Tamil Nadu Veterinary And Animal Sciences University-TANUVAS has published Tender For Establishment Of Goat Research Centre At Chinnakovilankulam Village, Sankarankovil Taluk In Tenkasi District (Part- A Civil Works). Submission Date for this Tender is 14-12-2022. Building Work Tenders in tenkasi Tamil Nadu. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 08-Dec-2022 | Bid Submission Date Extension | Date | 14-12-2022 |
| Sl. No. | Item Description |
| 1 | Civil Works |
| 2 | Earth work excavation for foundation in all soils and sub soils and to full depthas may be directed except in hard rock requiring blasting inclusive of shoring strutting and baling out water wherever necessary refilling the sides of foundation with excavated earth in layers of not more than 15cm thick well rammed consolidated and depositing the surplus earth with in the compound in places shown by the departmental officers within an initial lead and lift and clearing, levelling the site etc., complete complying with standard specifications. |
| 3 | Supplying and filling in foundation, basement, etc with filling Stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 4 | Cement Concrete 1:5:10 (One Cement, Five M.sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification |
| 5 | Refilling in foundation, basement, etc with excavated earth in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 6 | Supplying and filling of Well gravel in basement for filling including conveyance, loading and unloading charges and all other incidential charges, filling, laying, watering and consolidation etc., complete as directed by the Dept., Officers with standard specification. |
| 7 | Providing Pre – constructionAnti – termite treatmentand creating a chemical barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam, all round the Pile Caps, Catch basins, trenches, pits, tunnels, wall trenches, back fill, plinth filling, junction of wallandfloor.Externalperimeterof building, surrounding of pipes, expansion joints, below U.G. sump and retaining/side walls etc. as per instructions of chemical manufacturer as directed by the Department officer/ Architect. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification.The chemical to be used as insecticide for the treatment shall be Biflex Tc, TC stands for Termiticide Concentrate for Termite Control (Bifenthrin) and the application shall be diluted 1 part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification.The work should be carried out by an approved and registered specialist pest control agency only.Tenderer to furnish the name of the proposed specialist firm. A 10 years post application guarantee against defects shall be furnished by the main Contractor. Note: Horizontal plan area at ground floor level of the building will be measured and paid. |
| 8 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete |
| 9 | Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For square or rectangular colums, boxing top and bottom slab, sill slabs, sunshade facia, fins and drops etc., |
| 10 | Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For slabs, rectangular Tee or Eill beams, lintels, staircase waist and landing salbs, landing beams, loft slabs, canopy slabs, beams etc., |
| 11 | Reinforced Cement Concrete 1:11/2:3 (One Cement, one and half M.sand and three hard broken stone jelly) using machine broken 20 mm gauge hard broken granite stone jelly for all RCC item of works excluding cost of reinforcementgrill,fabricating charges, centering and shuttering butincludinglaying,vibrating with mechanical vibrator, finishing, curing, etc., complete andproviding fixtures like fan clampsin theRCCfloor/roof slabwherevernecessaryand bearing surfaces of wall, beam etc.shallbefinishedsmooth withcementmortar 1:3 (One CementandThreeP.Sand) 12mm thick and kraft paper laid over it without claimingextra,etc.,complete complying with standard specification as directed by the departmental officers. For foundation and basement |
| 12 | For superstructure in Ground floor |
| 13 | Reinforced Cement Concrete 1:2:4 (One Cement, two M.sand and four hard broken stone jelly) using machine broken 20 mm gauge hard broken granite stone jelly for all RCC item of works excluding cost of reinforcementgrill,fabricating charges, centering and shuttering butincludinglaying,vibrating with mechanical vibrator, finishing, curing, etc., complete andproviding fixtures like fan clampsin theRCCfloor/roof slabwherevernecessaryand bearing surfaces of wall, beam etc.shallbefinishedsmooth withcementmortar 1:3 (One CementandThreeP.Sand) 12mm thick and kraft paper laid over it without claimingextra,etc.,complete complying with standard specification as directed by the departmental officers. For foundation and basement |
| 14 | For superstructure in Ground floor |
| 15 | Supplying, fabricating and placing in position of steel reinforcements using MS / RTS rods for all RCC works as per design given including cost of steel. Binding wire, straightening the rods, welding of rods, dia above 25mm in all floors complying with standard specifications. [The welding should conform to BIS. Wherever required at contractor’s expense.] |
| 16 | Brick work in Cement Mortar 1:5 (One cement and Five M.sand) using second class ground moulded chamber burnt bricks of size9”x 4½”x 3” for the following including curing, etc., complete complying with standard specification For foundation and basement |
| 17 | For superstructure in Ground floor |
| 18 | Brick partition walls of 11.50cm thickness using best quality II class ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three M. Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) For superstructure in Ground floor |
| 19 | For superstructure in First floor |
| 20 | Plastering with Cement Mortar 1:5 (One cement and Five P.sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 21 | Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P.Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers |
| 22 | Manufacturing, Supplying, erection of M.S. Pipe Posts and M.S. tubular section for trusses, rafters and purlins using suitable size and design as may be directed by the Engineer,i/c., including necessary cleats, bolts nuts and applying a coat of primer etc., complete complying with standard specification. |
| 23 | Supplying and fixing of powder coated galvanized aluminium metal roofing sheet 0.47mm thick JSW or equivalent of ISI make of different colour sheet for roofing with necessary adjustable ridges seater by using “U” or “J” bolts and nuts with washers or SDST screws and also the labour charges for fixing in position etc., complete as directed by the Engineer,i/c., |
| 24 | Supplying fabricating, erecting of colour Galvalume 0.47mmridge sheet including cost of self drilling (SDST) screws with washers, fixing charges lead and lift etc., complete. |
| 25 | Paving the floor with Designed Colour double chargedVitrified tiles of size 60 x 60 x 8mm in all floors over a base layer of Cement Mortar 1:3 (One cement and three M.sand) 20mm thick and pointed with white cement mixed with colouring pigments at the rate of 0.3 Kg/sq.m including finishing neatly and curing, etc. complete, complying with standard specification and as directed by the departmental officers. (The basic cost of tiles should not be less than Rs.80/-- Sq.ft) |
| 26 | Flooring with the Eurocon tiles of size 300mm x 300mm laid over cement mortar 1:3 (One cement and three sand) 20mm thick and pointing the joints to full depth of slabs with cement mortar 1:3 (One cement and three sand) mixed with colour oxide including laying, finishing, polishing with machine polish, curing etc., complete complying with standard specification |
| 27 | Supplying and paving the floor with design mat finished ceramic tiles of approved brand and quality of size 305 X 305 X 6mm in all floors over a base mortar using cement mortar 1:3 (One cement and three M.sand) 20mm thick laid in situ true to alignment and pointed with colour cement (White cement mixed with colouring pigment) to suit the colour and shade of the ceramic tiles used neatly and fixed in position without any air gap in between the ceramic tiles etc., complete complying with standard specification and as directed by the departmental officers. (The sample colour and shade of the ceramic tiles should be got approved from the departmental officers before use on works). |
| 28 | Dadooing walls with best approved quality, printed design colour glazed tiles of size 300 mm x 450 mm x 6 mmsizes set in Cement Mortar 1:2 (One Cement and Two M.sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers |
| 29 | Painting two coats of newly plastered wall surface with ready mixed exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 30 | Painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges etc., as per standard specification.(The colour and shade of the distemper shall be got approved by the Executive engineer before use of work). |
| 31 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Engineer,i/c.,before use on works). |
| 32 | Supplying and fixing of Stainles steel (Salem Stainless steel) Door Frame (Box. Section using stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetall splayed end stainless steel hold fast etc., conforming ISI specified ensured of right butt joint riveted hold assembly with Nylon insert not tobe welded with special purpose of hard were ready to assemble condition for easy installtion at site including dismantling RCC columns walls with power drills to the extend required, including providing concrete 1:2:4 inside the box curing etc., complete.THe cost inclusive of cost of hold fasts plastic bush, insesrt receiver, rubber bottom shock absorbser etc., completion all floors and as directed by the departmental officers. |
| 33 | Supply and fixing country wood scantling (first qualitywood) for door frames including labour charges formaking, applying anti corrosive paint on the back sides of frame and fixing the frame in position, etc. complete complying with standard specification.(The wood have to be got approved by departmental Engineers before use on work). |
| 34 | Supplying and fixing in position of solid core, water proof flush door shutter 35mm thick single leaf of approved make and quality.Both side of the door shall be laminated with 1mm thick lamination sheet of approved colour and quality.The door shall be provided with iron oxide MS hinges of 125mm x 30mm size 3 Nos., aluminium aldrop of size 250 x 16mm – 1 No. aluminium tower of size 250 x 12mm – 1 No. Aluminium tower bolt of size 200x12mm – 1 No., D type aluminium handle of size 125mm – 2 Nos. Aluminium door stopper / magnet catch 3” depth – 1 No. respectively, etc. complete complying with standard specification. |
| 35 | Supplying and fixing of country wood (first quality Paddock) paneled door of double leafusing first class Country wood.The vertical styles will be120mm x 38mm and top rail will be 250mm x 38mm bottom rail and middle rails will be 200mm x 38mm including cost of furniture fittings like oxidized iron butt hinges of size 125 x 30mm - 6 Nos.,Aluminium tower bolt of size 250x12mm – 2 Nos., Aluminium tower bolt of size 200 x 12mm - 1 No., Aluminium aldrop of size 250 x 16mm - 1 No. to be fixed with 40mm bolt, etc. D type aluminium handle of size 125mm – 3 Nos. Aluminium door stopper / magnet catch 3” depth – 2 Nos. respectively, etc. complete complying with standard specification.(Wood shall be Paddok or its equivalent) |
| 36 | Supplying of MS hold fasts of size 330x50x6mm MS flats suitably folded to the rejoined ‘Z’ shape to have two end flabs 50mm long and over all length of the horizontal position as 230mm and including making necessary groove in the two end flats to accommodate screws etc complete |
| 37 | Supplying, fabricating and fixing in position standard pristine white U-PVC (Un-Plasticized Polyvinyl Chloride) partly fixed and partly sliding windows as per the design and drawings and making necessary opening for the exhaust fan fixing in all floors with extruded UPVC sections of required sizes as per IS standard with necessary accessories such as rubber beedings with best quality rubber, lock, handle, supplying and fixing 4mm thick plain / frosted glass including the cost of all materials, labour, power consumption required for the fabrication, drilling holes in RCC columns, floor, mansory wall wherever necessary with power drills to the required extent and making good to the original conditionafter fixing etc., and as directed by the Engineer,i/c., |
| 38 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI / 1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm.The EPDM rubber (black colour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers.The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The ventilator should be got approved from the departmental Engineer,i/c.,before use on work. |
| 39 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) doors the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI / 1mm 125 GSM and 100% corrosion free, the profiles are multi-chambered sections with all thick of 2mm.The FPDM rubber covered with over all the edges of frame and shutter the shutter will be provided with ESPAG multi power point locks and also handle to be provided.The corners and joints should be welded and cleaned.Strong locking systems and as per size for arresting noise and energy loss.The door should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The door should be got approved from the Executive Engineers before use on work. |
| 40 | Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification. |
| 41 | Supplying and fixing in position best approved ISI quality PVC Rain water down fall pipes of 110mm dia meter having working pressure of 4Kg/Cm2 including cost of PVC pipe, with necessary shoes, bends, nails, teakwood plugs, screws etc., and fixing of cost iron gratings of required dia meter and special clamps at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of brass screws, teakwood plugs to be used shall be 150mm X 25mm in front and 200mm X 75mm in rear and all other sides to a depth of 100mm.The PVC pipe shall be fixed with teak wood plugs by means of “U” clamps using brass screws.Special types of “U” clamp at the centre of the pipeline shall be fixed in addition to those for more than 3 meter pipe length complying with standard specifications. |
| 42 | Providing plain cement concrete 1:2:4(one cement, two M-sand, four aggregate) using HBG jelly of size 20mm gauge for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification |
| 43 | Providing Granolithic floor finish for 25 mm thickness using plain Cement Concrete 1:2:4 (One cement, two M.sand, and four stone jelly) using 10 to 12mm hard broken stone jelly and the top surface shall berubbed smooth in all floors, finishing, threading and curing etc., complete complying with standard specification. |
| 44 | Manufacturing supplying and fixing of STEEL DOOR with following section. Outer frame 40 X 40 X 6mm Hollow steel special extruded section at 3.28Kg/RM and shutter frame 35 X 35 X 6mm hollow steel special extruded section at 3.28Kg/RM. Stiffeners with 32 X 6mm at 1.5 Kg/m MS flat is provided as the lock rail of the door and welded in fact on both ends to shutter frame. 20 gauge CR sheets of best quality is laid as panel in the shutters frames. 18X5mm at 0.7 Kg/m MS flat is welded over the 32X6mm at 1.50 Kg/m MS that on the rear side of the sand witching the CR sheet for rigidly.Additional stiffness with 18 X 5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter 2 Nos., of hinges in case of single leaf and 4 Nos., of hinges in case of double leaf shutter is provided 6 Nos., of hold fasts 120mm length spliced at the ends are welded to the outer frames of the door. Tower bolt 2 Nos., one at top and the other at bottom are provided. One aldrop is provided in case of double leaf door at lock rail section in the door. For single leaf doors one more aldrop is provided in the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at in appropriate place, in case of a double leaf door, MS flat 32 X 3mm at 1.10 Kg/m is provided on the edge of one shutter, to conceal the gap between the shutters. A tic bat is provided at the bottom of the outer frame to prevent twisting of frame during transportation of fixing. All members are given a shop coat of red oxide primer etc., as directed by the departmental officers. The rate is include cost of all materials,labour charges, transportation, taxes and all other incidental charges etc., complete. |
| 45 | Supplying and fixing in position of weld mesh door of size as may be directed using 25 X 25 X 6mm M.S. angle for outer frame using 25 X 25 X 6 mm M.S angle and 25 X 6 mm M.S. flats for stiffeners horizontally 3" X 1" M.S. weld mesh 10 gauge for panels including cost of mateirlas,andlabours for wrought and put up, applying a coat of primer etc., complete as directed by the Engineer,i/c., |
| 46 | Supplying and fixing in position ofweld mesh grill of size as may be directed using 40X40x6mm M.S. angle for outer frame, 40X6mm M.S. flats for bracings, 1¼”X 1¼”M.S. weld mesh 10 gauge for panels including cost of materials, labour for wrought and put up and applying a coat of primer etc., complete. |
| 47 | Supplying and fixing in position by means of 75 mm long and 65 mm dia counter sunk bolt and nuts embedded in the floor with rubber or fiber washer white glazed European Water Closet white colour with 100 mm "P" trap with double flapped rigid PVC black seat and seat cover with C.P. brass hinges including supply and fixing 10 litres capacity PVC low level flushing tank with a pair of C.I. brackets, etc., complete with all fittings such as 15 mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40 mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15 mm brass connections, 15 mm G.M. wheel valve, 15 mm brass nipple (2 Nos.), 15 mm nylon connection and fixing the low level ISI marked flushing tank with T.W. plugs and screws and giving necessary connection to the CI / PVC pipe includingcost of 600 mm length of 100 mm dia C.I. Pipe and painting the C.I. Brackets with 2 coats of approved paint over one coat of red oxide primer and redoing the dismantled masonry to original condition etc. complete. (The EWC and flushing tank should be got approved by the Executive Engineer before use on works: Make: Parry ware / Hind ware or its equivalent)) |
| 48 | Supplying and fixing in position CP Two way bib cock 15mm diawith Health faucet of best approved quality and approved make etc.,complete complying with standard specification and as directed by the departmental officers. |
| 49 | Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works). |
| 50 | Providing & fixing first quality white vitreous china oval / round / square wash basin (size as per architectural drawing) for under counter mounting, specially fabricated CI / MS brackets, painted with two or three coats of enamel paint of approved shade over a coat of primer, 32 mm CP brass waste and CP brass cast bottle trap and pipe to wall with CP brass flange and rubber adopter for waste connection complete including filling gap between counter and wash basin with approved type poly sulphide sealant, cutting and making good the walls wherever required. Vanity counter top type. (rate including the granite counter, size as per drawing and RCC slab wherever necessary) |
| 51 | Supplying and fixing C.P. wall mixer 15mm dia2 in 1 with over head Shower Rose with arm of approved make and best quality including labour charge for fixing and finishing, etc. complete complying with standard specification. |
| 52 | Supplying and fixing in position best quality brass chromium plated towel rail of 600mm length 20mm dia with CP brackets of same materials including fixing with necessary T.W. plugs, brass C.P. screws and dismantling masonry etc., complete with standard specifications. (The towel rail should be got approved by the Departmental officer before use on works). |
| 53 | Supplying and fixing in position 15 mm dia C.P. long body tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Departmental Officer before use on the works) |
| 54 | Supplying and fixing in position 15 mm dia C.P. Screw down tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Departmental Officer before use on the works) |
| 55 | Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch.Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493.Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chasing in wall and floors for the pipe, making good the same by using 1:1 cement mortar over the wire meshand providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required or (b) Fixing/supporting the pipes (& fittings) at wall/ceiling level supported by galvanized clamps, hangers etc, as per specification. Exposed pipes to be painted of legends with direction arrow. GI pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the fire rated walls / floors slab and sealing the sleeves with glass wool in between and fire sealant compound at either end all as perProject Manager"s / Consultant requirement.All termination points for installation of faucets shall have brass termination fittings.Installation shall be to as per Technical Manual of manufacturer of pipes & fittings. (Higher Pressure rating with higher pipe thickness) standard dimension Ratio - 11.20mm dia CPVC pipe |
| 56 | 25mm dia CPVC pipe |
| 57 | 32mm dia CPVC pipe |
| 58 | Supplying, laying and jointing UPVC pipe (Schedule-40) of the following dia of approved quality and best variety and laid properly to alignment including fixing the required specials lent excluding cost of such specials but including cutting, threading and fixing to the wall with necessary clamps, screws, teak wood plugs making holes in the wall (or) drilling holes in the roof and making good the disturbed portion to the original condition with necessary brick work and plastering etc., complete complying with standard specifications.(The UPVC pipe should got approved by the Engineer,i/c., before use on work).40mm dia UPVC pipe(Schedule - 40) |
| 59 | Supplying, laying and jointing UPVC pipe of the following dia of approved quality and best variety and laid properly to alignment including fixing the required specials lent excluding cost of such specials but including cutting, threading and fixing to the wall with necessary clamps, screws, teak wood plugs making holes in the wall (or) drilling holes in the roof and making good the disturbed portion to the original condition with necessary brick work and plastering etc., complete complying with standard specifications.(The UPVC pipe should got approved by the Engineer,i/c., before use on work). 50mm dia UPVC pipe - (Schedule - 80) -Below Ground Level |
| 60 | Supplying and fixing in position best quality PVC soil waste pipes of various size having ISI mark and pressure of 6 Kg/Sq.cm providing leak proof joints with PVC adhesive etc. including fixing to the walls with necessary T.W. plugs, brass screws mild steel clamps etc. and giving connection to the sanitary fittings including dismantling brick masonry /RCC works / roof slab etc. wherever necessary and making good the dismantled portion to the original condition, complying with standard specifications etc. complete (The PVC pipe should be got approved by the Departmental Officer before use on works).- 75mm dia pipe 6 Kg / Cm2 with ISI mark |
| 61 | 110mm dia pipe 6 Kg / Cm2 with ISI mark |
| 62 | Providing and fixing in position 100mm PVC .Multi inlet Floor traps with CP grating, joining, embedding in concrete etc. complete rate to include making of opening in floor, marble / tiles, for fixing grating. Size 100 mm x 75 mm floor trap |
| 63 | Providing inspection chambers of various sizes using 9” thick brickwalls using second sort tablemoulded chamber burnt bricks of sizes 9”x 4½”x3” in Cement Mortar 1:3 (One cement and three sand) 12mm thick and outside surfaces in C.M. 1:5 (One cement and five sand) 12mm thick.A precast cover slab of 75mm thick shall be provided for the chamber.The rate includes necessary earth work excavation to the required depth, Plain Cement Concrete 1:5:10 (One cement five sand and ten aggregate) 75mm thicketc., complete.-0.60x0.60x0.60 Mtr |
| 64 | Supplying and fixing in position the following UPVC specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and pipes jointing the special complete complying with standard specifications.(The PVC specials used on the work shall be got approved by the departmental officer before use on work).50mm dia UPVC ElbowWith ISI Mark |
| 65 | 50mm Dia UPVC TEE with ISI mark |
| 66 | 50mm dia UPVC Coupler with ISI mark |
| 67 | Supplying and fixing in position CPVC specials such as plain bend, door bend, plain tee, door tee, off sets of various sizes of best approved quality conforming to ISI and providing leak proof joint including fixing to wall etc., complete complying with standard specification.(The specials should be got approved by the Engineer,i/c., before use on work).32mm dia CPVC ElbowWith ISI Mark |
| 68 | 25mm dia CPVC Elbow with ISI mark |
| 69 | 20mm dia CPVC Elbow with ISI mark |
| 70 | 32mm dia CPVC TEE with IISI mark |
| 71 | 25mm dia CPVC TEE with ISI mark |
| 72 | 20mm dia CPVC TEE with ISI mark |
| 73 | 32mm dia CPVC coupling with ISI mark |
| 74 | 25mm dia CPVC coupling with ISI mark |
| 75 | 20mm dia CPVC coupling with ISI mark |
| 76 | 32mm dia CPVC union with ISI mark |
| 77 | 25mm dia CPVC union with ISI mark |
| 78 | 20mm dia CPVC union with ISI mark |
| 79 | Supplying and fixing in position PVC specials such as plain bend, door bend, plain tee, door tee, off sets of various sizes of best approved quality conforming to ISI and providing leak proof joint including fixing to wall etc., complete complying with standard specification.(The specials should be got approved by the Engineer,i/c., before use on work).4" dia PVC ElbowWith ISI Mark |
| 80 | 4" dia PVC Plain TEE with ISI mark |
| 81 | 4" dia PVC Plain Elbow TEE with ISI mark |
| 82 | 3" dia PVC Elbow with ISI mark |
| 83 | 3" dia PVC Door TEE with ISI mark |
| 84 | 3" dia PVC Plain Tee with ISI mark |
| 85 | Providing rain water harvesting pit by earth work excavation in circular shape of 90 cm dia at 100 cm depth. The pit is encased with well ring of 90 cm dia , 30 cm depth, 50 mm thick using RCC 1:2:4 using 20 mm metal for 4 nos. The entire depth ie. 120 cm is filled with 40 mm size metal. The top of the pit is covered with RCC 1:2:4 50mm thick perforated slab including cost and fabrication of reinforcement grills for ring and cover slab, labour charges, cost of materials, moulding curing, finishing and fixing in position etc. complete. |
| 86 | Supplying and fixing in position the following Gun metal gate / wheel valve of best quality and approved make and heavy type quality including cost of cutting, threading of the pipes and fixing of the G.I. pipe in position with white lead, spun yarn etc., complete complying with standard specifications. 50mm dia Gate valve |
| 87 | 32mm dia Gate valve |
| 88 | Supplying and fixing in position best approved quality C.P. brass soap tray of size 150 x 150 mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specification and as directed by the departmental officers |
| 89 | Supplying and fixing in position Indian make decorative type wooden framed Mirror of approved quality and brand of size 600 x 450 mm x 5.5 mm shelf type with necessary ply wood backing, rubber buttons, brass CP screws, T.W. plugs etc. complete complying with standard specification. (The mirror should be got approved by the Departmental Officer before use on woks) |
| 90 | Cement Concrete 1:3:6 (One Cement, three M.Sand and six hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification |
| 91 | Supplying and erecting of 2000 litre capacity PVC Sintex water tank to ISI standard of approved quality and make including labour charges for fixing and fixtures etc. complete. |
| 92 | Supplying and filling 40mm broken brick jelly for septic tank dispersion trench filling including laying, spreading etc., complete with standard specification and as directed by the Engineer,i/c., |
| 93 | Painting new wood work with two coats of synthetic enamel ready mixed paint of approved quality and colour over a priming coat in all floors. The rate is inclusive cost of all materials and labour including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Engineer,,i/c., before use on works). |
| 94 | Varnishing the new wood work two coat with best shellac and with fine best varnish of approved quality varnish over one coat of Bee’s wax of teak wood natural finish including preparation of surface with sand papering including patty priming etc., complete complying with standard specification and as directed by the Engineer,i/c., |
| 95 | Earthwork excavation for foundation in all soils except hard rock requiring blasting inclusive of shoring, shuttering and refilling the foundation with excavated earth in layers of 15mm thick, watered, well rammed etc., complete as directed and depositing the surplus earth within thecompound with initial lead of 10m and initial lift of 2m, levelling the site etc, complete etc., complete complying with standard specifications. Open Excavation. |
| 96 | Providing and laying, spreading and compacting graded stone aggregates to Wet Mix Macadam 250mm thick specification including premixing the materials with water at OMC in mechanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in SubBase / Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5 etc., complete complying with standard specification and as directed by the departmental officers. |
| 97 | Providing and laying 50mm consolidated thick bituminous macadam using 0.20 cum fo 26.50-13.20mm, 0.43 cum of 13.20 2.36 mm and 0.08 cum of 2.36mm & below size IRC metal with 37 Kgs of VG30/VG40 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing the min required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 50mm with mechanical paver to the specified grades and cross section sand consolidated by 8-10 tonne Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, Paver Finisher / 9m paver finisher, Vibratory / Pneumatic roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 504 of MORTH Rev-5 etc., complete complying with standard specification and as directed by the departmental officers. |
| 98 | Providing and laying Tack Coat over WBM/WMM surface (treated with primer) using 2.50Kg of Bitumen Emulsion (RS1) per 10 sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per Clause 503 of MORTH Rev-5 etc., complete complying with standard specification and as directed by the departmental officers. |
| 99 | Providing and laying compacting open graded premix carpet 20mm thick with a liquid seal coat which shall consist of open graded carpet of 20mm thickness in a single course composed of suitable small sized aggregates premixed with bituminous binder (VG30) with application of liquid seal coat for sealing the voids in a bituminous surface conforming to the specifications including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per MORTH Rev-5 (Mix-in-place method). |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
