 | Supplying, installing, testing and commissioning controllers with low voltage relays, stainless steel probes and PVC shroud wiring from tank top to probes of required. |
| 427 | Level Controller For Water Supply Pump: |
| 428 | To start pump when water level is low in Domestic Water U.G. tank and shut off pump when Domestic Water U.G. tankis full.Also to stop when water level is low in raw water underground tank. |
| 429 | SEWAGE TREATMENT PLANT 45 KLD |
| 430 | Design, Supplying, installing, testing & commissioning of Sewage Treatment Plant of 45 KLD (excluding excavation, back filling & disposal of surplus earth MS / Civil construction work) for the following duty: |
| 431 | Sewage treatment plant shall include the following items: |
| 432 | a. Screen chambers with SS Screen b. Equalization Tank c. Aerobic & Anoxic tank d. MBBR TANK e. Air Blowers f. MBBR Media g. Recirculation pumps, backpulse pump, permeate pump etc. h. Dewatering system j. Electrical Panel, Cabling (Power & Control), Earthing k. Tertiary Treatment l. Clear Water tank and Flushing Water tank. |
| 433 | pH - 6.0 – 8.5 |
| 434 | BOD5 : 250 - 350 mg/lit |
| 435 | Total Suspended Solids (TSS): 250 - 450 mg/lit |
| 436 | COD : 500 - 700 mg/lit |
| 437 | Oil / Grease: upto 50 mg/lit |
| 438 | Inflow time: 24 HRS |
| 439 | Peak factor: 3 |
| 440 | Temperature: Ambient |
| 441 | Desired Sewage QualityAfter Treatment |
| 442 | pH : 7 - 8 |
| 443 | BOD5 : < 10 mg/lit |
| 444 | Total Suspended Solids (TSS): < 10 mg/lit |
| 445 | COD : < 50 mg/lit |
| 446 | Oil / Grease: < 5 mg/lit |
| 447 | Colour : Colourless |
| 448 | Odor : unobjectionable |
| 449 | E.coli : Nil |
| 450 | NH4-N :< 5 mg/lit |
| 451 | N Total :< 10 mg/lit |
| 452 | PO4-P : 2 mg/lit |
| 453 | Note: |
| 454 | Vendor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, schematic diagram for the above said component and additional component if so required for the complete working of the STP for the full capacity. |
| 455 | INLET SEWAGE CHARACTERSTICS (ASSUMED) |
| 456 | EFFUENT TREATMENT PLANT 5KLD |
| 457 | Design, Supplying, installing, testing & commissioning of Effluent Treatment Plant of 5 KLD (excluding excavation, back filling & disposal of surplus earth and Civil construction work) for the following duty: |
| 458 | Effluent from OT Scrubs, blood bank, labs etc. Some solvent/ chemical waste originating typically from hospital complex shall also be discharged into the ETP. Design to take consideration of same. |
| 459 | INLET EFFLUENT CHARACTERSTICS |
| 460 | PH: 5.5 - 9.0 |
| 461 | BOD: 250 - 600 mg/l |
| 462 | S. Solids : 200 - 650 Mg/l |
| 463 | COD: 600 - 1200 mg/l |
| 464 | Oil & Grease: 50-140 mg/L |
| 465 | Effluent discharge standard after treatment |
| 466 | pH - 6.0 – 8.5 |
| 467 | BOD - Less than 150 Mg/L |
| 468 | S. Solids - Less than or equal to 100 Mg/L |
| 469 | COD - Less than or equal to 300 Mg/L |
| 470 | Oil & Grease -Less than 5 Mg/L |
| 471 | Screen Chamber |
| 472 | Equalization tank/sump |
| 473 | Primary Tube Settler |
| 474 | Dosing System |
| 475 | Sludge Holding Tank |
| 476 | UV System |
| 477 | Air Blowers, Pumps & equipment |
| 478 | Piping, valves etc |
| 479 | Clarified Water tank |
| 480 | Electrical Panel & Cabling |
| 481 | Note: |
| 482 | Contractor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, schematic diagram for the above said component and additional component if so required for the complete working of the STP for the full capacity. |
| 483 | Effluent treatment plant shall include the following items: |
| 484 | FIRE FIGHTING WORKS |
| 485 | Supplyingandfixingsingleheadedinternalhydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheelISI marked conformingtoIS5290(Type-A)withblank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal |
| 486 | Supplying andfixing first-aidHoseReelwithMS constructionspraypaintedinpostofficered, conformingtoIS884completewiththefollowingas required. 20mmnominalinternaldiawaterhosethermoplastic (Textile reinforced) type -2 as per IS: 12585 20mmnominalinternaldiagunmetalglobevalve& nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m |
| 487 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipewith63mmdiamaleandfemalecouplingsduly boundwithGIwire,rivetsetc.conformingtoIS636 (type-A) as required : Gun Metal |
| 488 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter sizenozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal |
| 489 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI markedcompletewithnuts,bolts,washers,gaskets conforming to IS 13095 of following sizes as required : 100 nominal bore |
| 490 | Providing,laying,testing&commissioningof "C"class heavydutyMSpipeconformingtoIS3589/IS1239 includingWelding,fittingslikeelbows,tees,flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 491 | Note: Threaded joint upto 50mm diameter pipe. |
| 492 | Welded joint above 50mmdiameter pipe. |
| 493 | 25 mm nominal bore (class C) |
| 494 | 32 mm nominal bore (class C) |
| 495 | 40 mm nominal bore (class C) |
| 496 | 50 mm nominal bore (class C) |
| 497 | 65 mm nominal bore (class C) |
| 498 | 80 mm nominal bore (class C) |
| 499 | 100 mm nominal bore (class C) |
| 500 | Providing,laying,testing&commissioningof"B"class heavydutyG.I.pipeconformingtoIS1239including welding,fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two ormorecoatsofsyntheticenamelpaintofrequired shade complete as required: 80mm |
| 501 | SPRINKLER SYSTEM |
| 502 | Providing, fixing, testing & commissioning of installationcontrolvalveofcastironbody, brass/bronzeworking partscomprisingofwater motor alarm,bronzeseatclapper,clapperarmand hydraulicallydrivenmechanicalgongbelltosound continuousalarmwhenthewetriser/sprinklersystem activates,pressuregauges,emergencyreleases, strainer,pressureswitch,cockvalvecompletewith drainvalveandbypass,testcontrolbox,ballvalves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes asrequired : |
| 503 | Providing, fixing, testing & commissioning of 15mm diaquartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : |
| 504 | Pendent Sprinkler |
| 505 | Upright Sprinkler |
| 506 | Horizontal side wall sprinkle |
| 507 | FIRE EXTINGUSHER |
| 508 | Providing, storing, handling, shifting, installation, testing and commissioning of portable fire Extinguishers as described below: |
| 509 | 4.5 kg carbon dioxide extinguisher, IS marked, with high pressure discharge tube, horn, control valve, CCE approved cylinder |
| 510 | 6 kg Mono Ammonium Phosphate (ABC) type cartridge operated extinguishers |
| 511 | FIRE BUCKET WITH SAND WITH SET OF 4 PAIR |
| 512 | Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : |
| 513 | Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. |
| 514 | Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-"F" insulation, conforming to IS-325. |
| 515 | M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. |
| 516 | Suitable cement concrete foundation duly plastered with anti vibration pads. |
| 517 | 1620 lpm at 70 m Head (For Hydrant & Sprinkler System). |
| 518 | 180 lpm at 70 m Head (For Hydrant & Sprinkler System). |
| 519 | Note: *The head of the pump is selected in a manner so as to give a minimum 3.5kgf/cm2 pressure at the highest/farthest point. |
| 520 | INTERNAL EIECTRICAL WORK |
| 521 | Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required. |
| 522 | Group A |
| 523 | Group B |
| 524 | Group C |
| 525 | Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required. |
| 526 | Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 527 | Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 2 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 528 | Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required |
| 529 | CIRCUIT / SUBMAIN WIRING |
| 530 | 2x1.5sq mm + 1x1.5 sq mm earth wire |
| 531 | 2x2.5sq mm + 1x2.5 sq mm earth wire |
| 532 | 2x6 sq mm + 1x6 sq mm earth wire. |
| 533 | 2x10 sq mm + 1x6 sq mm earth wire. |
| 534 | 2x16 sq mm + 1x6 sq mm earth wire. |
| 535 | 4x2.5sq mm + 2x2.5 sq mm earth wire |
| 536 | 4x6 sq mm + 2x6 sq mm earth wire. |
| 537 | 4x10 sq mm + 2x6 sq mm earth wire. |
| 538 | 4x16 sq mm + 2x6 sq mm earth wire. |
| 539 | Supplying and drawing 2 pair 0.5 mm dia FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair |
| 540 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 541 | Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 542 | 20mm dia |
| 543 | 25mm dia |
| 544 | 32mm dia |
| 545 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 546 | 5/6 amps one way switch |
| 547 | 15/16 amp one way switch |
| 548 | 5/6 amp 3 pin socket outlet |
| 549 | 5/16 amp 6 pin socket outlet |
| 550 | Telephone Socket Outlet |
| 551 | TV anteena Socket Outlet |
| 552 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 553 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 554 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. |
| 555 | 1 or 2 Module (78mm x 78mm x 45mm) - For Telephone & TV outlet. |
| 556 | 4/5 Module (78mm x140mm x 50mm) |
| 557 | 6 Module (78mmX205mmx50mm) |
| 558 | 8/9 Module (78mmX230mmx60mm) |
| 559 | 12 Module (135mmX205mmx60mm) |
| 560 | Supplying and fixing 2 pin 5 Amp Ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 561 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 562 | Supplying and fixing Dingdong sound call bell single phase, 230 volts, complete as required. |
| 563 | Installation, testing and commissioning of pre wired fluorescent fitting / Compact fluorescent fitting off all type complete with all accessories and tube etc directly / wall including connection with 1.5 sq.mm FR PVC insulatted. copper conductor single core cable and earthing etc. as required. |
| 564 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, etc. as required. |
| 565 | Installation of exhaust fan up 450 mm sweep in the existing opening including making the hole to suit the size of above the fan, making good the damage, connection, testing, commissioning etc. as required. |
| 566 | Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 567 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). (For UPS Supply) |
| 568 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. |
| 569 | 20mm dia |
| 570 | 25mm dia |
| 571 | Supply & drawing following sizes of FR PVC insulated copper conductor single core cables in existing surface/recessedsteel / PVC conduit including dismantling as required. 2 x 1.5 sq.mm |
| 572 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 573 | 8 WayDouble Door |
| 574 | 12 WayDouble Door |
| 575 | Supplying and fixing following ways, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 576 | 6 Way (4+18), Double Door Horizontal Type |
| 577 | 8 Way (4+24), Double Door Horizontal Type |
| 578 | Supplying and fixing following ways surface / recess mounting Vertical type 415 Volts TPN MCB distribution board, of sheet steel dust protected duly power painted inclusive of 200 Amps tinned copper bus bar common, neutral link, earth bar, din bar, for mounting MCB"s (But without MCB"s and incomer) as required. ( Note:- Vertical Type MCB TP DB is normally used where 3phase outlets are required. |
| 579 | 8 Way (4+18), Double Door Vertical Type |
| 580 | 12 Way (4+24), Double Door Vertical Type |
| 581 | Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA"C" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required. |
| 582 | 6 / 32 Amp Single Pole |
| 583 | 40 Amp DP |
| 584 | 50/63 Amp DP |
| 585 | 6/32 Amp TPN |
| 586 | 40 Amp TPN |
| 587 | 50/63 Amp TPN |
| 588 | Supplying and fixingSingle pole blanking plate in the existing MCB DBcomplete etc. as required. |
| 589 | Supplying and fixing of following rating double pole ( Single pole & neutral),240 volts, resudual current circuit breaker (RCCB), having a sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc as required. |
| 590 | 16/25 Amps |
| 591 | 40 Amps |
| 592 | 63 Amps |
| 593 | Providing and fixing M.V. danger Notice plate of 200mm x 150 mmof made of mild steel, at least 2 mm thick and vitreous enamelded white on both side and with inscription in single red colour in front side as requird |
| 594 | Providing and fixing H.T. danger Notice plate of 250mm x 200 mmof made of mild steel, at least 2 mm thick and vitreous enamelded white on both side and with inscription in single red colour in front side as requird |
| 595 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required. |
| 596 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required. |
| 597 | Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. |
| 598 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required |
| 599 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 600 | Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. |
| 601 | Providing and fixing 50 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required(2*rate) |
| 602 | Providing and fixing of lighting conductor finial made of 25 mm dia 300 mm long, GI tube having single prong at top with 85 mm dia 6mm thick G.I Base plate including hole etc. as required |
| 603 | Providing and fixingGI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. (for Horizental Run) |
| 604 | Providing and fixingGI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. (for Vertical Run) |
| 605 | Providing and fixing testing Jointing made of20mmx 3mm thick G.IStrip 125 mm Long. With 4 nos of G.I bolts. Nuts chuck nuts and spring washers etc. as required |
| 606 | Providing and LayingG.I tape 32mm x 6mmfrom earth electrode directoly in ground as required. |
| 607 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 608 | 120 mm dia (OD-120 mm & ID-103 mm nominal) |
| 609 | 200 mm dia (OD-200 mm & ID-175 mm nominal) |
| 610 | INSPECTION CHAMBER: |
| 611 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : |
| 612 | Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets. |
| 613 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 614 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. |
| 615 | 1 run of cable |
| 616 | 2 run of cable |
| 617 | 3 run of cable |
| 618 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 619 | Upto 35 sq. mm |
| 620 | Above 35 sq. mm and upto 95 sq. mm |
| 621 | Above 95 sq. mm and upto 185 sq. mm |
| 622 | Above 185 sq. mm and upto 400 sq. mm |
| 623 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. |
| 624 | Upto 35 sq. mm |
| 625 | Above 35 sq. mm and upto 95 sq. mm |
| 626 | Above 95 sq. mm and upto 185 sq. mm |
| 627 | Above 185 sq. mm and upto 400 sq. mm |
| 628 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. |
| 629 | Upto 35 sq. mm (clamped with cable tie) |
| 630 | Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie) |
| 631 | Above 95 sq. mm and upto 185 sq. mm (clamped with cable tie) |
| 632 | Above 185 sq. mm and upto 400 sq. mm (clamped with cable tie) |
| 633 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 634 | 2 x 6 sq. mm (19mm) |
| 635 | 2 X 10 sq. mm (19mm) |
| 636 | 2 X 16 sq. mm (22mm) |
| 637 | 3½ X 35 sq. mm (32mm) |
| 638 | 3½ X 50 sq. mm (35mm) |
| 639 | 3½ X 70 sq. mm (38mm) |
| 640 | 3½ X 95 sq. mm (45mm) |
| 641 | 3½ X 120 sq. mm (50mm) |
| 642 | 3½ X 150 sq. mm (50mm) |
| 643 | 3½ X 185 sq. mm (57mm) |
| 644 | 3½ X 240 sq. mm (62mm) |
| 645 | 3½ X 300 sq. mm (70mm) |
| 646 | 4 X 10 sq. mm (25mm) including 4x6 sq.mm |
| 647 | 4 X 16 sq. mm (28mm) |
| 648 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 649 | 100 mm wide x 50 mm depth x 1.6 mm thickness. |
| 650 | 150 mm wide x 50 mm depth x 1.6 mm thickness. |
| 651 | 300 mm wide x 50 mm depth x 1.6 mm thickness. |
| 652 | 450 mm wide x 50 mm depth x 2.0 mm thickness. |
| 653 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 654 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 655 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 656 | 100 mm wide x 50 mm depth x 1.6 mm thickness. |
| 657 | 150 mm wide x 50 mm depth x 1.6 mm thickness. |
| 658 | 300 mm wide x 50 mm depth x 1.6 mm thickness. |
| 659 | 450 mm wide x 50 mm depth x 2.0 mm thickness. |
| 660 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 661 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 662 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 663 | 100 mm wide x 50 mm depth x 1.6 mm thickness. |
| 664 | 150 mm wide x 50 mm depth x 1.6 mm thickness. |
| 665 | 300 mm wide x 50 mm depth x 1.6 mm thickness. |
| 666 | 450 mm wide x 50 mm depth x 2.0 mm thickness. |
| 667 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 668 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 669 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. |
| 670 | 100 mm width X 50 mm depth X 1.6 mm thickness |
| 671 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 672 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 673 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 674 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 675 | 750 mm width X 62.5 mm depth X 2 mm thickness |
| 676 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 677 | 100 mm wide x 50 mm depth x 1.6 mm thickness. |
| 678 | 150 mm wide x 50 mm depth x 1.6 mm thickness. |
| 679 | 300 mm wide x 50 mm depth x 1.6 mm thickness. |
| 680 | 450 mm wide x 50 mm depth x 2.0 mm thickness. |
| 681 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 682 | 750 mm width X 62.5 mm depth X 2 mm thickness |
| 683 | Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required |
| 684 | 125 A 15kA SC for 1 sec (including100A) |
| 685 | 200 A 25kA SC for 1 sec |
| 686 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes cubicle panel, making connections, etc. as required. |
| 687 | 100 A, 25 KA,TPMCCB |
| 688 | 200 A, 25 KA,TP MCCB |
| 689 | MAIN L.T. PANEL |
| 690 | Design, Manufacturing, Supply, Receiving, Unloading, Shifting, Installation, Testing & commissioning of Main LT Panel. The panel will be totally enclosed type with, free standing, floor mounted, indoor duty, dust & vermin proof, compartmentlized, front operated, electrical panel fabricated from 2 mm thick M.S. Sheetas per specifications & drawing laid in this document and will be complete with the main and auxiliary bus bars, ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indication lamps, CT"s, protection MCB, interconnection wiring, earth bus and will be powder coated finish with 70 micron thickness. All the busbar joint shall be protected by clip on type sleeve. The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. |
| 691 | INCOMERS from 1 Nos. 315 KVA Transformers |
| 692 | 1nos. 630AMP.Four Pole,Electrically operated 3 position motorized (220 V AC) drawout typeAir Circuit Breaker with all inbuilt protections, with microprocessor basedrelease, over current, earth fault, short circuit, Instantaneous short circuit, closing coil (220 V AC), trip coil (24 V DC), shunt trip release, inbuilt U/V release withLCD / LED display for event history & measurement of current parameters, 50 KA Breaking Capaciy with all standard accessories i.e. auxillary switch with 4NO + 4NC contacts, cradle, handle, safety shutter in confirmity with IS:60947 |
| 693 | Protection releases / relays, Metering & Accessories for each Transformer incomers |
| 694 | Over Voltage / Under Voltage relay / release (3 phase) with timer. |
| 695 | Master trip relay. |
| 696 | Trip Circuit Supervison relay. |
| 697 | TNC switch. |
| 698 | Auto manual selector switch. |
| 699 | 1 nos. 0-500 volt range digital type voltmeter with selector switch |
| 700 | 1 set of 3 CT"s of ratio 600/5A, Class 1.0 accuracy 15 VA burden for metering. |
| 701 | 1 set of 3 CT"s of ratio 600/5A, Class 1.0 accuracy 15 VA burden for APFCR. |
| 702 | 1 set of 4 CT"s of ratio 600/1A, Class PS for protection. |
| 703 | 1 no. CT"s of ratio 600/5A, Class 5P10 for protection. |
| 704 | 1 no. 0-600 Amprange digital type ammeter with selector switch. |
| 705 | Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of Conzerve or equi.) with RS 485communication port for communication / report generation. (or Dual meter) |
| 706 | Power factor meter. |
| 707 | Frequency meter. |
| 708 | 3 Nos. LED type phase indicating lamps, each lamp shall be with bakup MCB along with hooter, auxillary relay, 2 sets of push buttons. |
| 709 | 5 Nos. LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy. Each lamp shall be with bakup MCB. |
| 710 | BUSBARS |
| 711 | 800 AmpTPN busbars of aluminium alloy as per SLD. |
| 712 | OUTGOING |
| 713 | 01 Nos 315A FP MCCB (25KA) |
| 714 | 01 Nos 200A TP MCCB (25KA) |
| 715 | 03 Nos 100A TP MCCB (25 KA) |
| 716 | 04 Nos 63A TP MCCB (25 KA) |
| 717 | 06 No 63A FP RCCB (300 mA) |
| 718 | Main L.T. Panel Described as Above. |
| 719 | AUTOMATICPOWERFACTORCORRECTIONPANEL(CAPACITOR PANEL) |
| 720 | Design, Manufacturing, Supply, Receiving, Unloading, Shifting, testing & commissioning of 14 SWG CRCA sheet steel fabricated cubical type 100 KVAR A P F C Panel consisting of 5 /10 / 25 / KVAR (at 415 Volts rated voltage of bank shall be 440 Volts) capacitor units in tier formation, housed in an integrated cubicle type automatic switching ON and OFF control panel, floor mounting, dust & vermin proof, front operatedconstruction, enclosure class - IP 42, powder coated after proper treatment with 9 tank process with top/bottomremovable gland plates, as required, double compression type cableglands,earth bus, hinged and lockable doorsto achieve dust and vermin proofcomplete with all inter connectionssmall wiring by min. 2.5 sq. mm. copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per IS 8623 . |
| 721 | All out going MCCB"s shall be thermal-magnetic based with inbuiltO/L & S/C release. |
| 722 | All MCCB"s shall be Ics = 100% Icu, with rotary handle & pad locking arrangement, with adjustable O/L &S/Ctrip setting as per load requirement. All TP MCCB shall be with heavy duty solid isolable neutral link.The breaking capacity specified is Ics value. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmeter, selector switches, CT"s, PT"s, etc. |
| 723 | AC3 duty contactors should be used for switching individual capacitor banks. |
| 724 | The fault withstanding capacity of panel & its control gear shall be min. 50 KA rms for 1 sec. |
| 725 | Each section of capacitor panelshall have Verticle hood & exhaust fans for ventilation purpose. |
| 726 | INCOMING |
| 727 | Incomer circuit breaker has been included in the main panel. |
| 728 | 1 set-3 CTs , ratio 200 / 5A Class 1.0 accuracy 15 VA burden for metering. |
| 729 | 1Nos- (200 A)digitalAmmeter withselector switch |
| 730 | Micro processor based automatic power factor control relay (3 phase) (including power factor meter) in 13 steps for automatic cut off or add on capacitor units to keep the power factor at 0.95 with variation of loads. All associated auxiliary contactors / relays shall be provided with in the scope of work. |
| 731 | Phase indicating lamps with HRC fuses, and indicating in each capacitor chamber unit to indicate On/Off status of capacitor unit. |
| 732 | BUS BARS |
| 733 | 200 AMP,500 Volts, 3 phase 50 HZTPN high conductivity electrolytic Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clips on shrouds for joints. |
| 734 | OUTGOINGS |
| 735 | 3 nos.of 63AMPS TPN MCB (25 KA) and 80 amps AC3 duty contactor with 25 KVAR,MPP resin filled, super heavy duty ,440 V capacitor bank, start stop push button for manual operation including on/off indicating lamps and delay timer complete. |
| 736 | 2 nos.of 32AMPS TPN MCB (10 KA) and 40 amps AC3 duty contactor with 10 KVAR,MPP resin filled, super heavy duty ,440 V capacitor bank, start stop push button for manual operation including on/off indicating lamps and delay timer complete. |
| 737 | 1 no.of 16AMPS TPN MCB (10 KA) and 20 amps AC3 duty contactor with 5 KVAR,MPP resin filled, super heavy duty ,440 V capacitor bank,start stop push button for manual operation including on/off indicating lamps and delay timer complete. |
| 738 | Capacitor Panelas described above |
| 739 | DG PANEL |
| 740 | Design, Manufacturing, Supply, Receiving, Unloading, Shifting, Installation, Testing & commissioning of DG Panel. The panel will be totally enclosed type with, free standing, floor mounted, indoor duty, dust & vermin proof, compartmentlized, front operated, electrical panel fabricated from 2 mm thick M.S. Sheetas per specifications & drawing laid in this document and will be complete with the main and auxiliary bus bars, ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indication lamps, CT"s, protection MCB, interconnection wiring, earth bus and will be powder coated finish with 70 micron thickness. All the busbar joint shall be protected by clip on type sleeve. The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. The panel shall havechangeover facility & interlocking through PLC to achieve electrical interlocking, buscoupler switching, auto operation of incommer and bus coupler etc and having following incomming and outgoing Air Circuit Breakers, MCCB as per the drawing and specification. |
| 741 | INCOMERS frommain LT Panel |
| 742 | 1 Nos. 315A MCCB with 315 A 4P Contractor |
| 743 | Protection releases / relays, Metering & Accessories for each Transformer incomers |
| 744 | Auto / manual / test selector switch |
| 745 | 0-500 volt range digital type voltmeter with selector switch |
| 746 | 1 set - 3 CTs of ratio :300/5A , Class 1.0 accuracy 15 VA each burdenfor metering. |
| 747 | Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of Conzerve or equi.) with RS 485communication port for communication / report generation. (or Dual meter) |
| 748 | 3 Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC fuse/MCB along with hooter, auxillary relay, 2 sets of push buttons. |
| 749 | INCOMERS from1Nos. 160 KVA D G sets |
| 750 | 1 Nos. 315A MCCB with 315 A 4P Contractor |
| 751 | Protection releases / relays, Metering & Accessories for each D G set incomers |
| 752 | Over Voltage / Under Voltage relay / release (3 phase) with timer. |
| 753 | Reverse power relay. |
| 754 | Auto / manual / test selector switch |
| 755 | 0-500 volt range digital type voltmeter with selector switch |
| 756 | 1 set - 3 CTs of ratio :300/5A , Class 1.0 accuracy 15 VA each burdenfor metering. |
| 757 | 1 set - 3 CTs of ratio :300/5A , Class 5P20 accuracy 20 VA each burdenfor protection. |
| 758 | 0-300 Amprange digital type ammeter with selector switch. |
| 759 | Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of Conzerve or equi.) with RS 485communication port for communication / report generation. (or Dual meter) |
| 760 | 3 Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC fuse/MCB along with hooter, auxillary relay, 2 sets of push buttons. |
| 761 | 5 Nos. LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy. Each lamp shall be with bakup HRC fuse/MCB. |
| 762 | Shut down due to low lube oil pressure/High water temp/Over speed/Low fuel level - set of 4 indication lamps. |
| 763 | D G control incorporating engine start / stop indicating three attempt facility and on failure to start, engine lock out. |
| 764 | 1 nos battery charger with DC voltmeter and ammeter suitable for the DG sets (160 KVA) |
| 765 | Note : In normal case all three lamps shall be ON to indicate that incoming power supply is available. In case of power resumption after failure buzzer shall ring to indicate the power supply is resumed. There shall be one push button to acknowledge the same. |
| 766 | The ACB shall be electrically interlocked with the bus coupler and Transformer incomers. |
| 767 | BUSBARS |
| 768 | 500 AmpTPN busbars of aluminium alloy as per SLD. |
| 769 | OUTGOING |
| 770 | 01 Nos 315A TP MCCB(25KA) |
| 771 | 03 Nos 200A TP MCCB (25KA) |
| 772 | 02 Nos 100A TP MCCB (25 KA) |
| 773 | 04 Nos 63A TP MCCB (25 KA) |
| 774 | 03 Nos 40A TP MCCB (25 KA) |
| 775 | 03 Nos 63A FP RCCB (300 mA) |
| 776 | Main L.T. Panel Described as Above. |
| 777 | DISTRIBUTION PANEL |
| 778 | Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of cubicle type totally enclosed free standing type moisture, dust and vermin proofFloor Distribution Panel made out of 2.0 mm thick & front cover 1.6 mm thickCRCA sheet complete with followingequipments, includingdigital ammeter with inbuilt ammeter selector switch, digital voltmeter with inbuilt voltmeter selector switch, indicating lamps, CT"s, internal wiring with suitablesize wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics.The incoming MCCB shall be microprocessor based with O/L & S/C and E/F protection and all Outgoings up to 250A MCCB"s may be thermo-magnetic basedO/L & S/C protection. All outgoing MCB"s shall be C type with 10 KA breaking capacity. |
| 779 | L+P PANEL ( GROUND & FIRST) |
| 780 | INCOMING |
| 781 | 1 No. 200 Amp FP MCCB (25 KA) |
| 782 | 1 No.AVF Meter with inbuilt selector switch. |
| 783 | 1 Set of phase indicating lamps with Single Pole MCB. |
| 784 | 1 Set of ON / OFFindicating lamps with Single Pole MCB. |
| 785 | BUSBAR |
| 786 | 300 Amp FPaluminium busbar with coloured heat shrinkable sleeve. |
| 787 | OUTGOING |
| 788 | 12 Nos. 25 Amp FP MCB (10 KA) |
| 789 | 4 Nos. 40 Amp FP MCB (10 KA) |
| 790 | 12 Nos. 63 Amp FP MCB (10 KA) |
| 791 | Panel described as above |
| 792 | UPS PANEL ( GROUND FLOOR ) |
| 793 | INCOMING |
| 794 | 2 No. 200 Amp FP MCCB (35 KA) |
| 795 | 2 No.AVF Meter with inbuilt selector switch. |
| 796 | 2 Set of phase indicating lamps with Single Pole MCB. |
| 797 | 2 Set of ON / OFFindicating lamps with Single Pole MCB. |
| 798 | BUSBAR |
| 799 | 300 Amp TPN copper busbar with coloured heat shrinkable sleeve. |
| 800 | OUTGOING |
| 801 | 1 Nos. 100Amp FP MCCB (25 KA). |
| 802 | 4 Nos. 63Amp FP MCB (10 KA). |
| 803 | 10 Nos. 40Amp FP MCB (10 KA). |
| 804 | 10 Nos. 40Amp DP MCB (10 KA). |
| 805 | 6 Nos. 63Amp DP MCB (10 KA). |
| 806 | Panel described as above |
| 807 | EXTERNAL LIGHTING PANEL (OUTDOOR TYPE) |
| 808 | Design, Manufacturing, Supply, installation, Testing & Commissioning of Outdoor Type Panel with Front & Back double door, Top canopy, Mounting on Floor M.S. Stand etctotally enclosed free standing type water, moisture, dust and vermin proof Sub Distribution Board made out of 2.0 mm thick CRCA sheet complete with followingequipments, includingammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, CT"s, internal wiring with suitablesize wires/ cable, interconnection, painting etc as required. |
| 809 | INCOMING |
| 810 | 1 No 100 Amp FP Moulded Case Circuit Breaker (35 KA) with 100 Amp 4 Pole Contactor & Timer. |
| 811 | 1 No. Digital AVF Meter with inbuilt selector switch and CT" & SP MCB. |
| 812 | 1 Set of phase indicating lamps. |
| 813 | 1 Set of ON/OFF indicating lamps with SP MCB. |
| 814 | BUS BARS |
| 815 | 200 Amp FP aluminium busbar with coloured heat shrinkable sleeve. |
| 816 | OUTGOING |
| 817 | 08 Nos. 25 Amp DP MCB(10 KA) |
| 818 | 03 Nos. 40 Amp DP MCB(10 KA) |
| 819 | Panel described as above |
| 820 | DISTRIBUTION PANEL- |
| 821 | Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of cubicle type totally enclosed free standing type moisture, dust and vermin proofFloor Distribution Panel made out of 2.0 mm thick & front cover 1.6 mm thickCRCA sheet complete with followingequipments, includingdigital ammeter with inbuilt ammeter selector switch, digital voltmeter with inbuilt voltmeter selector switch, indicating lamps, CT"s, internal wiring with suitablesize wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics.The incoming MCCB shall be microprocessor based with O/L & S/C and E/F protection and all Outgoings up to 250A MCCB"s may be thermo-magnetic basedO/L & S/C protection. All outgoing MCB"s shall be C type with 10 KA breaking capacity. |
| 822 | METER BOARD PANEL - 1 |
| 823 | INCOMING |
| 824 | 1 No. 100 Amp FP MCCB (25 KA) |
| 825 | 1 No.AVF Meter with inbuilt selector switch. |
| 826 | 1 Set of phase indicating lamps with Single Pole MCB. |
| 827 | 1 Set of ON / OFFindicating lamps with Single Pole MCB. |
| 828 | BUSBAR |
| 829 | 200 Amp FPaluminium busbar with coloured heat shrinkable sleeve. |
| 830 | OUTGOING |
| 831 | 07 Nos. 40 Amp DP Miniature Circuit Breakerwith KWH Meter. |
| 832 | Panel described as above |
| 833 | METER BOARD PANEL - 2 |
| 834 | INCOMING |
| 835 | 1 No. 100 Amp FP MCCB (25 KA) |
| 836 | 1 No.AVF Meter with inbuilt selector switch. |
| 837 | 1 Set of phase indicating lamps with Single Pole MCB. |
| 838 | 1 Set of ON / OFFindicating lamps with Single Pole MCB. |
| 839 | BUSBAR |
| 840 | 200 Amp FPaluminium busbar with coloured heat shrinkable sleeve. |
| 841 | OUTGOING |
| 842 | 01 Nos. 40 Amp DP Miniature Circuit Breakerwith KWH Meter. |
| 843 | 06 Nos. 40 Amp FP Miniature Circuit Breakerwith KWH Meter. |
| 844 | Panel described as above |
| 845 | Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming toIS-7098. (Part-I). |
| 846 | 3.5 core,300 sq.mm. |
| 847 | 3.5 core,240 sq.mm. |
| 848 | 3.5 core,185 sq.mm. |
| 849 | 3.5 core,150 sq.mm. |
| 850 | 3.5 core,120 sq.mm. |
| 851 | 3.5 core,95 sq.mm. |
| 852 | 3.5 core,70 sq.mm. |
| 853 | 3.5 core,50 sq.mm. |
| 854 | 3.5 core,35 sq.mm. |
| 855 | 4 core,16 sq.mm. |
| 856 | 4 core,10 sq.mm. |
| 857 | 4 core,6 sq.mm. |
| 858 | 2 core,16 sq.mm. |
| 859 | 2 core,10 sq.mm. |
| 860 | 2 core,6 sq.mm. |
| 861 | Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor PVC insulated cable including termination complete as required in existing cable tray. |
| 862 | 1C x 50 sq.mm PVC Insulated cu wire including termination etc. |
| 863 | 1C x 16 sq.mm PVC Insulated cu wire including termination etc. |
| 864 | Supply, erection, testing and commissioning of following sizes of TV splitter of aluminium die cast body in suitable size of G.I. Box. 4 way |
| 865 | Supply, erection, testing and commissioning of following co-axial cable in existing conduit. RG-11 |
| 866 | Supply & installation of 32 Amp 3 phase, 415 volt, 50 Hz water tight (IP-55) socket outlet with interlocking switch complete with all fixing accessories. |
| 867 | Supply & installation of 32 Amp single phase 240 Volt, 50 Hz, water tight (IP-55) socket outlet with interlocking switch complete with all the fixing accessories as below. |
| 868 | Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet) race ways for electrical & LV wiring including neoprene gasket in joints, cutting the floor & jaming the race way / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work) as per site requirement. The thickness of raceway & cover shall be as per technical specification. |
| 869 | 100 mm wide x 40 mm deep. |
| 870 | 200 mm wide x 40 mm deep. |
| 871 | Supply & fixing of following size of Raceway Junction Box made out of GP Sheet for electrical & LV wiring including, cutting the floor & jaming the junction box / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work).(Junction box to be provided as per drawing/ as per site requirement & as per specification). The thickness of junction box shall be a as per thechnical specification. |
| 872 | 150 mm wide x 50 mm deep. |
| 873 | 250 mm wide x 50 mm deep. |
| 874 | Supply, Installation, Testing & Commissioning of Earthing Junction Box size - 400mm x 300mm x 80mm made out of 16 SWG CRCA sheet with seven tank process & powder coating, earthing link (32mm x 6mm copper strip) front door with glass as complete as required. |
| 875 | FIRE ALARM SYSTEM (ADDRESSABLE TYPE) AND PA SYSTEM |
| 876 | Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. |
| 877 | Two Loop Panel. |
| 878 | Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. |
| 879 | Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector acclimate type sensetive level (0.524%) OVS/ft. complete with mounting base complete as required. |
| 880 | Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required. |
| 881 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. |
| 882 | Supplying, installation, testing & commissioning of addressable fire control module complete as required. |
| 883 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. (75 DBA @3 mtr. & 75CD flashing) |
| 884 | Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. |
| 885 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 886 | Supply, installation, testing and commissioning of addressable monitor module complete as per specification. |
| 887 | Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. |
| 888 | Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. |
| 889 | Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required. |
| 890 | Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required. |
| 891 | Supplying, installation, testing & commissioning of digital audio amplifier 480 Watt, supply complete as required. |
| 892 | Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable Single pair, 2-core, 1.5 sqmm |
| 893 | SUPPLY & INSTALLATION OFLIGHT FIXTURES & FANS |
| 894 | SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required.Make:- Havells/Philips/Crompton/Wipro / India Bulls. |
| 895 | 12W LED Round Down Light (Recess ) |
| 896 | 15 / 16 W LED Round Down Light(Recess ) |
| 897 | 18 /20 W LED Round Down Light (Surface) |
| 898 | 18 /20 W LED Round Down Light (Recess) |
| 899 | 2" x 2" LED Panel Light (Recess) |
| 900 | Bulk Head fitting with 9/10Watt LED. |
| 901 | S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required. |
| 902 | 10/12 W LED Tube Light |
| 903 | 20/22 W LED Tube Light |
| 904 | 30 WCOB based round LED Light with multiple beam angles (36 Degree) |
| 905 | SITC of300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Usha/Crompton / Havells . |
| 906 | Supply Installation, Testing & Commissioning of following sizes ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard (up to 30cm) with 1.5 sq.mm FR PVC insulated copper wire suitable for 230V 50 Hz, Single phase supply etc. complete as required. Make :- Usha/Crompton / Havells . |
| 907 | 1200 mm ( 48") BLDC 5 Star rating 32W Ceiling Fan |
| 908 | UPS SYSTEM |
| 909 | Supply, fitting, fixing,testing and installation of40 KVA, ON Line UPS three phase input and three phase out put power system of in put voltage range 360V/380/V/400V/485V AC , Frequency range 40 HZ to 60 Hz, +/- 10%and out put voltage range 415V +/-1%,AC frequency range, 50Hz, +/-1%poower factor 0,8/3.1, Harmonic distrortion -< 2% THD (Linear Load): 5% THD (Non- Liniear Load) along with required Batteries, Battery Stand, UPS Box Battery Lead etc as required. |
| 910 | UPS shall carry design output at 40 deg. |
| 911 | Shall have soft start and hold of for incoming supply. |
| 912 | Invertor capability to supply 150% load for 5 sec. |
| 913 | SNMP card, compatible for BMS connectivity on backnet/MODBUS, Inbuilt Isolation transforme. |
| 914 | Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. |
| 915 | Battery shall be external type with rack and suitable for 30 minute backup on 100% load. |
| 916 | Suitable size of copper cable between UPS and battery bank shall be provided |
| 917 | UPS shall be compatible for 3 nos unit in parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS. |
| 918 | SITC of MS Battery Rack suitable for 40 to 50 UPS Battery Installation. |
| 919 | SITC of60 nos. 65 AH Flat type Sealed Maitanace Free (SMF) Battery with 24 months replacement warranty. IS:1652:1991. (VAH Required minimum46800 for 40 KVA UPS (65AH x 60 Nos. x 12V = 46800 VAH) |
| 920 | Total cost of 1 Set 40 KVA UPS, Batteries& Accessories (A+B+C) |
| 921 | DATA, TELEPHONE SYSTEM INCLUDING ACTIVE COMPONENTS |
| 922 | Supply, Installation, Testing & Commissioning ofCat 6, 24 Port Patch Panel |
| 923 | Supply, Installation, Testing and Comissioning of Cat 6 patch cord 3 feet for rack and user end termination - 1Mtr |
| 924 | Supply, Installation, Testing and Comissioning of Cat 6 patch cord 7 feet for rack and user end termination - 2Mtr |
| 925 | Supply, Installation, Testing, Commissioning of Cat 6, Information Outlet (I/O) including G.I. Box and modular cover plate. |
| 926 | Supply, Installation, Testing and Comissioning of 24U floor mounted Rack with accessories. |
| 927 | Supply, Installation, Testing & Commissioning of 24 port 10/100/1000Mbps, 4SFP module,L-2 Switch, POE. |
| 928 | Supply, Installation, Testing & Commissioning of EPABX SYSTEM Configuration as Below:- Analog Trunk Line6 Nos. Digital Line2 Nos Analog Extensions 60 Nos. |
| 929 | Supply, Installation, Testing & Commissioning of Digital Phone for Operator Console |
| 930 | Supply, Installation, Testing & Commissioning of TypeAnalog Phone with speaker phone, . |
| 931 | Supply, Installation, Testing & Commissioning of 6 Core OM4 Multimode Fiber Cable. |
| 932 | Supply and fixing of telephone distribution board (tagblocks) in hinged type MS box duly powder coated complete with bakelite sheetwith termination of incoming and outgoing telephone wire etc. complete as required.10pair telephone distribution board. |
| 933 | Supply and wiring of telephone tag blockwith 0.5mm dia annealed tinned copper conductor PVC insulated and PVC sheathed unarmoured telephone cable in existing conduit in concealed/ surface system / existing cable tray complete as required.10pair telephone unarmoured cable. |
| 934 | IP CCTV SYSTEM |
| 935 | Supplying, installation, testing & commissioning of 1080p HD Indoor IP Dome camera with1/3-inch CMOS, Sensor pixels 1920 x 1080, Sensitivity-0.04 lx (color) , Dynamic range 75 dB Wide Dynamic Range (WDR), True day/night, Automatic Electronic Shutter, Video compression H.264 ; M-JPEG, White balance, BLC, H.264 quad-streaming, Motion/tamper/audio detection, Privacy Mask, Lens 3.6 mm lens, 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE Certified. |
| 936 | Supplying, installation, testing & commissioning of 5MP 30 fps HD indoor / outdoor IR IP bullet camera with 1/3-inch CMOS, Sensor pixels 2612 (H) x 1980(V), Sensitivity-0.24 lx (color) 0.04 lx (mono) ,IR range 30 mtrs,Dynamic range 70 db, True day/night, Automatic Electronic Shutter, Video compression H.264 MP ; M-JPEG, White balance, BLC, Analog video output,Lens (zoom / focus) 3.6 mm lens, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 ,ONVIF Profile S, CE Certified. |
| 937 | Supply installation and commission of pann tilt zoomcamera with 360 deg pan and 90 deg tilt with 36 X Zoom havingmaximum resolution of Max. 1920 × 1080 @30fps,true day night camera with 130 m IR range , optional, fine picture at Ultra-low light,supports compression format H.265, H.265+, H.264+, H.264, 3D Digital Noise Reduction support. |
| 938 | SITC of IP network recoder with following feature Processor - Dual-core embedded processor . Two-way Talk - 1 channel Input, 1 channel Output, RCA,Video Output - 1 HDMI, 1 VGA , IP Camera Input - 8/16/32Channel IP , Compression - H.264+/H.264/MJPEG,Video Resolution - 2560 × 1920, 2048 × 1536, 1920 x 1080, 1280 x 1024, 1280 x 720, 1024 x 768 , Hard Disk - 4 SATA Ports, up to 8TB ,Motion Detection - MD Zones: 396 (22 × 18),Recording Mode - Manual, Schedule (Regular, Continuous), MD (Video detection: Motion Detection, Camera Blank, Video Loss), Alarm, Stop, Backup Mode - USB Device /Network , Interface Ports - 1 HDMI, 1 VGA, 2 USB(1 USB 2.0 , 1 USB 3.0 ), 1 RS485, 1 RS232, 1 RJ45. |
| 939 | Supply, Installation, Testing and commissioning of Managable24 port Switch with Power on Ethernet (PoE) enabled, 10/100,RJ45 Access ports with PoE complete as required. |
| 940 | Supply, installation, testing and commissioning of of 6 TB HDD all accessories complete as required. |
| 941 | Supply installation and commissioning of 48 inch LED monitor for disply of camera. |
| 942 | SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM |
| 943 | Supplying installation testing and commissioning of Grid interactive roof top solar photo voltaic power generation system including all the required accessories like Solar PV module, Grid Tie invertor, arrey junction box, cabling & wiring, earthing, surge protection device, FRLSame structure for mounting of solar panel. The cell shall be poly crystaline silicon cells of 6 inch each and module efficiency shall be more than 17%. Solar module shall have linear output warranty with degradation not exceeding 0.7% FRLSom 2nd Year onwards. Minimum 80% power output must be assured at end of 25 years. The FRLSont glass of solar module shall be low iron tempered glass ARC type. Termination box shall be Thermo-plastic, IP 67 or better, UV resistant with built-in-bypass. The nominal power of a single PV module shall be minimum 325 Wp or higher. Positive power tolerance modules only to be used. RF identification tag for each solar module shall be provided inside the module and must be able to withstand environmental conditions. The solar panel shall be complience of IEC 61215, IEC 61730 certified byTUV Rheinland / UL. The solar panel shall be installed as per BOQ & detailed technical specification. |
| 944 | AUTOMATIC FIRE DETECTION GAS SUPPRESSION SYSTEM IN PANELS |
| 945 | Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based Novec 1230 System for Electrical Panels (consisting of the following components. |
| 946 | 6 KG Novec 1230, DLP Assembly with automatic valve mounted on approved cylinder, push in connector for tube, Novec 1230 gas, mounting bracket, End of Line adopter and low pressure switch for monitoring system activation. |
| 947 | Linear pneumatic heat Detection Tube with all necessary fittings & supports |
| 948 | Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System (Supply to be provide by the end client at 220 Volt AC). |
| 949 | DG SET & SUBSTATION WORK |
| 950 | DIESEL GENERATING SET |
| 951 | Supply,Installation testing and Commissioning ofSilent type Diesel Generating Setwith AMF PANEL at 0.8 PF, 415 Volts, 50 cycles per second, 1500 rpm, 3 phase, suitable for parallel operation / PLC based synchronization, 0.85 load factor including circuit breaker for isolation, sound proof acoustic and weather proof enclosure, residential type silencer (as per CPCB norms-2) fabricated out of CRCA sheet of16 SWG thickness with 9 tank pretreated before powder coating with ventillation system complete in all respects comprising of the following. |
| 952 | Diesel Engine - |
| 953 | Diesel Engine suitable for driving alternator of above rating, compression ignition, 4 stroke cycle, Radiator cooled, turbo charged, battery starting, 1500 RPM, suitable for above output of alternator at 40oC, 50% RH & at 210 M MSL and confirming to BS 5514, BS 649, IS 10000, capable of taking 10% overloading for one hour after 12 hrs of prime continuous loading, complete with all the accessories i.e. tachometer with hour meter, flexible coupling with guard, crank case of steel, crank shaft, conncting rods, electronic governing system, dynamically balanced flywheel, air intake manifold, Air cleaner, anti vibration pads, starter motor, including all other accessories required to complete the system. |
| 954 | Instrument Panel - Engine mounted Instrument Panel fitted withand having digital display for followings : |
| 955 | Start stop switch with key |
| 956 | Water temperature indication |
| 957 | Lubrication oil pressure indication. |
| 958 | Lubrication oil temperature indication. |
| 959 | Battery charging indication |
| 960 | RPM indication |
| 961 | Over speed indication |
| 962 | Low Lube oil trip indication |
| 963 | Engine hours indication |
| 964 | Alternator- |
| 965 | Synchronous Alternator of above capacity at 0.8 PF, 3 phase, 415 volts, 50 cycles, 4 wire, 1500 RPM, suitable for operation at 40 deg C, 50% RH & at 210 meter above MSL, capable of taking 10% overlioading for one hour after 12 hrs of prime continuous loading, brushless, self excited, self regulated through AVR, continuous duty confirming to IS 4722, BS 2613 suitable for tropical conditions, class H insulation, including terminal box suitable for bus duct termination / cable termination as required. |
| 966 | Note : - Alternator should have with all other accessories as per specified in Technical specfications. |
| 967 | Base Frame - Both the engine and alternator shall be mounted on suitable base frame made of MS channel which shall be installed on cement concrete foundation and vibration isolating arrangement as per recommendations of manufacturer. |
| 968 | Inbuilt Fuel tank ofstandard capacity complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, fuel transfer system for automatic fuel refilling system with pump, piping, valves, level indicators etc. complete. |
| 969 | Daily service Fuel tank of990 liters capacity fabricated out of 2 mm thick MS sheet complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, provision for fuel transfer system,level indicators and all standard accessories etc. as required. |
| 970 | Exhaust Silencer - Exhaust manifold with residential silencer. |
| 971 | The D G set should be supplied with required hardware for external PLC based auto synchronization, auto load sharing, auto load management system. |
| 972 | Starting system - 24 Volt DC starting system comprising of starter motors : voltage regulator and arrangement for initial excitation complete with 12/24 Volts suitable nos. lead acid type batteries of suitable AH. |
| 973 | Ventillation System - Arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphere as per standard specifications. |
| 974 | 160 KVA |
| 975 | Supply, Fixing, testing and Commissioning of Exhaust gas piping system ofClass `B" MS pipe as per IS:1239 for upto 150 mm dia and for 200 mm dia & above MS pipe as per IS:3589 with welded joints, cut to required lengths with necessary bends, fittings, flanges, painting over primer coat, with mineral wool / rock wool insulation of minimum 75mm thick of 150 Kg per cu M density on all sides of exhaust pipe, with chicken mesh wrapping and 26 SWG aluminium sheet cladding complete as required. The aluminum foil should be tightly cladded to insulation surface of pipe. The aluminum cladding shall be locked with sheet metal screws with other sections of aluminium foil.The measurement shall be doneon the basis of centre line. (Stack height should be in accordance with emission regulations of CPCB, which will gowell above the top most terrace) The exhaust piping system should be suitable for upto 550oC temperature, the surface temperature of exhaust pipe shall not exceed more than 60oC. (The rates are exclusive of support structure) (Note - Final size of exhaust pipe will beconfirmed by the DG vendor after calculating the actual back pressure and submit the same to client / consultant for approval) |
| 976 | 100 mm dia (wall thickness - 4.85 mm) |
| 977 | Supply & fabrication ofD G exhaust pipe supports by M.S angle iron of size not less than 100 x 50 mm x 6/8 mm duly grouted in the wall through minimum 8 mm thick plate and with suitable MSangle / channel iron structure. The entire MS support structure should be painted by 2 coats of anti corrosive paint over primer coat of approved shade and make. The design of support to be duly approved by the Structural Consultant / Architect before fabrication and installation. |
| 978 | 11 KV HT VCB FOUR BREAKER PANEL BOARD (INDOOR TYPE) |
| 979 | Supplying, Installation, Testing & Commissioning of indoor type floor mounted metal clad, 11 KV VCB panel with 3 nos VCBs, totally inclosed & fully interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and manually closing breaker suitable for use on 11 KV, 3 phase, 50 Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 630 Amp capacity, breaker featured with mechanical ON/OFF indicator with hand trip device. |
| 980 | Spring release coil, shunt trip coil and auxiliary switch of 4 NO + 4 NC and equipped with following switchgears and accessories i/c connections for 3C x 300 sq.mm. XLPE 11 KV cable (cable entry from bottom), end termination with heat shrinkable jointing material etc. as required. (Note - Cost of end termination not included in this item). |
| 981 | a) 1 No, 630 Amp, VCB. |
| 982 | b) 1 No.- 11 KV / 110 Volt PT class 0.5 accuracy and 100 VA burden with 1 No. voltmeter (0-12 KV), digital type, selector switch for voltmeter and protection MCB for HT Metering up to 12 KV on incommer. |
| 983 | c) 1 No.- (0 - 150 A) dual scale Ammeter, digital type, selector switch for ammeters. |
| 984 | d) 1 No - Microprocessor basednumericak relay with O/C, E/F and S/C protection. |
| 985 | e) 1 No - set of dual core dual ratio 3 CTs 100/5A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection. |
| 986 | f) 1 No. electronic type digital energy analyser having 30 days memory and parametersofKW, KWH, Power factor, frequency etc.Suitable for BMS compatible with all accessories. |
| 987 | g) 1 No. hooter with hooter acceptance and reset push button. |
| 988 | h) 1 No - Red, Yellow & Blue for phase indication. |
| 989 | i) 1 No - Amber for Trip indication. |
| 990 | j) 1 No - Red `ON"Green `OFF"indication. |
| 991 | k) 1 No - Springchargeindication. |
| 992 | l) 1 No - Auto trip indication. |
| 993 | m) 1 No. hooter with hooter acceptance and reset push button. |
| 994 | n) 1 No.master trip relay. ( Electromechanical Type ) |
| 995 | o) 1 No.Trip ckt supervision relay. (Electromechanical Type ) |
| 996 | a) Outgoing - 2 No, 630 Amp, VCB. |
| 997 | b) 2 No.- (0 - 100 Amp) dual scale Ammeter, digital type, selector switch for ammeters. |
| 998 | c) 2 No - Microprocessor basednumericak relay with O/C, E/F and S/C protection. |
| 999 | d) 2 No - set of dual core dual ratio 3 CTs 100/5 A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection. |
| 1000 | e) 1 No. electronic type digital energy analyser having 30 days memory and parametersofKW, KWH, Power factor, frequency etc.Suitable for BMS compatible with all accessories. |
| 1001 | f) 2 No. hooter with hooter acceptance and reset push button. |
| 1002 | g) 2 No - Red, Yellow & Blue for phase indication. |
| 1003 | h) 2 No - Amber for Trip indication. |
| 1004 | i) 2 No - Red `ON"Green `OFF"indication. |
| 1005 | j) 2 No - Springchargeindication. |
| 1006 | k) 2 No - Auto trip indication. |
| 1007 | l) 2 No. hooter with hooter acceptance and reset push button. |
| 1008 | m) 2 No.master trip relay. ( Electromechanical Type ) |
| 1009 | n) 2 No.Trip ckt supervision relay. (Electromechanical Type ) |
| 1010 | o) 2 No.auxiliary relay for transformer fault. |
| 1011 | p) Power pack. |
| 1012 | H.T. Panel described as above |
| 1013 | TRANSFORMER |
| 1014 | Design, manufacture, supply, installation, testing and commissioning of out door type copper wound transformer continuously rated for 3Ph 50 Hz at full load rating the transformer should have oil immersed winding having vector group DY-11, HT side connected in star with neutral brought out connected to provide separate earthing. The transformer shall have power terminal arrangement bushing / cable end box on HT side and cable end box on LT side.315 KVA, 11 KV /0.415 KV, 3 phase, 4.5 % impedance, 50Nos channels with stoppers shall be provided and fixed on the provided plinth for mounting the Transformer. The transformer should have following standard as per amended IS specification and the load * no load losses shall be limited to the values given below or as per IS 2026 and latest IS-1180 or Norms issued by SEB which ever are Lower. |
| 1015 | Oil Conservator with filling hole with cap and plain oil level gauge. |
| 1016 | Silica gel dehydrating breather charged with silica gel. |
| 1017 | Oil drain Valve |
| 1018 | Oil Filter Valve |
| 1019 | Lifting eyes / Hooks |
| 1020 | Two earthing Terminals |
| 1021 | Diagram and rating plate |
| 1022 | Air Vent |
| 1023 | Explosion Vent |
| 1024 | 100 mm dia thermo meter with thermometer pocket |
| 1025 | Four bi directional plain roller |
| 1026 | Buchholz relay |
| 1027 | Resistance Temp detector |
| 1028 | Marshalling box |
| 1029 | Automatic Voltage Regulator ( AVR) |
| 1030 | Remote Tap Changing controller ( RTCC) |
| 1031 | Transformer 11000/415 volts with on load Tap changer -15% to +5% in steps of 1.25% with RTCC, AVR and marshalling box and other specification as per BIS Level-2 |
| 1032 | 315 KVA |
| 1033 | supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 3C x 240 Sqmm, 11KV XLPE |
| 1034 | Supplying of 11 KV grade aluminium conductor, cross linked polyethylene (XLPE) insulated individual core screened, flat steel/strip armoured PVC sheathed cable complete as required. 3C x 185 Sqmm, 11 KV XLPE |
| 1035 | Laying of one number additional PILCA / PVCinsulated and PVC sheathed / XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV of size exceeding 120 sqmm but not exceeding 400 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning protective covering and refilling the trench etc. as required. |
| 1036 | Supply& Laying of following sizes of 1.1KV grade Copper conductor XLPE insulated and FRLS PVC sheathed armoured control cable including termination conforming torelevant IS. |
| 1037 | 4 core,2.5 sq.mm. |
| 1038 | 10 core,2.5 sq.mm. |
| 1039 | 12 core,2.5 sq.mm. |
| 1040 | Supply & Fixing of Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006. |
| 1041 | Supplying and Laying of Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006 etc. as reqd. |
| 1042 | Supplying & Placing of First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963 etc as reqd. |
| 1043 | Supplying & Installation of Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English) etc. as reqd |
| 1044 | EXTERNAL LIGHTING |
| 1045 | S.I.T.C of Following rating LED Street Lighting luminare with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole / pipe for supply voltage 100-270 AC 50Hz Luminare shall be confirm to IS :10322 part 5/ section-3 and shall be complete with all nessessary accessories as required. 60W LED Street Light |
| 1046 | S.I.T.C of Following rating LED Post Top lamp made in die cast aluminium housing with decorative clear / opel acrylic diffuser on existing pipe including connection with 1.5sq.mm coppwr conductor etc all complete as required. 20/25W LED Post top lamp clear |
| 1047 | S.I.T.C of Following rating approved make LED Bpllard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, conferming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.) |
| 1048 | Supplying& installation of 7 mtr. Height Octagonal Hot Dip galvanized pole (BOP. 7030) with top dia 70 mm bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12 mm (LxBxT) including suitable size of foundation bolt all complete as required (without Arm). |
| 1049 | 1m Single Arm Suitable for 70MM Top |
| 1050 | HVAC |
| 1051 | AIR COOLDED VARIABLE REFRIGERANT VOLUME/FLOW AIR CONDITIONING SYSTEM |
| 1052 | Supply, Installation, testingand commissioning of air cooled Variable Refrigerant Volume/Flow modular type air-conditioning system Invertor Controlled with step less modulation complete with indoor and outdoor units, individual remote controller and centralized controller, interconnected refrigerant piping ,full charge of refrigerant gas & oil, control cabling etc.as per detail given in specifications and having following items: Refrigerant to be used shall be - R - 410 A. |
| 1053 | OUTDOOR UNIT |
| 1054 | Supply, Installation, testingand commissioningof Both Cooling & Heating Modular type outdoor units suitable to operate at 415 ± 10 % volt, 50 Hz, 3 phase AC supply and suitable for cooling application by using 100 % inverter drivencapacity control compressors (Hermetically sealed scroll/Twin Rotary type) with stepless modulation complete with special acryl precoated heat exchanger, low noise condenser fan , auto check function for connection error in display panel, auto address settingas per specifications. TheCOP at AHRI conditions shall not be less than 4.2 . The units shall be complete with necessary mounting frames and capacity as mentioned below and as per specification. |
| 1055 | The cost should include the following : |
| 1056 | Nitrogen pressure testing for refrigerant pipe leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts. Refrigerant gas & oil charging as per OEM standard. |
| 1057 | Necessary corrosive treatment of copper coil of the ODU with Aluminum hydroxide, 25 microns thickness or equivalent coating as per manufacturer standard to protect from corrosion, sulfur and other chemical contaminants present in the air. The coating should be done in the presence of OEM representative.The coating shall be carried-out by the authorized applicator of coating manufacturer. |
| 1058 | Note : The ODU provided with cowl duct for exhaust air should have minimum 5 mm ESP. GI wire mesh (minimum 16 SWG thickness)type bird screen with framing at the Mouth of exhaust air Cowl duct of Outdoor Units. |
| 1059 | ODU Units Mounted on MS Frame/Masonry Pedestal with required anti-vibration mounting. |
| 1060 | 24 HP (2x12 HP) |
| 1061 | 28 HP (2x14HP) |
| 1062 | 36 HP (2x18HP) |
| 1063 | CEILING SUSPENDED DUCTED TYPE UNITS |
| 1064 | Supply,installation,testingandcommissioningoffollowing minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equippedwith washable synthetic mediapre-filter, fan section with low noise fan/dynamicallybalancedblower,multispeedmotor,coilsection with DX copper coil,electronic expansionvalve, cordedremote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ±10%,50Hzcompleteasrequired.Theunitshallhaveautomatic forceshutdownprovisionincaseoffireonreceiveingsignalfrom BMS System.The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. |
| 1065 | Indoor Units powder coated MS Hanging arrangement/wall Brackets/Spring Isolators with required anti-vibration mounting and Fire Rated Flexible Connection. |
| 1066 | Mid Static Ductable units (minimum 50 pascal external static pressure) |
| 1067 | 1.1 TR (375 CFM) |
| 1068 | 1.3 TR (450 CFM) |
| 1069 | 1.6 TR (600 CFM) |
| 1070 | Mid Static Ductable units (minimum 100 pascal external static pressure) |
| 1071 | 2.0 TR (725 CFM) |
| 1072 | 2.6 TR (875 CFM) |
| 1073 | 3.4 TR (1050 CFM) |
| 1074 | High Static Ductable units (minimum 150 pascal external static pressure) |
| 1075 | 4.0 TR (1400 CFM) |
| 1076 | 4.6 TR (1650 CFM) |
| 1077 | 5.5 TR (2050 CFM) |
| 1078 | 7.1 TR (2350 CFM) |
| 1079 | Refrigerant Joints and Headers |
| 1080 | Supply, Installation, Testing and Commissioning of copper Y-Joints sets, distributer and headers, suitable for various sizes of gas and liquid line of VRF System complete as required for the above system. |
| 1081 | Supply, Installation, testingand commissioningof self diagnostic type Corded/Cordless remote controllers for operation of indoor units. |
| 1082 | Supply, Installation, testing & commissioning of Main intelligent central controller with Scheduled Timer system Touch screen Type suitable for groups of indoorunits to operate, monitor, on/off, cyclic operation setting, temperature setting etc. The CRC shall be provided with suitable size metallic box with lock arrangement. |
| 1083 | Air Cooled Inverter Ductable Unit |
| 1084 | Supplying, installing, testing and commissioning of Air Cooled Ducted Air conditioners suitable for R410A or eco-friendly refrigerant with evaporating unit comprising of cooling coil, blower with motor in Metallic (Steel) casing and condensing unit comprising hermetically sealed scroll compressor, condenser coil, and propeller fan. Unit shall be complete with controls, interconnecting copper refrigerant piping with insulation, Expension kit to connect with DX AHU, and electrical cabling etc. between evaporative and condensing unit, refrigerant gas and oil and complete as per specifications. The unit shall be suitable for operating on 240 volt, 1 phase, 50 Hz AC supply with five star energy rating. The units shall be suitable for chorded remote operation. The refrigerant piping & cabling shall run in PVC sleeve Steel supporting structure for outdoor units suitable for wall mounting / floor mounting. |
| 1085 | Providing, fixing and testing of copper refrigerant piping of appropriate sizes duly insulated with nitrile rubber insulation of 19 mm thickness. The pipes plus nitrile rubber insulation and cable are to be covered with PVC flexible conduits for protection. |
| 1086 | Note: Providing and fixing of Powder coated M.S. angle iron frame work/Masonary Pedastal with required anti-vibration mounting for outdoor unitis also included in the above scope. Contractor to submit design/Scheme for Iron frame and obtain approval of engineer/employer before proceeding purchase & installation. |
| 1087 | Nitrogen pressure testing for refrigerant pipe leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts. Refrigerant gas & oil charging as per OEM standard. |
| 1088 | Necessary corrosive treatment of copper coil of the ODU with Aluminium hydroxide, 25 microns thickness or equivalent coating as per manufacturer standard to protect from corrosion, sulfur and other chemical contaminants present in the air. The coating should be done in the presence of OEM represantative.The coating shall be carried-out by the authorized applicator of coating manufacturer. |
| 1089 | 8.5 TRDuctable Split Unit -Only Condensing |
| 1090 | 11.0 TRDuctable Split Unit -Only Condensing |
| 1091 | Notes: The vendor may offer the outdoor units as per availability from the manufacturer, however keeping the tonnage same as per BOQ subject to approval by Consultant/Client. |
| 1092 | The indoor unitscapacity can be also as per availability from the manufacturer but keeping the minimum capacity as required in BOQ subject to approval by Consultant/Client. |
| 1093 | DOUBLE SKIN FLOOR MOUNTED AIR HANDLING UNIT WITH HEPA FILTER |
| 1094 | Supply, Installation, Testing and commissioning of factory built floor mounted Direct Expension (DX) double skin type horizontal/vertical air handling units made of 50±1 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine of density, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/ PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 8 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for variable frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation, 150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification. |
| 1095 | The coolingcoil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven syntheticmediaof10 micronparticlesizewith an efficiencyof90% in both the supply & exhaust side of AHU, fine filter section with filters of non woven syntheticmediaof5micron particle size in supply after fan, (Hepa filters shall be at terminals along with laminar flow plenum & not to be included in the cost), mixing chambercomplete with motor, beltdrive etc. withoutface and bypass dampers. TheAHU shall be accoustically insulated with 25mm thick open cell nitrile rubber & 36 Kg/m³ density PU foam & shall have thermal break. Themotor & blower assembly shallbemountedonAluminium extruded section with starter panel. These AHUs shall have air inlet / outlet connectionmadeofaluminium20 G & all fixing arrangement / blank off shall be of SS,thecomplete AHUshall conform to standard specification. Thefacevelocity across cooling coil shall be limited to 500 FPM (2.52 MPS) maxm & Fan outlet velocity shall be not exceed 9.0 m/s. |
| 1096 | Casing shall be of panel construction; double wall type packed with pressure injected CFC free foam insulation minimum 50mm ± 1mm thick. Casing framework shall be of modular galvanized iron, aluminium or Approved equal pentapost double skin construction. Outer skin shall be minimum 1.0 mm galvanized steel sheet while inner skin shall be minimum 1.2 mm galvanized steel sheet. The sheets should have a minimum galvanisation of 275 GSM. The outer skin and inner skin should be precoated or powder coated on the exposed side |
| 1097 | AHU shall be Eurovent certified. The mechanical performance of AHU shall be as per EN 1886. Rating performance for units, components and section shall be as per EN 13053. Fans shall be AMCA certified for |
| 1098 | Static pressure and Motor Rating : TheIndicated static pressure and motor rating is only provisional. Vendor to calculate static pressure based on drawings and pressure drop of finalized Equipment and submit for approval. The procurement shall be processed only after duly approval of calculation and selection from the Project Manager. |
| 1099 | Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor. |
| 1100 | 2500 CFM Supply Air, 8 Row CC, 125 mm St. Pr., For Supply Fan, Supply Fan, 800 CFM Ex. AirBlower, 40 mm St. Pr. for Exhaust fan with other accessories as specified) |
| 1101 | 3000 CFM Supply Air, 8 Row CC,125 mm St. Pr., For Supply Fan, Supply Fan, 1200 CFM Ex. AirBlower, 40 mm St. Pr. for Exhaust fan with other accessories as specified) |
| 1102 | DOUBLE SKIN CEILING SUSPENDED AHU |
| 1103 | Supply,installation,testingandcommissioningof factoryfabricatedDoubleSkinned Direct Expension (DX) Air- handling unit ceiling suspended type fabricated out of extruded aluminium section with 0.8mm pre-plasticized/ pre-coated Galvanised steel sheet outside & 0.8mm plain Galvanised steel sheet inside with blower, blower sectionandblowermotorTEFCtypesuitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 Rowcoolingcoil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven syntheticmediaof10 micronparticlesizewith an efficiencyof90%, polished stainless steel drain pan madeoutof 22 G sheet duly insulated complete with motor, direct / beltdriveas mentioned below etc. withoutface and bypass dampers. All direct driven fan motor shall be sourced from fan manufacturer & factory fitted only. TheAHU panelsshall be insulated with 23mm thick & 36 Kg/m³ density PU foam. Themotor & blower assembly shallbemountedonAluminium extruded sectiononly with starter panel. The complete AHUshall conform to standard specification. |
| 1104 | The coolingcoil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven syntheticmediaof10 micronparticlesizewith an efficiencyof90%,complete with motor, beltdrive etc. withoutface and bypass dampers. TheAHU shall be accoustically insulated with 25mm thick open cell nitrile rubber with 20 G perforated Galvanised steel sheet & 36 Kg/m³ density PU foam & shall have thermal break. Themotor & blower assembly shallbemountedonAluminium extruded section with starter panel. The complete AHUshall conform to standard specification. Thefacevelocity across cooling coil shall be limited to 500 FPM (2.52 MPS) maxm & Fan outlet velocity shall be not exceed 9.0 m/s. |
| 1105 | Casing shall be of panel construction; double wall type packed with pressure injected CFC free foam insulation minimum 50mm ± 1mm thick. Casing framework shall be of modular galvanized iron, aluminium or Approved equal pentapost double skin construction. Outer skin shall be minimum 1.0 mm galvanized steel sheet while inner skin shall be minimum 1.2 mm galvanized steel sheet. The sheets should have a minimum galvanisation of 275 GSM. The outer skin and inner skin should be precoated or powder coated on the exposed side |
| 1106 | AHU shall be Eurovent certified. The mechanical performance of AHU shall be as per EN 1886. Rating performance for units, components and section shall be as per EN 13053. Fans shall be AMCA certified for |
| 1107 | Static pressure and Motor Rating : TheIndicated static pressure and motor rating is only provisional. Vendor to calculate static pressure based on drawings and pressure drop of finalized Equipment and submit for approval. The procurement shall be processed only after duly approval of calculation and selection from the Project Manager. |
| 1108 | Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor. |
| 1109 | 3,000 CFM (6.0 TR), 50 mm St. Pr., 4 Row CC |
| 1110 | Supply, Installation, Testing and Commissioning of Normal Ductable/VRV Kits for AHUs having all controllers & Electronic Expansion Valve (EEV) and temperature set arrangement. It Shall have cut off arrangement after a particular set value of Supply air Temperature.AHU Kits & Controllers |
| 1111 | THERMOSTAT FOR AHU |
| 1112 | Supply, installation,testingandcommissioningof digital display typethermostat for air handling unitfor cool / heat application suitable for four pipe system & humidistat suitable for working with humidifier and hot water coil control valves for various air handling Units.Controller have provision to display differential pressure accress OT if required. The thermostat shall have provision of setting of space temperature and display of the same. |
| 1113 | The humidistat shall have provision of setting space RH and display of the same. The quoted price of thermostat / humidistat shall include the cost of 20mm MS conduits, control cabling, MS Box etc as required. The cost quoted shall be excluding the control valves and humidifier Cooling / heating thermostat |
| 1114 | Supply, installation,testingandcommissioningof Humidificationpackagewithall necessary controls asrequiredas perstandardspecification & of following capacities: |
| 1115 | 3.0 KW |
| 1116 | 4.5 KW |
| 1117 | Supply, installation & testing of factory fabricated Laminar air flow pattern perforated plenum made of 16 G aluminium sheet with hepa filters & suitable for operation theatre with allaccessories as required to suit, site condition as per specifications. |
| 1118 | SIZE-2.4mx2.7m |
| 1119 | SIZE-2.4mx2.4m |
| 1120 | AIR COOLED DX TYPE SPLIT ACUNITS |
| 1121 | Supply , installation, testing & Commissioning of ceiling suspended DX type split AC units with air cooled condenser complete with 5 Star Inverter type scroll/rotary compressor ,condenser ,wiring & accessories . Indoor units shall be ceiling suspended/wall mounted type complete with evaporator ,fan, filter ,drier, expansion devices & microprocessor control panel along with all accessories with refrigerant & oil charge ,corded remote controls. The unit shall be suitable for working at 240 ± 10%,50 Hz,1 phase AC supply .The unit shall be designed to take care of minimum vertical head 5mt & horizontal length of 30 mt & necessary oil separator shall be included ,Necessary supporting arrangement for both indoor & outdoor units ( Powder Coated /Epoxy paintedMS stand for ODU units as per approved make, shade by Architect) with necessary vibration isolation arrangement as per site condition etc. (without condensate drain pipe ,electrical power & control cabling between indoor & outdoor unit which shall be paid separately ). |
| 1122 | The coil in the outdoor units shall be provided with anti corrosive treatment. Necessary corrosive treatment of copper coil of the ODU with Blygold PoluAl (Aluminum hydroxide, 25-microns thickness) to protect from corrosion, sulfur and other chemical contaminants present in the air. Coating should be done in presence of OEM representative. The coating shall be carried-out by the authorized applicator of coating manufacturer. |
| 1123 | The Outdoor unit Compressor must be provided with 5 Year Warranty Period. |
| 1124 | Silver Ion Filter, Dust Filter |
| 1125 | Civil Work such as wall hole making , wall chiseling ,refilling of chiseling part with mortar etc. as per site condition. |
| 1126 | Nitrogen pressure testing for leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts |
| 1127 | Removable Covers for all indoor & Outdoor units shall be supplied & put on the units after installation & commissioning. |
| 1128 | Incoming power supply shall be provided near each indoor units |
| 1129 | 1.5 TR |
| 1130 | SCHEDULED TIMER FOR SPLIT AC |
| 1131 | Supply, installation, testing and commissioning of Scheduled Timer for wall mounted split type Air conditioning units. |
| 1132 | REFRIGERANT/DRAIN PIPING & CONTROL WIRING |
| 1133 | Supplying, installing, testing and commissioning of Shielded control cum transmission wiring of 2 core x 1.5 sqmm copper FRLSH, XLPE insulated cable in suitable GI conduits accessories between indoor and outdoor units. Necessary securing of conduit shall be made by contractor. After completion of work wall and floor shall be repaired and brought to its original finish. The rate will also include cost of laying of GI conduit between indoor and outdoor units. |
| 1134 | 2C x 1.5 Sq mm (Shielded-Unarmored) |
| 1135 | Supply, fixing, testing and commissioning of interconnecting soft/hard drawn copper refrigerant pipe work of following outer diameter duly insulated with fire rated class"O" closed cell elastomeric nitrile rubber type tubular insulation (19mm/13mm thick) between indoor & outdoor units & protected with 28 G aluminium sheet cladding as per specifications. All piping should be laid on Galvanized/Powder Coated tray supported by Galvanized M S Hangers & Clamps andallexternal pipingshall run in covered cable trays. The rateincludes all theitems required to complete the piping work and nothing extra should be payable except the cable tray. |
| 1136 | Vaccumiazation & Nitrogen pressure testing for leakages & flushing during installation & after commissioning between IDU & ODU. |
| 1137 | Civil Work such as wall hole making , wall chiseling ,refilling of chiseling part with mortar etc. as per site condition. |
| 1138 | 6.4 mm outer dia Soft Drawn with Tube Thickness-1.2mm( Insulation-19 mm ) |
| 1139 | 9.5 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm ) |
| 1140 | 12.7 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm ) |
| 1141 | 15.9 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm ) |
| 1142 | 19.1 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm ) |
| 1143 | 22.2 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm ) |
| 1144 | 25.4 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm ) |
| 1145 | 28.6 mm outer dia Hard Drawn with Tube Thickness-1.2mm( Insulation-19 mm ) |
| 1146 | 31.8 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm ) |
| 1147 | 34.9 mm outer dia Hard Drawn with Tube Thickness-1.62mm ( Insulation-19 mm ) |
| 1148 | 38.1 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm ) |
| 1149 | 41.3 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm ) |
| 1150 | Providing and fixing of cPVC drain water piping complete with fittings, flexible connection to IDU, necessary support as per specification and insulated with 6 mmthickfire rated class"O" closedcellelastomeric nitrile rubberinsulation. |
| 1151 | 25 mm dia |
| 1152 | 32 mm dia |
| 1153 | 40 mm dia |
| 1154 | VENTILATION FANS EQUIPMENTS |
| 1155 | SMOKE EXTRACTION/EXHAUST FAN |
| 1156 | Supplying, installation, testing and commissioning of AMCA Certified (For Air and Sound Performance) ceiling hung exhaust airtube axial flow fans of following capacity with GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor should be of high efficiency class IE3 (as per IS 12615) suitable for 3 Phase 50 Hz 415V ± 10 %, of class "H" insulation etc. including all accessories complete as required and as per specifications. Motor shall be of high temperature resistance "Class H Smoke Spill" 250° C for 2 hrs. Motor make shall be same as mentioned on the fire certificate. Fan total efficiency should not be less than 70%, noise level should not be more than 78 db. @ 3 m distance when measured in hemispherical reverberant room conditions. All the fans shall be hot dip galvanized with minimum 220 GSM Zinc Coating. Entire fan model & AMCA Seal shall appear in technical submittal of fan. Air moving capacity shall be as follows: |
| 1157 | Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor. |
| 1158 | Fan shall be supplied with Spring Isolators, Fire Rated Flexible Connection,GI gravity louvers, bird screen and fan guard. |
| 1159 | Note: Contractor Has to take approval on computer generated selection charts and fan curves showing power input and fan motor etc. prior to order thefans,(a) Noise level @ 3m from Fan shall be not more than 78 dB. |
| 1160 | Back draftDamper : Where required for system design roof-mounted fan shall be equipped with a rattle-free back draft damper to prevent air from re entering the fan when fan is not in operation, thus sealing completely in closed position. Damper shall be chatter proof under all conditions. |
| 1161 | Note:-These fans would be connected to the fire alarm system & BMS system of the building and would start automatically in case of Fire |
| 1162 | Note1. Outlet Velocity for normal mode fans not to exceed 10.0 MPS(Meter/Second) |
| 1163 | 2. Outlet Velocity for Fire mode fans not to exceed 12.0 MPS (Meter/Second) |
| 1164 | 3. Fan motor shall meet IE3 or above standard as per IS-12615 |
| 1165 | 4.Static pressure and Motor Rating : TheIndicated static pressure and motor rating is only provisional. Vendor to calculate static pressure based on drawings and pressure drop of finalized Equipment and submit for approval. The procurement shall be processed only after duly approval of calculation and selection from the Project Manager. |
| 1166 | 5. Thickness of casing : for dia( 315-630 )mm - 2mm , dia ( 710-1120)mm - 3mm , dia (1250-1400)mm - 4mm & dia 1600mm - 5mm. |
| 1167 | 6. In case of attenuator , calculation of reduction of sound level with insertion loss of attenuator is to be submitted. |
| 1168 | 2000 CFM (3400 CMH) at 25 mm static pressure |
| 1169 | 3000 CFM (5100 CMH) at 25 mm static pressure- |
| 1170 | 4000 CFM (6800 CMH) at 25 mm static pressure |
| 1171 | 12000 CFM (20400 CMH) at 25 mm static pressure- |
| 1172 | AXIAL FLOW FANS (SUPPLY/PRESSURISATION FAN) |
| 1173 | Supplying, installation, testing and commissioning of AMCA Certified (For Air and Sound Performance) ceiling hung Supply/ Pressurisationtube axial flow fans of following capacity with GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor should be of high efficiency class IE3 (as per IS 12615) suitable for 3 Phase 50 Hz 415V ± 10 %, of class "F" insulation etc. including all accessories complete as required and as per specifications. . Motor make shall be same as mentioned on the fire certificate. Fan total efficiency should not be less than 70%, noise level should not be more than 78 db. @ 3 m distance when measured in hemispherical reverberant room conditions. All the fans shall be hot dip galvanized with minimum 220 GSM Zinc Coating. Entire fan model & AMCA Seal shall appear in technical submittal of fan. Air moving capacity shall be as follows: |
| 1174 | Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor. |
| 1175 | Fan shall be supplied with Spring Isolators, Fire Rated Flexible Connection,GI gravity louvers, bird screen and fan guard. |
| 1176 | Back draftDamper : Where required for system design roof-mounted fan shall be equipped with a rattle-free back draft damper to prevent air from re entering the fan when fan is not in operation, thus sealing completely in closed position. Damper shall be chatter proof under all conditions. |
| 1177 | Note: Contractor Has to take approval on computer generated selection charts and fan curves showing power input and fan motor etc. prior to order thefans,(a) Noise level @ 3m from Fan shall be less than 78 dBA. with starter panel |
| 1178 | Note:-These fans would be connected to the fire alarm system & BMS System of the building and would start automatically in case of Fire |
| 1179 | Note1. Outlet Velocity for normal mode fans not to exceed 10.0 MPS(Meter/Second) |
| 1180 | 2. Outlet Velocity for Fire mode fans not to exceed 12.0 MPS (Meter/Second) |
| 1181 | 3. Fan motor shall meet IE3 or above standard as per IS-12615 |
| 1182 | 4.Static pressure and Motor Rating : TheIndicated static pressure and motor rating is only provisional. Vendor to calculate static pressure based on drawings and pressure drop of finalized Equipment and submit for approval. The procurement shall be processed only after duly approval of calculation and selection from the Project Manager. |
| 1183 | 5. Thickness of casing : for dia( 315-630 )mm - 2mm , dia ( 710-1120)mm - 3mm , dia (1250-1400)mm - 4mm & dia 1600mm - 5mm. |
| 1184 | 6. In case of attenuator , calculation of reduction of sound level with insertion loss of attenuator is to be submitted. |
| 1185 | Supply Fan |
| 1186 | 2000 CFM (3400 CMH) at 25 mm static pressure |
| 1187 | 3000 CFM (5100 CMH) at 25 mm static pressure- |
| 1188 | 4000 CFM (6800 CMH) at 25 mm static pressure |
| 1189 | 12000 CFM (20400 CMH) at 25 mm static pressure- |
| 1190 | CABINET TYPE CENTRIFUGAL FAN : |
| 1191 | Supply, installation, testing, commissioning of direct driven double skin Cabinet type centrifugal fanwith 25mm thick PUF insulation fan section consist of Centrifugal Fan, forward curve, with radial tip double wheel, double inlet, consisting of motor, drive arrangement, aluminum common frame for fan and motor, cushy foot mounting, aluminum base frame for the unit, VCD on the outlet of fan, filter and accessories as per specification and drawing complete with 25mm thick five layer GI wire mesh filter,Structural frame with blank-off sheet, anchor fastener with vibration isolation Springs and starter panel. |
| 1192 | Motor: Fan motor shall be energy efficient and suitable for 415±10% volts, 50 cycles, 3 phase AC power supply, squirrel-cage, totally enclosed, fan-cooled motor, provided with class H insulation, and of approved make. Motor name plate horsepower shall exceed brake horsepower by a minimum of 10%. Motor shall be designed especially for quiet operation and motor speed shall not exceed 1440 rpm. The fan and motor combination selected for the required performance shall be of the most efficient (smallest horsepower), so that sound level is lowest. Motor shall have a minimum efficiency of IE3 or as per relevant BIS/NEMA codes. |
| 1193 | Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor. |
| 1194 | Fan and motor shall be fire rated to 250 Deg C for 2 hours or as indicated in the specifications |
| 1195 | The motor shall be spark-proof. The starter panel shall be provided with in-built timer to switch OFF the fan after a preset time (say 300 seconds) once triggered |
| 1196 | Note:-These fans would be connected to the fire alarm system/BMS System of the building and would start automatically in case of Fire |
| 1197 | Note1. Outlet Velocity for normal mode fans not to exceed 10.0 MPS(Meter/Second) |
| 1198 | 2. Outlet Velocity for Fire mode fans not to exceed 12.0 MPS (Meter/Second) |
| 1199 | Static pressure and Motor Rating : TheIndicated static pressure and motor rating is only provisional. Vendor to calculate static pressure based on drawings and pressure drop of finalized Equipment and submit for approval. The procurement shall be processed only after duly approval of calculation and selection from the Project Manager. |
| 1200 | 5000CFM with 35 mm static Pressure |
| 1201 | INLINE FAN (Ceiling suspended) |
| 1202 | Supply, installation, testing, commissioning of Inline fan with vibration isolators, speed regulator, GI gravity louvers,Bird Screen and required cable as per specification and drawing. The Motor shall be suitable to run on 1 phase/50 hz/ 220 v electrical power Supply including fireretardantnon-porousdoublelayerflexible connection of the following capacity. |
| 1203 | The louvers & bird screen shall be made of heavy gauge metallic construction. |
| 1204 | 200 CFM (340 CMH) at 10 mm static pressure |
| 1205 | 300 CFM (510 CMH) at 10 mm static pressure |
| 1206 | 400 CFM (680 CMH) at 10 mm static pressure |
| 1207 | 500 CFM (850 CMH) at 12 mm static pressure |
| 1208 | 600 CFM (1020 CMH) at 12 mm static pressure |
| 1209 | 1000 CFM (1700 CMH) at 15 mm static pressure |
| 1210 | PROPELLER FAN |
| 1211 | Supply, installation, testing and commissioning of wall mounted Propeller type heavy duty exhaust Fan of metallic construction complete with speed regulator, bird screen, gravity louvers, vibration isolators, required cable, plug & other accessories compete as required, suitable for single phase, 240± 10 volts, 50Hz AC. supply of following capacities: The louvers & bird screen shall be made of heavy gauge metallic construction. 300 mm sweep dia (900 RPM) |
| 1212 | Supply, installation, testing & commissioning of Wall mounted Propeller type exhaust air fans of high grade ABS plasticconstruction complete with electric motor suitable for operation on 230 V+ 10%,50 Hz, 1 phase AC supply fitted with speed regulator, mountings frames, louvers and bird screen, required cable & plug to connect with socket etc. complete as required of following capacities. 250 mm sweep dia |
| 1213 | AIR DISTRIBUTION WORKS (DUCTING,INSULATION,DAMPER, GRILLE & DIFFUSER) |
| 1214 | FACTORY FABRICATED GALVANIZED STEE(GSS) SHEET METAL DUCTS |
| 1215 | Supply, installation, testing and commissioning of factory fabricated Galvanized Steel (GSS) Sheet metal ducts complete with flanges, neoprene rubber gasket, elbows, SplitterDamper,vanes, hangers & support etc. as required as per IS/DW144/SAMACNA standard & confirming to specification. Duct shall be furnish at sitein "L" shape or box shape from factory. The rates shall include all materials of the duct and labour for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications. |
| 1216 | Note :Splitter Shall be a part of ducting. |
| 1217 | 0.63 MM (24 Gauge ) |
| 1218 | 0.80 MM (22 Gauge ) |
| 1219 | 1.00 MM (20 Gauge ) |
| 1220 | 1.25 MM (18 Gauge) Plenum |
| 1221 | SITE FABRICATED GALVANIZED STEE(GSS) SHEET METAL DUCTS |
| 1222 | Supply, Fabrication, installation and testing of Galvanized Steel (GS) sheet metal ducts & finally applying fire rated paint as per BS 476 Part 24(SiteFABRICATED DUCTS For Connection /Plenum etc.) in accordance with the approved shop drawings complete with all accessories like vanes, flanges, suspension rods , anchor bolts, GI bolts & nuts, etc., as per specifications. |
| 1223 | Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 |
| 1224 | 0.63 MM (24 Gauge ) |
| 1225 | 0.80 MM (22 Gauge ) |
| 1226 | 1.00 MM (20 Gauge ) |
| 1227 | 1.25 MM (18 Gauge) |
| 1228 | FIRE RATED FACTORY FABRICATED GALVANIZED STEE(GSS) SHEET METAL DUCTS |
| 1229 | Supply. Installation, testing and commissioning of Fire rated sheet metal ducts shall be fabricated from Lock Forming Quality grade prime galvanized steel sheet with flanges complete with supports, vanes, dampers, links, levers and quadrants etc. as per specifications and drawings. Supporting distance shall not exceed 1.2 Mtr with 6mm thick fire retardant gasket suitable for 250 deg C 2 hr shall be used in duct joints along with fire sealants. Suitable access doors shall be provided at every 3m.Duct shall be furnish at sitein "L" shape or box shape from factory. The rates shall include all materials of the duct and labor for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications. |
| 1230 | All fire rated duct, smoke exhaust ducts shall be quoted with flame bar BWII or equivalent to achieve the required fire rating, also all the related accessories gaskets shall be suitable for the required fire rating. |
| 1231 | Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 |
| 1232 | 1.25 MM (18 Gauge) Plenum & Exhaust Duct |
| 1233 | ALUMINIUM (AL) DUCTING FOR OT |
| 1234 | Supply, installation, testing and commissioning of factory fabricated Aluminium Sheet metal ducts complete with flanges, neoprene rubber gasket, elbows, SplitterDamper,vanes, hangers & support etc. as required fot OT and as per IS/DW144/SAMACNA standard & confirming to specification. Duct shall be furnish at sitein "L" shape or box shape from factory. The rates shall include all materials of the duct and labour for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications. |
| 1235 | The joint between the ducts shall be done by means of polymer “flange / slide-in channel” system to prevent air leakages. Turning vanes, elbows and reducers to be considered as part of supply of ducts. Ducts shall be supported by cable supports / GI slotted channels with threaded rods. Internal Stiffeners shall be used to prevent bulging of ducts for the sizes above 800 mm. |
| 1236 | 0.80 MM (22 Gauge ) With 32mm Insulation |
| 1237 | 1.00 MM (20 Gauge ) With 32mm Insulation |
| 1238 | 1.25 MM (18 Gauge)With 32mm Insulation |
| 1239 | Duct Insulation |
| 1240 | Supplying , installation, testing & commissioning of external thermal insulation on ducts with Closed Cell Elastomeric Nitrile Rubber Insulation of density not less than 50±5 Kg/m³ & thermal Conductive not exceeding 0.032 W/mK at an average Temperature of 0°C and . The Material Shall be rated as Class 1as per BS476 Part7for surface spread of flame test and Class O as per BS476 part6 for fire propagation test. The Material shall have Fire Approval from CBRI - Roorkee & no toxicity under flaming and non- flaming condition as per AITM 3.000 (1993). Adhesive used for setting the insulation shall be non - flammable, Vapour Proof. All Joints should be sealed with 3 mm thick 50 mm wide PE tape and Flange to be overlapped by 6" width of the same material thickness. FinallyDuct insulated should be strapped by 12mm metallic Packingstrip at every random meter & conforming to standardand Specification. |
| 1241 | 19 mm |
| 1242 | 25 mm |
| 1243 | Duct Acoustic Lining |
| 1244 | Supply and fixing of acoustic lining of supply air duct and plenum withthick Engineered Nitrile Rubber open cell foam having a Noise Reduction Coefficient of 0.55 with Density 160 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7, Air Erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass Fungi Resistance Test as per DIN EN ISO 846 Method A and Bacterial Resistance Test as per DIN EN ISO 846 Method C; to be applied using manufacturer"s recommended Rubber based Adhesive in a blend of solvents. |
| 1245 | Acoustic lining in ducts/plenum up to 5.0 Running meter from Fan Outletas per specification and drawings. |
| 1246 | 20 mm For Duct |
| 1247 | 25 mm For Plenum |
| 1248 | CONTROL DAMPER |
| 1249 | VOLUME CONTROL DAMPER |
| 1250 | Supply,. Installation, testing and commissioning of 18 Gauge G.I construction Frame with 22/24 Gauge GI Aero foil blades Volume control Duct/Wall Dampers with linkages, levers & fittings for Controlling the Airflow in Ducts with neoprene rubber gaskets,nuts, Bolts, Screws Linkages, Flanges etc. as per specification. |
| 1251 | MOTRIZED VOLUME CONTROL DAMPER |
| 1252 | Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU room. |
| 1253 | Motorized (ON-OFF Type) duct mounted GI volume control damper |
| 1254 | Motorized (ON-OFF Type) duct mounted GI volume control Actuator |
| 1255 | Supply, Installation, testing and commissioning of 18 Gauge G.I construction Back draft Dampers for Controlling the recirculation of air with neoprene rubber gaskets,nuts, Bolts, Centrifugals Linkages, Flanges etc. as per specification. Louvres shall be made powder coated extruded aluminum. |
| 1256 | Supply,. Installation, testing and commissioning of 18 Gauge aluminum alloy extrusions with welded/cleated frames Pressure Relief Dampers for Controlling the Excess pressure up to 60pa with neoprene rubber gaskets,nuts, Bolts, Centrifugals Linkages, Flanges etc. as per specification. Louvres shall be made powder coated extruded aluminum with suitable thickness. |
| 1257 | Supply, installation, testing and commissioningof 50 micron Powder coated Aluminum extruded Air Terminal (Diffuser/Grille) asper specification & and drawings including fixing frames of GI in False ceiling/wall. |
| 1258 | Supply. Installation, testing and commissioning of powder coated extruded aluminium section grills with aluminium dampers for supply air terminal and grilles without damper for return air for air-conditioningas per specification. |
| 1259 | Grilles with Dampers |
| 1260 | Grilles without Dampers |
| 1261 | Supply. Installation, testing and commissioning of powder coated extruded aluminium square diffusers with antismudge ring and removable core. |
| 1262 | Supply air with dampers |
| 1263 | Return air without damper |
| 1264 | Supply. Installation, testing and commissioning of thermal flexible aluminum duct of following sizes duly supported at regular interval as per site requirement & spefications. 200 mm |
| 1265 | Supply. Installation, testing and commissioning of slot diffusers with/without damper as specified below and as per specification. |
| 1266 | 3-Slot Diffuser |
| 1267 | 2-Slot Diffuser |
| 1268 | Supply. Installation, testing and commissioning of powder coated extruded aluminum Linear Grille. |
| 1269 | 100 mm |
| 1270 | 150 mm |
| 1271 | 200 mm |
| 1272 | Supply and fixing of non vision air transfer door grille of powder coated extruded aluminium, single deflection grille with horizontal vanes arrangement etc. as per specifications and drawings. |
| 1273 | Supply, Installation, Testing and Commissioning of Fresh Air/Exhaust air Louversminimum 80 mm deep comprising of inclined blade and extended-out lowest blade for disposal of rain water including the wire mesh, filter(washable type filter sectionClass-G3 having efficiency >80% down to 20 micron fitted in aluminium frame) . The louver shall be of extruded Aluminum construction, and powder coated to the approved finish and color. |
| 1274 | ISOLATOR FOR OUTDOOR UNIT |
| 1275 | Supply, Installation, Testing & Commissioning of following Switchgears as an Isolator in IP-65 rated in power coated 16 SWG sheet steel enclosure . |
| 1276 | 40A 4P MCCB(25 KA) |
| 1277 | 63A 4P MCCB(25 KA) |
| 1278 | POWER CABLING |
| 1279 | Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes : |
| 1280 | 4C x 16 Sq. mm Copper Conductor (Armoured) |
| 1281 | 4C x 10 Sq. mm Copper Conductor (Armoured) |
| 1282 | 4C x 6 Sq. mm Copper Conductor (Armoured) |
| 1283 | 4C x 4 Sq. mm Copper Conductor (Armoured) |
| 1284 | EARTHING STRIP/WIRES |
| 1285 | Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 1286 | Supply & laying 25x5mm GI strip at 0.5mt below ground as strip earth electrode including connection/terminating with GI nut,bolt,spring,washer etc. as required.) jointing shall be done by overlapping &with 2sets of brass nuts bolt spring washer spaced at 50mm).25mm x5mm |
| 1287 | HOSPITAL FURNITURE |
| 1288 | Supply, Installation / Fixing, Testing & Commissioning of Hospital Furniture complete with following as per technical specifications attached. |
| 1289 | Labour Delivery Bed Overall Dimension: 230 x 103 cms (L x W), Over All Length, with Leg Section Recessed: 175 cms, Height Adjustment (Motorised): 60 x 97 cms, Back Section Adjustment (Motorised): Upto 70 Deg, Trendelenburg Position (Motorised): Upto 15 Deg, Hand Held Remote Controller, operated by Patient, Attendant or Doctor for achieving the desired positions of the bed. Moulded Side Safety Railings, equipped with Pneumatic Pumps for smooth and jerkless movement. Provided with a pair of strong, moulded lithotomy pads (with straps), mounted on S.S. Stand. Push handle mounted on the sides for the patient’s ease. Strong built LDR Bed is mounted on four 12.5 cms swivel castors (Two with brake). Optional Upgrade: Central Locking Castors. Recess-able leg section with S.S. waste receptacle underneath, connected with a drain pipe. Provided with Mattress in three sections (removable for the leg section) |
| 1290 | Baby Bed Two sections, Uniformly perforated, CR M.S. sheet top. One smooth crank mechanism at foot end panel to obtain Head Raise. Tubular Head and Foot Panels mobile on 10 cms Castors (Two with brakes). Provided with Drop Down, tubular type side safety rails. Pretreated and electrostatic powder coated. Supplied in Knock Down Condition. Optional: I.V. Rod,Suitable Size Mattress (Optional) Overall Size Approx.: 140(L) x 75(W) x 60(H) cms |
| 1291 | Kick Bucket (SS) Stainless Steel Frame, Deep Container, all round bumper. Mounted on Three Ø 7.5cms swivel castors. Overall Size: Ø 34 x 34(H) cms. Container Capacity: 10 Litres |
| 1292 | Examination Light (LED) Illumination Intensity : 89000 Lux (D 30cm) 37000 Lux (D 50cm), Light Field Diameter: 4cm at distance 50cm, Light Source / Powerof LED: LED Bulbs 1x3W, No of LED : 1, Light Color Temp : 6000-6500 K, LED Average Life : 5000 Hours. Kind of Extension : 76cm adjustable goose arm, Power Supply: AC 110-240V 50/60 Hz. Brightness Control : Switch ON/OFF on the handle (Brightness Control on the Control Box), Power Cord : 300cm Length, Configuration : Mobile, Wall Mounted, Table Clamp and Rail Clamp |
| 1293 | Examination Couch (Pneumatic Back Rest) Fixed upholstered top 4" thick in two pieces. Headrest adjustable on gas spring. Upper section of box with three drawers. Lower section comprises of three cabinets with separate doors. B.P. apparatus tray provided near headrest. Pretreated and powder coated. Overall Approx. Size: 189(L) x 56(W) x 84(H) cms. |
| 1294 | Patient Trolley With Removable Stretcher Removable stretcher top on CR, ERW tubular steel trolley mobile on four 15 cms dia swivel castors, two with brakes. Provided with O cylinder carrier. Pretreated and powder epoxy finish. Two 2 locations for drip rod. Overall Size: 215(L) x 65(W) x 82(H) cms (without mattress). Stretcher Size: 182(L) x 55(W) cms (without handle). Supplied in Knock Down Condition. |
| 1295 | Wheel Chair Folding Type, Self Propelling, Pretreated & Epoxy Powder Coated Tubular Frame Work, Foldable Aluminum Foot Rests on the Fixed Leg Rests with Fixed, comfortable Arm Rests, Weight Carring Capacity 120 kg. (Approx). Front Swivel Castors of 20 cms. Rear Soild tyres of 60 cms, with Brakes, Strong Washable Seat & Back, Seat Width : 46 cm, Seat Depth : 45 cm |
| 1296 | ICU Bed having four function with high low, backrest & knee rest functions powered by means of three actuators. The fourth function of trendelenburg can be adjusted with manual crank. Overall Sizes (in mm): 2312L X 1060W X Adjustable from 490-770H Lying Surface: Sheet metal Lying surface of 1.2mm thickness. Lying surface area consists of mattress retainer to define the position of the mattress. Castors: High endurance Plastic injection molded castors with dual locking arrangement diagonally placed. Wheel Dia. 125mm & Stem dia is 22mm. Diagonal locking provides better stability to bed in locked position. Mattress: 4 Section Mattress 100mm thk for ICU Bed. FOAM Density: 40±2 kg/m3 & Hardness in Kg: 45±2 as per IS:7888 for 25% Compression. UPHOLSTRY Stitched Upholstry Cover Material: Helium Heavy A/F F/R SM |
| 1297 | Mattress for ICU Bed: 4 Section Mattress 100mm thk. FOAM Density: 40±2 kg/m3 & Hardness in Kg: 45±2 as per IS:7888 for 25% Compression. UPHOLSTRY Stitched Upholstry Cover Material: Helium Heavy A/F F/R SM with Fire Retardent and Antimicrobial Properties |
| 1298 | Fowler Bed- Overall Sizes-2268mm(L)x922 mm(W)x610 mm (H).A two function bed wich has n adjustable backrest and upperleg rest.Bed frame material is MS ERW Rect tube having sectional area 30mmx60 mm with thickness of 1.6mm .Lying surface frame is MS ERW round tube of dia 25.4 mm wiht thickness 1.6 mm.The head board/legboard frame is mS ERW Round tube of dia 25 mm and 31.75 mm respectively with thickness of 1.6 mm .The lead screw is EN8 with acme thread section of pitch thickness 6 mm.Handle is PPCO and lying surface is made up of CRCA of 1,m thickness.High endurance metal series castors sre provided with dual locking arrangements are diagonally placed.Provision for mosquioto net pole and IV pole holder.The finish is anti rust thermosetting epoxy polyster and powder coated parts in RAL white,plastic parts in cool grey 8C.Understructure stikers in pantone cool grey etc.Maximum patient load 135 kg,backrest elevations 70+/- 2 degree and knee rest elevation 24 +/-2 degree.The manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007. |
| 1299 | Mattress for Fowler Bed: 4 Section Mattress 75mm thk. FOAM Density: 40±2 kg/m3 & Hardness in Kg: 45±2 as per IS:7888 for 25% Compression. UPHOLSTRY Stitched Upholstry Cover Material: Helium Heavy A/F F/R SM with Fire Retardent and Antimicrobial Properties |
| 1300 | Semi Fowler Bed- Single Function bed which has an adjustable backrest and a fixed lower section. Overall Size in mm : 2268 (L) x 922 (W) x 610 (H) Material Specification : 1. Bed Frame made from (a) MS ERW Rect. Tube of section 30mm x 60mm and thickness 1.6 mm (b) MS ERW Round tube of section 30 mm x 30 mm and thickness 1.6 mm. 2. Laying Surface Frame made from MS ERW Round Tube of section Æ 25.4mm and thickness 1.6 mm. 3. Head Board/Leg Board Frame made from MS Round Tube of section Æ19, Æ25.4 & Æ31.75 mm and Thickness 1.6 mm with Higher diameter tube provides a studay understracture. 4. Lead Screw EN8 ACME 6 MM Pitch Thread Rolled En8 Lead Screw,with ACME thread and 6mm pitch gives good strrength, with ease of opreation. 5. Handle PPCO Snap Locking Handle lever with handle body keep it in folding position when not use. 6. Lying Surfaces CRCA 1.0 mm Laying Surface area consists of mattress ratainer to define the position of the mattress. 7. Castors High endurance metal series castor and provided with dual locking arrangement are diagonally placed wheel Dia 125mm & Stem dia is 22mm. Diagonal locking provides better s stability to bed in the locked position. 8. Mosquito Net Ple Holder: Privision for mounting of mosquito net pole. 9. IV Pole Holder: Provision for mounting of IV pole |
| 1301 | Mattress for Semi Fowler Bed : 2 Section Mattress 75mm thk. FOAM Density: 40±2 kg/m3 & Hardness in Kg: 45±2 as per IS:7888 for 25% Compression. UPHOLSTRY Stitched Upholstry Cover Material: Helium Heavy A/F F/R SM with Fire Retardent and Antimicrobial Properties |
| 1302 | Examination Table- Description The examination table is made of sturdy structure. The backrest has a ratchet mechanism for tilting the backrest. Overall Sizes L - 1830 mm x W. - 600 mm x H. - 850 mm Material Specifications 1. LegFrame - MSE.R.WTube 30x30 Thickness 1.6mm 2. Intermediate Frame - MS E.R.W Tube 30 x 30 Thickness 1.6mm 3. Leg Shoe Nylon 6 (To avoid wear and tear) 4. Lying surface - MSS. Sheet Thickness 1.2mm 5. Ratchet - M.S plate Thickness 5mm (Provides the bask rest tilt 0°, 15°, 30° adjustment positions. Finish Specifications 1. Powder coating Epoxy polyester. 2. Color RAL white, Plastic parts in Gray (Pantone cool gray 8C) Performance Specifications Maximum safe patient Load - 135 Kg. |
| 1303 | Mattress for Examination Table 30mm thk. FOAM Density: 40±2 kg/m3 & Hardness in Kg: 45±2 as per IS:7888 for 25% Compression.UPHOLSTRY Stitched Upholstry Cover Material: Helium Heavy A/F F/R SM with Fire Retardent and Antimicrobial Properties |
| 1304 | Hospital Sheet Bed- Overall Sizes: (L)2268 mm X ( W)922 mm X (H) 610 mm Description: Sheet Bed should be a plain bed used in the recovery ward. Material Specifications: Under Structure has a Higher diameter tubewhich should provide a sturdy understructure. Lying surface area of CRCA Finish Specifications: Head Board/Leg Board should be made of frame MS ERW RoundTube of sections Ø19, Ø25.4& Ø31.75mm, ofthickness1.6 mm Provision for mounting of IV Pole and Mosquito Net pole should be present Finish Specifications: Powder coating should be Bacteriostatic and thermosetting epoxy Polyester, formulated to fulfill the requirements for bacterial protection. All powder coated parts in RAL white Performance Specifications: Maximum patient load should be 135 kg |
| 1305 | Rexine Mattress- Thickness-Mattress: 3"+ SANDWITCHCONSTRUCTION: Round corners - YES Hitlon thickness ( MM): 60 Hitlondensity (Gm/dcm3): 23 Coir(Both side) ThicknessMM: 20 Density (Gm/dcm3): 70, DRC (%): 22 QUILTING - COMBINATION / LAYERS: Pilled Foam – Quilting (One Side) ThicknessMM - 14 Pilled Foam Density Gm/dcm3 - 18 PU foam / EPE sheet side walling ThicknessMM - 3 TOTAL MATTRESS THICKNESS-MM - 114 REXINE (GSM): 150 Guaranty period(Years): 1 Note: * Finish product thickness should be measure from outer to outer surface . Tolerance +5 mm |
| 1306 | Baby Crib on Stand- Crib arrangement on Bed having Overall Size L - 908 mm x W - 416 mm x H - 771 mm Material Specification MS E.R.W. Tube |
| 1307 | Mattress for Baby Crib 50mm thick. FOAM Density: 40±2 kg/m3 & Hardness in Kg: 45±2 as per IS:7888 for 25% Compression. UPHOLSTRY Stitched Upholstry Cover Material: Helium Heavy A/F F/R SM Color: Navy Blue (350 GSM, 0.45 THK) with Fire Retardent and Antimicrobial Properties |
| 1308 | Emergency Recovery Trolley- 1. The emergency trolley should be height adjustable, back rest should be adjustable and have tredelenburg and reverse trendelenburg functions. 2. Overall Size should be in-between L 2100 to L2200 X W (900)mm to W1000mm X (H) Adjustable from 700mm to 1080 mm 3. Bed Frame should be made of ERW 25X50 tube with thickness of 1.6 mm 4. Base frame should be made of ERW 25X50 tube with thickness 0f 1.6mm 5. The bed should have smooth Trendelenburg and reverse trendelenburg function with assist of 2 nos Gas Spring .the gas springs should be of 530 mm length and 168 mm stoke. 6. The bed frame should be height adjustable by assist of Hydraulic Pump stroke of 140mm.It should be smooth functioning and consistent motion during operations is required. 7. The trolley should be provided with detachable stretcher which should be have x-ray permeable top made of high pressure compact laminate of 6mm thick. The top should be exceptional chemical and stain resistance. The fixed portion of the top should be 1065 mm (L) x 590 mm (W) and tilted back portion should be 728 mm (l) x 590 mm (W). 8. There should be ms made x-ray cassette holder which can move along with the top length to perform x-ray on the different position. The x-ray Cassette should be top mounted. 9. Backrest should be adjustable on ratchet for patient comfort from 0 to 70 Degree 10. The trolley should be provided with high end 125 mm non marking Steinco castors which should be lockable diagonally. 11. The trolley should have Safe working Load should of 135 Kg on flat top . 12. There should iv pole holder with ht adjustable ss made telescopic iv pole with two hooks to mount saline bags. 13. The trolley should be provided with 8 mm dia ms zinc plating urine bag holder on both the side. 14. The trolley should be provided with drop down ss made side rails which should provide shelter in more than half of the total bed length. the tube should be of 19 mm dia and 1.2 mm thick ss 304 made. 15. The trolley should have 4 nos Neoprene made bumpers for Excellent Shock absorbing property. 16. The top frame should have X ray Tray assembly made of MS CRCA sheet 1.2 thick X ray Tray can slide along the stretcher length. Provision given for changing the X ray cassette at the leg side , knob to be provided for locking the assembly during TR operation .17. Fail Safe Mechanism- the trolley should have Fail Safe mechanism to avoid collapse of ERT during gas spring failure for TR & ATR Mechanism. 18. The trolley should be provided with 2 nos U shaped head and foot bow at both the end to drag or push the trolley for movement. the bow should be covered with neoprene material for better grip and avoid cold shock during patient handling. 19. MS Oxygen Cylinder Holder – Provision should be given to mount B type Oxygen Cylinder at the head side of trolley. 20. The trolley should have MS file holder at the bottom to carry file and other accessories during patient movement. 21. The trolley should be provided with two pair of patient safety belt . 22. The bed should be provided with 40 density 50 mm thick PU foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & X-ray permeable. The zip & stiches for the mattress cover should be concealed 23. All the MS parts should be treated with nine tank pre-treatment procedure with zinc phosphate and powder coated with antimicrobial and thermosetting epoxy polyester to control the bacterial growth. 24. The welding should be done by co2-argon welding and there should be Synerji coat on the welded areas to minimise early rusting. 22. The Manufacturer adheres to a certified quality management system in compliance with the following standards: a. ISO 9001:2008 b. ISO 14001:2004 c. OHSAS 18001:2007 d. CE certificate e. ISO 13485 |
| 1309 | Examination Bed- Examination Table of Overall Sizes (L)1957mm x (W)625mm x (H)808mm having gas-lift assisted head rest with continuous adjustment from 0° to 30°. The design focuses on ease of operation, hygiene, doctor and patient ergonomics, and aesthetics. Homogeneous soft forms with rounded edges evoke feeling of comfort and safety. Material Specification -Mattress and Up-holstery is made with PU molded foam with density 50-55, of 625mm x 65mm section, of 23 mm thickness. Mattress is projecting out from the understructure to provide soft touch from all sides. Seamless upholstery is provided to avoid spread of bacteria. Head Rest is made of PU molded foam with density 50-55, Section is made of 625mm x 65 mm.Thickness is 23mm. Gas-lift assisted head rest with continuous adjustment from 0° to 30°. UnderStructure and top frame is made of ERW square tube , os section 30mm X 30mm and 1.6 mm. Understructure is made of MS square tubes with unique styling that provides better strength and stability. It is provided to reduce visual clutter and offers better access and reach."Top Drawer Unit is provided, made of CRCA sheet construction with SS handle & SS hinge. Sheet thickness 1.2 ,0.8 and 0.6. Two drawers at top;each of volume 510 x 334 x 95 mm are provided". "BP Apparatus tray: CRCA sheet construction with SS handle and SS hinge Dia 10 for handle. Sheet thickness 1.2 ,0.8 and 0.6. swivel tray is designed for BP Apparatus that can be concealed when not in use. SS Handle: SS 202 Dia 10 - Aesthetically designed handles are placed in such a way that gives a unique look also provide wider space for griping to users. "Ergonomics: Increased width of the table (625mm) gives better comfort for patients. Optimized height (808mm) of the table for comfortable observation and reach. Tapered shape is provided to give a unique look and better access for doctor. L-shape leg is provided for better stability." Single Step stool is made ofERW square tube. Textured and Rubber mat is provided, of 20mm X 20mm size. Tube 1.2 mm thick and mat 3.0 mm thick Size:485(L) x 335 (W) X 210 (H) Step stool is made of MS square tubes, is strong and firm. Top is made of textured rubber offering firm grip for climbing. Tissue roll Holder SS304 , made of ERW TUBE Ø12.7 mm and1.2 thk, isused to mount Tissue roll. Finish Specification - Powder coating is Bacteriostatic and thermosetting epoxy polyester,formulated to fulfill the requirements for bacterial protection. Performance Specification - Maximum patient load is 135 kg. Head Rest is adjustable 0 - 30°.BP Apparatus tray is provided to Swivel angle 0 to 180 deg. Approx. |
| 1310 | Examination Couch Gyenac - Examination Table of Overall Sizes (L)1957mm x (W)625mm x (H)808mm having gas-lift assisted head rest with continuous adjustment from 0° to 30°. The design focuses on ease of operation, hygiene, doctor and patient ergonomics, and aesthetics. Homogeneous soft forms with rounded edges evoke feeling of comfort and safety. Material Specification -Mattress and Up-holstery is made with PU molded foam with density 50-55, of 625mm x 65mm section, of 23 mm thickness. Mattress is projecting out from the understructure to provide soft touch from all sides. Seamless upholstery is provided to avoid spread of bacteria. Head Rest is made of PU molded foam with density 50-55, Section is made of 625mm x 65 mm.Thickness is 23mm. Gas-lift assisted head rest with continuous adjustment from 0° to 30°. UnderStructure and top frame is made of ERW square tube , os section 30mm X 30mm and 1.6 mm. Understructure is made of MS square tubes with unique styling that provides better strength and stability. It is provided to reduce visual clutter and offers better access and reach."Top Drawer Unit is provided, made of CRCA sheet construction with SS handle & SS hinge. Sheet thickness 1.2 ,0.8 and 0.6. Two drawers at top;each of volume 510 x 334 x 95 mm are provided". "BP Apparatus tray: CRCA sheet construction with SS handle and SS hinge Dia 10 for handle. Sheet thickness 1.2 ,0.8 and 0.6. swivel tray is designed for BP Apparatus that can be concealed when not in use. SS Handle: SS 202 Dia 10 - Aesthetically designed handles are placed in such a way that gives a unique look also provide wider space for griping to users. "Ergonomics: Increased width of the table (625mm) gives better comfort for patients. Optimized height (808mm) of the table for comfortable observation and reach. Tapered shape is provided to give a unique look and better access for doctor. L-shape leg is provided for better stability." Single Step stool is made ofERW square tube. Textured and Rubber mat is provided, of 20mm X 20mm size. Tube 1.2 mm thick and mat 3.0 mm thick Size:485(L) x 335 (W) X 210 (H) Step stool is made of MS square tubes, is strong and firm. Top is made of textured rubber offering firm grip for climbing. Tissue roll Holder SS304 , made of ERW TUBE Ø12.7 mm and1.2 thk, isused to mount Tissue roll. Finish Specification - Powder coating is Bacteriostatic and thermosetting epoxy polyester,formulated to fulfill the requirements for bacterial protection. Performance Specification - Maximum patient load is 135 kg. Head Rest is adjustable 0 - 30°.BP Apparatus tray is provided to Swivel angle 0 to 180 deg. Approx. |
| 1311 | OT Table - Functional Specification: 1. Height adjustment - 730mm to 1020mm from Floor to mattress Top (Motorised), 2. Trendelenburg/Rev.Trendeleburg - 30° / 30°(Motorised), 3. Lateral tilt - 21° / 21°(Motorised), 4. Back rest (Up / Dn - from Horizontal) - 70° UP/ 50° DN (Motorised), 5. Leg rest - Flat, 6. Head rest (Up / Dn - from Horizontal) - 45° UP/ 45° DN (Manual), 7. Leg rest abduction (Left / Right) - 0° - 90° (Manual), 8. Maximum patient Load - 200 Kgs, 9. Power supply - 220 V, 5 Amp, 50 Hz, 10. Battery Back-up - Provided fitted with OT table as emergency power back for resetting the positions., 11. Lithotonomy crutches-Adjustable along Rod Axis, Rotation 360° around road Axis, Crutch pad adjustable in swivel joint. Material Specification: 1. Base Assembly - Aesthetically and scientifically designed T-Shape Heavy structure made of Ms Sheet flat and MS Casting with Zinc plating finish., Base is counter balanced for stability and structure is cover with 1.6mm thick SS 304 Fabricated sheet., 2. Column Assembly - Column is designed for self-lubricating, weldless, joint less and jerkless with high load carrying capacity.Column made by SS casting and complete assembly covered with SS 304 Fabricated sheet., 3. Table top Assembly-Top frame structure is made of SS 304 tubular frame of section 50mmX50mmX3mm Thk, 4. X-Ray Translucent top - X-Ray Translucent compressed laminate platform are provided on all sections of mattress support frame., 5. Matress - Molded Polyurethane foam mattress of density 55 Kg/Cu.m, Stitchless molded PU mattress ensure sterility and comfort, Mattresses are supported by 10mm Bakelite sheet., 6. Castor - Polyurethane twin wheel non-marking central lock heavy duty castor of wheel dia 100mm to suit the application of OT table., 7. Actuators and Control - Back rest , Height adjustment, Trendelenburg and Lateral Tilt are operated by linear actuator of Ti-Motion make.Actuators works on powder 24VDC with duty cycle - 10% Legrest and Headrest are operated manually & Height adjustment, Backrest, Trendelenburg and Lateral tilton actuator, 8. Crutches - Lithotomy crutches made of SS 304 Rod and molded polyurethane with ergonomic calf rest profile to suit the Operation table application. Finish Specification: 1. All SS parts - Glossy buff finish, 2. All MS Parts - Zinc plated, 3. Mattresses - Black color (molded), 4. Flexible bellow - Black color (Neoprene), 5. Calf pad - Black color (Molded) Compliances: CE, ISO 13485 & ISO 9001 |
| 1312 | Single Bed of size: 2060mm (W) x 915mm (D) x 650mm (H) x 400mm (Bed Stead Height) This dimension are product out to out dimension & variation ±1.0 cm are Normal. Bed Frame Assyembly: Bed Frame Assembly is a welded of side frame, Inner Slat. The side frame are made of Rect. Pipe 50.8 x 25.4 x 1.2 mm Thick MS, Inner Slats of SQ. Tube 19 x 1.0 MS ERW Tube IS : 7138 MS Sheet 1.0mm Thick. Head Board & Tail Board: Head Board & Tail Board are made up of SQ. Pipe 40.0 x 1.2 mm & SQ. Pipe 25 x 1.0 mm Thick MS ERW Tube IS : 7138 and Support Bracket 3.2mm Thick MS Sheet IS : 513 Head / Tail Board connected with bed frame with M8 Bolt. Finish: Epoxy Polyester Power Coated - Colour (as per work order) DFT - 40-60 Micron |
| 1313 | Mattress for Single Bed of Size - 78" x 36" of Thickness 10 cm. Mattress can be used both sides. Equal parts of Hard and PU Foam lend appropriate support to the user. Make - Peps / Kurlon / Godrej / King Koil |
| 1314 | Bed Side Locker has cabinet with lock and with plastic molded handle. There is space between plastic top and cabinet to keep the general items for the frequent use. Cabinet is provided with lock to keep the valuable items for the safety. Overall Size (in mm): 490L x 410W x 941H Material Specifications: 4Corner Tube made from ERW Round Tube of Section Æ 25.4mm having thickness 1.2mm. 4Cabinet made from 0.8mm thick CRCA Sheet, and is provided with lock. 4Top made from ABS of Section 2.2mm. Top has recessed and contoured shape for the better aesthic and usability. 4Knob made from Plastic molded knob with Matt finish with generous radii and dome shape for better grip. 4Castors of Section Æ 50mm made from Plastic molded castor placed in diagonal lokcing arrangement. Finish Specification: Anti microbial and thermosetting eproxy polyester Powder coating, formulated to fulfill the requirements for bacterial protection. Colour RAL White & Plastic parts in Grey. Performance Specification: Maximum safe working load - 5kg (on Top) + 5kg (On Middle) + 10Kg (on Bottom) |
| 1315 | Bed side Locker- Overall sizes 402 mm(L) x 422 mm(W) x 840 mm(H). Drawer si CRCA of 1mm thickness with ball slides for easy operation and lock,slide is MS with zinc plating and telescopic ball slides.the cabinet is CRCA of 1mm thickness with lock and ventilation holes.The top is SS 304 sheet of 0.8 mm section and castors dia is 50 mm with plastic molded castor,2 castor with lock,Handle material is ABS with recessed handle is provided to open the cabinet door.Powder coated eopxy polyster and RAL white powder,plastic parts in grey ss top with buffed mirror finish.The manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products. |
| 1316 | Over Bed Table of over all size : (L)899 mm X ( W)555 mm X (H) Adjustable from 970 mm to 1170 mm. OBT should be a height adjustable Over Bed Table. Table top Height can be adjusted with the help of operating lever and with help of plastic gear which is smooth and noise less. Base frame should be made of ERW Round Tubes(35 mm dia) and Oval Tubes(30X60 mm) Housing should be made of ERW Round Tubes(76.10mm). Operating lever Handle : Plastic injection molded lever handle with SS rod insert making strong and provides the wider area for the grip.Telescopic column with leadscrew EN8 ACME threadon Crank for smooth height adjustment of table top height. Table top frame should be made of MS tube 1.2mm thickness, should bedesigned to hold the top as well as extension works as a handle for the handling of over bed table. Top: MDF top with membrane press , should giveanti scratch Property with good surface finish. Also Glass Holder profiling should be provided on to it. Castors: High endurance anti-static,Plastic injection molded castors are provided of Ø50mm. Powder coating should be Bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection. All powder coated parts in RAL white. Plastic parts in Grey" |
| 1317 | Over Bed Table Fixed Height - Dimension: Top Size - 760 (L) x 360 (W) x 850 (H) mm Featured with Laminated board top extending over the width of the bed, Tubular Frame work with 50mm Dia. Non-rusting Castors, and Pre-treated and Powder Coated. |
| 1318 | Partition Screen- Three fold screen is a portable screen on castors having three screens which can be folded to provide privacy. Overall Sizes (L)2637 mm X ( W)640 mm X (H) 1720 mm Material Specifications 1 Fix Frame - Made from E.R.W Tube of Section Ø25.4 having Thickness 1.2 mm (To provide hinging to movable frame) 2 Movable Frame - Made from E.R.W Tube of Section Ø19.05 having Thickness 1.2 mm (Flexible frame has plastic hinge. It can be adjusted in provided space) 3 Leg Frame - Made from E.R.W Tube of Section SQ. 30 having Thickness 1.6mm 4 Caster Wheel - Of Section Ø50 (For Ease of movement) 5 Bush For Holding Pipe - Made from Nylon 6 (Plastic bush) 6 Screen - Casement fabric for screen which is opaque for providing modesty. Finish Specifications 1 Powder coating - Epoxy polyester. 2 Color - Powder coated parts in RAL white, Plastic parts in Gray (Pantone cool gray 8C), Casement fabric in green (RAL 6026) |
| 1319 | Single Step Stool. Overall Size - 485 (L) X 335 (W) X 206 (H)mm. Understructure - MS, section 20 X 20mm of thickness 1.6mm. Stool Top - MS thickness 1.2mm. Rubber Mat - Rubber thickness 3mm. Powder Coating - Anti Microbial and thermosetting epoxy polyester. Color - RAL white, rubber mat in grey. |
| 1320 | Two Step Stool. Overall Size - 660 (L) X 480 (W) X 392 (H)mm. Understructure - MS, section 20 X 20mm of thickness 1.6mm. Stool Top - MS thickness 1.2mm. Rubber Mat - Rubber thickness 3mm. Powder Coating - Anti Microbial and thermosetting epoxy polyester. Color - RAL white, rubber mat in grey. |
| 1321 | Saline Stand- Height adjustable saline stand should be mounted on 4 pronged castor base,base circle should have dia of 695 mm and stand ht should be adjustable from 1568 mm to 2121 mm.Stand should be combination of fixed and adjsutable tube. Fixed ms tube should be with 31.75mm dia 1.6 mm thick and telescopic ss tube should be 19mm dia 1.6 mm thich ss 304 made. The height of the SS telescopic tube should be adjustable by ms toughened nickel plated knob.The stand shoul have 4 nos 8 mm dia ss hooks for holding saline bags, maximum safe working load should be 3 kg per hook.base frame should be mounted on 50 mm dia 4 noshigh endurance anti static plastic moulded castors provided with digonally lockable.All metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.Powder coating should be antimicrobial and thermosetting epoxy polyester,formulated to fulfill the requirements for bacterial protection. |
| 1322 | Basin Stand - 4 legged basin stand mounted on castors. Overall Size:- Base circle dia 425 X (H) 850mm. Material Specification: Stand - SS 304 tube of section 12.7mm & 25.4 mm thickness 1.2mm, Bowl - SS 202 sheet, spin section, thickness 0.8mm. Castors - High endurance Plastic injection moulded castors, 50mm in dia. Finish Specification - SS (Buffed) glossy mirror finish. Performance Specification - Maximum safe working load 20 Kg. |
| 1323 | Medicine Trolley - Material Specification - Top Shelf - SS 304 Sheet, thickness 1mm, Supporting Legs -SS 304 tube, section 31.8mm pipe, thickness 1.2mm, Horizontal Bar - SS 304 Tube, section 12.7mm, thickness 1.2mm, welded with the legs. Bottom shelf - SS 304 Sheet, thickness 1mm. Castors - High endurance, Plastic injection moulded castors, section 125mm. Finish Specification - SS buffed to Glossy mirror finish. Performance Specification - Maximum safe working load 20Kg |
| 1324 | Instrument Trolley - overall dimensions (in mm) 900Wx 1800H x 450D and should have transparent doors and sides with steel frame work. Transparent portion of this cupboard should be made of Acrylic of 4mm thick. This cabinet should have 5 adjustable acrylic shelves each of 6 mm thickness. Three way lock should be provided of 6 levers. In the front door there should be 4 acrylic sheets and 2 each on both the sides. Metal used should be of CRCA and powder coated for finish. To be provided with rubber shoes to prevent direct contact of cabinet and floor. |
| 1325 | Oxygen Cylinder Trolley - mounted on castors. Size - L-410mm X W-375mm X H-1112mm. Material Specification : Main Frame - MS ERW Tube, Section 25.4mm Thickness 1.6mm for holding the cylinder. Locking Rod -MS Rod, section 10mm, keeps the cylinder in position during transit. Base Frame -MS ERW Tube, section 25.4 X 25.4, thickness - 1.6mm, sturdy base for resting the cylinder. Castor Wheel -PU wheel, section 100mm, thickness 25mm, for ease of movement. Leg Cap -LDPE, to cap the open ends at the bottom. Finish Specification-RAL White, epoxy polyster powder coating, plastic parts in pantone cool grey 8c. Performance Specification -Maximum safe working load 50 Kg. |
| 1326 | Desciption The Mayos Troley with Screw-Knob mechanism for height adjustment Overall Sizes 504mm x 650 mm X Adjustable from 814 mm to 1340mm Material Specifications 1. Bottom Frame - S.S. 304 TUBE, Squar-38 X 38mm Thickness 1.2mm (Square Tube for caster mounting and welded with thick plate and Buffed neatly.) 2 Top Frame - S.S. 304 TUBE, Rectangular 30x30mm Thickness 1.2mm 3. Fixed Tube - S.S. 304 TUBE, Square-38 X 38mm Thickness 2.6mm (Fixed Tube for providing guide way to telescopic tube) 4. Telescopic Tube - S.S. 304 TUBE, Rectangular 30x30mm Thickness 2mm (Buffed finish SS tube is used for the telescopic function to provide smooth operation without wear and corrosion) 5. Locking Knob mechanism - S.S. Screw with Nylon6 knob, Standard (Aesthetically and ergonomically designed Knob and lever mechanism is used to lock the SS telescopic tube at desired height. Knod 0D of Ø60mm) 6. Tray Supporting Frame - S.S. 304 TUBE, Square 30x30mm Thickness 1.2mm (Square Tube for Tray Mounting and welded with square tube and Buffed neatly / Square Tube for Supporting the top frame and welded with telescopic tube) 7. Tray - S.S 304, Bend Section Thickness - 1mm (Aesthetically designed flanged Section for usage as a tray) 8. Castors - High endurance, Plastic Injection molded castors, Ø50mm (For easy of movement) Finish Specifications S.S. - (Buffed) to Glossy Mirror Finish Performance Specifications Maximum safe working load - 20Kg Note: Overall dimesions may vary within ±5mm |
| 1327 | Crash Cart- Overall Sizes 1048 mm x 475mm x 1555mm Material Specifications 1 Top Shelf - Made from S.S.304 SHEET of thickness 1mm (ProvIded to keep materials at top) 2 Middle Shelf - Made from S.S.- 304 SHEET of thickness 1 mm (S.S. Shelf, provided for the placement of the instruments being used) 3 Bottom Shelf - Made from S.S. 304 SHEET of thickness 1 mm (Provided to keep materials at the bottom) 4 Frame - Made from S.S.304 Tube of section Ø25.4 r Sq19,1.2mm Thk Ø12.7mm tube 5 O2 Cylinder Case - Made from S.S Tube of section Ø12.7 tube and thickness 1.2mm (Used to mount 02 cylinder) 6 I V Pole - Made from S.S.304 Rod ø12 mm (Provision provided to mount IV rod) 7 Castor - Made from High endurance anti-static, plastic injection molded castors (Ø125mm wheel dia with positioned for diagonal locking Ø50 wheel for cylinder case) 8 Handle - Made from S.S. 304 PIPE of section Ø25.4mm and thickness 1.2mm (used To maneuver the trolly) 9 Bins - Made from PPCP (Six different Coloured bins are provided to keep medicines) 10 Drawer Set - Made from PPCP (Two drawer set with 3 drawer each central locking RH side on each set) 11 CARDIAC BOARD - Made from Compact laminate of thickness 6.0mm |
| 1328 | Patient Stool - SS Top Stool mounted on 4 leg Base & has a screw nut mechanism for height adjustment. It has a SS Top plate for sitting purpose. Overall Size - Base outer dia 538mm(H) Adjustable from 470mm to 655mm. Material Specification : Leg -MS ERW Tube Section 25.4 mm, Thickness - 1.6mm, Press formed pipe leg gives round & clean look and welded with round hub. Hub - MS ERW Tube, Section 38mm, Thickness 2.0mm Tube for bush mounting and welded with legs. Screw - EN-8, Section OD22, Used for height adjustment of seat base. Seat Base -Welded construction made up of MS ring & mounting plate. Top Plate - SS 202 Sheet, Section 305mm round, Thickness 1 mm, Top plate, provide asthetic look and it is non corrossive. Leg Shoes - Nylon 6, Moulded, Plastic bush avoid contact between metal & floor surface. Finish Specification: Epoxy polyster powder coating and buffed glossy mirror finish (SS Top), Plastic parts in Grey. Performance Specification: Maximum safe working load 135 Kg. |
| 1329 | Instrument Cabinet- overall dimensions (in mm) 900Wx 1800H x 450D and should have transparent doors and sides with steel frame work. Transparent portion of this cupboard should be made of Acrylic of 4mm thick. This cabinet should have 5 adjustable acrylic shelves each of 6 mm thickness. Three way lock should be provided of 6 levers. In the front door there should be 4 acrylic sheets and 2 each on both the sides. Metal used should be of CRCA and powder coated for finish. To be provided with rubber shoes to prevent direct contact of cabinet and floor. |
| 1330 | Doctor"s Table of size (in mm) 1500W x 750D x 740H, Top & Side Panel made of top of 25 mm thick plain particle board clad with 0.6mm thick post formed Laminate and 1 mm Thick Backing Laminate Flat Edge duly sealed with 2 mm thick PVC beading Modesty panel of 18mm thick plain particle Board clad with 1.0 mm thk DL on both sides, Edge with 2 mm thk PVC beading. ERU of size (in mm) 1050W x 520D x 705H Top: 25 mm Thick Plain Particle Board (PPB) Clad with 0.6mm thick Post Formed Laminate and 1mm thick Backing Laminate (BDL). Flat edge duly sealed with 2mm thick PVC Beading. Modesty Panel: 18mm thick Plain Particle Board (PPB) Clad with 1.0Mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2mm thick PVC Beading Mobile Pedestal of size (in mm): 646H x 390W x 440D 3 Drawers Free Standing Pedestal with Castor |
| 1331 | Doctor"s Table of size (in mm) 1500W x 750D x 740H, Top & Side Panel made of top of 25 mm thick plain particle board clad with 0.6mm thick post formed Laminate and 1 mm Thick Backing Laminate Flat Edge duly sealed with 2 mm thick PVC beading Modesty panel of 18mm thick plain particle Board clad with 1.0 mm thk DL on both sides, Edge with 2 mm thk PVC beading. ERU of size (in mm) 1050W x 520D x 705H Top: 25 mm Thick Plain Particle Board (PPB) Clad with 0.6mm thick Post Formed Laminate and 1mm thick Backing Laminate (BDL). Flat edge duly sealed with 2mm thick PVC Beading. Modesty Panel: 18mm thick Plain Particle Board (PPB) Clad with 1.0Mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2mm thick PVC Beading Mobile Pedestal of size (in mm): 646H x 390W x 440D 3 Drawers Free Standing Pedestal with Castor |
| 1332 | General Doctors Table Size: 1650W x 900D x 740H TOP SIDE PANEL: 25 MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK PVC BEADING. MODESTY: 18MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING. Mobile Pedestal: Free Standing Pedestal with Castors. Dimensions: 646W x 390D x 440H |
| 1333 | Executive Table- Main Desk with ERU & Pedestal made from - MAIN TOP - MDF + VENEER + PU Coating, Size: 1800 W * 900 D * 750 H, TOP THICKNESS – 65 mm. MODESTY- Size: 1640 X 600 X16 mm, MDF + Veneer + PU Coating. MOBILE PEDESTAL- MDF + Veneer + PU Coating, Size: 510W * 635H * 445D mm. ERU TOP - MDF + VENEER + PU Coating, Size: 1200W x 445D x 660H TOP THICKNESS – 25 mm. PU COATING HARDNESS 1.5H. |
| 1334 | Executive Table LHS with PED and Back Unit - Table of size (in mm) 1500W x 750D x 740H, Top & Side Panel made of top of 25 mm thick plain particle board clad with 0.6mm thick post formed Laminate and 1 mm Thick Backing Laminate Flat Edge duly sealed with 2 mm thick PVC beading Modesty panel of 18mm thick plain particle Board clad with 1.0 mm thk DL on both sides, Edge with 2 mm thk PVC beading. ERU of size (in mm) 1050W x 520D x 705H Top: 25 mm Thick Plain Particle Board (PPB) Clad with 0.6mm thick Post Formed Laminate and 1mm thick Backing Laminate (BDL). Flat edge duly sealed with 2mm thick PVC Beading. Modesty Panel: 18mm thick Plain Particle Board (PPB) Clad with 1.0Mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2mm thick PVC Beading Mobile Pedestal of size (in mm): 646H x 390W x 440D 3 Drawers Free Standing Pedestal with Castor Back Unit: Dimension: 1280 X 425 X 705. Top & Side Panel: 25 mm thick Plain Particle Board (PPB) Clad with 0.6mm thick post formed laminate and 1mm thick backing laminate (BDL). Flat edge duly sealed with 2mm thick PVC Beading. Doors, Partitions & Shelves: 18mm thick Plain Particle Board (PPB) clad with 1.0mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2mm thick PVC Beading. |
| 1335 | Executive Table LHS with PED and Back Unit - Table of size (in mm) 1500W x 750D x 740H, Top & Side Panel made of top of 25 mm thick plain particle board clad with 0.6mm thick post formed Laminate and 1 mm Thick Backing Laminate Flat Edge duly sealed with 2 mm thick PVC beading Modesty panel of 18mm thick plain particle Board clad with 1.0 mm thk DL on both sides, Edge with 2 mm thk PVC beading. ERU of size (in mm) 1050W x 520D x 705H Top: 25 mm Thick Plain Particle Board (PPB) Clad with 0.6mm thick Post Formed Laminate and 1mm thick Backing Laminate (BDL). Flat edge duly sealed with 2mm thick PVC Beading. Modesty Panel: 18mm thick Plain Particle Board (PPB) Clad with 1.0Mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2mm thick PVC Beading Mobile Pedestal of size (in mm): 646H x 390W x 440D 3 Drawers Free Standing Pedestal with Castor Back Unit: Dimension: 1280 X 425 X 705. Top & Side Panel: 25 mm thick Plain Particle Board (PPB) Clad with 0.6mm thick post formed laminate and 1mm thick backing laminate (BDL). Flat edge duly sealed with 2mm thick PVC Beading. Doors, Partitions & Shelves: 18mm thick Plain Particle Board (PPB) clad with 1.0mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2mm thick PVC Beading. |
| 1336 | Table Size in mm = 1365 X 680 X 750 having top made of 18 mm thick superior quality pre-laminated particle board of Grade II Type II conforming to IS:12823 of approved quality and shade.The edges of the table shall be banded with PVC strip 2 mm thick using hot melt glue under heat and pressure. The table top shall be supported by 1 mm thick M.S. ‘C’ frame stiffener of size 24.2 mm (W)x 38 mm (H). The table shall have 4 legs made ofElectric Resistant Welded prime quality CRCA steel round tubular frame of Dia 25.4mm size and of 1.2mm thickness.The base of legs of the tables shall be covered with plastic caps.The table shall have two no. drawer units i.e right side drawer unit shall have three box drawers & left side drawer unit shall have two box drawers.And overall size of drawer 355 mm (W) x 560 mm (D) x 430 mm (H). The drawer unit shall be made of 0.8 mm thick CRCA sheet and drawer trays shall be made of 0.6 mm thick CRCA sheet.The drawers shall glide on frictionless slides of 1.2 mm thick CRCA sheet and shall have a multi purpose steel lock with handles built in place.The drawer units to have a mechanism to ensure only one drawer opens at a time. Both the drawers are fitted to ‘C’ frame by machine screws.Joints shall be interlocked and welded to render a flawless appearance.All steel parts shall be pretreated for seven stage anti-corrosion treatment followed by powder coating of thickness 50–55 microns complete as per drawing and as per directions of Engineer in charge. The steel tube shall conform to IS: 3601 – 1984, IS: 7138 – 1973and IS: 4923 – 1985. |
| 1337 | Staff Table Size: 1199 x 590 x 735 mm having top made of 18 mm thick superior quality pre-laminated particle board of Grade II Type II conforming to IS:12823 of approved quality and shade. The edges of the table shall be banded with PVC strip 2 mm thick using hot melt glue under heat and pressure. The table top shall be supported by 1 mm thick M.S. ‘C’ frame stiffener of size 24.2 mm (W) x 38 mm (H). The table shall have 4 legs made ofElectric Resistant Welded prime quality CRCA steel round tubular frame of Dia. 25.4 mm size and of 1.2 mm thickness. The base of legs of the tables shall be covered with plastic caps. The table shall have one no. drawer units i.e. right side drawer unit shall have three box drawers. And overall size of drawer 355 mm (W) x 560 mm (D) x 430 mm (H). The drawer unit shall be made of 0.8 mm thick CRCA sheet and drawer trays shall be made of 0.6 mm thick CRCA sheet. The drawers shall glide on frictionless slides of 1.2 mm thick CRCA sheet and shall have a multi purpose steel lock with handles built in place. The drawer units to have a mechanism to ensure only one drawer opens at a time. Both the drawers are fitted to ‘C’ frame by machine screws. Joints shall be interlocked and welded to render a flawless appearance. All steel parts shall be pretreated for seven stage anti-corrosion treatment followed by powder coating of thickness 50–55 microns. |
| 1338 | Work Table - Desk with one drawer attachment Size 1200 x 600 x 750 (mm) Material - Prelaminated Particle Board with 18mm thick table top and 15mm thick understructure covered with PVC Lipping. Locking - Locking facility available for top draswer/s only. The manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products. |
| 1339 | Equipment Table - Table of over all size - 1180mm (W) x 460mm (D) x 750mm (H) Top: The top is in Stainless Steel brushed finish with PLB insert for durability. Easy to clean and maintain hygiene. Understructure: Side Frame Made from 30mm x 30mm x 1.5mm thick M.S Powder coated tubes at base which are welded and are fixed to top with screws. The bottom ends are closed with Plastic buffers. MS Shade : S/G Mettalic Dark Grey (Nerocoat - 9000626) Cross Member Made from 30mm x 30mm x 1.5mm thick M.S Powder coated tube, which is welded and bolted to side frames. |
| 1340 | 10 Seater Conference table of size 3000 x 1200 mm x 750 mm made from 1 WorkSurface: Veneered Top thickness 31mm Thick ±1.5mm (18mm±12mm MDF As per IS 12406 + 0.6mm Post Laminate on Top surface and balancing laminate on Bottom surface) with PVC banding on straight top side edge and speically designed T-Beading fixed side edge for sleek look. 2 Legs Made from 1.6mm Matt Silver Anodized Aluminum Extrusion. Leg Assembled together with a plasitc holder at bottom and 5mm HR Steel (IS: 2062) which is Powder coated (DFT 40-60 microns). The plastic glide holder is having provision for wire entry and glide fixing. The wire carrying is facilitated through the hollow space between two leg extrusions and the wires are concealed between removable rigid PVC extrusion in the Leg. 3 VEIL and Cross Member Made from 18mm thick PLT ± 1mm as per IS - 12823 and PVC edge banding on all the sides. 4 Access Flap & Switch Mounting Tray Made from Matt Silver Anodized Aluminium extrusion and plastic moulded components to facilitate access of Electrical / Data / Voice sockets access from top. Powder coated (DFT 40-60 Microns) switch mounting tray made from 0.8/1.2mm CR Steel IS-513. Switches to be mounted on tray as per requirement. Provision for mounting 8-module Anchor Roma switch plate on switch-mounting tray. |
| 1341 | Doctors Chair- High Back Chair with seat and back are made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE : 47.5 cm (W) x 69.5 cm (H) SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) The HR Polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16±2 kgf as per IS:7888 for 25% compression. The one-piece armrests are injection moulded from black Co-polymer Polypropylene. The mechanism is designed with the following features: • 360 degree revolving type. • Upright position locking. • Tilt tension adjustment. • Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt) The pneumatic height adjustment has an adjustment stroke of 12.0 cm.The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0cm pitch-center dia. (76.0 cm with castors. The twin wheel castors are injection moulded in 30% Glass Filled black Nylon." |
| 1342 | Staff Chair - Mid Back Chair with seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE : 47.5 cm. (W) x 58.0cm. (H) SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) The HR Polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16±2 kgf as per IS:7888 for 25% compression. The one-piece armrests are injection moulded from black Co-polymer Polypropylene. The mechanism is designed with the following features: • 360 degree revolving type. • Upright position locking. • Tilt tension adjustment. • Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt) The pneumatic height adjustment has an adjustment stroke of 12.0 cm.The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0cm pitch-center dia. (76.0 cm with castors. The twin wheel castors are injection moulded in 30% Glass Filled black Nylon." |
| 1343 | Visitor Mid Back Chair with seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE : 47.5 cm. (W) x 58.0cm. (H) SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) The HR Polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16±2 kgf as per IS:7888 for 25% compression. The one-piece armrests are injection moulded from black Co-polymer Polypropylene. The mechanism is designed with the following features: • 360 degree revolving type. • Upright position locking. • Tilt tension adjustment. • Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt) The pneumatic height adjustment has an adjustment stroke of 12.0 cm.The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0cm pitch-center dia. (76.0 cm with castors. The twin wheel castors are injection moulded in 30% Glass Filled black Nylon." |
| 1344 | Attendant Chair - SS Top Stool mounted on 4 leg Base & has a screw nut mechanism for height adjustment. It has a SS Top plate for sitting purpose. Overall Size - Base outer dia 538mm(H) Adjustable from 470mm to 655mm. Material Specification : Leg -MS ERW Tube Section 25.4 mm, Thickness - 1.6mm, Press formed pipe leg gives round & clean look and welded with round hub. Hub - MS ERW Tube, Section 38mm, Thickness 2.0mm Tube for bush mounting and welded with legs. Screw - EN-8, Section OD22, Used for height adjustment of seat base. Seat Base -Welded construction made up of MS ring & mounting plate. Top Plate - SS 202 Sheet, Section 305mm round, Thickness 1 mm, Top plate, provide asthetic look and it is non corrossive. Leg Shoes - Nylon 6, Moulded, Plastic bush avoid contact between metal & floor surface. Finish Specification: Epoxy polyster powder coating and buffed glossy mirror finish (SS Top), Plastic parts in Grey. Performance Specification: Maximum safe working load 135 Kg. |
| 1345 | Executive high back chair- Executive Mid Back Chair having Seat/Back Assembly: The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H) Seat Size - 51cm (W) x 48cm (D) Armrest (Adjustable): The armrest top is made up of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height is adjustable up to 6.5±0.5cm in 5 steps & also has swivel adjustment of 22° ± 2° on both sides. Knee Tilt Synchro Mechanism with Seat Deapth Adjustment Mechanism: The mechanism is designed with the following features - 360° revolving type, Single point control, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat back tilting ratio of 1:2 & Seat depth adjustment of 6.0 ± 0.5cm can be locked in 6 positions. Adjustable Backrest: The backrest consists of a sliding up down mechanism, which can be adjusted in the range of 7.5 ± 0.5cm and can be locked in 4 positions for correct position of lumber support. Pneumatic Height Adjustment: The pneumatic height adjustment has an adjustment of 9.0 ± 0.3cm. Pedestal Assembly: The pedestal is fabricated from 0.2 ± 0.2cm thick HR sheet (IS : DD 1079 / HR skin pass), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.0±0.5cm Pitch-center dia. (76.0 ± 1.0cm with castors). Twin Wheel Castors:The twin wheel castors are injection moulded in black Nylon. |
| 1346 | Chair Mid Back with seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE : 47.5 cm. (W) x 58.0cm. (H) SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) The HR Polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16±2 kgf as per IS:7888 for 25% compression. The one-piece armrests are injection moulded from black Co-polymer Polypropylene. The mechanism is designed with the following features: • 360 degree revolving type. • Upright position locking. • Tilt tension adjustment. • Seat/back tilting ratio of 1:3 (60 seat tilt/180 back tilt) The pneumatic height adjustment has an adjustment stroke of 12.0 cm.The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0cm pitch-center dia. (76.0 cm with castors. The twin wheel castors are injection moulded in 30% Glass Filled black Nylon." |
| 1347 | Visitor Chair- SEAT/BACK ASSEMBLY: The seat / back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam together with moulded seat and back covers. The back foam is designed with contoured lumbar support for extra comfort.(MEDIUM BACK) SIZE: 50.0cm. (W) X 49.0cm. (H). SEAT SIZE: 50.0cm. (W) X 46.0cm. (D). POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. SEAT / BACK COVERS: the seat and back covers are injection moulded in black co-polymer polypropylene. ARMRESTS: The one-piece armrests made of black integral skin polyurethane with 50-70 Shore ‘A’ Hardness and reinforced with M.S. insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.5cm. thk. HR steel.TUBULAR FRAME : The tubular frame is cantilever type & made of Dia.2.54cm. (1”) x 14 BG M.S. E.R.W. tube and black powder coated. |
| 1348 | Conference Chair- Executive Mid Back Chair having Seat/Back Assembly: The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H) Seat Size - 51cm (W) x 48cm (D) Armrest (Adjustable): The armrest top is made up of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height is adjustable up to 6.5±0.5cm in 5 steps & also has swivel adjustment of 22° ± 2° on both sides. Knee Tilt Synchro Mechanism with Seat Deapth Adjustment Mechanism: The mechanism is designed with the following features - 360° revolving type, Single point control, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat back tilting ratio of 1:2 & Seat depth adjustment of 6.0 ± 0.5cm can be locked in 6 positions. Adjustable Backrest: The backrest consists of a sliding up down mechanism, which can be adjusted in the range of 7.5 ± 0.5cm and can be locked in 4 positions for correct position of lumber support. Pneumatic Height Adjustment: The pneumatic height adjustment has an adjustment of 9.0 ± 0.3cm. Pedestal Assembly: The pedestal is fabricated from 0.2 ± 0.2cm thick HR sheet (IS : DD 1079 / HR skin pass), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.0±0.5cm Pitch-center dia. (76.0 ± 1.0cm with castors). Twin Wheel Castors:The twin wheel castors are injection moulded in black Nylon. |
| 1349 | Stool - Square Stool of Overall dimensions: 411 mm(L) x 411 mm(W) x 522 mm(H). The structure is MS flat with 2mm thickness and shoe is PVC+nitrile.The top is SS 304 sheet of 0.8 mm thickness and powder coated with epoxy polyster and colour is RAL white poeder,plastic and rubber parts in gray,SS top buffered mirror finish.Maximum safe working load is 100 kg.The manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007 and should have Green Guard Certification for few of its products. |
| 1350 | Cushion Chair - Chair of Over all size: 58.0cm (W) x 56.5cm (D) x 87.5cm (H) & 48.0cm (SH) SEAT/BACK ASSEMBLY: The seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather-cloth, and U-foam. *BACK SIZE: 46.0cm (W) x 27.0cm (H). *SEAT SIZE: 46.0cm (W) x 40.0cm (D). ARMREST TUBE: The armrest tube is made of M.S. E.R.W. tube dia. 2.54cm. (1”) x 16BG thick and powder coated. ARMREST: The armrest is gas-assisted injection moulded from black Polypropylene. UNDERSTRUCTURE ASSEMBLY: The understructure assembly is a cantilever type frame made of dia. 2.54cm. (1”) x 14BG. thick M.S. E.R.W. tube and powder coated. |
| 1351 | Three Seater Waiting Chair- 3 seater with 2 arms & without cushion of Size in cm - 163W x 57D x 67.5H Seating height of 40cm CROSS BEAM: It is made up of black powder coated rectangular M.S.ERW tube having 8d0 ± 0.03 cm x tO ± 0.03 cm x 0.2 ± 0.014 cm size. LEG AND ARMREST: It is chrome plated made of cold rolled steel with 0.12 ± 0.013 cm thinkness. SEAT/BACK SHELL: It is powder-coated perforated shell made from cold rolled M.S. sheet (DIN1 623 PartI ST-12 Grade) 0.14 ± 0013 cm thickness.The Side Bar is made of Chrome plated solid steel 3.0 ± 003 cm x 1.2 ±0.3 cm with fluting and plastic inserts. The Shell is assembled on the Cross Beam with help of M8 Bolts (Per Seat - 8 nos. Seat to Bracket and 4nos. Bracket to Cross Beam). CUSHION (optional feature): The seat & back cushion are made up of PU foam upholstered with leather cloth or fabric with plywood. |
| 1352 | 1Seater Sofa of overall size - 86cm (W) x 92cm (D) x 82cm (H) & Seat Height 45cm. 1) SEAT FOAM: The seat is made of PU foam with Density32 ± 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 ± 2 kg/cu.mtr. Seat is upholstered with fabric or leatherette. 2) BACK FOAM: The back is made of PU foam with Density 28 ± 2 kg/cu.mtr with two additonal top layer of supersoft foam of density 23 ± 2 kg/cu.mtr upholstered with fabric or leatherette. 3) UNDERSTRUCTURE: Understructure is made up of 1.2 ± 0.1 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-184 Dia 4mm zigzag spring assembly is mounted in understructure for support and additional cushioning purpose. 4) LEG ASSEMBLY: It is a welded assembly made in stainless steel (grade SS 202) tube & plate. |
| 1353 | 2Seater Sofa of overall size - 146cm (W) x 92cm (D) x 82cm (H) & Seat Height 45cm. 1) SEAT FOAM: The seat is made of PU foam with Density32 ± 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 ± 2 kg/cu.mtr. Seat is upholstered with fabric or leatherette. 2) BACK FOAM: The back is made of PU foam with Density 28 ± 2 kg/cu.mtr with two additonal top layer of supersoft foam of density 23 ± 2 kg/cu.mtr upholstered with fabric or leatherette. 3) UNDERSTRUCTURE: Understructure is made up of 1.2 ± 0.1 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-184 Dia 4mm zigzag spring assembly is mounted in understructure for support and additional cushioning purpose. 4) LEG ASSEMBLY: It is a welded assembly made in stainless steel (grade SS 202) tube & plate. |
| 1354 | 3Seater Sofa of overall size - 205.5cm (W) x 92cm (D) x 82cm (H) & Seat Height 45cm. 1) SEAT FOAM: The seat is made of PU foam with Density32 ± 2 kg/cu.mtr having an additional top layer of PU foam with Density 28 ± 2 kg/cu.mtr. Seat is upholstered with fabric or leatherette. 2) BACK FOAM: The back is made of PU foam with Density 28 ± 2 kg/cu.mtr with two additonal top layer of supersoft foam of density 23 ± 2 kg/cu.mtr upholstered with fabric or leatherette. 3) UNDERSTRUCTURE: Understructure is made up of 1.2 ± 0.1 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-184 Dia 4mm zigzag spring assembly is mounted in understructure for support and additional cushioning purpose. 4) LEG ASSEMBLY: It is a welded assembly made in stainless steel (grade SS 202) tube & plate. |
| 1355 | Centre Table of Overall Size: 112W x 60D x 35.1H (cm) with Glass 12±0.3 mm thick black tinted Toughened Glass UV glued with bushes made in SS 202 grade for fixing with understructure. Understructure: Welded Assembly made in SS 202 grade having Dia. 12±0.04 as per IS:1762. |
| 1356 | Side Table- Corner Table of Overall Size: 60W x 60D x 35.1H (cm) with Glass 12±0.3 mm thick black tinted Toughened Glass UV glued with bushes made in SS 202 grade for fixing with understructure. Understructure: Welded Assembly made in SS 202 grade having Dia. 12±0.04 as per IS:1762. |
| 1357 | Over Head Storage Unit- Wall mounted Storage Unit of Size (in mm) - 600W x 326D x 785H & Door with lock 18mm Thick of Size (in mm) 298W x 783H. Storage Unit made of a sturdy metal carcass structure with Wooden Shutters. |
| 1358 | Personal Locker Unit of Size - 380 mm (W) x 450 mm (D) x 1830 mm (H). Lock- 10 Lever cam lock with lock lever. Material - CRCA 0.6mm Thickness. Construction- Rigid knockdown construction. Shelf- Uniformly Distributed Load Capacity per each shelf level is 35 Kg maximum. Finish- Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). Handle/ Label Holder- Aesthetically appealing Snap fit ABS plastic Handle.Plastic label holder for identification. Ventilation- Attractive punched pattern for ventilation. The manufacturer should be having certifications like; BIFMA, ISO 9001:2008, ISO 14001:2004, ISO 18001:2007. |
| 1359 | 4Door Book Case- Size : 914 mm (W) X 320 mm (D) x 1742 mm (H) Construction & Material Rigid Knock down construction. • Top panel, Back panel and Side panel are made from 0.7mm high yield strength CRCA, rest in O.8mm CRCA Configuration (Doors) - 4 Door Door Features / Locking - Each Door has 6 Lever Cam lock with common key. Each Door has 3 mm Thk transparent glass for clear inside vision secured in a Metal Frame through rubber gasket. Each door has a Scissor mechanism for receding inside the top of respective compartment & ensures parallel & smooth movement. Each door has Plastic side end caps as Handle which is easy to grip Behind Storage Shelving - Each compartment has storage shelf Uniformly Distributed Load Capacity per each shelf is 80 Kg maximum. Top Panel - 4 Door has Inside Metal Top Panel Finish - Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). |
| 1360 | Steel Almirah of Size - 1980mm (H) X 916mm (W) X 486mm (D), Construction & Material -Welded Construction, 0.7mm thick (±0.07mm) CRCA (D Grade as per IS:513) for shelf, 0.8mm thick (±0.08mm) High yield strength (D Grade High yield Strength as per IS:513) CRCA for Doors & Back,0.9mm thick (±0.08mm) CRCA (D Grade as per IS:513) for all other components. Locking & Handle - Mazak Handle, Three way locking mechanism with shooting bolt. Shelving - Height wise adjustable shelf mounting, Uniformly distributed load capacity per each full shelf is 40 Kg maximum, 4 Nos. adjustable full shelf, Leveler - M10 Screw type leveler with hex plastic base.Finish - Epoxy powder coated to the thickness of 50 microns ( ±10) |
| 1361 | Steel Rack 6 Sleeves- Slotter Angle Rack with Load bearing members of the system should be made out of High strength HR steel having properties equivalent to grades specified by IS 5986:2002 / IS 2062:2006 In addition to high strength, the raw material used for structural load bearing members also should possesses adequate ductility to ensure toughness. The material should also have the necessary impact strength for cold room applications upto -30° C Surface finish: All components must have thorough anti-rust treatment to prevent corrosion, thereby increasing the life of the component. Steel components must be powder coated for obtaining a smooth, scratch resistant and a lasting attractive, finish. The Dry Film Thickness (DFT) of 35 microns is required on an average after Powder coating. All components are to be an elaborate 4 step, six zone anti corrosion treatment, viz. De-greasing as per IS 6005:1970, Rinsing, Phospating as per IS 3618:1966 and De-mineralized water rinsing. Angle: Vertical load carrying member that transfers load to the ground via base plates, its Material Specifications should be as per IS: 5986 (ST 42). Angles should be of rolled formed construction to ensure minimal residual stresses and accuracy throughout the length of the angles, and should take the designated load. Slots at every 19.05 mm for height optimisation or adapt to ever changing SKU sizes and Grouted through base plates. Surface Finish: Epoxy-Polyester Powder Coated – Lead Free BS Grey/Oxford Blue in colour. Panel: Should conform to IS:513 D, and minimum yield strength 210 MPa. C12 No. of bends : 6 Manufacturing : Press forming.Panels are to be provided with lipped flanges. Width of the flange being 31 mm and depth of lip 17 mm. Panels are provided with 9 mm holes on the flange for corner plates, cladding sheets. Design Criteria : Deflection to be under SEMA guidelines. Surface Finish : Epoxy-Polyester Powder Coated – Lead Free BS Grey/Oxford Blue in Colour. SIZE: Width - 36" Depth: 18” Height: 6’ Load Capacity : 80 kg / loading level UDL (Uniformly Distributed Load) |
| 1362 | Lab Table Wall Side Unit- Practical Table for Wall Side Area of Size in mm: 3700L x 760W x 900H approx. with Granite Top and Understorage of Shelf & Drawer made of Steel Frame Panels & Shutters. The steel frames, panels & shutters are made from Prime Quality CRCA Steel. All cabinet bodies are of over closing design with fully knock down construction and having a main and add on construction to avoid any gaps in between two units. All units have interlocking type construction to form a rigid integral structure.These units are supported on wide base high grade plastic legs of diameter 40 mm. These legs are height adjustable with a range of +/- 50 mm. Each unit has a locking facility with 180° and 10 lever cam lock mechanism. • Surface Treatment: The complete M.S. material to be pre–treated and epoxy powder coated. The thickness of powder coat to be 50 microns, which passes the test of Salt Spray for 1000hrs and having Scratch Hardness of 3Kgs. • Cabinet frame: Frame of 1.2mm horizontal stiffeners and 0.8mm vertical panel of CRCA MS sheet. • Cover panels: All panels 0.8mm thick CRCA MS sheet. • Shelves and Drawers: CRCA shelves have a load carrying capacity of 40kg per shelf and overall carrying capacity of 80kg of UDL of a cabinet. • Door Pulls: Pull should be SS steel (SS304) with D type construction. Flush pulls for sliding doors should be of PVC, providing a recessed finger grip. • Slides: High precision Double Extension Ball slides which enable the drawer to open fully with a 15kg load in the drawer. • Shutters: Metal Shutters are double walled and made up of 0.8mm thick CRCA MS sheet with profil inserts and 40-50 microns pure epoxy powder coated. • Legs: All Legs to be made of plastic with a load carrying capacity of 450 kg/each. All units to be on plastic legs for better clean ability of the lab area. Leg should be able take evenness of the floor. It should have at least 50mm adjustability. • Storage Units: Storage unit with one drawer, one/ two shutters and one adjustable shelf. |
| 1363 | Revolving Stool Hight Adj. Hi Base - DIMENSIONS (±1.0cm) : 65.0cm(W)x65.0cm(D)x67.0-78.5cm(H) Seat Height-48.5.5cm. SEAT ASSEMBLY : Seat size - Dia 40.0cm, Adjustments - 360° Revolving type. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 ±2 Kg/m3 and Hardness load 16±2 kgf as per IS:7888 for 25% compression. HEIGHT ADJUSTMENT : The manual height adjustment is very easy to operate with a help of a knob. It can be easily locked at the most comfortable position. PEDESTAL ASSEMBLY: The five-prong pedestal is fabricated from 0.2±0.02 cm thick HR Sheet (IS: DD 1079 / HR), powder coated (DFT 40-60 microns) and fitted with an Injection moulded black Polyurethane Hub Cab and 5 nos. twin wheel castors. The pedestal is 55.0±0.5cm pitch circle diameter (65.0±1.0cm with castors). Circular foot ring of ø52.0±0.2cm made up of ø1.9±0.2 x 0.12±0.0096cm thick MS ERW Tube for foot support in High-base Stool TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. These dimensions are product out to out dimensions & variations within ±1.0cm are normal. |
| 1364 | Modular Kitchen with Granite work top and under structure as per Engineer In-Charge |
| 1365 | MEDICAL GASES PIPELINE |
| 1366 | Supply, Installation, Testing & Commissioning of Medical Gases Pipeline System complete with followings as per technical specifications & list of acceptable makes attached. |
| 1367 | Oxygen System |
| 1368 | Oxygen Manifold 5 + 5 cyclinder banks (cylinder excluded) |
| 1369 | Automatic Control Panel for the Oxygen Manifold System. |
| 1370 | Emergency Oxygen Manifold 2 + 2 cyclinder banks (cylinder excluded) |
| 1371 | Oxygen Flowmeter with humidifier Bottle with probe |
| 1372 | Oxygen Gas outlet points with probe/adaptor. |
| 1373 | Oxygen H.P.Rubber tube (White) |
| 1374 | Wall box for oxygen outlets |
| 1375 | Nitrous Oxide |
| 1376 | Nitrous Oxide Manifold 2 + 2 cyclinder banks (cylinder excluded) |
| 1377 | Automatic Control Panel for the Nitrous Oxide manifold System. |
| 1378 | Emergency Nitrous Oxide Manifold 1 + 1 cyclinder banks (cylinder excluded) |
| 1379 | N2O Gas outlet points with probe/adaptor. |
| 1380 | N2O H.P.Rubber Tube (Blue) |
| 1381 | Compressed Air System |
| 1382 | Compressed Air system of capacity 4x15HP Reciprocating Air Compressors, 1618LPM, 57 CFM, Air Dryers / Air Filters, Pre-filters, Activated Carbon Filters, Vertical Air Receiver of capacity 1500 Ltrs & Pressure Reducer |
| 1383 | Medical Air 4 Bar Gas outlet points (Imported) with probe/adaptor |
| 1384 | Surgical Air 7 Bar Gas outlet points (Imported) with probe/adaptor. |
| 1385 | MA-4 H.P.Rubber Tube (Black) |
| 1386 | Vacuum System |
| 1387 | Vacuum system of capacity 4x7.5HP Reciprocating Vacuum Pumps, 111 CFM, Vertical Air Receiver of capacity 2000 Ltrs |
| 1388 | Vacuum Gas outlet points with probe/adaptor. |
| 1389 | Ward suction Unit with 2000ml Jar |
| 1390 | Theatre Suction Unit with 2000ml Jar |
| 1391 | Vacuum H.P.Tube antistatic tube (Yellow) |
| 1392 | Wall box for Vacuum outlets |
| 1393 | Area Alarm Panels |
| 1394 | 5 Gases |
| 1395 | 3 Gases |
| 1396 | 2 Gases |
| 1397 | Master Alarm |
| 1398 | Area Valve box units |
| 1399 | 5 Gases |
| 1400 | 3 gases |
| 1401 | 2 gases |
| 1402 | Medical Grade Isolation Valves |
| 1403 | 35mm |
| 1404 | 28mm |
| 1405 | Medical Grade Copper Pipeline (In Mtrs.) |
| 1406 | 12 mm (OD) x 0.9 mm Thickness |
| 1407 | 15 mm (OD) X 0.9 mm Thickness |
| 1408 | 22 mm (OD) X 0.9 mm Thickness |
| 1409 | 28 mm (OD) X 0.9 mm Thickness |
| 1410 | 35 mm (OD) X 1.2 mm Thickness |
| 1411 | Bed Head Panel having Accessories Channel x 1, colour combination, as per Hospital requirement including, Stainless Steel Utility Basket, IV Stand Extendable Type with Aluminum Slider, Electrical Sockets (15/6 Amps) x 4 points & provision For Gas outlet for O2=1, VAC=1, MA=1, RJ-11=1, RJ-45=1 |
| 1412 | Electrical Control Panel for Compressed Air System and Vacuum System with wiring inside the plant room |
| 1413 | MODULAR OPERATION THEATRE |
| 1414 | Providing&installationofPreciselypre fabricated wall & Ceiling Cladding using steel sheet of approx 1.2 mm with EGP of approx300 microns. Wall sloping and ceiling panels backed gypsum plaster board to provide strength to withstandjerksandavoiddamageasper tech. specs. attached. |
| 1415 | Supply & laying of water based aseptic & self sterilizing wall coating with Anti fungal & Anti Bacterial Paint andother related painting components (viz: Primer, Putti etc.) of approved make and shadesso as to present a joint less finish etc. as per tech. specs. attached. |
| 1416 | Supply and laying of 2mm thick washable anti static seamless flooring with perfectly curved flash coving, resistant to mechanical stresses & dynamic loads & having ESD / EMI (conductive) protection characteristics. (Approx.), Coved Corners of approved make & shade. The joints of PVC tiles should be welded by special PVC thermal welding units using PVC welding bars colours. It should be scratch proof. The PVC flooring should be inert to body fluids, chemicals and disinfectants and should not be affected by temperature variation in the OT. The floor should efficiently discharge electric charges up to 2 kV. The conductive copper grid laid underneath the PVC sheet should be supported by liquid epoxy compounds allowed to set as a uniform and level surface & as per technical specs attached. |
| 1417 | Supply & fixing of sliding typeOT door having high density particle board cores, high pressure laminate face on both sides, viewing window 300 x 300mm. Standard Size: 1500 x 2100 mm (W x H) |
| 1418 | Supply, installation, testing & commissioning of multi colour coded Surgeon Control Membrane Touch Panel, flushed in the theatre wall comprising of the following features & as per technical specification attached: 1. Display of Day Clock 2. Display of Elapse Time Clock 3. Dimmer for peripheral lights 4. Medical Gas Alarm 5. Hands free telephone 6. Indicator for temperature & Humidity |
| 1419 | Supply, installation, testing & commissioning of Twin Plate X-Ray viewing screen designed to provide a high level of control luminance without Flickering & as per the technical specification attached. X-ray view screen (two screen) LED Overall dimensions (LxHxT) 880 x 503 x 29mm View area (WxH) : 736 x 440 mm Light source : LED Power consumption / input power : 30W / AC 100-240V Illumination intensity : 5,500 LUX approx. |
| 1420 | Supplying & fixing of sturdy writing board of size: 840mm x 640mm with perfect marker writing surface in front and back is laminated to make water proof surface. The board has to be provided with anodized aluminium framing and its back should have hooks for wall hanging of approved make and type directly on wall & as per technical specs attached. |
| 1421 | Fabrication, Supply & installation of mounted flushed with the theatre wall, storage unit size 1666 x 865 x350mm having two shelves, made of 1.5 mm thick EGP with 120 microns provided with Antifungal and Antibacterial surface coating of approved colour and shades duly provided with 5mm thick acrylic sheet in front with sliding arrangement & as per tech. specs attached. |
| 1422 | Supply, installation, testing & commissioning of SS Fabricated Cascade pressure stabilizer having SS blades to control Operation Theatre Room - Air Pressure of approved make as per tech. specs attached. |
| 1423 | Supply, installation, testing & commissioning of Recess Mounted IP54 LED clean room protocol, non–hygroscopic peripheral lights having CRCA housing lumen pack of 5600Lm with system wattage of 60 watt. The fitting should be Bottom opening type with high reflected clear acrylic glass with dimmer control from the Surgeon Control Panel. Specially designed for Clean Room Applications, such as Modular OT & as per tech. specs attached. |
| 1424 | Providing & fixing of double arm multi moveable surgeons pendant with load carrying capacity of 80Kg and rotational values of 330-340 degree with adjustable stopper. The pendent should be designed with service head to host, base, gas module, electric modular and shelves upto 8 gas outlets & 10 Electrical switches. Racks & Shelves should be provided to mount the equipments like monitor etc. The surgeon pendent should have two arms as per technical specs attached. |
| 1425 | Providing & fixing of single arm (900mm) anaesthesia pendant with load carrying capacity of 80Kg and rotational values of 330-340 degree with adjustable stopper. The pendent should be designed with service head to host, base, gas module, electric modular and shelves upto 8 gas outlets & 10 Electrical switches. Racks & Shelves should be provided to mount the equipments like monitor etc. The surgeon pendent should have two arms as per technical specs attached. |
| 1426 | Providing & installation of LED operating light having Maximum illuminance (1m): 110,000 + 110,000 Lux at 1m distance, Electrical power: 150 + 90 W, Power consumption: 2x 11 A, Fitting: Ceiling anchoring ring ceiling pendant with 2 brackets and 2 spring arms, Range of movement: 1x 360° / 1x 330°, Recommended room height: at least 2.45 m, Max. ceiling load: 2x 218 Nm / 650 N, Light body weight: 9.2 + 7.5Kgs, Light body depth: 1x 130 cm / 1x 140 cm, Air shielding surface: 2 x 330 cm2 Transformers: 2x 450VA/230V/26V, Brightness regulator: 2x 20 – 500 VA (primary voltage), Provided with 2 Sterilisable handles with each dome, Easy positioning by sterilisable handle, Focus adjustable by sterilisable handle, Life time of Bulbs :45,000 hours etc as per technical specifications attached. |
| 1427 | Providing & installation of Scrub Station Automatic Wall Mounted ( Double User) (2 Bay) Stainless Steel Scrub Set for Double user, two taps automatic with Sensor Detection System. Dimension: 120 (W) X 54 (D) X 84 (H) cms.(Approx.) |
| 1428 | CURTAIN & IV HANGER SYSTEM |
| 1429 | Supply, Installation, Testing & Commissioning of Curtain & IV Track System complete with following as per technical specifications attached.(Acceptable Makes : |
| 1430 | Providing and installation of Cubical tracks system made of Powder coated Aluminium alloy, mounted on the ceiling using Suspension hangers and bushes, powder coated wall bracket and Track Joiners wherever required. This system shall be complete with stain free polyster fabric, Water repellent Curtains having 18" Net on top. The curtain shall be approx 7X4 feet, with two curtains stiched together wherever required. Curtains shall also be provided with smooth movement, non sticking runners, with Stainless steel hooks, for easy movement. The system shall have curtain removal points and end cap complete as per technical specifications wherever is required.(Acceptable Makes : |
| 1431 | Providing and installation of I.V. Hanger with 5 hooks, made from mirror finish stainless steel, 304 grade with adjustable height, provided with 4/6 feet aluminium alloy track powder coated with endcap of tracks, 1 pc of trolley for smooth IV Hanger movement on track, 2 pcs of suspension hanger powder coated, top & bottom bush, powder coated, for easy fitting and better aestheticscomplete as per technical specifications is required.(Acceptable Makes : |
| 1432 | Add 18% GST |
| 1433 | Add 1% Labour cess 1% |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
