}

Tender For Construction Of Community Hall At Charkhol Samalbong Gp, Kalimpong Block I, kalimpong-West Bengal

Gorkhaland Territorial Administration-GTA has published Tender For Construction Of Community Hall At Charkhol Samalbong Gp, Kalimpong Block I. Submission Date for this Tender is 17-03-2023. Building Work Tenders in kalimpong West Bengal. Bidders can get complete Tender details and download the document.




Tender Notice

36591016
Tender For Construction Of Community Hall At Charkhol Samalbong Gp, Kalimpong Block I
Open Tender
Indian
West Bengal
kalimpong
17-03-2023

Tender Details

Construction Of Community Hall At Charkhol Samalbong Gp, Kalimpong Block I

Key Value

Document Fees
INR 3000 /-
EMD
INR 59998.0 /-
Tender Value
INR 29.99 Lakhs /-

BOQ Items

Name of work : Construction of Community Hall at Charkhol Samalbong G.P., Kalimpong Block I
Sl. No. Item Description
1Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1.50 m
2Earth work in filling in foundation trenches or plinth with good earthin layers not exceeding 150 mm. including watering and ramming etc.layerby layer complete .(payment to be made on the basis of measurement of finished quantity of work). (a) With earth obtained from excavationof foundation.
3Laying 150 mm. to 200 mm. boulder soling including rough dressing hand packing and ramming down small pieces in the interstics without rolling but including ramming.
4Cost of stone boulder 150 mm size delivered ans stacked at site.
5(II) Cement concrete with 30 mm. down graded shingles excluding shuttering.N.B. VarietyIn ground floor . 1:3:6 proportion
6Rubble masonry in cement (1:6) with hard dressed stones from approved quarries and clean, coarse and washed sand including carriage of all materials to site. In fine dressed work in building In Ground Floor
7Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor). (a) 25 mm. to 30 mm. thick wooden shuttering as per decision & direction of the Engineer-in-charge
8Ordinary cement concrete(mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes. River bazree
9Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc.initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. (a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel.
10125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.
11Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals). ( c) Sal : Siliguri.
12Panel shutters of door and window, as per design (each panel consisting of single plank with out joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single plank, panel rate of reduction of 20% will be made). (ii) 40 mm.thick shutters with 19 mm. thick panel of size 30 to 45cm. (b) sishu,gamar,Champ,badam,bhola, mogra,Hallak, .
13Supplying, fitting and fixing windows and ventilators with or withoutintegrated grills conforming to IS 1038-1975 and manufactured fromrolled steel sections conforming to IS 7452-1974 with non-frictionprojecting type, box type hinges, glazing clips, lugs locking bracket,handle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete ( 1:2:4) with stone chips 20mm down cutting holes and mending good damages to match withexisting surface complete in all respect excluding glazing.(Add extra @ 1.2 % for each additional floors upto 4th floor and @1.5% for each addl. Floor above 4th floor.)In Ground floorFlash butt welded windows and ventilators(No shop priming will be allowed to facilitate inspection ofworkmanship)Without integrated grill (b) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. [The extra rate admissible for theopenable portion only]
14Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete (In all floors for internal wall & upto 6m height for external wall ). (i) 3 mm. thick (weighing 7.4 kg/sq.m.).
15supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately). (a) 40mm x 6mm, 250mm Length .
16Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. (ii) With 1:4 cement mortar . (a) 20 mm.thick plaster.
17Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. (ii) With 1:4 cement mortar . b)15mm thick plaster
18Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m.
19Artificial stone in floor, dado, staircase etc. with cement conctrete (1:2:4) with stone chips laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners includingraking out joints or roughening of concrete surface and application of cement slurry before flooring works, using cement @ 1.75 kg./sq.m. all complete including all materials and labourIn ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted) with ordinary cement.Using grey cement. (ii) 25 mm. thick.
20M.S. structural works in roof trusses with tubular sections conforming to IS: 806- 1957 & IS: 1161- 1958 connected to one another with bracket,gusset,cleats as per design, direction of Engineer-In-Charge complete including cutting to requisite size. fabrication with necessary metal arc welding conforming to IS: 816- 1956 & IS: 9595 using electrodes of approved make and brand conforming to IS: 814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section. consumables such as electrodes, gas and hire charges of all tools and plants and labour required for the work including all incidental charges such as electricity charges, labour insurance charges etc.(Payment to be made on the basis of calculated weight of structural tubular members as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with the weight of finished structural members. The rates are considered for a height of erection 8m./ 2nd. floor leves fromthe ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initial 8m. or part ther of. (i) For trusses spanning up to 12.00 m.
21Galvanized corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugaion minimum side lap. ( payment to be made on area of finished work). (GCI sheet to be supplied by contractor). In Roof with 0.60mm thick sheet
22Galvanised iron sheet ridging fitted with necessary bolt, screws, washers etc complete. (225 mm end lapping). (A) 300mm laping each way. (b) With 0.63 mm sheet.
23Galvanized iron sheet eaves gutter fittedand fixed with necessary 50 mm X 6 mm.M.S.flat bar clamps bent to design, bolts. Nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping). (a) 225 mm. wide gutter.
24Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. UPVC pipes / 110mm dia
25(A) Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (excluding the cost of bolts,paints but including the cost of nails, screw etc.)(The quantum should be corrected up to three decimals). Sal, Siliguri
26P.V.C- False Ceiling :Providing False Ceiling made with framework of steel tube of 40mm x 20mm ofnot less than 18 gauge,the long and cross section will be welded with each other1000mm to 1200mm apart the entire framework will be fixed in wall usingrawlplug or gutties or screws etc. and suspended from ceiling with M.S flat19mmx3mm as necessary,the entire frame will be painted with red oxide.PRINTED LAMINATED P.V.C Section 150mm x 12mmx 1.00mm (+/- 0.01mm)of approved quality and colour will be fixed on the frame so that the entireframework will not be visible from below P.V.C Section will be fixed with theframe with the help of self tapping steel screws including all materials and labourcharges including fitting,fixing the same and hoisting including mending thedamages in all respect and cost of paint as required as per direction of Engineerin-Charge .In ground floor.
27Wooden eaves board as per design, fitted and fixed complete:In ground floor (i) Plain eaves board (Local Sal) 19mm thick
28Rendering the Surface of walls and ceiling with White Cement baseWATER PROOF wall putty of approved make & brand.(1.5 mm thick)
29(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.
30(b) Priming one coat on timber or plasteredsurface with syntheticenamel oil bound primer of approved quality including smoothening surfaces by sand papering etc.
31(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sandparpering etc. in cluding using of approved putty etc. on the surface , if necessary. (b) On steel or other metal surface: (1) With super gloss (hi-gloss).two coats
32Applying interior grade acrylic primer of approved quality and brand on plasteredor concrete surface old or new surface to received distemper /Acrylic emulsion paint including scraping and preparing the surface thoroughly , complete as per manufactured specification and as per directions of the EIC.In ground floor. (b) two coats. (i) water based interior grade Acrylic primer.
33Applying exteriorgrade Acrylic primer of approved quality and brand on plaster or concrete surface old or new surface to receive decorative textured (mat finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly complete as per manufacturer"s specification and as per direction of the EIC. In Ground Floor:.
34Acrylic Distemper to interior wall, ceiling with a coat of solvent basedinterior grade acrylic primer (as per manufacturer"s specification)including cleaning and smoothning of surface.Two Coats
35Applying decorative cement based paint of approved quality after preparing the surface including scraping the same throughly (plastered or concrete surface) as per manufacturer"s specification. In ground floor. Two coats
36Iron butt hinges of approved qualityfitted and fixed with steel screws, with ISI mark. (v) 75 mm x 60 mm x 3.15 mm.
37Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:. (v) 75 mm x 60 mm x 3.15 mm.
38Anodise aluminium Aldrop/Slidingbolts of approvedquality manufactured form extruded section conforming to I.S. specifictation (I.S.2681/66) fitted and fixed complete. (iii) 300 mm x 16 mm dia. Bol
39Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. (a) With continuousplate base (hexagonal/round rod). (ii) 100 mm grip x 10 mm dia rod .
40(b) Supplying "Godrej"mortice lock chromium plated with keys 6 levers, including fitting and fixing complete.
41SANITARY AND PLUMBING WORKS :- Construction of Septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (4:1) including two 560 mm dia. R.C.C. manhloe cover of approved make supplied, fitted and fixied in the top slab with necessary fittings, 19 mm thick cement plaster(4:1) with neat cement finish to the internal surfaces and 12 mm thick plaster(4:1) to outside wall upto 200 mm below G.L. floor finished with 25 mm thick grey artificial stone including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, fliing up the chamber with clear water, removing foreign materialsfrom the chamber and including constructing attached inspection pit as per approved dawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 5% by weight of cement, complete in all respect as per directon of Engineer-in-Charge. For 20 users. With Bazree
42Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc.complete in all respect including cost of necessary fitting as required, jointing materials and two coats of painting with approved paint in any position above ground.( Payment will be made on the center line measurements of total pipe line including all specials. No seperate payment will be made for accesorie, specials.). For exposed works 125mm dia medium quality
43Supplying, fitting and fixing CPVC (Chlorinated PolyvinylChloride) pipes of approved make conforming to IS-15778:2007 . with all necessary accessories, specials viz. socket,bend, tee, union, cross, elbo, nipple, longscrew, reducingsocket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, fitting, fixing etc. completein all respect including cost of all necessary fittings asrequired,jointing materials in any position above ground.(Payment will be made on the centre line measurements oftotal pipe line including all specials. No separate paymentwill be made for accesories, specials.(a) For Exposed Work For exposed works 15mm dia (i) CPVC Pipes Class-I,SDR-11
44Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved makecomplete in position with necessary bolts, nuts etc. With "P" trap (with vent).
45Supplying, fitting and fixing 10 litre porcelian low-down cistern of approved make without fitting and brackets.White.
46Wash basin white vitreous china of approved make(without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mmwood blocks and C.I. Brackets including two coats of painting of C.I. Brackets. 550 mm x 400 mm size.
47Supplying, fitting and fixing bib cock or stop cock. Chromium plated Bib Cock short body (Equivelent to Code No.511 & Model- Tropical /sumthing special of ESSCO or Similar brand).
48CP Pillar Cock Super Deluxe with Aerator-15 mm. (Equivalent to Code No. 508 & Model No. Tropical/Sumthing Special of ESSCO or similar brand).
49Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer. 500 litres capacity
50Supplying, fitting and fixing PVC pipes of approved make ofof Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI Pi;es as per IS:1239 (Part-I) with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting piles, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made seperately). For Exposed Work PVC Pipes. 15mm dia
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail