Military Engineer Services-MES has published Tender For Addition / Alteration In Buildings Of Auto Fire Suppression System School Palam Under Ge (Af) Palam Delhi Cantt-10. Submission Date for this Tender is 12-05-2023. Fire Suppression System Tenders in Delhi Delhi. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Dismantling of existing roof tiles including roof treatment, plaster of any thickness etc and removing the debris from site to outside MoD land. |
| 2 | M&L for 10 mm thick screed bed in cement mortar 1:4 on concrete surfaces of roof mixed with water proofing compound including finishing surface even and smooth without using extra cement upto 4 storey building complete all as specified.Note :- Water proofing compound shall be measured & paid separately as supply only. |
| 3 | Supply only liquidwater proofing compound. |
| 4 | M&L for 50mm thick (average thickness) cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in roof padding to maintain slope all as specified and directed by Engineer-in-Charge. |
| 5 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (weight not less than 160 gms/sqm)land on primed surface by forced application method over 85/25 industrial bituminous coat @ 1.20Kg/Sqm over bituminous primer @ 0.30 ltr/sqm on newly plastered surface after clean and dry the roof surface.APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc.Membrane bonded completely to the substrate & overlaps are then scaled/fused by flame all as directed. (Note :(i)Water ponding test atleast for 72 Hours shall be carried out after final layer of roof treatment by the contractor. (ii)The contractor shall submit 10 years warranty against the roof treatment and security deposit @ 2% for 10 years from the date of completion of work. (iii)The contractor shall submit test certificate of APP Membrane (iv)The work shall be carried out by authorised applicator of manufacturer.) complete all as specified & as directed by Engr-in-charge. |
| 6 | M&L for factory made cement concrete tiles 250mm x 250mm x 25mm thick, machine pressed, set & pointed in neat cement slurry with grey cement and no pigment on roofover and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified |
| 7 | S&F forsolid PVC wall lining consisting of 5mm thickwood grain printed PVC sheet inclusive of solvent cement and fixing at site on 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing. |
| 8 | M&L for false ceiling of non asbestos fibre cement building boardsfixed or laid/ inserted to GI framework with screwsincluding Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with hangers 6 mm dia. G.I (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete including cutting holes and making good for main joints, suspenders to roof slab or roof trusses/ purlins/ rafters etc all as per approved and directed by Engr-in-Charge. |
| 9 | Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil. |
| 10 | M&L for hardcore gauge n.exc 63mm of broken stone or boulders deposited, spread and levelled in layers not exc 75mm thick, watered and well rammed to a true surface complete all as specified. |
| 11 | M&L for 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone agreegate as in hardstanding including making joints at proper interval duly filled with sealing compound grade "A" and necessary form work. |
| 12 | S& F forfactory made machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Gradelaid over 30 mm thick sand cushioning. |
| 13 | M&L for cement concrete 1:3:6 type C-1 using20 mm graded stone aggregate as in lintels upto1.5m clear span,cills,steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering,slightly rounded or chamfered angles and throating as directed. |
| 14 | S&F for 18mm thick (12 ply) veneered decorative plywood, grade 1 (with BWR resin) with 0.9mm thick decorative laminate on both faces with adhesive as in cupboard, show case, partition, shutter and shelves etc fixed with screws complete including necessary hinges, magnet cacher and handle fixed on wall or floor complete all as specified anddirected by Engr-in-Charge. |
| 15 | M&L for brick work with sub class "B" bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 all as specified. |
| 16 | Taking down cement or cement lime plasteron brick/ stone or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc upto 4th storey building including removing the debris from site to outside MoD land. |
| 17 | M&L for 10 mm thick cementplaster on fair faces of brick work or concrete surfaces of walls in cement mortar 1:6 including finishing surfaceeven and smooth without usingextra cement . |
| 18 | M&L for 10 mm thick cementplaster on fair faces of brick work or concrete surfaces of walls in cement mortar 1:4 including finishing surfaceeven and fair without usingextra cementbut with water proofing compound as per manufacturer"s instructions including necessaryscaffolding and safety arrangements. (Note : WPC will be measured and paid separately). |
| 19 | M&Lfor 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:3 in ceilings including finishing surfaceeven and smooth without usingextra cement . |
| 20 | M&lfortwocoats ofoilbounddistemperovera coatof primer using roller over 1 mm thick (avg) wall care puttyincluding necessary scaffolding and preparationof newlyplasteredsurfaces on walls/ceiling all as specified . |
| 21 | M&L for prepration of newly plastered surface and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade as new work (two coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm as per specified and directed. |
| 22 | M&L for vitrified tiles light shade8 to 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15mm thick screed bed in cement mortar 1:6. |
| 23 | All as per item No 22 above but on vertical surface as wall, dado, skirting etc including 10 mm thick rendering in cement mortar 1: 4. |
| 24 | S&F for aluminium anodised colour powder coated (thickness of powder coating not less than 50 micron) door frame and shutter single or double leaf, glazed with pre laminated particle board, exterior grade, panels fabricated including aluminium powder coated beading, rubber gasket and packing materials, drilling in existing wall and thrust boltof suitable size complete comprising the following:- (a) Door frame section 101.60mm x44.45mmx1.93 mm. (b) Door shutter vertical Style of size 85mmx44.45mmx2 mm. (c) Door shutter top style section 95.25mmx44.45mmx2.00 mm. (d) Aluminium coloured powder coated middle lock rail/bottom rail section 125mmx44.45mmx1.93mm. (e) Aluminium coloured powder coated tower bolt 02 Nos in each shutter 200 mm long. (f) Aluminium coloured powder coated handle 02 Nos in each shutter 150 mm long. (g) Door floor spring ISI Marked. (h) Six lever mortice lock brass in each door. (j) 12 mm thick partical board (pre-laminated both face) exterior grade ISI Marked (k) 5mm thick tinted glass/plain glass(Coloured) |
| 25 | S&F for aluminium anodised colour powder coated (thickness of powder coating not less than 50 micron)window frame with shutter of three track using Jindal section No 20832 (92mmx31.75mmx1.50mm) or its equivalentfixed with thrust bolt in walls by drilling and sliding shutter of section No 20844 (40mmx18mmx1.29mm) including 4 mm thick tinted glass fixed with rubber beading and bushes complete in two track and stainless steel wire cloth of 0.36 mm nominal dia and average width of aperture 1.40mm fixed with screw and aluminium beading complete all as specified and as directed by Engr-in-Charge. |
| 26 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area not exc. 1.5 sqm each. |
| 27 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area exc. 1.5 sqm but not exc. 4.0 sqm each. |
| 28 | S&F for 35mm thick factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressuretreated of second class hard wood. |
| 29 | S&F for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to grade Fe-290 Gde-E-165 including welding hold fast, hinges etc to frame all as specified. |
| 30 | S&F for 125mm long extruded anodised aluminumalloy handlefabricated type fixed with flat head SS screw. |
| 31 | S&F for 150mm long anodised aluminum barrel tower bolt of extruded aluminium section fixed with flat head SS screw. |
| 32 | S&F for aluminum alloy sliding door bolt 300mm long with hasp, staple (bolt type) adnd fixing clips of sheets, cast of exctruded sections and fiing bolts or extruded section and all as specified. |
| 33 | M&L for preparation of newly surfaces of wood of any description not otherwise described over 10cm width or girth overand applying two coats of synthetic enamel paint over a coat of pink primer all as specified. |
| 34 | M&L for preparation of newly surfaces of steel of any description not otherwise described over 10cm width or girthand applying two coats of synthetic enamel paint over a coat of pink primer all as specified. |
| 35 | M&L for complete removal of existing treatment on walls, removal of nails etc and applying two coats of oil bound distemper white or coloured over a coat of approved primerby rollers over 1mm thick (avg) wall care putty complete all as specified & directed by Engineer-in-Charge. |
| 36 | M&L for complete removal of existing treatment on walls, removal of nails etc andapplying two coats of exterior emulsion paint 100% acrilic of approved colour or white over a coat of approved primerby rollers over 1mm thick (avg) wall care putty complete all as specified & directed by Engineer-in-Charge. |
| 37 | M&L for mirror polishing on marble /granite/kota stone where ever required to give high glossy finish complete. |
| 38 | M & L for gunniting work to RCC beam, column, lintel, pardi, railing, slabs, side walls etc by removing loose, disturbed or disintegrated old concrete surfaces, cleaning thoroughly exposed reinforcement by sand blasting using suitable pump and applying one coat of anti corrosive paint to the exposed reinforcement, S&F welded wire mesh fabric or wire net of size100mm x 100 mm x 3 mm dia of weight not less than 1.37 Kg/Sqm and tied to existing reinforcement with 22 guage mild steel (annealed)binding wire and applying gunniting pressure 2.00/ 2.50 Kg/Sqm with admixture 1 part of cement and 3 part of sandwith average thickness 40mm and making the surface even including rendering 15 mm thick in cement mortar 1:4 mixed with water proofing compound @2% by weight of cement on concrete surface including finishing the surfaces even and smooth without using extra cement and providing necessary scaffolding and safety arrangement including removing the debris from site to outside MoD land complete all as specified and directed. (Note :-The finish of the surfaces to be matched with the existing surface.WPC shall be measured & paid separately as supply only). |
| 39 | S&F for rolled mild steel in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)conforming to Fe 410 -W (GdeE- 250) quality A including repairing the hole with PCC 1:2:4 type B-1 and making good with cement plaster in 1:4 complete. |
| 40 | M & L for 75mm thick cement concrete 1:3:6 type C-2 using 20mm graded stone aggregate as in plinth protection including finishing even and smooth surface without using extra cement and making joints 12 mm wide to the full depth of concrete at every 3 metres interval and at every change of direction and filling the same with bitumen (85/25 grade) sand mastic complete all as specified. |
| 41 | Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing including removing the debris from site to outside MoD land. |
| 42 | M&L for joint free coloured glazed ceramic tiles as in vertical surfaces of size 300x200x7mm/ 450x300x7mm thick first quality, set and jointed in cement slurry and pointed in white or coloured cement to match the tiles laid over & including 15mm thick rendering in cement mortar 1:4 all as directed and specified. |
| 43 | M&L for25mm thick cement concrete 1:2:4, type B-1 (20mm graded stone aggregate) as in floor including finishing surface even and smooth with using extra cement all as specified. |
| 44 | M&L for joint free non skid coloured ceramic tiles (first quality) 7 to 8mm thick (squre or rectangular)area of each tile not exc 0.11sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over & including 15mm thick screed bed in cement mortar 1:6. |
| 45 | M&L for GI tubing 15mm bore `medium grade`with all fittings and fixed complete to walls and ceilings or laid in floors etc complete. |
| 46 | M&L for GI tubing 20mm bore `medium grade`with all fittings and fixed complete to walls and ceilings or laid in floors etc complete. |
| 47 | S&F for sink with drainage board made out of stainless steel 1mm thick, kitchen or laboratory with plugs, washes and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size 915X460mm with bowl size 410X330X160mm all as specified. |
| 48 | S&F for 15 mm dia bib tap, chromium plated, fancy type, long body screwed down, screwed for iron pipe or for brass ferrule and fixed. |
| 49 | S&F in repair cast iron floor trap with CP grating multi outlet including jointing to wastepipe withrun lead, dia of outlet 75mm set in cement concrete type B1 (1:2:4) complete all as specified. |
| 50 | S&F for PVC waste pipe flexible type 25 mm dia suitable for couplings 32 mm & 40 mm dia and 610mm long. |
| 51 | S & F for factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete with glazing bars dovetailed or welded including 4mm thick sheet glass ordinary quality fixed with oil putty complete all as specified and as directed |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
