|
| 1 | Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 2 | All kinds of soil |
| 3 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : |
| 4 | 300x16 mm |
| 5 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 6 | 300x16 mm |
| 7 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 8 | 300x10 mm |
| 9 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 10 | Providing and fixing to existing door frames. |
| 11 | 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. |
| 12 | 12 mm cement plaster of mix : |
| 13 | 1:6 (1 cement: 6 coarse sand) |
| 14 | 15 mm cement plaster on rough side of single or half brick wall of mix: |
| 15 | 1:6 (1 cement: 6 coarse sand) |
| 16 | Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. |
| 17 | Two or more coats on new work |
| 18 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 19 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. |
| 20 | With cement mortar 1:4 (1cement: 4 coarse sand) |
| 21 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : |
| 22 | Old work (one or more coats) |
| 23 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 24 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 25 | One or more coats on old work |
| 26 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 27 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 28 | 10 litre capacity - White |
| 29 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 30 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 31 | 15 mm nominal bore |
| 32 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 33 | 15mm nominal bore, 86 mm long, weighing not less than 88 gms |
| 34 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 35 | 15 mm nominal bore with 45 cm length |
| 36 | Add 31.27% as cost index on DSR 2016 on Item No. 01 to 20.01 of Rs. 362020/- |
| 37 | Less 9.50% as per Delhi Govt. Circular on DSR 2016+C.I. i.e. on Rs. 475224/- |
