|
| 1 | Rewinding of AC motor monoblock pump set of the required capacity with superior copper wire of appropriate sizes including testing etc. complete as required with following specification, 3 phase 2800 to 2900 RPM 400/440 volts. All copper wire will not returned to the Department (a) 7.5HP (Stand by pump shall be provided by the agency for unintrupted supply of water) |
| 2 | (b) 3 HP to 5 HP pump set (Stand by pump shall be provided by the agency for unintrupted supply of water) |
| 3 | Rewinding of AC motor mono submersible pump set of the required capacity with superior copper wire of appropriate sizes including testing etc. complete as required with following specification.(a) Moto bush of (M.S. Crystar, Tiger or equivalent) (4 Nos.), 2. Disc palte (1 No.), 3. Thurst Plate (1 No.), 4. SS Sleeves (2 Nos.), 5. Lath, maintenance work etc. complete in all respect. (a)7.5 HP three phase Mono submersible pump set (Stand by pump shall be provided by the agency for unintrupted supply of water) |
| 4 | (b) upto 3 HP single/three phase mono submersible pump set. (Stand by pump shall be provided by the agency for unintrupted supply of water) |
| 5 | Providing and fixing ampere metre 96X96 square mm (0.30 ampere) of make AE (Automatic Electric) siemen or Havels etc. complete as per the direction of Engineer-in-charge. |
| 6 | Providing and fixing volt meter 96x96 square mm (0 to 500 volts) of make AE (Automatic Electric) Siemen or Havels etc. complete as per the direction of the Engineer-in-charge. Providing and fixing 13-21 range overload relay. |
| 7 | Providing and fixing 32 ampere TPN suitable for motor and other inductive loads ‘C’ series MCB conforming to IS:8826:MCB Amp. Triple pole with nuts of standard and BC 998-1995. 10 KA old and fixing the new MCB as per the direction of Engineer-in-charge. |
| 8 | Providing and fixing cast iron impeller suitable for the mono block pump set(a) 7.5HP |
| 9 | (b) 3.00 HP to 5.00 motor pump set |
| 10 | Providing and fixing ball bearing SKF/NBC in existing motor pump set including greasing, cleaning and setting in position (main and end bearing) for 3.00 HP TO 5.00 HP Motor pump set |
| 11 | Providing and fixing single phasing preventer of approved make L&T Siemen etc. suitable up to 7.5 HP mono block pump set |
| 12 | Providing and fixing spare part for direct on line (SDFA) star delta fully automatic starter L&T and cuttler, hammer, model, make and equivalent make (i) Spare kit without Coil (Silver point) |
| 13 | (ii) Over load relay |
| 14 | (iii) No Volt Coil 380.50 Hz |
| 15 | Dismantling and installation of pump set at site after repairing the same including cartage of motor to the work shop and back at site |
| 16 | Providing and fixing rubber gas kit one set of approved quality in pump set suction and delivery etc. complete |
| 17 | Providing and fixing upto 40 Amp. TPN suitable for motor and other induction load-o-series conforming to IS:8328-1996 EI 898-1995 breaking capacity MC no. 40 TPN/BCB 40 Ampere of havells make including dismantling old and fixing the new wiring and testing etc. Complete as per direction of Engineer-in-charge. |
| 18 | Welding turning and alignment of roller shaft as per direction of Engineer-in-charge. |
| 19 | Providing and fixing PVC insulated water proof 3 phase submersible cable 4 mm copper wire etc complete. |
| 20 | Providing and fixing of starter L & T (MU-G6) or equivalent make to separate the 3-Phase motor upto 5-HP 415 V, Contactor-MK1, Coil Voltage 360V, Orerload relay MK1, Additional protection offered - Single phasing, phase reversal, auto restart supply ON, Indicating lamps - Pump ON, rated insulation voltage - 690V, rated operational voltage - 360 V AC, Comformity to Standand - IS/IEC 60947-4-1 etc. as per direction of Engineer-in-charge. |
| 21 | Providing and fixing of starter L & T or equivalent make to separate the 3-Phase motor upto 7.5-HP 415 V, Contactor-MU, Coil Voltage 360V, Orerload relay MU, Additional protection offered - Single phasing, phase reversal, auto restart supply ON, Indicating lamps - Pump ON, rated insulation voltage - 690V, rated operational voltage - 360 V AC etc. as per direction of Engineer-in-charge. |
| 22 | Providing and fixing of starter L & T (MR-G2) or equivalent make to separate the 1-Phase motor upto 3-HP 230 V, Contactor-MR11W, Coil Voltage 230V, Orerload relay MK1, Additional protection offered - Single phasing, phase reversal, auto restart supply ON, Indicating lamps - Pump ON, rated insulation voltage - 690V, rated operational voltage - 230 V AC, Comformity to Standand - IS/IEC 60947-4-1 etc. as per direction of Engineer-in-charge. |
| 23 | Providing and fixing of starter L & T (MR-G1) or equivalent make to separate the 1-Phase motor upto 2-HP 230 V, Switch-MF1 (two pole), Range- 6.5-11 A, 12-20 A, Indicating lamps - Motor ON, rated insulation voltage - 690V, rated operational voltage - 230 V AC, Comformity to Standand - IS/IEC 60947-4-1 etc. as per direction of Engineer-in-charge. |
| 24 | Providing and fixing C.I. butterfly valve with S.S. spindel complete with all respect i/c removing of existing damaged CI butterfly valve. (a) 100 mm dia |
| 25 | (b)75 mm dia |
| 26 | (c) 65 mm dia |
| 27 | (d) 50 mm dia |
| 28 | Providing and fixing 5HP Three Phase Submersible Monoblock Pump, of make and model Kirloskar KOS-520+ or equivalent make with following specifications:Brand Kirloskar or Equivalent,Motor Winding Copper,Power Rating 3.7 KW,Inlet Size 80 mm,Phase Three Phase,Installation Type VerticalHead Range 8-22 Mtrs,Suction Delivery 80x80 mm,Voltage 200-40 V,Motor Power 5 HP,Discharge Range 1260-90 LPM,Speed 2900,Head 8, 10, 12, 14, 16, 18, 20, 22 m,Outlet Size 80 mm,Warranty 1 Year,Applications Under Ground Water Tanks,Material Impeller: Cast Iron,Delivery Casing: Cast Iron, Motor Body: Cast Iron,Shaft: Stainless Steel,Type Openwell Submersible Pump,Angle Horizontal,Frequency 50 Hz. |
| 29 | Visiting charges of electrician for making required installation of pump or other trouble checking in pump and starter etc. |
