}

Tender For Up Gradation Of Sub Centre As Su Swasthya Kendra At Melli Under Rambi Bphc Kalimpong I, Gta, kalimpong-West Bengal

Gorkhaland Territorial Administration-GTA has published Tender For Up Gradation Of Sub Centre As Su Swasthya Kendra At Melli Under Rambi Bphc Kalimpong I, Gta. Submission Date for this Tender is 17-03-2023. Building Repair Tenders in kalimpong West Bengal. Bidders can get complete Tender details and download the document.




Tender Notice

36620695
Tender For Up Gradation Of Sub Centre As Su Swasthya Kendra At Melli Under Rambi Bphc Kalimpong I, Gta
Open Tender
Indian
West Bengal
kalimpong
17-03-2023

Tender Details

Up Gradation Of Sub Centre As Su Swasthya Kendra At Melli Under Rambi Bphc Kalimpong I, Gta

Key Value

Document Fees
INR 2000 /-
EMD
INR 22172.0 /-
Tender Value
INR 11.08 Lakhs /-

BOQ Items

Up gradation of Sub Centre as Sub Swasthya Kendra at Melli under Rambi BPHC, Kalimpong I, GTA
Sl. No. Item Description
1Ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement if any, in Ground Floor as per revelent IS codes . Upto 4th Floor
2Ordinary cement concrete (mix 1:2:4) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement if any, in Ground Floor as per revelent IS codesUpto 4th Floor
3Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rodsinitial straightening and removal of loose rust (if necessary), cutting to requisite length hooking and bending to correct shape placing in proper position and binding with16G black annealed wire at every intersectionas per drawing and direction. (a) For works in foundation and upto roof of top floor/upto 4 m
4Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with requirbeams,columns,lintels curved or straight including fitting , fixing and striking out after completion of works(upto roof of ground ground floor) 25mm to 30mm thick wooden shuttering as per decision & direction of Engineer-In-Charge
5125 mm thick brick work with 1st class bricks in cement mortar (4:1) in ground floor Upto 4th floor
6Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (b) 20 mm thick plaster
7(ii) With 1:4 cement mortar (b) 15 mm thick plaster
8Supplying and laying true to line and level vitrified tiles of approved brand(size not less than 600mmx600mmx10mm thk) in floor, skirting etc. set in 20mm sand cement mortar(1:4) and 2mm thk cement slurry back side of tiles using cement @ 2.91kg/m2 or using polymerised adhesive(6mm thk layer applied directly over finished artificial stone floor/mosiac etc without any backing course) laid after application slurry using 1.75kg of cement per m2 below mortar only, joints grouted with admixture of white cemet and colouring pigment to match with colour of tiles/epoxy groutmaterials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete true to materials, labour and all other incidential charges complete true to manufacturer"s specification and direction of Engineer-In-Charge.(White cement, synthetic adhesive and grout materials to be supplied by the contractor)
9Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.
10Wood works in doors and windows frames fitted and fixed in position including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and MS clamps. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak
11Panel shutters of doors and windows as per design (each panel consisting of single plank without joint) including fitting and fixing the same in position but excluding the cost of hinges and other fittings. In ground floor (a) 35mm thick shutters (single leaf)
12Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. In ground floor.(i) 32 mm thick
13Glazed shutters of doors, windows, fan light, clerestory windows etc. as per design (with ordinary glass of 7.4kg./sq.m. 3mm. Thick) fitted with putty bed and teak wood bead and nails including fitting and fixing shutter in position but excluding the cost of hinges and other fittings. cost of glass, putty, wooded beads etc.will be paid separately. In ground floor. 35mm thick shutters. Upto 4th Floor Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak
14Supplying, fitting and fixing M.S. clamps for fitting doors & windows framesmade offlat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. 40mm x 6mm, 250mm long
15Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (viii) 100mm. X 75mm. X 3.50mm.
1675mm x 60mm x 3.15mm
17Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod) vii) 150mm grip x 12 mm dia rod
18iii) 100mm grip x 12 mm dia rod
19Anodised aluminium skeleton bolt of approved quality manufactured from extruded section confirming to IS specification (IS 204/74) fitted and fixed with cadmium plated screws: (vi) 450mm long x 12mm dia. bolt.
20Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (v) 150mm long x 12mm dia. bolt.
21MS or WI ornamental grill of approved design joints continously welded with MS , WI, flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs . (i) Grill weighing above 10 Kg./sq.mtr and up to 16 kg./sq. mtr.
22Supplying fitting fixing UPVC pipes A-Type and confirming to IS:13592-1992 with all necessary clamps,nails including making hole in the wall floor etc. cutting trenches in any soil through masonry concrerte structure etc. if necessary and mending good damages including joining with jointing materials(Spun Yarn, VAlamoid/Bitumen/M-Seal etc) complete. Page noUPVC Pipes:(ii) 110mm Dia
23Priming one coat on timber or plastered or on steel or other metal surface with synthetic enamel / oil bound primer of approved quality including smoothening surface by sand papering etc.
24Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface if necessary. (a) On timber or plastered surface With super gloss (hi gloss) / Two coats
25Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer"s specification and as per direction of the EIC. (In Ground Floor) Two coats i) Water based interior grade Acrylic Primer
26Applying Exterior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly, complete as per manufacturer"s specification and as per direction of EIC. Two coats i) Water based interior grade Acrylic Primer
27Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer"s specification)including cleaning and smoothning of surface. Two Coats
28Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. a) Normal Acrylic Emulsion
29Upto 4th Floor
30M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. i) For roof truss works
31M.S. structural works in roof trusses with tubular sections conforming to IS: 806-1968 & IS: 1161- 1998 cnnected to one another with bracket, gusset cleats as per design, direction of Engineer-in-charge complete including cutting to requisite size, fabrication with necessary metal arc welding conforming to IS: 816- 1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour reqired for the work including all incidental chages such as electricity charges, labour insurance charges etc.
32Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor)
33Galvanised iron sheet eaves gutter fitted and fixed with necessary 50mm x 6mm MS flat bar clamps bent to design, bolts, nuts, washers etc. complete. Eaves gutter made of 0.63mm sheet. (b) 300 mm wide gutter
34Galvanised iron sheet ridging fittedwith necessary bolts,screws, washers etc. complete. (225mm end lap) 450mm lapping each way . ( c ) With 0.80mm sheet
35Holding down bolt with nut 100mmx100mmx6mm plate washer at bottom fitted and fixed complete by packing the hole by cementconcrete or cement ground as directed.ii) 20mm doa bolt a) 450 mm long.
36Wooden eaves board as per design fitted and fixed complete.Ornamental eaves board (Badam/Gamar/Champ/Hallak) (a) 19mm thk
37P.V.C- False Ceiling : Providing False Ceiling made with framework of steel tube of 40mm x 20mm of not less than 18 gauge,the long and cross section will be welded with each other 1000mm to 1200mm apart the entire framework will be fixed in wall using rawlplug or gutties or screws etc. and suspended from ceiling with M.S flat 19mmx3mm as necessary,the entire frame will be painted with red oxide. PRINTED LAMINATED P.V.C Section 150mm x 12mmx 1.00mm (+/- 0.01mm) of approved quality and colour will be fixed on the frame so that the entire framework will not be visible from below P.V.C Section will be fixed with the frame with the help of self tapping steel screws including all materials and labour charges including fitting,fixing the same and hoisting including mending the damages in all respect and cost of paint as required as per direction of Engineer-in-Charge
38SANITARY AND PLUMBING WORKS Labour for fitting and fixing GI pipes above ground (concealed) in structures with holder bats clamps including cost of jointing materials, holder bat clamps etc., as necessary, including cutting pipe, making threads etc. complete in all respect with two coats of painting with approved paint any height. 15mm dia & 25 mm dia
39Supplying G.I. Pipe (Tata made) with socket at one end including carriage and all other incidental charges. 15mm dia. Medium (1.57 Kg/m)
40Supplying GI plain elbow of approved brand and make. 15mm dia
41Supplying fitting fixing Plain Tee of approved make with necessary joining materials.A) 15mm dia
42Supplying fitting and fixingwhite Vitreous china best quality approved make wash basin with CIbrackets on 75mmx75mm wooden blocks CP waste fittings of 32mm dia ,one approved qualitybrass P pillar cock of 15 mm dia CP chain with rubber plug with of 30 mm dia , approved qualityPVC waste pipe with CP nut 32 mm dia , 900 mm long approved quality PVC conection pipewithHeavy brass CP nut including mending good damages and painting the brackets with two coats of approvedpaint c)630mmsx450mms size
43Pedestal of wash basin of white Vitreous china ware ( rectangular rounded or triangular) of approved make supplied fitted and fixed in position
44Supplying fitting fixing EWC in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. with p trap
45Closet seat of approved make with lid and CP hinges , rubber buffer and brass screws supplied fitted and fixed complete. a) EPWCiv) Bestolite (solid type ) white
46Supplying fitting and fixing 10 ltrs PVC low down cistern conforming to IS specification with PVC fittings complete,CI brackets including two coats of painting to bracket etc. White
47Chromium plated Bib Cock (angular shape with wall flange) (Equivalent to Code No. 5037 & Model - Florentine of Jaquar or similar brand).
48Chromium plated Concealed Stop Cock (Equivalent to Code No. 514(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand).
49(d) (i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).
50Supplying, fitting fixing approved brand PVC connector white flexible, with both ends coupling with heavy brass CP nut, 15mm dia.
51Supplying fitting and fixing HCL Bend without door confirming toISSincluding jointing and painting two coats to the exposed surface with approved paint complete.
52Supplying, fitting & fixing Cast iron double branch equal with door conforming to I.S. 1729/2002 including jointing and painting two coats to the exposed surface with approved paint complete. (Payment of Painting will however be paid seperately). iii) 100mm dia
53Supplying PVC water storage tank of approved quality with closed top with lid (Black) - Multilayer. (a) 500 litre capacity
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail