Goa University-GU has published Tender For Construction Of Building For School Of Physical And Applied Sciences. Submission Date for this Tender is 22-12-2022. Building Work Tenders in North Goa Goa. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Clearing grass and removal of rubbish upto a distance of 50 M outside the periphery of the area |
| 2 | Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : |
| 3 | b)All types of Ordinary rock including all types of laterite rock, blasting prohibited |
| 4 | Earthwork in excavation by mechanical means ( hydraulic excavator/manual means in foundationtrenches drain ( not exceeding 1.5 m in width or 10 sq.m on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. |
| 5 | b. All types of ordinary rock including all types of laterite rock, blasting prohibited. |
| 6 | Refilling the foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50M and all lifts and disposal of surplus earth as directed by Engineer in charge |
| 7 | Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete. |
| 8 | b) Moorum |
| 9 | Construction of embankement with approved material obtained from borrowpits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300-2 as per MORTH specification 305 |
| 10 | Dry stone pitching 22.5 cms thick using laterite stone of approved quality including supplying of stone and preparing surface etc. complete. |
| 11 | Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete. |
| 12 | Pre-cast cement concrete solid blocks masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in partitionwalls size of blocks (30 x 20 x 10) |
| 13 | Laterite masonry in neatly dressed stones of size as specified in cement mortar 1:4 ( 1cement : 4 coarse sand ) in foundation and basement |
| 14 | Laterite masonary in neatly dressed stones for 23cm thick masonary walls in c.m 1:4 (1: Cement , 4: coarse sand) in Superstructure from floor I level up to floor V level) |
| 15 | Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in all sizes in superstructure from floor one level upto floor V level ( size of block 30x23x15) |
| 16 | Providing and laying Autoclave Aerated cementblocks masonry (Light Weight Foam ConcreteBlocks) with 100 mm thick AAC blocks in superstructure above plinth level up to floor V level incement mortar 1:4 (1 cement : 4 coarse sand). Therate includes providing and placing in position 2Nos 6 mm dia M.S. bars at every third course ofmasonry work. |
| 17 | Exposed decorative laterite masonry usingPatradevi stone of size as specified and laid asdirected by rchitect in cement mortar 1:4 (1cement : 4 coarse sand) |
| 18 | Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded granitic or basaltic stone aggregate 20mm nominal size ) excluding cost of centering, shuttering and finishing in : |
| 19 | a)all works up to plinth level |
| 20 | Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: |
| 21 | A) all works up to plinth level |
| 22 | Providing and laying cement concrete1:5:10 (1 cement: coarse sand: 10 graded stone aggregate 40 mm nominal size) all round S.W pipes including bed concrete 15 cm thick as per standard design. |
| 23 | b) 150 mm diameter S.W pipe |
| 24 | Providing & laying damp proof course 50 mmthick with cement concrete 1:2:4 (1 cement: 2coarse sand: 4 graded stone agg. 20 mm nominalsize). |
| 25 | Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3graded stone agg 20mm nominal size) a) all works upto plinth level |
| 26 | Providing and laying in position machine batched concrete (BMC), machine mixed anmachine vibrated design mix cement concrete ofspecified grade for reinforced cement concretework including pumping of concrete to the siteof laying but excluding the cost of centering ,shuttering, finishing and reinforcementincluding admixtures in recommendedproportions as per IS 9103 to accelerate, retardsetting of concrete, improve workability withoutimpairing the strength and durability as per thedirection of the Engineer-in-charge. M-30 gradeof reinforced cement conrete by using 420kg ofcement per cu.m. of concrete. All works upto floor V level. |
| 27 | Providing and laying in position ready mixedconcrete (RMC) with usage of OrdinaryPortland Cement manufactured in fully automatic batching plant and transported to siteof work in transit mixer for a lead upto 10kmshaving continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering,shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineerin- charge. All works upto floor V level |
| 28 | v)M-30grade of concrete |
| 29 | Centering and shuttering including strutting , propping & removal of forms for |
| 30 | I) Foundations, Footings, Bases for columns |
| 31 | II)Vertical surfaces such as retaing walls, returnwalls, Partitions, walls (any thickness) includingattached Pilasters, Buttresses, Plinth and stringcourses, Fillets and the like |
| 32 | III) Columns , piers, pillars, abutments, posts and struts ( square, rectangle or polygon in plan ) |
| 33 | iv) sides / soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels plinth beams not exceeding 1M in depth |
| 34 | XIII) Suspended floors , roof landings, shelves & their supports,chajjas |
| 35 | vi) Staircases ( except spiral staircases) excluding landing |
| 36 | xiv) Vertical or horizontal fins individually formingbox louvers or projected bands |
| 37 | Centering & shuttering including Strutting,Propping & removal of forms for sloping orbattering surface (slabs, beams, louvers, etc)including folded plates |
| 38 | (iii) Columns, Pillars, Posts & struts (circular orcurved in plan) |
| 39 | Extra to be added for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and de centering at all levels, over a height of 3.5 m for every additional height of 1m or part thereof ( Plan area to be measured)suspended floors, roofs, landings, beams and balconies( plan area to be measured) |
| 40 | Providing corrosion resistant steel CRS-50 bars of (SAIL, TATA, VIZAG, JSW SteelLtd.)(Confirming to IS 1786 if 1985) for RCCwork including bending, binding & placing inposition in all the floors along with factory made precaste concrete cover blocks of specified s izeswhose compressive strengthis not less than thatof surrounding concrete in the structuralmember . |
| 41 | Providing and laying factory made Shot blastedcement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand,etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Squareshapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. ( Navbharat/ Basant / ACC ) |
| 42 | a) 60 mm thick in all colours except grey (M35 grade) |
| 43 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab. |
| 44 | a) Jet Black |
| 45 | Providing and fixing Granite stone slabs (flamed finish) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete |
| 46 | a) Jet Black |
| 47 | Providing and fixing Granite stone slabs (mirrorpolished) 18mm thick in risers of steps, skirting,dado and pillars laid on cement paste andjointed with grey cement slurry mixed withpigment to match the shade of the slabs,including rubbing and polishing complete |
| 48 | a) Jet black |
| 49 | Providing and fixing Vitrified tiles in different sizes (thickness to be specified bymanufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete |
| 50 | 600 x 600 mm - Light Shades |
| 51 | Providing and and laying vitrified unglazedorcelain tactile floor tiles in different sizes ofJohnson, Somany, Kajaria (thickness to bespecified by the manufacturer) and conformingto IS:15622 of approved make in colours andshades as specified laid on 20 mm thick cementmortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement andmatching pigment etc., complete |
| 52 | a) 300 x 300 mm Design - Liner |
| 53 | b) 300 x 300 mm Design - Buttons |
| 54 | Providing and fixing vitrified matt finished (600 X 600) and 10 mm thick tiles in floor , treads of steps, and landings with cement based high polymer modified quick -set tile adhesive( water based) conformingto IS-15477, using 5kgadhesive per sq.m of tile area, in average 3mm thickness(Johnson, somany ,kajaria). |
| 55 | Providing and fixing vitrified matt finished (600 X 600) and 10 mm thick tiles in floor, treads of steps, and landings on 25 mm thick cement mortar 1:3 and jointed with cement slurry complete(Johnson, somany ,kajaria). |
| 56 | Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. |
| 57 | (C)Wall Ceramic Glazed Tiles : 300 x 600 |
| 58 | Providing and fixing vitrified antiskid tiles (320 x 320) and 10mm thick tiles in floor, treads of steps, landings on 25 mm thick bed of cement mortar 1:3 and jointed with cement slurry complete |
| 59 | Rounding of edges of kotah /granite slab to semi circular slope |
| 60 | Precast plain cement chequered tiles 22 mm thick of required shades laid in floors, treads of steps and landing on 20 mm thick bed of Cement mortar 1:4 (1cement : 4 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete |
| 61 | c.Dark shades using ordinary cement |
| 62 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm |
| 63 | (a)Jet Black |
| 64 | Kotah stone slab flooring over 20 mm (average)thick base laid over & jointed with grey cementslurry mixed with pigment to match the shade ofthe slab including rubbing & complete with baseof cement mortar 1:4 (1 cement : 4 coarse sand) |
| 65 | a) 20 mm thick. |
| 66 | Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in position. |
| 67 | c) first class matti wood |
| 68 | Providing and fixing 38 mm thick panelledglazed or panelled and glazed shutters for doors,windows and clerestory window includinganodized aluminium butt hinges with necessaryscrews: |
| 69 | a) Second class Indian teak wood |
| 70 | Providing & fixing flush door shuttersdecoration type core of block board constructionwith frame of first class hard wood and wellmatched first class Indian teak ply veneeringwith vertical grains and cross bands and faceveneers on both faces of shutters. |
| 71 | b) 35mm thick including anodized aluminium butthinges with necessary screws: |
| 72 | Extra for providing vision panel not exceedin0.1 sq.m. in all types of flush doors (cost of glass excluded) |
| 73 | a Rectangular or square Unit: SQ.M. door area |
| 74 | Providing and fixing one panel WPC doors of make ALSTONE or similar, acid proof with high density, 100% water resistant, termite and borer proof of size as specified by Engineer in charge including cot of material, labour (a) 30mm thick 3 nos. stainless steel hinges with necessary screws . |
| 75 | Providing & fixing anodised aluminium sliding door bolt anodised transparent or dyed required colour and shade with bolts, nuts and screws etc. complete ( ISI mark, Heavy ) |
| 76 | b) 250 x 16 mm |
| 77 | Providing and fixing anodized aluminium flat latch |
| 78 | b) 200mm |
| 79 | Providing and fixing aluminium tower bolt (barrel type) anodised or dyed to required colour or shade with screws etc complete. |
| 80 | ( ISI mark, Heavy ) |
| 81 | a) 300x10 mm |
| 82 | c) 200 x 10 mm |
| 83 | Providing and fixing aluminium handleanodized or dyed to required colour or shade with screws etc. ( ISI mark, Round, Heavy) |
| 84 | a)125mm |
| 85 | b) 100 mm |
| 86 | Providing and fixing 150mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete |
| 87 | Providing and fixing first class Indian teak wood moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surfaces etc. |
| 88 | a) 50 x 12 mm |
| 89 | Providing and fixing brass hydraulic door closer of make Everest/ universal/ Godrejwith necessary screws and fittings complete. |
| 90 | Providing flat iron hold fast 40 cm including fixing to frame with 10mm dia bolts , nuts and wooden plugs and embedded in cement concrete blocks 30 x 10 x 15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 stone aggregate 20 mm nominal size |
| 91 | b) 40 x3 mm flat iron hold fast, 15 cm long |
| 92 | Providing and fixing stainless steel (Grade 304)railing made of Hollow tubes, channels, platesetc.with hairline finish, including welding,grinding, buffing, polishing and makingcurvature (wherever required) and fitting thesame with necessary stainless steel nuts andbolts complete, i/c fixing the railing withnecessary accessories & stainless steel dashfasteners, stainless steel bolts etc., of requiredsize, on the top of the floor or the side of waistslab with suitable arrangement as per approvalof Engineer, ( for payment purpose only weightof stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts,fasteners etc.). |
| 93 | Providing and fixing M.S grill of required pattern in wooden frames of windows etc with M.S flats square or round bars with round headed bolts and nuts or by screws. |
| 94 | a) Plain grill |
| 95 | Providing & fixing aluminium shutters( Jindal Make) as per design including transportation, scaffolding and handling etc, complete. , Adjustable louvered windows using 25 mm x 50 mm tube with exhaust provision with 3.5 mm pin headed glass complete. |
| 96 | Supply and fixing of Aluminium Window (Jindal make) as per design, including transportation, and handling, fixed window with outer frame 38mm x 63mm tube with 75mm oval louver section fixing screw HILTI make and GP silicon etc. Complete |
| 97 | Providing and fixing Aluminium shutters (Jindal make), 27mm-Domal series windows aluminium cleating system as per design including transportation, scaffolding and handling etc, complete. Windows with three track ,three sliding shutters with outer frame 100.6mm x 45mm and shutters 65mm x 27mm kinlong touch lock, epdm gasket, all screws of S.S 304 grade fixing screws of HILTI make complete with G.P Silicon ( excluding GST) |
| 98 | (i) 5mm clear annealed glass of St. Gobain/AIS. |
| 99 | Providing and fixing Aluminium shutters( Jindal Make), 40 mm series windows as per design including transportation , scaffolding and handling etc complete, fixed windows with outer frame 40mm x 42 mm with aluminium cleating system. EPDM gasket , all screws of S.S 304 grade, fixing screws of HILTI make with G.P Silicon |
| 100 | (i) 5mm clear annealed glass of St. Gobain/AIS. |
| 101 | Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section |
| 102 | 12mm cement plaster 1:4( 1 cement : 4 coarse sand ) |
| 103 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1;5 ( 1cement : 5 coarse sand ) and top layer 6 mm thick with cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with sponge |
| 104 | 6mm cement plaster to ceiling 1:3 ( 1cement : 3 fine sand) |
| 105 | Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete. |
| 106 | Extra for plastering done on mouldings, cornices, or arches including neat finish to line and level |
| 107 | a) In one coat |
| 108 | Extra for providing and mixing water proofing material proportion recommended by the manufacturers |
| 109 | a) 12mm cement plaster 1:3 ( 1cement: 3 sand) |
| 110 | Applying priming coat with ready mixed primer of approved brand and manufacture on WOOD WORK complete |
| 111 | Painting two or more coats (excluding priming coat ) with superior quality ready mixed paint(satin finish) for WOOD WORK of approved brand & manufacture in all shades on NEW WORK to give an even shade |
| 112 | Painting three or more coats with acrylic exterior paint of approved brand and manufacture ( such as weather shield, Apex) including applying one coat of cement primer and one coat of surface treatment etc. complete |
| 113 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 114 | Wall painting ( two or more coats) with plastic emulsion paint of approved brand and manufacture including a priming coat on NEW WORK to give an even shade |
| 115 | Applying one or more coat of corroseal ZR epoxy zinc rich primer( mixed corroseal ZR based and curing agent in prescribed proportion ( 1:1) by volume and allow it to remain for 10 minutes |
| 116 | Painting two or more coats of Anti-corrosive Epoxy Paint on Steel Work of approved brand on New work to give an even shade.( Asian Paints / Surfa Coat) |
| 117 | Providing waterproofing treatment over the RCC roof terraces by speading cement slurry over the RCC slab and laying of 10 cms, average laterite stoneballast coba with the necessary gradient for easy flow of rain water and the coba in covered terraces and balconies with damp proof of jointless water proofing plaster of mix 1:3 (1 cement :3 fine sand), finished smooth with wooden trowel with false markings of 30cm square.The vertical surface of the adjoining walls are to be treated up to a height of 30 cms includingrounding of junction(the rate includes for complete itemsincluding labour and materials and including bcost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when necessary for filling honey combs ,cracks etc in the RCC slabs)NOTE:cement consumption 25 Kg/ sq.m |
| 118 | Providing and filling in the sunken slabs with C.M 1:4 . Broken laterite soling stones to be laid in layerswith mortar and top layer of I.P.S finish (1:2:3) over brickbat cobafilling etc complete in all floors. |
| 119 | Neat cement punning |
| 120 | Providing anti – termite treatment to buildingsconforming to I.S.S. 6113 part II 1971 (revised)including adopting precautions for healthhazards and safety measures as required therein with the cost of all materials, chemicals, plants,equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (Thepayment will be made on plinth of the building. |
| 121 | a)Pre-construction |
| 122 | Providing & Fixing of Aluminium Lay-in Perforated Tile Ceiling on 24 /14 mm ‘T’ Framework of module 600mm x 600mm. Tiles of size 575mm X 575mm / 584mm x584mm made out of 0.6mm thick Aluminium. Perforation of the tiles shall be 2.5mm dia 5.5mm c/c. The Tile shall be manufactured on advanced equipment, which includes several levelling. The tile end shall be raised upward by 38mm and bend outward to lay the tile in framework. The Tile shall be Polyester based, powder coated in white colour. Grid system for fixing ceiling tiles shall comprise of Tees. The 24 /14 mm main tee runners shall be suspended at an interval of 1200mm centre to centre. The 24 /14 mm cross tee runner shall be suspended at 600mm centre to centre and further supported with 24 /14 mm cross tee at 600mm centre to centre with interlocking arrangements to form grid of 600mm x 600mm. The main tee shall be supported by means of 4mm G.I. rod fromslab/roof. The suspension shall be provided at 1200 to 1500mm centre to centre. Tee framework would be made of GI and Powder coated. Acoustic Felt: Non-woven felt made of glass-reinforced fibre glued over the perforation for sound absorption. |
| 123 | Gypliner or equivalent ceiling which includesproviding & fixing G.I. HG angle of sie 0.55 mm thick having two equal flanges of 25 mm each screw fixed to brick wall / partition with the help of nylon sleeves & screws at 610 mm c/c. Then suspending chan 12.5 mm tapered edge Gypboard (confirming to IS:2095-1982) is thenfixed to channel section with 25 mm drywall screws at 230 mm centre. Screw fixing is done mechanically with drill machine and suitable attachment. Finally square and tapered edges joints of the boards are jointed and finished so asto have flush look which includes filling finishingwith jointing compound, joint paper tape and two coats of Drywall top coat suitable for Gypboard (as per recomended practices of India Gypsum Limited). |
| 124 | Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing.This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. of make ASTRAL/ASHIRWAD |
| 125 | a)15 mm dia nominal outer dia pipes. |
| 126 | b)20 mm dia nominal outer dia pipes. |
| 127 | c)25 mm dia nominal outer dia pipes. |
| 128 | d)32 mm dia nominal outer dia pipes. |
| 129 | Providing and fixing ASTM UPVC pipe,conforming to ASTM 2467 with ISO 14001,including all UPVC plain & brass threadedfittings, including fixing the pipe with clamps at1.00 m spacing. This includes jointing of pipes &fittings with one step UPVC solvent cement andtesting of joints complete as per direction ofEngineer. Internal work - Exposed on wall. |
| 130 | I SCH-80(blue)/(white) |
| 131 | a)20mm outer dia |
| 132 | b) 25mm outer dia. |
| 133 | c) 32mm outer dia. |
| 134 | d) 40mm outer dia. |
| 135 | e) 50mm outer dia. |
| 136 | Providing and fixing ASTM UPVC pipe,conforming to ASTM 2467 with ISO 14001,including all UPVC plain & brass threadedfittings, including jointing of pipes & fittings withone step UPVC solvent cement, trenching ,refilling & testing of joints complete as perdirection of Engineer. External work. |
| 137 | I SCH-80(blue)/(white) |
| 138 | c 32mm outer dia. |
| 139 | d 40mm outer dia. |
| 140 | e 50mm outer dia. |
| 141 | Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes ofapproved including lubricant etc. complete (single/double) socketed: |
| 142 | a) 110 mm dia |
| 143 | b) 75 mm dia |
| 144 | Providing and fixing single Tee of rigid PVC(approved make ) for S.W.R. pipes includinglubricating etc complete, with door : |
| 145 | a) 110 mm dia |
| 146 | b) 75mm dia |
| 147 | Providing and fixing single “Y”of rigid PVC S.W.R pipes (soil, waste & rain water drainage pipes ofapproved make including lubricant etc. complete,with door |
| 148 | a) 110 mm dia |
| 149 | b) 75 mm dia |
| 150 | Providing and fixing rigid PVC bend ( approved make) for SWR pipes including lubricatingetc complete, with door |
| 151 | a)110 mm dia |
| 152 | b) 75mm dia |
| 153 | Providing and fixing double “Y”of rigid PVC S.W.R pipes (soil, waste & rain water drainage pipes ofapproved make including lubricant etc. complete,with door |
| 154 | a) 110 mm dia |
| 155 | b) 75 mm dia |
| 156 | Providing and fixing R.P.V.C vent cowl |
| 157 | a) 110 mm dia |
| 158 | Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design : |
| 159 | b) 150 x 100 mm size –P or S type |
| 160 | Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand)RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 40mm nominal size )inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) neatly finished complete as per standard design. |
| 161 | d) Inside size 60 x 60 cm and 60cm deep including C.I cover with frame (light duty ) 455 x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 Kg) |
| 162 | b) Inside size 90 x 80 cm and 60 cm deep including C.I cover with frame ( light duty ) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg) |
| 163 | Extra for depth for manholes : a) size 90 x 80 cm |
| 164 | Providing and fixing NICKEL chrome platedcopper alloy Fancy BIB Cock Short Body Jaquarmake or equivalent. Confirming to IS 8931;1993 |
| 165 | a)15mm nominal bore |
| 166 | Providing and fixing Nickel chrome plated copper alloy BIB cock (long body) JAQUAR make with wall flange or ARK SUPREME confirming to IS 8931; 1993 |
| 167 | a) 15 mm nominal bore |
| 168 | Providing and fixing NICKEL chrome platedcopper alloy Fancy two way long body bib cockwith wall flance Jaquar make or ARK supremeConfirming to IS 8931;1993 |
| 169 | a) 15 mm nominal bore |
| 170 | Providing and fixing C.P concealed angle stop cock (heavy) with wall flange of (ARK SUPREME/JAQUAR) make 15 mm nominal bore |
| 171 | Providing and fixing NICKEL chrome platedcopper alloy Fancy concealed stop cock withsheet flance 20mm(ARK SUPREME/JAQUAR) makeConfirming to IS 8931;1993 |
| 172 | a) 20 mm nominal bore |
| 173 | Proving and fixing white vitreous china watercloset squatting pan (Indian type w.c. pan) size580 mm with 100 mm sand cast iron P. or S trap10 litres high level P.V.C. flushing cister (ofapproved make) with fittings, rack bolts 32 mmdiameter P.V.C telescopic flush pipe with fittings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling ofapproved municipal design and nylon pullcomplete cutting and making good the walls andfloors where required(HINDUSTAN/CERA) |
| 174 | b) Orissa pattern W.C. pan |
| 175 | Providing and fixing vitreous China water closet squatting (European type W.C pan) with seat and lid C.P brass hinges and rubber buffers 10 lts high level PVC flushing cistern ( of cera conventional “s” /p trap) with fittings rack bolts, 32 mm, dia PVC telescopic flush pipe with fittings and clamps 25 mm PVC over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon chain and pull complete, cutting & making good the walls & floors where required. ( HINDUSTAN/CERA) |
| 176 | a) WC pan – Hindustan /Cera conventional EWC of white colour with white plastic lid & seat. |
| 177 | b) PVC FLUSHING CISTERN ( HINDUSTAN/CERA) |
| 178 | White colour Hindustan sleek with all fittings. |
| 179 | Providing and fixing vitreous China table top wash basin inclusive ofJacquar make fittings etc complete. |
| 180 | ALD–CHR- 709L130 – CP coupling. |
| 181 | ALD–CHR- 769– CP bottle trap |
| 182 | CON-CHR-127BKN- CP sink cock with swan neck tap with RH operating knob. |
| 183 | -18”connection pipe of ARK make |
| 184 | a) White colour table top wash basin of size 500 x 420 x 190 mm cat no. FNS-WHT-4093 of Jaquar make |
| 185 | Hindustan(constellation )/equivalent Cera make |
| 186 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 including cutting of stone and making good the walls wherever required :Kitchen sink with drain board with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete |
| 187 | (a)Overall size 1040mmx510mm (41"x20") bowl size 460mmx410mmx200mm (18"x 16"x 8") depth 200 mm. Glossy. 1.0mm thk, |
| 188 | Providing & fixing bevelled edge mirror ofsuperior glass (5mm thk) of approved Quality,shape & size complete with CP brass screws andwashers, Cleats, CP studs etc Complete. |
| 189 | Providing and fixing C.P jali (Round) |
| 190 | Making connection of G.I distribution branch with main 50mm to 80mm nominal bore by providing and fixing tee including treading the pipe etc complete. |
| 191 | Providing and fixingP.V.C. connection pipe with brass unions 15 mm nominal bore: |
| 192 | c) 18” (45 cm) length (ARK make) |
| 193 | Providing and fixing brass full way valve (heavy) duty with wheel of approved quality. ZOLOTO make |
| 194 | b) 20 mm nominal bore |
| 195 | c) 25 mm nominal bore |
| 196 | d) 32 mm nominal bore |
| 197 | e) 40 mm nominal bore |
| 198 | f) 50 mm nominal bore |
| 199 | g) 65 mm nominal bore |
| 200 | Providing and fixing nahani trap ofrigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door : |
| 201 | a) 110 mm dia |
| 202 | Providing and fixing 40mm dia GI pipes outlet in cement mortar 1:3 ( 1cement : 3 fine sand) including cutting and making good the wall |
| 203 | Providing & fixing CP brass towel rail fixed in wooden cleats with CP brass screws |
| 204 | a) 24” sizeCAN- CHR- 1111SM, Jaquar make |
| 205 | Providing & fixing soap dish chromium plated fixed to wooden cleats with CP brass screws. |
| 206 | a) Soap dish,JAQUAR make |
| 207 | Providing & fixing Nickel chrome plated copper alloy health faucet with 8 mm dia, 1.20 meter long flexible tube and wall hook. |
| 208 | a) Jacquar make (ALD-CHR-573) |
| 209 | Providing and fixing CP Brass toilet paper holder fixed to wooden cleats with CP brass screws a) JAQUAR make(CHR-1151N) |
| 210 | Providing and fixing urinal valve auto closing system CP with built in control cock with 8 mm dia 300 mm long pipe, wall flange etc. complete. JACQUAR make (PRS-CHR-077) |
| 211 | Providing and fixing WHITE vitreous china flat back lipped front Urinal basin of JAQUAR Make inclusive of C.P waste coupling,dome shaped, Urinal spreader, Urinal bracket( Cat no :URS-WHT-13257) |
| 212 | Providing and placing on terrace roof of floor two (1st floor roof) single piece rotational moulded polythene water storage tank having ISI mark and confirming to IS 12701; 1996 including tank connectors. |
| 213 | b) 500 lit capacity |
| 214 | c) 1000 lit capacity |
| 215 | Jointing of rigid SEL FIT PVC pipes by cleaning the pipes with solvent cement including the cost of solvent cement and hydraulic testing of joints etc. complete as per IS : 7634- 19 75 Part : 3, including hydraulic testing of joints as directed by the Engineer in Charge |
| 216 | Outer dia in mm |
| 217 | a) 63 mm |
| 218 | c) 90 mm |
| 219 | d)110mm |
| 220 | f) 160 mm |
| 221 | h)200 mm |
| 222 | Conveying carefully from stack at site, 250mm from both sides rolling and lowering in trenches, laying true to lineand level and perfect linking for joints for PVC/HDPE complete in all respects as per the direction of the Engineer-in-Charge |
| 223 | a) 63 mm |
| 224 | c) 90 mm |
| 225 | d)110mm |
| 226 | f) 160 mm |
| 227 | h)200 mm |
| 228 | Supplying at store or site of work Rigid PVC (SEL FIT)pipes for public water supply including Railway freight,carting, loading and unloading, stackig, transit insuranceetc. complete, Conforming to IS: 4985-2000, and bearingISI mark, Class 10 kg/cm2. |
| 229 | Outer Dia in mm |
| 230 | a) 63 |
| 231 | c) 90 |
| 232 | d) 110 |
| 233 | f) 160 |
| 234 | Supplying and fixing at the site of work of Steel FibreReinforced Concrete (SFRC) manhole covers withframes made as per IS :12592 (part I and II )- 1991 inconcrete M45grade. The covers and lapped in 2mmthick. steel plate and this plate & lifting hooks are dulypainted in corrosion resistant epoxy paint etc. complete. |
| 235 | I Light Duty ( 2.50 Metric Tonne Capacity) |
| 236 | Size in mm |
| 237 | a 300x300 |
| 238 | c 450x600 |
| 239 | d 450x900 |
| 240 | Providing and fixing Informatory/Direction SignBoards with any shape and size made out of 14gauge (2.0 mm) thick Aluminium sheet 3mm thickAluminium Composite panel bonded withwhite/green/blue (as required) fully covered RetroReflective sheeting of (CRG)/Ultralite Gade(highintensity) Engineering Grade(EG), having pressuresensitive adhesive and aRetro Reflective cut outborder and messages in white pressure sensitiveadhesive,fixed on M.S. ANGLE 65x65x6mm 3.65(ironpost) painted with one coat of primer and two coats offinish paint having black and white bands.Firmlyfixed to ground by means ofproperly designed foundation with M15 grade cement concrete45cmx45cmx60cm,60 cm below ground level as perapproved drawing. |
| 241 | Retro reflective sheeting of crystal grade(CRG) |
| 242 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section(CHS) IS1161 closed Structural Steel of (SAIL, TATA. VIZAG, JSW ,APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 243 | Steel work welded ( SAIL, TATA, VIZAG & using electrodes of AdOr make only) in built up sections trusses and framed work including cutting, hoisting, fixing in position with anchor fasteners ( Hilti HST) and applying zinc chromite primer |
| 244 | b) In tees, angles ,flats and channels as per the design |
| 245 | Skylight - Danpalon Or Equivalent Day light PanelSystem: Supply & fixing of 16mm thick 600 mmwidth MULTIWAL MULTICELL polycarbonatesystem consist of: The panels shall be niform incolor with an integral Microcell core. In a crosssection, the core shall be constructed of tightcells with 6 walls. Panels will be supplied withVertical Standing Seam at both sides of the panelSnap-on connector to interlock the panels shallhave a grip-lock double tooth lockingmechanism to ensure maximum uplift capability& shall be of same color as that of panel foraesthetic appeal.NOTE : Necessary Steel structure to be providedby the Steel fabricator. Skylights framework tobe raised by by 200 mm from Roof Pan level. |
| 246 | Providing and fixing colour coated galvuliumroofing sheets of 0.5mm thickness including allthe accessories (TATA / JSW make) but excluding thecost of purlins, rafters, trusses, flashings etc.complete as per the directions of the Engineer incharge. |
| 247 | Providing and fixingcolour coated Galvulium Flashings of 0.5 mm thickness( TATA / JSW Make) in - corners,ridges,valleys, gable end and trims Girth up to 610 mm including all the accessories complete as per the directions of the Engineer in Charge. |
| 248 | Providing and Fixing in position Double Skin Standing Seam MxSeam or equivalant Standing Seam Roofing Sheet in 0.55 mm thickness Color Coated Galvalume / Zincalume Steel Sheets with Galvanised Clips. The feed material is manufactured out of nominal 0.55 mm total coated thickness (TCT) & 0.50 mm base metal thickness (BMT), Hi-tensile steel having 245~300 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc & 1.5% Silicon) as per AS 1397 – ZincAl AZ 150 (min. 150 grams / sq. m. total on both sides) with Super Durable Polyester (SDP) Paint finish. The SDP paint will have a total coating thickness of 25 ~ 30 micron, comprising of nominal 20 micron exterior coat on top surface and nominal 5 micron reverse coat on back surface over nominal 5 micron primer coat on both surfaces of approved color shade by concern authority. The profile sheet willbe of TATA BlueScope Steel (TBSL) or JSW SDP or Equivalent make, necessary Test Certifcate has to be provided. Top Skin elements to be supplied in single length with no laps with a sheet element cover width of 480 mm and a standing seam height of 45 mm. Sheets are to be laid to meet the requirements of the building geometry. The roof elements will be supported by and joined longitudinally with an electrically operated closure machine over concealed galvanised clips integrated into the longitudinal element flange thereby allowing for the possibility of transmitting reaction forces resulting from positive and/or negative loads and also accommodating unobstructed thermal movements resulting from the specific ambient temperature variation.The secret fixgalvanised clips shall be capable of transmitting all reaction forces to the purlin without the aid of any other material, thus resulting in an overall “Self-supporting standing seam roof system”.Base Coil : TBSL or JSW SDP or Equivalant make. Rockwool Insulation layer of 50 mm thick, 48kg/m3 density to be laid between two sheets. "Z" Type GI Sub-girt of size 40 x 50 x 40 – 1.5 mm thick will be fixed on liner sheets at all along purlin, the height of 50 mm will cater the thickness of 50 mm thick insulation. Liner Sheets shall be of MxLine or equivalant Profile ofhaving nominal 1050 mm effective cover width and 18 mm corrugation depth at 175 mm center to center spacing in Colour Coated Galvalume / Zincalume Steel materials. The feed material is manufactured out of nominal (0.42 mm BMT)0.50 mm total coated thickness (TCT), Hi-tensile steel with minimum 550 MPa yield strength, metallic hot dipped coated with Aluminium Zinc alloy (55% Aluminium, 43.3% Zinc & 1.6% Silicon) as per AS 1397 - Zinc-Alu. AZ 150 (min. 150 grams/ sq. m. total on both sides) with Super Durable Polyester (SDP) Paint. The paint will have a total coating thickness of nominal 25 µm, comprising of nominal 20 µm exterior coat on top surface andnominal 5 µm reverse coat on back surface over nominal 5 µm primer coat on both surfaces of approved colour shade by concern authority. the steel sheet shall be fastened with nominal 40 micron zinc coated or nominal 25 micron zinc-tin allow coated , hex head, self drilling screw as per aAS 3566-2002 Class -3 fastners of approved make with EPDM washers as per the requirement considering the profile shape anddesign load. the fastnes size shall be calculated as per the design or manufacturers recommendations. |
| 249 | Providing and fixing weepholes with rigid PVC make laid in position with a required slope and level while layingpipes of approved the concrete of retaining wall,wing wall and earth retainig structure complete as directed by the Engineer in charge A) 110 mm dia. |
| 250 | Provision of Hump type speed breakers for general traffic at preferred crossing speed of 25 km/h and above as per standard having and specification in IRC 99-1998. The speed breakers shall be formed by placing premixed bituminious macadam and a layer of asphaltic concrete carpet (hot mix) after the surface is indented and tack coat applied to the location where required. For General traffic of 25 Kmph |
| 251 | Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand ) including testing of joints, etc. complete. |
| 252 | B) 250 mm dia RCC pipe |
| 253 | Painting lines, dashes arrows etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter demarcation at site and traffic control as per MORTH Specification 803 |
| 254 | Upto 10 cm in width |
| 255 | Providing and fixing 0.50mm thick colour coated galvulium Rain Water gutter with machine cut and press bend in as per approved design in line level along with gutter strip, silicon sealant, SDS, etc.complete. |
| 256 | Providing and fixing in position 2mm thick one side embossed clear polycarbonate sheet in same profile to match the roofing sheets including self tapping screws. |
| 257 | Fabrication and fixing of Aluminium composite panel cladding with thick 4mm/ 0.25mm ACP sheets, aluminium framework, with 50 X 25 X 1.2 mm thick sections. Silicon sealants etc. including accessories complete. |
| 258 | Providing and fixing Aluminium single leaf door 40mm series with Aluminium cleating system, mortise cylindrical locking of Kinlong make with both sides key and handles with 8mm Aluminium grill in fill including powder coating ,etc.complete. |
| 259 | Supplying & installation of 600mm dia wind operated turbo ventilator fans for normal/smoke exhaust with FRP base plate, etc.complete. |
| 260 | Melamine polishing on wood work (one or more coat) |
| 261 | Matt |
| 262 | Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½ :3 (1 cement: 1:1½ coarse sand: 3 graded stone agg 20mm nominal size) |
| 263 | Supplying of laterite stone soling of size 150-200 mm size and murrum having P.I. Value not more than 6 and laying including packing with smaller stones and consolidation with power road roller including spreading, watering and consolidation of binding material etc.(Measurements shall be considered on finished item) . |
| 264 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3-wheeled steel/vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density.as per MORTH Specification 404 By Manual Means |
| 265 | Grade - III |
| 266 | Providing and laying 50mm(consolidatedthickness)full grout using granitic or basaltic stone ofspecified grading at 6.00 cu.m. per 100 sq.m. groutingwith hot bitumen straight run bitumen(or with such bituminous material of grade and type as specified by the Engineer-in-Charge)at 5.0kg. per sq. m. binding with key aggregate of granitic or basaltic stone ofspecified grading at 1.5 cu.m. per 100 sq.m. including Providing and laying seal coat sealing the voids in abituminious surface laid with F.E loader with 1 Cu.m. bucket capacity to the specified levels, grade andcross fall using Type A seal coat with 0.98 kg/sqm of bitumen of grade as per MoRT&H specifications clause 513. |
| 267 | Providing and laying bituminous macadam with 40- 60 TPH hot mix plant producing an average output of 50 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder to the specified percentage of total mix , transported to site, with all leads laid over a previously prepared surface with sensor paver finisher to the required grade, level and alignment and rolled with smoth wheeled roller and vibratory roller to achieve the desired compaction,using antistripping agent complete as per MoRT&H Specifications Clause 504 |
| 268 | Grade-II (19mm nominal size)@ 4% of Bitumen-mix |
| 269 | (a) Antistripping agent @ 0.5% of bitumen content |
| 270 | Providing and laying 30 mm thick Bituminious/Asphaltic concrete with 40-60 batch type HMP producing an average output of 50 tonnesper hour using crushed aggregates of specified gradings Premixed with bituminious binder at 6.0 % by weight of total mix and filler incl. ProvidingAntistripping agent.@ 0.50% of bitumen content of,transpoting the hotmix to work site with all leads and applying a tack coat @f 2.00 kg/10sq.m. with hotbitumen of 80/100 and laying withhydrostatic/hydraulic power finisher with sensor control to the required grade, level and alignment,rolling with smooth wheeled, vibratory or tandemrollers to achieve the desired compaction as perMORT&H specifications clause 509 and 503 |
| 271 | (a) Antistripping agent @ 0.5% of bitumen content |
| 272 | ELECTRICAL (B) |
| 273 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 274 | (f) Group C-- with Cat B Modular Accessories |
| 275 | Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 276 | Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required. |
| 277 | (b)Cat B |
| 278 | Supplying and fixing suitable size modular GI box with modular plate and coverin front on surface or in recess including providing and fixing 3 pin 15/16 A modular socket outlet and15/16 Amodular switch connection painting etc. as required. (b) Cat B |
| 279 | Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required. |
| 280 | Supplying and fixing following size modular GI box along with modular base and cover plate for modularswitches in recess etc. as required. |
| 281 | (f)1or 2 module (75mmx75mm) Cat B |
| 282 | Supplying and fixing following modularswitch/ socket on the existing modular plate and switchboxincluding connections but excluding modular plate etc. as required "(h) 5/6 A switch Cat B |
| 283 | Supplying and fixing following modularswitch/ socket on the existing modular plate and switchboxincluding connections but excluding modular plate etc. as required "(k) 3 pin 5/6 A socket outlet Cat B |
| 284 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit (heavy)of appropriate size as required. |
| 285 | (b)2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit) |
| 286 | (c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit) |
| 287 | (i) 4 x 4 sq.mm + 2 x 4 sq.mm earthwire (25mm Conduit) |
| 288 | (j) 4 x 6 sq.mm + 2 x 6 sq.mm earthwire (32mm Conduit) |
| 289 | (k) 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit) |
| 290 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor single core cable in theexisting surface/ recessed steel PVC conduit or casing capping, including dismantling, removing old wires as required. |
| 291 | "(12) 3 x 2.5 sq.mm |
| 292 | Supplying & installing HDMI cable low voltage grade as per specification as per specifications having 15 Metre cord length with male/female 19pin HDMI connectors as per requirements complete. |
| 293 | Supplying and drawing of Cat-6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVS sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection,etc. complete as required |
| 294 | Cat 6 Cable |
| 295 | Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. |
| 296 | b)CAT B |
| 297 | Supplying, fixing, and configuring ethernet managed ethernet switch of 24 ports with 2 SFP + 2 combo port and web view/CLI on provided rack or as directed as per specification no. WG-NWC/GBS |
| 298 | Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP |
| 299 | Supplying and fixing 1 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC |
| 300 | Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 450x550x367 mm) as per specification No. WG-NAS/RAK |
| 301 | Supplying, installing & testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC. |
| 302 | Supplying and fixing of following sizes ofrigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) includingcutting the wall and making good the same in case of recessed conduit as required. |
| 303 | (a) 20 mm |
| 304 | (b) 25 mm |
| 305 | (c) 32 mm |
| 306 | Supplying and fixing 30 A 415 V TPN industrial type socket outlet with4 pole and earth metal enclosed plug top along with 20 A, C seriesTP MCB in sheet steel enclosure in surface or in recess with chained metal cover for the socket outlet and complete with connections testing and commissioning etc. as required |
| 307 | (b) Cat B |
| 308 | Supplying and erecting square / rectangular shaped CRCA /die-cast aluminium powder coated housing LED panel (slim edge-lit) light suitable for 25 to 32W with provision for plane front frame with translucent cover fixed to the housing complete. |
| 309 | Supplying & erecting LED 18W tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated HF electronic driver complete. |
| 310 | Supplying LED concealed type foot / step light with aluminium body for indoor/outdoor application suitable for upto 4W-6W LED including driver and erecting by making necessary arrangement/recess in wall to make it flush with surface. |
| 311 | Supplying & erecting LED 40W tube light fitting (4 feet), 5700K, with polycarbonate housing, heat sink, with industrial grade heavy duty driver complete Havels Cat stoutplus 100bs 40W led 840 spcwh OR Wipro cat no LL24-541-XXX-57-CD (including lamp). |
| 312 | Supplying and erecting bulkhead fitting suitable for LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF |
| 313 | Supplyingand erecting of 56 inch ( 1400mm sweep) ceiling fan, double ball bearing type complete with all accessories |
| 314 | b)Cat B |
| 315 | Supplying and fixing stepped type electronic fan regulator on the existing modularplate switch box including connections but excluding modular plate etc. as required |
| 316 | Cat B |
| 317 | Supply and erecting of 9 inch (225 mm sweep) exhaust fan, 1400 rpm, complete with all accessories. |
| 318 | (a) Cat A |
| 319 | Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required |
| 320 | Supplying and fixing following way TPN sheet steel, double door, Vertical type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinbar detachable gland plate interconnections phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCB and busbars of following ways (but without MCBs as required) |
| 321 | (d) 4 way (8+12), double door, Vertical type, Cat B |
| 322 | (e) 8 way (8+24), double door, Vertical type, Cat B |
| 323 | (f) 12 way (8+36), double door, Vertical type, Cat B |
| 324 | Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) |
| 325 | (f) 8 way double door Cat A |
| 326 | Supplying and fixing following way TPN sheet steel, single door, Vertical typeMCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphatized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCCB and busbars of following ways (but without MCBs as required) |
| 327 | (a) 4 way (8+12), single door, Vertical type, Cat A |
| 328 | (b) 8 way (8+24), single door, Vertical type, Cat A |
| 329 | Supplying and fixing B series SP MCB 240V, suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required" |
| 330 | (c )5A TO 32A, Cat B |
| 331 | Supplying and fixing 6 TO 32A C series MCB, suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required" |
| 332 | (f )SP, Cat B |
| 333 | Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required. |
| 334 | (j) TPN Cat B |
| 335 | Providing and fixing following rating and breaking capacity fixed type/adjustable 3 pole MCCB inside the existing cubicle panel board including drilling holes in cubicle panel making connections etc. as required |
| 336 | (b) 100 A 16 KA, CAT B |
| 337 | (h) 160 A fixed 35/40KA, CAT B |
| 338 | (i) 200 A adjustable 35/40 KA, CAT B |
| 339 | (j) 250 A adjustable 35/40 KA, CAT B |
| 340 | Supply and installation testing and commissioning of Legrand or Equivalent MCCB enclosure up to 160A |
| 341 | Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation ofpit of size 1.0x1.0x 3.0 Metres(min) and disposal of excavated soil. c)Watering GI pipe, 20 mm Class B,with funnel as per specs. d)Charcoal/salt as per specs ( paid separately). e) Refilling the pit of size 1.0x1.0x 3.0 Metres(min) with soft blackagriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. g)watering arrangement(plumbing will be paid separately). |
| 342 | (b) In rocky strata |
| 343 | Extra for using salt and charcoal for GI or Copper plate earth electrode as required (96kgs of charcoal and 5kgs of salt) |
| 344 | Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark, of approved brands, including accessories and providing masonry enclosure with CI/RCC coverhaving locking /lifting arrangement and watering pipe etc.withcharcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation ofpit of size 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c)Charcoal/salt as per specs ( paid separately). d) Refilling the pit of size 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe. g)watering arrangement(plumbing will be paid separately). |
| 345 | (b) In rocky strata |
| 346 | Extra for using salt and coke for pipe earth electrode as required( 160 Kgs of Coke and 5 Kgs of Salt). |
| 347 | Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required |
| 348 | Providing and fixing 4 mm copper wire on surface or in recess for loop earthing etc. as required |
| 349 | Supplying and laying 6 SWG GIwire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required |
| 350 | Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I),IS:7098(Part I) with latest amendments of following size. |
| 351 | (7) 3 1/2x 150 Sq. mm. |
| 352 | (8) 3 1/2x 185 Sq. mm. |
| 353 | Supply of4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. |
| 354 | (5) 4 Core 16 sq.mm |
| 355 | Supplying & laying (including excavation) 25 cm dia RCC Hume pipe of standard thickness at required depth up to 90 cms. Below road / ground surface, for covering provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet |
| 356 | Supply of2 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI markconforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. |
| 357 | 2 Core 4 sq.mm |
| 358 | Supply of4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI markconforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. |
| 359 | 4 Core 4 sq.mm |
| 360 | 4 Core 6 sq.mm |
| 361 | 4 Core 10 sq.mm |
| 362 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface,etc.complete as required |
| 363 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. |
| 364 | (b) Rocky strata |
| 365 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of sizeexceeding 120 sq.mm but not exceeding 400 sq.mm on surface,etc.complete as required |
| 366 | Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, completeas required. |
| 367 | (7) 3 1/2x 150 Sq. mm. |
| 368 | (8) 3 1/2x 185 Sq. mm. |
| 369 | Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, completeas required. |
| 370 | (2) 4 Core 4 sq.mm |
| 371 | (3) 4 Core 6 sq.mm |
| 372 | (4) 4 Core 10 sq.mm |
| 373 | "(5) 4 x 16 Sq. mm. |
| 374 | Supply and making cable end terminations with compression gland and copper lugs for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. |
| 375 | (2) 2 Core 4 sq.mm |
| 376 | Supplying and Installing following size welded ladder type , 50mm depth, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc., complete as required. |
| 377 | d)300 mm width X 50 mm depthwith runner size 15x50x15mm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG) |
| 378 | Supplying and Installing following size perforatedtype 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc., complete as required. |
| 379 | a)100mm width x 50mm depth |
| 380 | d)300mm width x 50mm depth |
| 381 | Supplying and Installing following size perforatedtype , M.S.cable traybends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc., complete as required. |
| 382 | a)100mm width x 50mm depth (16 SWG) |
| 383 | d)300mm width x 50mm depth(16 SWG) |
| 384 | Supplying and Installing following size perforatedtype , M.S.cable traytees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc., complete as required. |
| 385 | a)100 mm width X 75 mm depthwith runner size 20x75x20mm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG) |
| 386 | d)300 mm width X 75 mm depthwith runner size 20x75x20mmmm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG) |
| 387 | PANELS |
| 388 | Design , supply ,installation testing and commissioning ofMain AC panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear.The cable terminations shall be suitable for cable sizes as shown on the drawing as required etcsuitable for outgoingcable sizes as shown on the drawing as required with |
| 389 | Incomer 600A TPN 37KA mccb with thermal magnetic releases suitable for 2x31/2cx300sqmm AYFY cable |
| 390 | 1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc with scada connectivity with necessary cts and suitable RS485/232 port |
| 391 | 1200A 4P copper bus bars of 99.9% purity electrolytic copper |
| 392 | Outgoings |
| 393 | 3 set of 200A , 37KA TPN MCCBs |
| 394 | 1 set of 400A , 37KA TPN MCCBs |
| 395 | AC Main panel as above |
| 396 | Design , supply ,installation testing and commissioning ofM1 AC panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear.The cable terminations shall be suitable for cable sizes as shown on the drawing as required etcsuitable for outgoingcable sizes as shown on the drawing as required with |
| 397 | Incomer 200A TPN 37KA mccb with thermal magnetic releases suitable for 31/2cx300sqmm AYFY cable |
| 398 | 1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc with scada connectivity with necessary cts and suitable RS485/232 port |
| 399 | 800A 4P copper bus bars of 99.9% purity electrolytic copper |
| 400 | Outgoings |
| 401 | 16 set of 60A , 37KA TPN MCCBs |
| 402 | M1 AC panel as above |
| 403 | Design , supply ,installation testing and commissioning ofM2 AC panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear.The cable terminations shall be suitable for cable sizes as shown on the drawing as required etcsuitable for outgoingcable sizes as shown on the drawing as required with |
| 404 | Incomer 200A TPN 37KA mccb with thermal magnetic releases suitable for 31/2cx300sqmm AYFY cable |
| 405 | 1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc with scada connectivity with necessary cts and suitable RS485/232 port |
| 406 | 800A 4P copper bus bars of 99.9% purity electrolytic copper |
| 407 | Outgoings |
| 408 | 13 set of 60A , 37KA TPN MCCBs |
| 409 | M2 AC panel as above |
| 410 | Design , supply ,installation testing and commissioning of Lighting main panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear.The cable terminations shall be suitable for cable sizes as shown on the drawing as required etcsuitable for outgoingcable sizes as shown on the drawing as required with |
| 411 | Incomer 600A TPN 37KA mccb with thermal magnetic releases suitable for 2x31/2cx300sqmm AYFY cable |
| 412 | 1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc with scada connectivity with necessary cts and suitable RS485/232 port |
| 413 | 1200A 4P copper bus bars of 99.9% purity electrolytic copper |
| 414 | Outgoings |
| 415 | 5 set of 200A , 37KA TPN MCCBs |
| 416 | Lighting main panel as above |
| 417 | Design , supply ,installation testing and commissioning of M1 & M2 Lighting panel, M1 & M2 UPS panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear.The cable terminations shall be suitable for cable sizes as shown on the drawing as required etcsuitable for outgoingcable sizes as shown on the drawing as required with |
| 418 | Incomer 160A TPN 37KA mccb with thermal magnetic releases suitable for 2x31/2cx150sqmm AYFY cable |
| 419 | 1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc with scada connectivity with necessary cts and suitable RS485/232 port |
| 420 | 800A 4P copper bus bars of 99.9% purity electrolytic copper |
| 421 | Outgoings |
| 422 | 10 set of 60A , 37KA TPN MCCBs |
| 423 | M1 Lightingpanel as above |
| 424 | Supply installation testing and commisioing of 35W LED post top lantern of 5000K, Wipro make LP09s or Havels Spring 6LED POST TOP |
| 425 | Providing & erecting 4 m high galvanised conical pole with foundation bolts having bottom dia. from 115 to 130 mm, top dia. from 65 to 75 mm on provided foundation as per specification no. OH-PL/CPL |
| 426 | Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete |
| 427 | Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design5m octagonal / conical GI pole).complete (for 3 to 5m octagonal / conical GI pole). |
| 428 | FIRE ALARM SYSTEM |
| 429 | Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall. |
| 430 | Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made complete |
| 431 | Supplying, installing, testing and commissioning optical type smoke detector complete on box as per specification no. FFFAS/SD |
| 432 | Supplying, installing, testing and commissioning manual call point (Pill box) with break glass push button in metal enclosure complete as per specification no. FF-FAAS/MCP |
| 433 | Supplying, installing, testing and commissioning hooters with CRCA enclosure complete as per specification no. FFFAAS/HTR |
| 434 | Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU |
| 435 | Supplying, installing, testing and commissioning of 2 Zones Microprocessor based conventional fire alarm control panel (FACP) with standard accessories complete as per specification no. FF-FAAS/FACP |
| 436 | LIGHTNING PROTECTION |
| 437 | Supply of 8 mm Aluminium Round Conductor complete as specified in drawing & Meets the requirements of DIN EN 50164-2 (VDE 0185 part 202) & VDE 0185-305 (IS/IEC 62305)OBO Type No.RD 8/ALU |
| 438 | Supply of Roof conductor holderfor parapet- Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance OBO Type No.177 30 M8(5207460 ) |
| 439 | Supply of Roof conductor holder - Stainless steel Conductor holder: With Bottom section and conductor holder stainless steel (V2A)Bottom section with Ø 8.5 mm slot. Conductor holder @ 1 meter distance. OBO Type No. 159 VA-V (5217 07 5 ) |
| 440 | Polyamide roof cable holder for flat roof:DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black@ 1 meter distance. OBO Type No.165 MBG-8-10 ( 5218700 ) |
| 441 | Vertical air terminal with accessories: Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mmaluminium rod: 2 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load.Tested as per IEC 62561(1-8) and relevant test report should be submitted. OBO Type No. 101 VL2000 ( 5401983) |
| 442 | Vertical air terminal with accessories: Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mmaluminium rod: 4 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load.Tested as per IEC 62561(1-8) and relevant test report should be submitted. OBO Type No. 101 VL4000 ( 5401995) |
| 443 | Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete OBO type No.F-FIX-S16 I (5450080) |
| 444 | Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and tested upto 100KA lightning current. Tested as per IEC 62561(1-8) and relevant test report should be submitted for 100kA lightning current testing. OBO type No.F-FIX-16 (5403200) |
| 445 | Providing of cross universal connector: For T and cross connection,to route vertical down conductor /mesh formation made of hot dipped galvanisediron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts .OBO Type |
| 446 | Providing of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. OBO Type No. 172 AR ( 5218 92 6 ) |
| 447 | Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece ).OBO Type |
| 448 | Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. OBO Type No. 5052 DIN 30X3 ( 5450436 ) |
| 449 | Supply of diagonal clamp ,For reinforced steel of diameter 6-22mm and Flat 30x3 galvanised steel strip. Installed with screws M10x40. Simple installation with open slot. OBO Type no : 250 A-FT(5313015) |
| 450 | Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. OBO Type No. 255 A-FL30 FT (5314534 ) |
| 451 | Providing of earth fixed point: Made of Stainless Steel, grade 316L. Connection to earthing systems, air terminals and reinforcement. Contact plate: 79 mm diameter, made of rustproof stainless steel (V4A). Clamping bolt 10mm diameter, rustproof (V2A). Including plastic cover for simple installation. OBO Type no : 205 DG L180 V4A (5420 02 2) |
| 452 | Providing of cross connector for reinforcement, Flat galvanised steel and earth fixed point. This connects earth fixed point to reinforcement. Installed with 2 hexagonal bolts M8x 20 (F).OBO Type no : 250(5312 90 6) |
| 453 | Supply of Connector, Rd 8-10 mm with pressure trough with 1 fix contact clamping screw, nut and serrated washer Including pre-mounted pressure sump, steel Conforms to the requirements according to DIN VDE 0185-305 (IEC 62305) OBO Type no : 249 8-10 ST-OT (5311 50 3) |
| 454 | Supply of UL Listed & CPRI Tested maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 14 mm with copper coating thickness of 250micron tested as per IEC 62561-2 .OBO Type No. 14 3000 CCER(5450010) |
| 455 | Universal clamp made of SS to connect rod with flat conductor . OBO Type No. 14 25 RTC(5450066) |
| 456 | Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested.OBO Type No. OEC 2 25(5450058) |
| 457 | The above arrangements shall be provided withHeavy duty earth chamfer of 5000kg load bearing capacity to ensure the safety of earthing system .OBO Type No.UFE(5450030). |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
