Construction Of Skac Office Building (1St Floor Remaining Parts) At Officers Colony, By Lane - 3, Dibrugarh, dibrugarh-Assam

Construction of SKAC Office Building (1st Floor Remaining Parts) at Officers Colony, By Lane - 3, Dibrugarh Const. Of Skac Office Building (1St Floor Remaining Parts), Officers Colony By Lane - 3, Dibrugarh , Civil Works , Demolishing Cement Concrete Manually/ By Mechanical Means Including Disposal Of Material Within 50 Metres Lead As Per Direction Of Engineer - In - Charge. 15.2.1 Nominal Concrete 1:3:6 Or Richer Mix (I/C Equivalent Design Mix) , Steel Reinforcement Steel Reinforcement For R.C.C. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Up To Plinth Level. , Form Work Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For 5.9.5 Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers , Reinforced Cement Concrete Work In Walls (Any Thickness), Including Attached Pilasters, Buttresses, Plinth And String Courses, Fillets, Columns, Pillars, Piers, Butments, Posts And Struts Etc. Above Plinth Level Up To Floor Five Level, Excluding Cost Of Centering, Shuttering, Finishing And Reinforcement :1:1.5:3 (1 Cement : 1.5 Coarse Sand(Zone-Iii) Derived From Natural Sources : 3 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources) , Half Brick Masonry With Common Burnt Clay F.P.S. (Non Modular) Bricks Of Class Designation 7.5 In Superstructure Above Plinth Level Up To Floor V Level. 6.13.1 Cement Mortar 1:3 (1 Cement :3 Coarse Sand) , Plastering Works 12 Mm Cement Plaster Of Mix : 13.4.1 1:4 (1 Cement: 4 Coarse Sand) , 15 Mm Cement Plaster On The Rough Side Of Single Or Half Brick Wall Of Mix : 13.2.1 1:4 (1 Cement: 4 Fine Sand) , Providing Wood Work In Frames Of Doors, Windows, Clerestory Windows And Other Frames, Wrought Framed And Fixed In Position With Hold Fast Lugs Or With Dash Fasteners Of Required Dia & Length (Hold Fast Lugs Or Ash Astener Shall Be Paid For Eparately). 9.1.3 Kiln Seasoned And Chemically Treated Hollock Wood , Providing And Fixing Isi Marked Flush Door Shutters Conforming To Is : 2202 (Part I) Non-Decorative Type, Core Of Block Board Construction Withframe Of 1St Class Hard Wood And Well Matched Commercial 3 Ply Veneering With Vertical Grains Or Cross Bands And Face Veneers On Both Faces Of Shutters:9.21.1 35 Mm Thick Including Isi Marked Stainless Steel Butt Hinges With Necessary Screws , Providing And Fixing Panelled Or Panelled And Glazed Shutters For Doors, Windows And Clerestory Windows, Fixing With Butt Hinges Of Required Size With Necessary Screws, Excluding Panelling Which Will Be Paid For Separately, All Complete As Per Direction Of Engineer-In-Charge. (Note:- Butt Hinges And Necessary Screws Shall Be Paid Separately) 9.5.3.1 35 Mm Thick Shutters , Providing And Fixing Glazing In Aluminium Door, Window, Ventilator Shutters And Partitions Etc. With Epdm Rubber / Neoprene Gasket Etc. Complete As Per The Architectural Drawings And The Directions Of Engineer-In-Charge . (Cost Of Aluminium Snap Beading Shall Be Paid In Basic Item): 21.3.2 With Float Glass Panes Of 5 Mm Thickness (Weight Not Less Than 12.50 Kg/Sqm) , Providing And Fixing Isi Marked Aluminium Butt Hinges Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is: 1868) Transparent Or Dyed To Required Colour Or Shade With Necessary Screws Etc. Complete: 9.95.1 125X75x4 Mm , Providing And Fixing Aluminium Sliding Door Bolts, Isi Marked Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868), Transparent Or Dyed To Required Colour Or Shade, With Nuts And Screws Etc. Complete : 9.96.1 300X16 Mm , Providing And Fixing Aluminium Tower Bolts, Isi Marked, Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete : 9.97.1 300X10 Mm Each 117.65 , Providing And Fixing Aluminium Handles, Isi Marked, Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete : 9.100.1 125 Mm Each 60.05 , Providing And Fixing Factory Made P.V.C. Door Frame Of Size 50X47 Mm With Awall Thickness Of 5 Mm, Made Out Of Extruded 5Mm Rigid Pvc Foam Sheet, Mitred At Corners And Joined With 2 Nos Of 150 Mm Long Brackets Of 15X15 Mm M.S. Square Tube, The Vertical Door Frame Profiles To Be Reinforced With 19X19 Mm M.S. Square Tube Of 19 Gauge, Epdm Rubber Gasket Weather Seal To Be Provided Through Out The Frame. The Door Frame To Be Fixed To The Wall Using M.S. Screws Of 65/100 Mm Size, Complete As Per Manufacturer’S Specification And Direction Of Engineerin- Charge. , Providing And Fixing Factory Made Panel Pvc Door Shutter Consisting Of Frame Made Out Of M.S. Tubes Of 19 Gauge Thickness And Size Of 19 Mm X 19 Mm For Styles And 15X15 Mm For Top & Bottom Rails. M.S. Frame Shall Have A Coat Of Steel Primers Of Approved Make And Manufacture.M.S. Frame Covered With 5 Mm Thick Heat Moulded Pvc C Channel Of Size 30 Mm Thickness, 70 Mm Width Out Of Which 50 Mm Shall Be Flat And 20 Mm Shall Be Tapered In 45 Degree Angle On Both Side Forming Styles And 5 Mm Thick, 95 Mm Wide Pvc Sheet Out Of Which 75Mm Shall Be Flat And 20 Mm Shall Be Tapered In 45 Degree On The Inner Side To Form Top And Bottom Rail And 115 Mm Wide Pvc Sheet Out Of Which 75 Mm Shall Be Flat And 20 Mm Shall Be Tapered On Both Sides To Form Lock Rail. Top, Bottom And Lock Rails Shall Be Provided Both Side Of The Panel. 10 Mm (5 Mm X 2 ) Thick, 20 Mm Wide Cross Pvc Sheet Be Provided As Gap Insert For Top Rail & Bottom Rail, Paneling Of 5 Mm Thick Both Side Pvc Sheet To Be Fitted In The M.S. Frame Welded/ Sealed To The Styles & Rails With 7 Mm (5 Mm+2 Mm) Thick X 15 Mm Wide Pvc Sheet Beading Code Description Unit Rate No. Sub Head : 9.0 Wood And P.V.C. Work 201 On Inner Side, And Joined Together With Solvent Cement Adhesive. An Additional 5 Mm Thick Pvc Strip Of 20 Mm Width Is To Be Stuck On The Interior Side Of The C Channel Using Pvc Solvent Adhesive Etc. Complete As Per Direction Of Engineer-In-Charge, Manufacturers Specification & Drawing. 9.120.1 30 Mm Thick Plain Pvc Door Shutters , Providing And Applying Plaster Of Paris Putty Of 2 Mm Thickness Over Plastered Surface To Prepare The Surface Even And Smooth Complete. , Applying One Coat Of Water Thinnable Cement Primer Of Approved Brand And Manufacture On Wall Surface : 13.43.1 Water Thinnable Cement Primer , Applying One Coat Of Water Thinnable Cement Primer Of Approved Brand And Manufacture On Wall Surface : 13.43.1 Water Thinnable Cement Primer , Providing And Fixing M.S. Grills Of Required Pattern In Frames Of Windows Etc. With M.S. Flats, Square Or Round Bars Etc. Including Priming Coat With Approved Steel Primer All Complete. 9.48.1 Fixed To Steel Windows By Welding Kg 181.00 9.48.2 Fixed To Openings /Wooden Frames With Rawl Plugs Screws Etc. , Providing 10 Mm Thick Plaster Of Paris (Gypsum Anhydrous) Ceiling Up To A Height Of 5 Mabove Floor Level, Over First Class Kail Wood Strips 25X6 Mm With 10 Mm Gap In Between And Reinforced With Rabbit Wire Mesh Fixed To Wooden Frame (Frame Work To Be Paid Separately): 12.31.1 Flat Surfaces , Providing And Fixing 6 Mm Dia. G.I. Level Adjusting Hangers (Upto 1200Mm Length), Fixed To Roof Slabs By Means Of Ceiling Cleats Made Out Of G.I. Flat 40X3mm Size 60 Mm Long And Stainless Steel Expandable Dash Fastener Of 12.5 Mm Dia And 50 Mm Long, Complete As Perdirection Of Engineer-In-Charge. Each 70.95 , Providing And Fixing Machine Moulded Aluminium Covering Of Approved Pattern & Design, Made Out Of Machine Cut Aluminium Sheet And Machine Holed For Receiving Dash Fastener, Over Expansion Joints On Vertical Surfaces/Ceiling Floors, The Fixing On Plate In One Row On One Side Of Joint Only Shall Be Done With Stainless Steel Dash Fasteners Of 8 Mm Dia And 75 Mm Long Bolt Including Providing Luminium Washers 2 Mm Thick & 15 Mm Dia , At A Staggered Pitch Of 200Mm Centre To Centre Including Drilling Holes In The Receiving Surface And Providing Expandable Plastic Sleeves In Holes Etc. Complete As Per Direction Of Engineer-In-Charge.21.7.1 Anodised Aluminium Sheet 2.5Mm Thick (Anodised Transparent Or Dyed To Required Shade According To Is: 1868, Minimum Anodic Coating Of Grade Ac 15) Kg 603.30 , Providing And Laying Vitrified Floor Tiles In Different Sizes (Thickness To Be Specified By The Manufacturer) With Water Absorption Less Than 0.08% And Conforming To Is: 15622, Of Approved Make, In All Colours And Shades, Laid On 20Mm Thick Cement Mortar 1:4 (1 Cement : 4 Coarse Sand), Jointing With Grey Cement Slurry @ 3.3 Kg/ Sqm Including Grouting The Joints With White Cement And Matching Pigments Etc., Complete. 11.41A.2.2 Size Of Tile 600 X 1200 Mm , Providing And Laying Machine Cut, Mirror Polished Marble Stone Flooring, In Required Design (Simple Geometrical, Abstract Etc.) And In Patterns In Combination With Italian Marble Stones Of Different Colours, Shades And Finished Surface Texture Etc., In Linear Portions Of The Building, All Complete As Per The Architectural Drawings, With 18 Mm Thick Stone Slab Laid Over 20 Mm (Average) Thick Base Of Cement Mortar 1:4 (1 Cement : 4 Coarse Sand) Laid And Jointed With White Cement Slurry @ 4.4 Kg/Sqm, Including Pointing With White Cement Slurry Admixed With Pigment To Match The Marble Shade, Including Rubbing, Curing And Polishing Etc. All Complete As Specified And As Directed By The Engineer-In-Charge. 11.52.1 18 Mm Thick Italian Marble Stone Slab, Perlato, Rosso Verona, Fire Red Or Dark Emperadore Etc. , Providing And Laying Polished Granite Stone Flooring In Required Design And Patterns, In Linear As Well As Curvilinear Portions Of The Building Allcomplete As Per The Architectural Drawings With 18 Mm Thick Stone Slab Over 20 Mm (Average) Thick Base Of Cement Mortar 1:4 (1 Cement : 4 Coarse Sand) Laid And Jointed With Cement Slurry And Pointing With White Cement Slurry Admixed With Pigment Of Matching Shade Includingrubbing, Curing And Polishing Etc. All Complete As Specified And Asdirected By The Engineer-In-Charge.11.56.1 Polished Granite Stone Slab Colour Of Black, Cherry/Rubyred Or Equivalent , Providing And Fixing Stainless Steel ( Grade 304) Railing Made Of Hollow Tubes, Channels, Plates Etc., Including Welding, Grinding, Buffing, Polishing And Making Curvature (Wherever Required) And Fitting The Same With Necessary Stainless Steel Nuts And Bolts Complete, I/C Fixing The Railing With Necessary Accessories & Stainless Steel Dash Fasteners , Stainless Steel Bolts Etc., Of Required Size, On The Top Of The Floor Or The Side Of Waist Slab With Suitable Arrangement As Per Approval Of Engineer-Incharge, (For Payment Purpose Only Weight Of Stainless Steel Members Shall Be Considered Excluding Fixing Accessories Such As Nuts, Bolts, Fasteners Etc.). Kg 612.25 , Providing And Fixing Glass Mossaictiles On Finished Plain Wall Surface Of Size 20 Mm X 20 Mm X 4 Mm In All Colour, Design , Fixing In Customize Design As Per Direction Of Engineer-In- Charge. The Glass Mosaic Tiles To Be Fixed On The Wall Surface With The Help Of Approved Adhesive Applied At The Rate Of 2.5 Kg Per Sqm And Grouting Of The Same. The Rate Is Inclusive Of All Operation, Material And Required Pattern Approved By Engineer-In-Charge , Sanitation Installation & Internal Water Supply , Providing And Fixing White Vitreous China Pedestal Type Water Closet (European Type) With Seat And Lid, 10 Litre Low Level White Vitreous China Flushing Cistern & C.P. Flush Bend With Fittings & C.I. Brackets, 40 Mm Flush Bend, Overflow Arrangement With Specials Of Standard Make And Mosquito Proof Coupling Of Approved Municipal Design Complete, Including Painting Of Fittings And Brackets, Cutting And Making Good The Walls And Floors Wherever Required : 17.3.1 W.C. Pan With Isi Marked White Solid Plastic Seat And Lid , Providing And Fixing White Vitreous China Flat Back Or Wall Corner Type Lipped Front Urinal Basin Of 430X260x350 Mm And 340X410x265 Mm Sizes Respectively With Automatic Flushing Cistern With Standard Flush Pipe And C.P. Brass Spreaders With Brass Unions And G.I Clamps Complete, Including Painting Of Fittings And Brackets, Cutting And Making Good The Walls And Floors Wherever Required : 17.4.2 Range Of Two Urinal Basins With 5 Litre White P.V.C. Automatic Flushing Cistern , Providing And Fixing Wash Basin With C.I. Brackets, 15 Mm C.P. Brass Pillar Taps, 32 Mm C.P. Brass Waste Of Standard Pattern, Including Painting Of Fittings And Brackets, Cutting And Making Good The Walls Wherever Require: 17.7.3 White Vitreous China Wash Basin Size 550X400 Mm With A Pair Of 15 Mm C.P. Brass Pillar Taps Each , Providing And Fixing Mirror Of Superior Glass (Of Approved Quality) And Of Required Shape And Size With Plastic Moulded Frame Of Approved Make And Shade With 6 Mm Thick Hard Board Backing : 17.32.4 Rectangular Shape 1500X450 Mm , Providing And Fixing Ptmt Towel Rail Complete With Brackets Fixed To Wooden Cleats With Cp Brass Screws With Concealed Fittings Arrangement Of Approved Quality And Colour. 17.73.2 600 Mm Long Towel Rail With Total Length Of 645 Mm, Width 78 Mm And Effective Height Of 88 Mm, Weighing Not Less Than 190 Gms. , Providing And Fixing 3 Layer Pp-R (Poly Propylene Random Copolymer) Pipes Confirming To Is:15801 Uv Stabilized & Anti - Microbial Fusion Welded, Having Thermal Stability For Hot & Cold Water Supply, Including All Pp - R Plain & Brass Threaded Polypropylene Random Fittings, Including Trenching, Refilling & Testing Of Joints Complete As Per Direction Of Engineer-In-Charge. External Work 18.6.9 Pn - 10 Pipe, 110 Mm Od (Sdr-11), , 18.6.7 Pn - 10 Pipe, 75 Mm Od (Sdr-11) , Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes, Having Thermal Stability For Hot & Cold Water Supply, Including All Cpvc Plain & Brass Threaded Fittings, Including Fixing The Pipe With Clamps At 1.00 M Spacing. This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement And Testing Of Joints Complete As Per Direction Of Engineer In Charge. Internal Work - Exposed On Wall 18.7.5 40 Mm Nominal Dia Pipes , 18.7.3 25 Mm , Providing And Fixing Ball Valve (Brass) Of Approved Quality, High Or Low Pressure, With Plastic Floats Complete : 18.18.3 25 Mm Nominal Bore , Providing And Fixing Gun Metal Non- Return Valve Of Approved Quality (Screwed End) : 18.19.3.2 Vertical , Providing And Placing In Position Hand Pump Of Approved Quality For 40 Mm Diameter G.I. Pipe Complete With All Accessories. , Providing And Placing On Terrace (At All Floor Levels) Polyethylene Water Storage Tank, Is : 12701 Marked, With Cover And Suitable Locking Arrangement And Making Necessary Holes For Inlet, Outlet And Overflow Pipes But Without Fittings And The Base Support For Tank. Per Litre 9.70 , Providing And Fixing C.P. Brass Long Nose Bib Cock Of Approved Quality Conforming To Is Standards And Weighing Not Less Than 810 Gms. 18.50.1 15 Mm Nominal Bore , Providing And Fixing C.P. Brass Stop Cock (Concealed) Of Standard Design And Of Approved Make Conforming To Is:8931. 18.52.1 15 Mm Nominal Bore , Electrification , Supplying And Fixing 12 Module Cover Plate , Supplying And Fixing 12 Module (125Mmx125mm) Box , Supplying And Fixing 6 Module Cover Plate , Supplying And Fixing 6 Module (200Mmx75mm) Box , Supplying And Fixing 4 Module Cover Plate , Supplying And Fixing 4 Module (125Mmx75mm) Box , Supplying And Fixing 3 Module Cover Plate , Supplying And Fixing 3 Module (100Mmx75mm) Box , Supplying And Fixing 2 Module Cover Plate , Supplying And Fixing 2 Module (75Mmx75mm) Box , 32 Mm Dia(19 Mm Thick Insulation) , 6 Pin 15/16 Amps Modular Socket Outlet, Isi Marked , Installation, Testing And Commissioning Of Tube/Lamp Etc , S.P. 5/6 Amps, One Way Modular Switch, Isi Marked , 3 Pin 5/6 Amps Modular Socket Outlet, Isi Marked , Stepped Type Modular Fan Regulator (2 Module) , Ceiling Rose, 3 Pin, 5 Amps Isi Marked , 1.5 Sq. Mm Isi Marked, Frls Pvc Insulated,Single Core Copper Conductor Cable , 2.5 Sq. Mm Isi Marked, Frls Pvc Insulated,Single Core Copper Conductor Cable , 4.0 Sq. Mm Isi Marked, Frls Pvc Insulated,Single Core Copper Conductor Cable , 10 Sq. Mm Isi Marked, Frls Pvc Insulated,Single Core Copper Conductor Cable , 16/0.20 Mm (0.5 Sqmm) Twin Core Frls Pvc Sheathed, Flat Flexible Copper Cable , Laying Of One Number Pvc Insulated And Pvc Sheathed / Xlpe Power Cable Of 1.1 Kv Grade Of Following Size Direct In Ground Including Excavation And Refilling The Trench Etc As Required, But Excluding Sand Cushioning And Protective Covering. , Supplying, Installation, Testing & Commissioning Of Heat Detector Operating At 54ºc/57ºc With Rate Of Rise Cum Fixed Temperature (Dual Thermistor) Type With Mounting Base Complete With All Connection Etc. As Required. , Iron Screws, 35 Mm X 6 Mm , 12 Way, Spn, Double Door, Mcb Db , 6 Amps. To 32 Amps. Ratings , Tpn Mcb, “C” Curve,10 Ka Breaking Capacity , 40 Amps., 2 Pole Isolator , Electrification , Providing And Fixing Plain Lining With Necessary Screws/Nuts & Bolts/Nails, Including A Coat Of Approved Primer On One Face, And Fixed On Wooden /Steel Frame Work, Complete As Per Direction Of Engineer-Incharge (Frame Work Shall Be Paid For Separately).12Mm Thick Commercial Ply Conforming To Is : 1328 Bwr Type , Providing And Fixing Cupboard Shutter With 19Mm Thick One Side Decorative And Other Side Balancing Lamination Factory Pressed Bwp Grade Marine Ply As Per Is 710 Of Approved Brand Including 2Mm Thick Pvc Edge Banding Tape With Hot Glue By Edge Bending Mach , Providing Wood Work In Frames Of False Ceiling, Partitions Etc. Sawn And Fixed In Position With Necessary Stainless Steel Screws Etc.Kiln Seasoned And Chemically Treated Hollock Wood , Providing & Fixing Decorative High Pressure Laminated Sheet Of Plain / Wood Grain In Gloss / Matt/ Suede Finish With High Density Protective Surface Layer And Reverse Side Of Adhesive Bonding Quality Conforming To Is : 2046 Type S, Including Cost Of Adhe1.0 Mm Thick , Stainless Steel Self Tapping Screw Of 6X50mm With Ss Hex Cap And 3Mm Thick Epdm Seal , Glue , M.S. Wire Nails , Tv Units (55) , Readymate Wooden Partition , Ii ) C.P.2-Way Bibcock With Wall Flange

Refer document

Refer document

INR 59.91 Lakhs /-

Name of Work: Construction of SKAC Office Building (1st Floor Remaining Parts) at Officers Colony, By Lane - 3, Dibrugarh

Sl. No.	Item Description
1	CIVIL WORKS
2	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
3	Steel reinforcement Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.
4	FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers
5	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, butments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
6	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand)
7	PLASTERING WORKS 12 mm cement plaster of mix : 13.4.1 1:4 (1 cement: 4 coarse sand)
8	15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.1 1:4 (1 cement: 4 fine sand)
9	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or ash astener shall be paid for eparately). 9.1.3 Kiln seasoned and chemically treated hollock wood
10	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction withframe of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
11	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) 9.5.3.1 35 mm thick shutters
12	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
13	Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 9.95.1 125x75x4 mm
14	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 9.96.1 300x16 mm
15	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.97.1 300x10 mm each 117.65
16	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.100.1 125 mm each 60.05
17	Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.
18	Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture.M.S. frame covered with 5 mm thick heat moulded PVC "C" channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading Code Description Unit Rate No. SUB HEAD : 9.0 WOOD AND P.V.C. WORK 201 on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the "C" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer"s specification & drawing. 9.120.1 30 mm thick plain PVC door shutters
19	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
20	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 13.43.1 Water thinnable cement primer
21	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 13.43.1 Water thinnable cement primer
22	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1 Fixed to steel windows by welding kg 181.00 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc.
23	Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 mabove floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): 12.31.1 Flat surfaces
24	Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as perdirection of Engineer-in-charge. each 70.95
25	Providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing luminium washers 2 mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge.21.7.1 Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) kg 603.30
26	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41A.2.2 Size of Tile 600 x 1200 mm
27	Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 11.52.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.
28	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade includingrubbing, curing and polishing etc. all complete as specified and asdirected by the Engineer-in-Charge.11.56.1 Polished Granite stone slab colour of Black, Cherry/RubyRed or equivalent
29	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). kg 612.25
30	Providing and fixing Glass mossaictiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge
31	SANITATION INSTALLATION & INTERNAL WATER SUPPLY
32	Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid
33	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.4.2 Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern
34	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.3 White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps each
35	Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.4 Rectangular shape 1500x450 mm
36	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.2 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.
37	Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. External work 18.6.9 PN - 10 Pipe, 110 mm OD (SDR-11),
38	18.6.7 PN - 10 Pipe, 75 mm OD (SDR-11)
39	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 18.7.5 40 mm nominal dia Pipes
40	18.7.3 25 mm
41	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 18.18.3 25 mm nominal bore
42	Providing and fixing gun metal non- return valve of approved quality (screwed end) : 18.19.3.2 Vertical
43	Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories.
44	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. per litre 9.70
45	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1 15 mm nominal bore
46	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 18.52.1 15 mm nominal bore
47	ELECTRIFICATION
48	Supplying and fixing 12 module cover plate
49	Supplying and fixing 12 Module (125mmX125mm) box
50	Supplying and fixing 6 module cover plate
51	Supplying and fixing 6 Module (200mmX75mm) box
52	Supplying and fixing 4 module cover plate
53	Supplying and fixing 4 Module (125mmX75mm) box
54	Supplying and fixing 3 module cover plate
55	Supplying and fixing 3 Module (100mmX75mm) box
56	Supplying and fixing 2 module cover plate
57	Supplying and fixing 2 Module (75mmX75mm) box
58	32 mm dia(19 mm thick insulation)
59	6 pin 15/16 amps modular socket outlet, ISI marked
60	Installation, testing and commissioning of tube/lamp etc
61	S.P. 5/6 amps, one way modular switch, ISI marked
62	3 pin 5/6 amps modular socket outlet, ISI marked
63	Stepped type Modular Fan regulator (2 module)
64	Ceiling rose, 3 pin, 5 amps ISI marked
65	1.5 sq. mm ISI marked, FRLS PVC insulated,single core copper conductor cable
66	2.5 sq. mm ISI marked, FRLS PVC insulated,single core copper conductor cable
67	4.0 sq. mm ISI marked, FRLS PVC insulated,single core copper conductor cable
68	10 sq. mm ISI marked, FRLS PVC insulated,single core copper conductor cable
69	16/0.20 mm (0.5 sqmm) twin core FRLS PVC sheathed, flat flexible copper cable
70	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.
71	Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.
72	Iron screws, 35 mm X 6 mm
73	12 way, SPN, double door, MCB DB
74	6 amps. to 32 amps. ratings , TPN MCB, “C” curve,10 KA breaking capacity
75	40 amps., 2 pole isolator
76	ELECTRIFICATION
77	Providing and fixing plain lining with necessary screws/nuts & bolts/nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).12mm thick commercial ply conforming to IS : 1328 BWR type
78	Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending mach
79	Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc.Kiln seasoned and chemically treated hollock wood
80	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhe1.0 mm thick
81	Stainless steel self tapping screw of 6x50mm with SS hex cap and 3mm thick EPDM seal
82	Glue
83	M.S. Wire nails
84	TV Units (55")
85	Readymate Wooden Partition
86	Ii ) C.P.2-way bibcock with wall flange