Military Engineer Services-MES has published Tender For Repair To Flooring, Plastering, Roofing, Periodical Services And Certain E/M Repairs In Permanent Bldgs At Lower Camp Khundru Under Ge 861 Ews.. Submission Date for this Tender is 30-05-2023. Shed Construction Tenders in Anantnag Jammu And Kashmir. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 04-May-2023 | REVISED BOQ | BOQ | 16-05-2023 |
| 2 | 16-May-2023 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 23-05-2023 |
| 3 | 23-May-2023 | Extension of bid submission end date | Date | 30-05-2023 |
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. |
| 2 | Demolition of brick work or stone boulder masonry built in cement mortar including all arches quoins etc but excluding ashlar facing, dressed stone work & precast concrete articles etc complete all as specificed and directed by Engr-in-Charge. |
| 3 | Demolition of cement concrete (unreinforced) in ground floors & paving n.exc15 cm thick (below or above ground level) complete all as specified and directed by Engr-in-Charge. |
| 4 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed by Engr-in-Charge. |
| 5 | Dismantling boarding of any description, fixed in any position with nails, complete all as specified and directed by Engr-in-Charge. |
| 6 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm complete all as specified and directed by Engr-in-Charge. |
| 7 | Taking down chowkat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed by Engr-in-Charge. |
| 8 | Taking down shutter of anydescriptionarea n.exc1.00 sqm each complete all as specified and directed by Engr-in-Charge. |
| 9 | Taking down of shutter any description area exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed by Engr-in-Charge. |
| 10 | Dismantling timber scantling unframed 40 sq cm and over in section in any position, complete all as specified and directed by Engr-in-Charge. |
| 11 | Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed by Engr-in-Charge. |
| 12 | Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed by Engr-in-Charge. |
| 13 | Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed by Engr-in-Charge. |
| 14 | Dismantlingplain or corrugated steel sheeting , any gauge and thickness,including Nainital or similar pattern roof coverings, complete all as specified and directed by Engr-in-Charge. |
| 15 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar, complete all as spcified and directed by Engr-in-Charge.. |
| 16 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all asspecified and directed by Engr-in-Charge. |
| 17 | Brick work with sub class "B" bricks straight or curved on plan, exceeding 6m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed by Engr-in-Charge. |
| 18 | All as per the description of item No. 17 here-in- before but except bricks. |
| 19 | Brick work with sub class "B" bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:4, complete all asspecified and directed by Engr-in-Charge. |
| 20 | Walling of random rubble masonry with best quality stone, uncoursed, well bonded, bedded and solidly hearted and built in CM 1:6, all as specified and directed by Engr-in-Charge. |
| 21 | All as per the description of item No. 20 here-in- before but except stones. |
| 22 | 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. |
| 23 | Flush pointing to randomrubble, uncoursed or brought upto courses masonry in Cement Mortar 1:4 all as specified and directed by Engr-in-Charge. |
| 24 | 10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. |
| 25 | 20mm thick rendering on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge. |
| 26 | Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile n.exc. 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed by Engr-in-Charge. |
| 27 | Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed by Engr-in-Charge. |
| 28 | Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:6, complete all as spcified and directed by Engr-in-Charge. |
| 29 | Glazed ceramic coloured tiles 450mm x 300mm x 6mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry,pointed in white or coloured cement to matchover and including 10mm thick renderingin cement mortar 1:4 to receive tiles, complete all as specified and directed by Engr-in-Charge. |
| 30 | Vitrified tiles 10 mm thick, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engr-in-Charge. |
| 31 | Chequered coloured cement concrete tiles of size 300 x 300 x 18-20mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engr-in-Charge. |
| 32 | Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. |
| 33 | Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed and including 10mm thick renderingin cement mortar 1:4 to receive, complete all as specified and directed by Engr-in-Charge. |
| 34 | 20mm thick granite (of any type)machine cut laid over 15mm cement screed in cement mortar 1:6 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, complete all as specified and directed by Engr-in-Charge. |
| 35 | 18-20mm thick udaipur green marble stone (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shadecomplete all as specified and directed by Engr-in-Charge. |
| 36 | 60mm thick factory made machine pressed precast concrete coloured interlocking paver blockwith grey cement and pigment, any shape,size and design as approved by Engr-in charge confirming to IS 15658-2006, M-35 grade, complete all as specified and directed by Engr-in-Charge. |
| 37 | M&L for providing 80 mm thick factory made machine pressed precast concrete interlocking coloured tiles with grey cement and pigment of any shape and size confirming to IS 15658-2006, of grade M-40 (compressive strength) of mixed colour complete all as specified and directed by Engr-in-Charge. |
| 38 | Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed by Engr-in-Charge. |
| 39 | 50mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed by Engr-in-Charge. |
| 40 | Plain cement concrete,1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mmthick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed by Engr-in-Charge. Note:- The unit rate include for use of form work (straight or curved). |
| 41 | Anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engr-in-Charge. |
| 42 | Anodised aluminiumdoor shutters, single panel with floor door spring with powder coated aluminium frame of section100x44x 1.5mm and shutter having stile, top rail, lock rail and botton rail of section 44.50x83.50x1.80mm including 5.5mm thick tinted sheet glass ordinary quality including necessary joining cleats, glazing clips, ruber neoprene packing, suitable push and pull plate/handle, 1 No 200mm long aluminium tower bolt, 1 No mortice brass lock 100mm size 4 lever (vertical type), handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc., complete all as specified and as directed by Engr-in-Charge. |
| 43 | Aluminium partition fixed type with frame 100x44x1.5mm including 5.5mm thick sheet glass, necessary joining cleats, glazing clips, ruber neoprene packing anodised aluminum snap beading screws etc complete all as specified and directed by Engr-in-Charge. |
| 44 | Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed by Engr-in-Charge. |
| 45 | Factory made solidpanel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVCchannel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed by Engr-in-Charge. |
| 46 | 35mm thick, 2nd class softwood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed by Engr-in-Charge. |
| 47 | 35mm thick, 2nd class softwood factory made glazed and skeleton shutters,open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges offraming plain, chamfered or rounded, fitted with cut &mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-ISection-8,clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed by Engr-in-Charge. |
| 48 | 30mm thick, 2nd class softwood factory made glazed and skeleton shutters,open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges offraming plain, chamfered or rounded, fitted with cut &mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-ISection-8,clause 8.24 (b) for door shutter supplying and fitted to chowkats, complete all as specified and directed by Engr-in-Charge. |
| 49 | 2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engr-in-Charge. |
| 50 | 6mm thick plywood, grade BWR, type BB, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed by Engr-in-Charge. |
| 51 | 6mm thick plywood, grade BWR, type BB, fixed as in walls with nails to timber frame, complete all as specified and directed by Engr-in-Charge. |
| 52 | 4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed by Engr-in-Charge. |
| 53 | 4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in walls with nails to timber frame, complete all as specified and directed by Engr-in-Charge. |
| 54 | 2nd class softwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed by Engr-in-Charge. |
| 55 | 2nd class softwood, as in scantling and similar work, clean sawn, timber fixed in position, complete all as specified and directed by Engr-in-Charge. |
| 56 | All as per the description of item No. 55 here-in- before but except timber. |
| 57 | 2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed by Engr-in-Charge. |
| 58 | 2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area exc 3 Sqcm but n exc 6 Sqcm complete all as specified and directed by Engr-in-Charge. |
| 59 | 2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area n.exc 3 Sqcmcomplete all as specified and directed by Engr-in-Charge. |
| 60 | 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap with zinc coating of 275, fixed with "L" or "J" type or cranked hook bolts in roofs, walls etc. complete all as specified and directed by Engr-in-Charge. |
| 61 | All as per srl item No-60 here in above but except sheets, complete all as per specified and directed by Engr-in-Charge. |
| 62 | 0.80mm thickplain galvanized mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 complete all as specified and directed by Engr-in-Charge. |
| 63 | Pre-painted galvalume aluminium zinc coating GIbased corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed by Engr-in-Charge. |
| 64 | Pre-painted galvalume aluminium zinc coating GIbased plaind steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed by Engr-in-Charge. |
| 65 | 250mm size mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge. |
| 66 | 150mm long mild steelbarrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed by Engr-in-Charge. |
| 67 | 100mm long mild steelbarrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed by Engr-in-Charge. |
| 68 | 75mm long mild steelbarrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed by Engr-in-Charge. |
| 69 | 75mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engr-in-Charge. |
| 70 | 125mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engr-in-Charge. |
| 71 | 150mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engr-in-Charge. |
| 72 | 100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed by Engr-in-Charge. |
| 73 | 75mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed by Engr-in-Charge. |
| 74 | S & F in repair aluminium (extruded section) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed, complete all as specified and directed by Engr-in-Charge. |
| 75 | S & F in repair 300mm long mild steel ordinary rat tail rod pattern, springs including roller and roller plate fixed to wooden chowkhat, complete all as specified and directed by Engr-in-Charge. |
| 76 | 3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-Charge. |
| 77 | 3mm thick figured glass pin headed typeand glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed by Engr-in-Charge. |
| 78 | 5.50mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares exc 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-Charge. |
| 79 | Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed by Engr-in-Charge. |
| 80 | Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples (fixed in repair), complete all as specified and directed by Engr-in-Charge. |
| 81 | Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed by Engr-in-Charge. |
| 82 | All as per the description of item No. 81 here-in- before but except tubing. |
| 83 | Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed by Engr-in-Charge. |
| 84 | All as per the description of item No. 83 here-in- before but except tubing. |
| 85 | Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all asspecified and directed by Engr-in-Charge. |
| 86 | Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball including dismantlling of existing tank, complete all asspecified and directed by Engr-in-Charge. |
| 87 | S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including PVC (SWR) "P" trap, jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed by Engr-in-Charge. |
| 88 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including "P" or "S" trap, seat cover and fixing bolts, flushing cistern and flush pipe & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed by Engr-in-Charge. |
| 89 | S & F in repair for 125mm size brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe of 15mm diaor union, complete all as specified and directed by Engr-in-Charge. |
| 90 | S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets,complete all as specified and directed by Engr-in-Charge. |
| 91 | S&F in repair vitreous china, wash hand basin, flat back of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm dia PVC waste fitting, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed by Engr-in-Charge. |
| 92 | S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm,complete all as specified and directed by Engr-in-Charge. |
| 93 | S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in-Charge. |
| 94 | S & F in repair 32 mm dia waste coupling of PTMT (half or full threaded) (minimum weigh 45 gms) complete all as specified. |
| 95 | S&F in repair 20 mmBall valve high pressureof PTMT with epoxy coated Aluminiumrod & high density plastic ball screwed for iron pipe and fixed any colour high pressure screwed for iron pipe and fixed. (Minimum weight 210gms)complete all as specified and directed by Engr-in-Charge. |
| 96 | S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed by Engr-in-Charge. |
| 97 | S&F in repair 15mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed, complete all as specified and directed by Engr-in-Charge. |
| 98 | S & F in repair 15mm dia pillar taps, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered "Hot" and "Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge. |
| 99 | S&F in repair 15 mm borebrass CP mixer for mixing hot and cold waterscrewed down for iron pipe and fixeds, complete all as specified and directed by Engr-in-Charge. |
| 100 | S & Fin repair 15mm bore bib tap, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed by Engr-in-Charge. |
| 101 | S&F in repairs 15mm bore stop valves, fancy type, chromium plated with long long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed by Engr-in-Charge. |
| 102 | S & F in repair 110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engr-in-Charge. |
| 103 | S & F in repair 75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engr-in-Charge. |
| 104 | 110mm bore dia PVC (SWR) bends, complete all as specified and directed by Engr-in-Charge. |
| 105 | 75mm bore dia PVC (SWR) bends, complete all as specified and directed by Engr-in-Charge. |
| 106 | S&F in repairs 75mm dia outlet PVC (SWR) multi floor trap with grating including jointing with solvent cement, complete all as specified and directed by Engr-in-Charge. |
| 107 | Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, hold fast and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form workcomplete all as specified and directed by Engr-in-Charge. |
| 108 | Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed by Engr-in-Charge. |
| 109 | Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over chalk whiting, on plastered surfaces prepara-tory to distempering, complete all as specified and directed by Engr-in-Charge. |
| 110 | Preparation of new CGI/PGI steel surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over a coating of mordant solution including washing the surfaces, complete all as specified and directed by Engr-in-Charge. |
| 111 | Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed by Engr-in-Charge. |
| 112 | Preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash on wall, complete all as specified and directed by Engr-in-Charge. |
| 113 | All as per item No 112 above but applying one coat of white wash on ceiling, complete all as specified and directed by Engr-in-Charge. |
| 114 | All as per item No 112 above but applying one coat of white or tinted oil bound distemper on wall, complete all as specified and directed by Engr-in-Charge. |
| 115 | All as per item No 112 above but applying one coat of cement based paint on wall, complete all as specified and directed by Engr-in-Charge. NOTE: Work to be carried upto 10m height. |
| 116 | All as per item No 01 above but applying one coat of weather proof exterior acrylic emulsion in camouflage pattern on wall, complete all as specified and directed by Engr-in-Charge.NOTE: Work to be carried upto 10m height. |
| 117 | Complete removal of existing treatment from external surfaces of walls by wire brushing and washing down and stopping of surfaces and preparation of surfaces by laying with wall care putty as reqd to obtain smooth and even surface and then applying two coats of white or tinted oil bound distemper, complete all as specified and directed by Engr-in-Charge. |
| 118 | Preparation of old painted wooden surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge. |
| 119 | Preparation of old painted GI/steel surfaces of any description not otherwise described over 10cm width or girth as in roof and applying one coat of synthetic enamel paint complete all specified and directed by Engr-in-Charge. NOTE: Work to be carried upto 10m height. |
| 120 | All as per item No 119 above but applying two coats of synthetic enamel paint complete all as specified and directed by Engr-in-Charge. |
| 121 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixturesuch as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody for reuse if serviceable or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engr-in-Charge. |
| 122 | Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable maintaining colour coding (Phase- Red/yellow/Blue, Neutral- Black) and 1.5 sqmm PVCinsulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit mediumgrade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specifiedand directed by Engr-in-Charge. |
| 123 | All as per srl item No 122 here in above but for one 3 pin 5A socket outlet on independent board controlled by one switch, complete all as specified and directed by Engr-in-Charge. |
| 124 | All as per srl item No 122 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specified and directed by Engr-in-Charge. |
| 125 | All as per serial item No 122 here-in-before but for 3 pin 15 Amps socket outlet on independent board with 2.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specified and directed by Engr-in-Charge. |
| 126 | Concealed Point wiring complete with 1.5 sqmm 1100 graded PVC FRLS (Multistrand) insulated unsheathed copper conductor single core multi strand flexible cable maintaining colour coding (Phase- Red/yellow/Blue, Neutral- Black), PVC conduit not less than 20mm dia concealed, including cutting chases, finishing of slots by means of cement mortar 1:3 making good to existing surface of the wall and touching with three coats ofexisting colour of wall and making good disturbed surface complete sunk in pressed steel terminal boxes of required size not less than 1.6mm thick factory made and factory painted with top cover 3mm thick plastic laminated sheet fixed with brass screw and washers with all accessories including single core multistranded copper conductor 1.5 sqmm size cable (green colour) as earth continuity wire connected to common earth dolly to modular concealed box and white cover plate of required nos and required sizefor housing switches, sockets etc for one light / fan/ bell point controlled by one switch one way and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specifiedand directed by Engr-in-Charge. |
| 127 | All as per srl item No 126 here in above but for one 3 pin 5A socket outlet independent controlled by one switch, complete all as specifiedand directed by Engr-in-Charge. |
| 128 | All as per srl item No 126 here in above but for one 5A socket outlet on the same board controlled by one switch, complete all as specifiedand directed by Engr-in-Charge. |
| 129 | All as per srl item No 126 here in above but for one 3 pin 15 Amps socket outlet independentwith 2.5 sqmm PVCinsulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead, complete all as specifiedand directed by Engr-in-Charge. |
| 130 | Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/ Polycarbonate, isolated body, complete all as specified and directed by Engr-in-Charge. |
| 131 | Switch piano flush button types 6 Amp, single pole, one way complete all as specified and directed by Engr-in-Charge. |
| 132 | Switch socket combination 2 in 1, 3 pin, 5 Amp flush type, universal, complete all as specified and directed by Engr-in-Charge. |
| 133 | Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp, flush type universal, complete all as specified and directed by Engr-in-Charge. |
| 134 | Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular suitable for batten fittings, complete all as specified and directed by Engr-in-Charge. |
| 135 | Bell push, flush type, 5 Amp, complete all as specified and directed by Engr-in-Charge. |
| 136 | S&F in repair Call bell , ding dong AC single phase, 230 volts 50 Hz including wooden/ PVC board of suitable size, connecting and testing, complete all as specified and directed by Engr-in-Charge. |
| 137 | Fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically all as required at site or directed by Engr-in-Charge. |
| 138 | S&F in repair Modular switch 1 way 6A,1 module all as specified and directed by Engr-in-Charge. |
| 139 | S&F in repair Modular switch 1 way 16A,1 module all as specified and directed by Engr-in-Charge. |
| 140 | S&F in repair Modular socket, 6A - 2/3 pin combined 2 modules all as specified and directed by Engr-in-Charge. |
| 141 | S&F in repair Modular socket 6/16A,2/3 pin, combined 2 module all as specified and directed by Engr-in-Charge. |
| 142 | S&F in repair Modular fan step regulator, 120W - 2 modular all as specified and directed by Engr-in-Charge. |
| 143 | S&F in repair White cover plate with frame, 2 module all as specified and directed by Engr-in-Charge. |
| 144 | S&F in repair White cover plate with frame, 4 module all as specified and directed by Engr-in-Charge. |
| 145 | S&F in repair White cover plate with frame, 6 module all as specified and directed by Engr-in-Charge. |
| 146 | S&F in repair, Plug top 3 pin 5/6 amps 230 volts, complete all as specified and directed by Engr-in-Charge. |
| 147 | S&F in repair Plug top 3 pin 15/16 amps 230 volts, complete all as specified and directed by Engr-in-Charge. |
| 148 | S&F in repair PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified and directed by Engr-in-Charge. |
| 149 | S&F in repair PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified and directed by Engr-in-Charge. |
| 150 | S&F in repair LED 9 watt pin type bulb, complete all as specified and directed by Engr-in-Charge. |
| 151 | LED light fitting 1 x 10 Watt ,2 " long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use packincludingLED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with threecore twisted flexible copper conductor cable with suitable size LED tube including taking out old, complete all as specified and directed by Engr-in-Charge. |
| 152 | LED light fitting 1 x 18 Watt ,4 " long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use packincludingLED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with threecore twisted flexible copper conductor cable with suitable size LED tube including taking out old, complete all as specified and directed by Engr-in-Charge. |
| 153 | S&F in repair of LED light fitting 1 x 18 Watt ,4 " long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use packincludingLED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with threecore twisted flexible copper conductor cable with suitable size LED tube including taking out old, complete all as specified and directed by Engr-in-Charge. |
| 154 | S&F in repair of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engr-in-Charge. |
| 155 | S&F in repair LED light fitting 12watt 220 volts AC round shape/ square shape recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. |
| 156 | Supply & fixing in repair MCB Distribution board , 240 volts single pole andneutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed by Engr-in-Charge. |
| 157 | Supply & fixing in repair MCB Distribution board , 240 volts single pole andneutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 8 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed by Engr-in-Charge. |
| 158 | Supply & fixing in repair MCB distribution board , 240 volts single pole andneutral, double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 12 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed by Engr-in-Charge. |
| 159 | S&F in repair double door type vertical type TPN DB 4 Way ,240Vwith 200A busbar , with metalic double door type IP 43 IK 09 protectionsuitable for housing MCCB"s all as specified and directed by Engr-in-Charge. NOTE :- DBs shall be concealed in wall where ever posible including making good the surface to match with surrounding. |
| 160 | S&F in repair MCCB FP 63 Amps,16KA,415 volt, complete all as specified and directed by Engr-in-Charge. |
| 161 | Supply & fixing in replacement MCB single pole 240 volts, "B" curve of rating 6 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engr-in-Charge. |
| 162 | Supply & fixing in replacement MCB single pole 240 volts, "B" curve of rating 10 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engr-in-Charge. |
| 163 | Supply & fixing in replacement MCB single pole 240 volts, "B" curve of rating 16 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engr-in-Charge. |
| 164 | Supply & fixing in replacement MCB single pole 240 volts, "B" curve of rating 25 amps, as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed by Engr-in-Charge. |
| 165 | Supply & fixing in replacement MCB single pole neutral (SPN) 32 Amps 240 Volts, "C" curve,with rupturing capacity 10 KA, complete as specified and directed by Engr-in-Charge. |
| 166 | Supply & fixing in replacement MCB single pole neutral (SPN) 40 Amps 240 Volts with rupturing capacity 10 KA, complete as specified and directed by Engr-in-Charge. |
| 167 | Supply & fixing in replacement MCB TPN 415 volts, 40Amps "C" Curve 10 kA capacity, complete all as specified and directed by Engr-in-Charge. |
| 168 | S&F in repair for Sub main wiring with two singlecore PVC insulated flexible copper conductor cable of size 6.0 sqmm and one single core PVCinsulated flexible copper conductor cable green colour of size 6.0 sqmm as earth lead in & includingPVC casing capping medium grade2mm thickness ISI markedincl taking down old unsv, complete all as required at site or directed by Engr-in-Charge. |
| 169 | Supply and laying in repair service cable 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed 16 sqmm 2 Core nominal cross section complete all as specified and directed by Engr-in-Charge. |
| 170 | Supply & fix in repair Rigid non-metallicgrade PVC conduit of size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and directed by Engr-in-Charge. |
| 171 | Supply & fix in repair medium gradePVC casing and cappingof size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and directed by Engr-in-Charge. |
| 172 | Disconnectiong, taking down, strip opening, cleaning all parts and packing of exhaust fan of any make and size & greasing ball bearing with specified quality grease & recommisioning the same including making new electric flexible wire connection, complete all as specified and directed by Engr-in-Charge. NOTE: Replacement of spare parts, rewinding, painting etc to be measured and paid separately. |
| 173 | Disconnectiong, taking down, strip opening, cleaning all parts and packing of ceiling fan of any make and size & greasing ball bearing with specified quality grease & recommisioning the sa,e including making new electric flexible wire connection, complete all as specified and directed by Engr-in-Charge. NOTE: Replacement of spare parts, rewinding, painting etc to be measured and paid separately. |
| 174 | Painting of ceiling fans complete of any size and make, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. including marking MES unit name at bottom of the fan with black paint, complete all as specified and directed by Engr-in-Charge. |
| 175 | Painting of exhaust/air circulated fans complete of any size and make, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. including marking MES unit name at bottom of the fan with black paint, complete all as specified and directed by Engr-in-Charge. |
| 176 | Replacement of short circuit/over-heated windings from starter of ceiling fan of any make having 1200/1400mm sweep with matching guage & turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking, heating, drying, cleaning fan bearing/bushes, greasing, oiling and reassembling of fan with testing etc, complete all as specified and directed by Engr-in-Charge. |
| 177 | Replacement of short circuit/over-heated windings from starter of exhaust fan of any make having 300mm/350mm/450mm sweep with matching guage & turns of super enamelled copper winding wire complete with leathered paper, glass sleeves, varnishing, baking, heating, drying, cleaning fan bearing/bushes, greasing, oiling and reassembling of fan with testing etc, complete all as specified and directed by Engr-in-Charge. |
| 178 | Gun metal bush with suitable size for ceiling fan any make, any size and any sweep, complete all as specified and directed by Engr-in-Charge. |
| 179 | Ball bearing suitable for 1200mm/1400mm sweep ceiling fan of any size any make, complete all as specified and directed by Engr-in-Charge. |
| 180 | Canopy (top & bottom) of ceiling fans of any make/size with matching colour, complete all as specified and directed by Engr-in-Charge. |
| 181 | Rubber reel, heavy duty for hanging ceiling fans of any make/size with nuts, bolts, split pins etc., complete all as specified and directed by Engr-in-Charge. |
| 182 | Connector block of suitable size and approved quality for ceiling fans, complete all as specified and directed by Engr-in-Charge. |
| 183 | Capacitor 2.5 mfdAC 230 volts 50 Hz, complete all as specified and directed by Engr-in-Charge. |
| 184 | Fan blade ISI make, made of aluminium alloy duly painted and air dynamic angled including provision of screws for fixing purpose for 1200/1400mm sweep ceiling fans, complete all as specified and directed by Engr-in-Charge. |
| 185 | Hanger clamp assembly of down rod for hanging of ceiling fanof ceiling fans with nuts, bolts, split pins etc, complete all as specified and directed by Engr-in-Charge. |
| 186 | Ball bearing suitable for 300mm/450mm sweep exhaust fan, complete all as specified and directed by Engr-in-Charge. |
| 187 | Capacitor 3.15 mfdAC 230 volts 50 Hz, complete all as specified and directed by Engr-in-Charge. |
| 188 | Exhaust fan blade, heavy duty 300/380mm sweep complete all as specified and directed by Engr-in-Charge. |
| 189 | Exhaust fan blade, heavy duty 450/600mm sweep complete all as specified and directed by Engr-in-Charge. |
| 190 | Taking down water storage heater of capacity 25/35/50 ltr from the site and opening base plate assy and removing all sludge and scaling from the inner tank and refixing the the base plate assy with and including minor spares such rubber gasket, piece of wire etc, complete all as specified and directed by Engr-in-Charge. |
| 191 | M&L for replacement of Heating element AC 230 Volt of rating 1500W ISI mark as per existing any type, complete all as specified and directed by Engr-in-Charge. |
| 192 | M&L for replacement of Heating element AC 230 Volt of rating 2000W ISI mark as per existing any type, complete all as specified and directed by Engr-in-Charge. |
| 193 | M&L for replacement of Thermostat switch AC 230 Volt adjustable range from 0-90 degree Celsius, complete all as specified and directed by Engr-in-Charge. |
| 194 | M&L for replacement of flexible PVC connection pipe heavy duty suitable for hot waterto bear the temperature 100 degree Celsius with out let and inlet connection brass adaptor and PVC washer having size 450 mm long 15 mm nominal dia complete all as specified and directed by Engr-in-Charge. |
| 195 | M&L for replacement of indicator lamp round/square in shape suitable for 25-50 ltr storage type water heater as per sample 230 volt, complete all as specified and directed by Engr-in-Charge. |
| 196 | M&L for replacement of auto-cut switch suitable for geyser 25-50 ltrs 230 volts AC all as per sample, complete all as specified and directed by Engr-in-Charge. |
| 197 | M&L for replacement of geyser assembly suitable for geyser 25-50 ltrs 230 volts AC all as per sample, complete all as specified and directed by Engr-in-Charge. |
| 198 | M&L for replacement of inner tank assy made of copper suitable for 25 ltr storage type water heaterwith and including nuts, bolts and washer and fusible plug, complete all as specified and directed by Engr-in-Charge. |
| 199 | M&L for replacement of inner tank assy made of copper suitable for 35 ltr storage type water heaterwith and including nuts, bolts and washer and fusible plug, complete all as specified and directed by Engr-in-Charge. |
| 200 | M&L for replacement of inner tank assy made of copper suitable for 50 ltr storage type water heaterwith and including nuts, bolts and washer and fusible plug, complete all as specified and directed by Engr-in-Charge. |
| 201 | M&L for replacement of glass woolfor insulation purpose in any make and any capacity storage type water heater complete all as specified and directed by Engr-in-Charge. |
| 202 | M&L for replacement of outer body including upper and lower cover and inspection plate made of MS sheet duly painted with super enameled synthetic paint over a coat of steel primer suitable for 25 Ltr storage type water heater, complete all as specified and directed by Engr-in-Charge. |
| 203 | M&L for replacement of outer body including upper and lower cover and inspection plate made of MS sheet duly painted with super enameled synthetic paint over a coat of steel primer suitable for 35 Ltr storage type water heater, complete all as specified and directed by Engr-in-Charge. |
| 204 | M&L for replacement of outer body including upper and lower cover and inspection plate made of MS sheet duly painted with super enameled synthetic paint over a coat of steel primer suitable for 50 Ltr storage type water heater, complete all as specified and directed by Engr-in-Charge. |
| 205 | M&L for replacement of three core cable 1100 volt grade having size 40/0.0076 copper conductor multi stranded, complete all as specified and directed by Engr-in-Charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
