|
| 1 | EARTH WORK : |
| 2 | Surface dressing of the ground, including removing vegetation and inequalities not exceeding 15 cm depth and disposal of rubbish, lead up to 50 m and lift up to 1.50 m.a) Hard Soil |
| 3 | Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders up to 30 cm size, saturated soil and rock), lift up to 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 4 | Extra for every additional lift of 1.50 m or part thereof for earth work in all soils including shingles, small size boulders up to 30 cm size but excluding saturated soil and rock. |
| 5 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 6 | ANTI-TERMITE TREATMENT: |
| 7 | Pre constructional Anti-termite treatment by applying in the entire leveled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) ltrs. Per square meter of the surface to be spread with light Roding so as to ensure proper |
| 8 | a) with aqueous emulsion having concretion 1:19 with chloropirophose solution (tricel or equivalent) and water, i.e 1% solution. |
| 9 | Diluting and injecting aqueous emulsion for POST-CONSTRUCTIONAL anti-termite treatment necessary tools and accessories to be supplied by the contractors) Along external wall( where apron is not provided) in the vertical surface of the sub structure to a depth of 300mm including excavation channel along the wall and Roding etc. by applying the emulsion at 2.5 ltrs per sqm complete as directed by the department. |
| 10 | a) with aqueous emulsion having concretion 1:19 with chloropirophose solution (tricel or equivalent) and water, i.e 1% solution. |
| 11 | P.C.C WORK : |
| 12 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centering and shuttering in :a) Foundations and plinth |
| 13 | Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering in :a) Foundations and plinth |
| 14 | D.P.C. WORK : |
| 15 | Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone shingle 20 mm nominal size). |
| 16 | R.C.C. WORK : |
| 17 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centering, shuttering and reinforcement in :a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 18 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 19 | Reinforcement cement concrete work in columns, pillars, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 20 | Reinforced cement concrete in suspended floors, roofs, landings and balconies up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering and shuttering and reinforcement with M-20 (1 cement : 1.5coarse sand : 3 stone aggregate 20 mm nominal size). |
| 21 | FORM WORK : |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 23 | a) Foundation, footings, bases of columns etc. for mass concrete. |
| 24 | c) Suspended floors, roofs, landings, shelves and their supports, balconies and chajjas (3.5m height) |
| 25 | d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 26 | e) Columns, Pillars, Posts and Struts etc. |
| 27 | BRICK WORK : |
| 28 | Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand). |
| 29 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 30 | Extra for half brick masonry in superstructure above plinth level and up to floor two level. |
| 31 | Providing brick soling in foundation & under floor with stone/best quality picked jhama bricks, sand packed and laid to panel after preparing the sub grade as directed including all labour and materials and with necessary dewatering complete. |
| 32 | (a) Brick on flat soling. |
| 33 | STEEL WORK : |
| 34 | Reinforcement of RCC work including bending, binding and placing in position complete.a) Mild steel. |
| 35 | b) Tar/ TMT steel |
| 36 | Supplying, fitting and fixing door frame made of M S equal angle of size 40 x 40 x 5 fabricated, welded, mitered and joint as per relevant IS code including fitting 8 Nos of MS hold fast, providing closing/ holding device for two Nos tower bolt of door for each side and 1 no of fitting and fixing of Aldrop ( for single leaf ) to the frame for fixing the door to the frame, applying primer to all steel surfaces fixing the frame to the wall/ RCC members by embedding the hole fast securely in CC block of M-15 Grade complete at all levels as specified and directed ( door hinges to be paid as per relevant item of the schedule of rate). |
| 37 | Providing, fitting and fixing anodized aluminium sliding windows and ventilators of standard section of approved brand (HINDALCO/NALCO/BALCO/JINDAL/ other equivalent primary producer) without horizontal glazing bars, joints, mitered and welded ( manufactured to relevant IS specification) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangement, screws etc as required complete as specified and directed for all levels.(a) 2 Track sliding windows(iv) 5mm clear glass. |
| 38 | Providing, fitting and fixing anodized aluminium framed glazed doors with anodized aluminium frame made of 100mm x 45mm x 2.5mm section of approved brand (HINDALCO/NALCO/BALCO/JINDAL/ other equivalent primary producer) with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm, lock rails 10mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasdket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat, etc. complete as specified and directed by the Department at all levels.(v) 5mm clear glass. |
| 39 | Providing, fitting and fixing MS grills of required pattern forwindows / clerestory windows/ openingwith M. S. flats at required spacing in frame all round , square or round M. S. barswith round headed bolts and nuts or screws.I.) Plain grill. (b) Fixed to steel frames |
| 40 | DOOR : |
| 41 | Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.a) 40 mm thick including anodized aluminum butt hinges with necessary screws. |
| 42 | Supplying fitting and fixing 20mm dia aluminium rod with aluminium bracket at both ends of the pelmet over door and windows as directed and specified at all levels: |
| 43 | FLOORING |
| 44 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., completeb) Size of Tile 600x600 mm |
| 45 | Marble stone flooring with 18mm thick marble stone, as per sample of marble approved by Engineer In-Charge, over 20mm (average) thivk base of cement mortar 1:4 (1 cement : 4 coarse sannd) laid and jointed with grey cement slurry, including rubbing and polishing complete with :(c) Agaria White. |
| 46 | Providing anti-skidtiles of approved quality size, shape and thickness not less than 8mm on floors, skirtings over a cement mortar bed 15mm thick in prop 1:3 ( 1 cement : 3 coarse sand) approved make fixed with Fix-A- Tile ( Choksey/ Sika / Pedelite / Fouf) white cement complete at all levels as specified and directed. |
| 47 | A) CERAMIC(i) Normal range (sizes 300mm x 300mm and above) . |
| 48 | (a) Orient made: Galaxy brown, Galaxy creama, Galaxy pink, Galaxy green, Pulsar beige, Pulsar blue, Pulsar dove, Pulsar pink, Burj brown, Burj green, Burj slate. |
| 49 | White glazed tiles 5mm thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry. |
| 50 | PLASTERING |
| 51 | 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 52 | 15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. |
| 53 | PAINTING : |
| 54 | Providing two coats ofBirla white wall care putty (Water Resistant white cement base putty for concrete/ mortar walls and ceiling both internal and external ) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the Department. ( Total thickness of two coats is maximum 1.5mm ). (i) Thickness 1.5mm |
| 55 | (c) Applying one coat of distemper primer of approved brand and manufacture on wall surface after brushing the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth. |
| 56 | Applying priming coat with ready mixed primer of approved brand and manufacture on steel work. |
| 57 | Painting two or more coats with synthetic enamel paint of approved brand and manufacture in black or chocolate shade on new work over and including an under coat of suitable shade with ordinary paint of approved quality to give an even shade. |
| 58 | Wall painting (Two coats) with plastic emulsion paint of approved brand and manufacture (Asian paints/Berger paint/ ICI paint/ J & n paint/ Nerolac) on new surface to give an even shape after thoroughly brushing the surfaces free from mortar droppings and other foreign matter and sand papers smooth .(a) plastic emulsion paint of approved brand and manufacture (Asian paints/Berger paint/ ICI paint/ J & N paint/ Nerolac) |
| 59 | Finishing wall two coats acrylic emulsion exterior paint of approved brand and required shade, thinning by adding water as per the specification of manufacture after thoroughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the Department(c ) Asian paints/Berger paint/ ICI paint/ J & N paint/ Nerolac |
| 60 | DRAIN : |
| 61 | Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete. |
| 62 | PLINTH PROTECTION : |
| 63 | Making plinth protection with 2nd class bricks on edge in cement mortar 1 : 6 (1 cement : 6 fine sand) over 7.50 cm bed of dry bricks aggregate 40 mm nominal size rammed consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1 : 2 (1 cement : 2 fine sand). |
| 64 | Neat cement punning. |
| 65 | GYPBOARD CEILING : |
| 66 | Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) suspended Ceilingwhich includes G.I perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screws fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mm x 10mm x 0.55mm thick fixed to soffit with GI Cleat and Steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each which lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 298mm c/c, then 12.5mm thick square edge Fulltone/ Sundance/ Cratone/ Louvertone/ textured. Gypboard panels of size 595mm x 595mm (coforming to IS: 2095-1982) is then screw fixed to ceiling section with 25mm long dry |
| 67 | wall screws at 290mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the board are to be jointed and finished so as to have flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall top coat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, grill diffusers, etc. cut out to be made with frame of perimeter channel supported suitably and measured and paid separately as and where necessary). (Glass wool to be measured and paid seperately.)(A) M/F Feame Work with Design type Textured Gypboard Tiles 9.5mm thick. |
| 68 | FAN CLAMP : |
| 69 | Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete. |
| 70 | ROOF TREATMENT : |
| 71 | Preparing the surface in roofslab, chajja, terrace, sunken slab, septic tank, OH tank, raft slab, walls etc by thoroughly cleaning with wire brush etc followed by power washing for making the surface absolutely free from any foreign particles like dust, oil, grease etc and allowing surface to dry complete as directed at all levels. |
| 72 | Providing and applying over roof/raft slab two coats of water proofing slurryprepared with cement, fine sand in prop 1:1 admixed with modified acrylic polymer like cemflex of sika India Ltd / Dr. seal kit seal create (Asian chemical) / RHEOMIX 131 OF BASF by brush @ 0.25% of cement sand mixer (by weight) after proper surface preparation ( surface preparation including through cleaning of surface to be measured and paid separately) as specified and directed by the Department complete. |
| 73 | Supplying, providing, mixing and laying of concrete screed of average 20mm thick or as per drawing/ requirement in proportion 1:2:4 (1- Cement :2-fine sand:4-coarse aggregates) ( by volume) with 10mmand down well graded aggregates and admix with a waterproofing plasticizer like Plastocrete plus of sika India Ltd @ 0.2% by weight of cement and thereafter; scoring the top surface of the concrete screed @ 200mm c/c as specified and directed by the Department. |
| 74 | Structural Glazing works for front Façade. |
| 75 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per Grade 6063 T5 or T6 as per BS:1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-In-Charge. (The item includes cost of material such as Cleats, Sleeves, Screws, etc. necessary for fabrication of extruded aluminium framework. Nothing extra shall be paid on this account.) |
| 76 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including. |
| 77 | Stainless Steel Railing. |
| 78 | Providing and fixing Stainless Steel (Grade 304) Railing made of Hollow Tubes, Channels, Plates and 6mm thick Glass of customized design, etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary Stainless Steel Nuts & Bolts complete i/c fixing the railing with necessary accessories & Stainless Steel Dash Fasteners, Stainless Steel Bolts, etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-In-Charge. (For payment purpose only weight of Stainless Steel members shall be considered excluding fixing accessories such as Nuts, Bolts, Fasteners, etc.) |
| 79 | HARDWARE FITTINGS : |
| 80 | Providing and fixing aluminum sliding door bolts anodized transparent or dyed to required color or shade with nuts and screws etc complete.b) 250 x 16 mm |
| 81 | Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.b) 250 x 10 mm |
| 82 | Providing and fixing aluminum Handles anodized transparent or dyed to required color or shade with necessary screws etc complete.a) 125 mm |
| 83 | Supplying, fitting, fixinganodized aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with countersunk holes for screws including necessary aluminium screws etc complete.(anodized to bright natural matt and satin finished) (t) Door stopper with rubber stopper |
| 84 | Supplying, fitting, brass fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with countersunk holes for screws including necessary C.P.brass screws etc complete.( bright natural matt and satin finished)(j) Door latches(i) 300mmx16mmx5mm |
| 85 | SANITARY WORKS : |
| 86 | Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Liters high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required.a) WC pan with white plastic seat and lid. |
| 87 | Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Liter high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.b) Orissa Pattern WC Pan |
| 88 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or CI brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required. (a) One urinal basin with 5 Litres CI automatic flushing cistern |
| 89 | Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality. |
| 90 | Providing and fixing CP brass waste for wash basins and sinks.a) 32 mm dia |
| 91 | Providing and fixing 600x450 mm beveled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleat with CP brass screws and washers. |
| 92 | Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleats with CP brass screws. |
| 93 | Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleat with CP brass screws (heavy quality).a) 750 x 20 mm size |
| 94 | Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. (a) Jaquar make |
| 95 | Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified.(b) Sona make (i) Towel ring roond |
| 96 | Providing and fixing PVC Cowel of ISI make complete as directed and specified.(iv) 75 mm dia. PVC cowl of ISI make |
| 97 | Providing, fitting and fixing recessed soap tray/ soap dish complete as directed and specified.(a) Parrryware make |
| 98 | Providing and fixing 100mm sand cast Iron grating for gully, floor or Nahani trap. |
| 99 | WATER SUPPLY : |
| 100 | Supplying, fitting and fixing PVC pipes of 6Kg/Cm2 (Supreme/ Prince) or other ISI approvedincluding joining, fitting and fixing with clamps etc as necessary complete at all levels including below GL as directed and specified. (a) In exposed surfaces or trenches. |
| 101 | (ii)110 mm Dia (3.00m long each) |
| 102 | (iv) 75 mm Dia(3.00m long each) |
| 103 | Supplying, fitting and fixing PVC plain single Tee( Supreme/Prince) or other ISI approvedincluding joining, fitting and fixing with clamps etc as necessary complete at all levels including below GL as directed and specified. (a) In exposed surfaces or trenches. |
| 104 | (ii) 110mm Dia |
| 105 | CPVC PIPES |
| 106 | Providing and fixing Chlorinated Olyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fitting with one step CPVC solvent cemrnt and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. (a) Concealed work including cutting chases and making good the wall etc. |
| 107 | (i) 15 mm nominal outer dia Pipes |
| 108 | (ii) 20 mm nominal outer dia Pipes |
| 109 | (iii) 25 mm nominal outer dia Pipes |
| 110 | (iv) 32 mm nominal outer dia Pipes |
| 111 | Providing and fixing Chlorinated Olyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes joining of pipes & fitting with one step CPVC solvent cemrnt and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. (a) External Work. |
| 112 | (i) 15 mm nominal outer dia Pipes |
| 113 | (ii) 20 mm nominal outer dia Pipes |
| 114 | (iii) 25 mm nominal outer dia Pipes |
| 115 | (iv) 32 mm nominal outer dia Pipes |
| 116 | Supplying, fitting and fixing C.P bibcock 15mm dia of approved brandas directed and specified . (G.I & C,P pipes will be measured separately) |
| 117 | Jaquar make |
| 118 | a) Continental/Clarion(i) Standard |
| 119 | Supplying, fitting and fixing Chrome plated (C.P.) stop cock of approved brand and size as mentioned belowas directed and specified . (G.I & C,P pipes will be measured separately) |
| 120 | Jaquar make |
| 121 | a) Continental/Clarion(i) 15mm dia Male/ Female (long thread) |
| 122 | Supplying, fitting and fixing overhead adjustable Chrome plated (C.P.) spray shower 15 mm diaof Sona make with wall flange as directed and specified . ( pipes will be measured separately) |
| 123 | (a) Supreme shower with arm |
| 124 | Providing, fitting & fixing (300x230)mm C.I. yard gully hinges Grating complete as directed and specified ii) 110mm dia |
| 125 | SEPTIC TANK |
| 126 | EARTH WORK : |
| 127 | Earth work in excavation in all kinds of soil (excluding soil containing 50% or more of single or small size boulders up to 30cm size, saturated soil and rock ) including banking in 20cm layers and breaking clods, ramming anddressing up for the purpose of making embankments or filling up ground depressions, lead up to 50m and lift up to 1.50m. |
| 128 | P.C.C. WORK : |
| 129 | Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) excluding the cost of centering and shuttering in :a) Foundations and plinth |
| 130 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centering and shuttering in :a) Foundations and plinth |
| 131 | R.C.C. WORK : |
| 132 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 133 | BRICK WORK : |
| 134 | Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand). |
| 135 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 136 | Providing brick soling in foundation & under floor with stone/best quality picked jhama bricks, sand packed and laid to panel after preparing the sub grade as directed including all labour and materials and with necessary dewatering complete. |
| 137 | (a) Brick on flat soling. |
| 138 | SHUTTERING AND FORM WORK : |
| 139 | Centering and shuttering including strutting, propping etc and removal of form work for :d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 140 | PLASTERING : |
| 141 | 15mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. |
| 142 | Neat cement punning |
| 143 | REINFORCEMENT: |
| 144 | Reinforcement of RCC work including bending, binding and placing in position complete.b) Tar/ TMT steel |
| 145 | C.I. MANHOLE COVER : |
| 146 | Providing, fitting and fixing 450mm dia 90mm thick C.I. Manhole cover & frame of 38Kg weight complete as directed and specified. |
| 147 | MANHOLE : |
| 148 | Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement:5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. |
| 149 | a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg ) |
| 150 | SOAK PIT : |
| 151 | Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mm dia 1.80 m long complete as per standard design. |
| 152 | S.W. PIPE : |
| 153 | Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design.b) 150 mm dia SW pipes |
