|
| 1 | Supplying and Fixing of 3 Nos. Open Air Gym at villages Moda Khera, Siswal and Mohabbatpur Block Adampur |
| 2 | Air Swing: Providing, designing and fixing ofairs winging pair of size 1150 x900 x1250 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 50mm dia 3.3mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powdercoated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and Base platecover shall be made up of virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintained free, duly oiled sealed and self lubricated made by reputed company to be approvedbyEngineer-in-Charge.Equipmenttobe fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in- Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 3 | Arm Wheel :- Providing, designing andfixing Arm Wheel in a pair of size 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60 mm dia 3.3 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. Bearingusedshall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in- Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 4 | Double Cross Walker :- Providing, designing and fixing Double Cross Walker of size 1600 X 600 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60 mm dia 3.3 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100- 130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing.Padalsshall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in- Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 5 | Elliptical Exerciser / Sky walker Providing, designing and fixing Elliptical Exerciser of size 1200 X 540 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.3 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100- 130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handlebars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in- Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 6 | Horse Rider Station: Providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.3mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powdercoated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in- Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval ofEngineer-in-Charge regarding material,shape ofequipment,colouron metal seat and base cover plate and fixing of equipment etc |
| 7 | Leg Press: Providing, designing and fixing of stair stepper in a combination of pair and a single step of size 2000 X 550 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.3 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufacturedby rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, dulyoiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in- Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 8 | Pull Chair: Providing, designing and fixing of Pull pair of size 2500 X 800 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.3mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coatedusingAkzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in- Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 9 | Rowing Machine :- Providing, designing and fixing Rowing Machine of size 1280 X 800 X 1500 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.3 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100- 130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handlebars are to be provided with high quality grip rubber. Foothold shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shallbe maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in- Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment. |
| 10 | Seated Chest Press :- Providing, designing and fixing Seated Chest Press of Pullpair ofsize 1800 X 700 X2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.3 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic weldedwithjoints scallopedas necessary anddressedoffremovingsharpedgesandburrs.Zinc Primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylonalloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, dulyoiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in- Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 11 | Sit Up Station: Providing, designing and fixing of double sit-up station of size 1500 x 1150 x 650 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.2mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and Base plate cover shall be made up of virgin LLDPE plastic by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. The equipment should be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and when concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in- Charge regarding material, shape of equipment, colour |
| 12 | Stair Stepper: Providing, designing and fixing of stair stepper in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 50mm dia 3.3mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat tobe made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in- Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
| 13 | Twister :- Providing, designing and fixing Twister of size 1700 X 1300 X 1300 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 60mm dia 3.3 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 100-130 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in- Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc |
