Public Works Department-PWD has published Tender For Construction Of Residential Complex For Senior Officers At Kavaratti, Lakshadweep(Modified). Submission Date for this Tender is 14-12-2022. Building Work Tenders in kavaratti Lakshadweep. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | STRUCTURAL |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 3 | Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 30 cm girth upto and including 60 cm girth |
| 4 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:All kinds of soil |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 6 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 8 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 9 | Disposal of earth work by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 5 km for all lifts, complete as per directions of Engineer-in-charge. |
| 10 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 11 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 12 | Diluting and injecting chemical emulsion for PRE-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 13 | Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site. |
| 14 | Dry stone pitching 22.5 cm thick laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete. (Payment for Stone to be made separately). |
| 15 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 16 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum. |
| 17 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level. Concrete of M30 grade with minimum cement content of 350 kg /cum. |
| 18 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 19 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 21 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form for all heights :Stairs, (excluding landings) except spiral-staircases |
| 23 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Weather shade, Chajjas, corbels etc., including edges |
| 24 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform |
| 25 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Edges of slabs and breaks in floors and walls. Under 20 cm wide |
| 27 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 28 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 29 | Providing fusion bonded Epoxy coating not less than 175 micron thickness and upto 300 micron to reinforcement barsof any diameteer as per IS-13620-1993/ ASTM-775 M including testing of coating at plant and all taxes etc complete as directed by engineer ion charge. |
| 30 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:5:10 (1 cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size). |
| 31 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge. |
| 32 | Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered): Depth exceeding 1.5 m but not exceeding 3 m |
| 33 | Extra rates for quantities of earth works, executed: In or under water and/or liquid mud, including pumping out water as required Note for item no. 2.24:- The extra percentage rate is applicable in respect of each item but limited to quantities of work executed in these difficult conditions. The unit, namely, metre depth, to be considered for payment, shall be the depth measured from the sub soil water level up to the centre of gravity of the qty executed in difficult conditions. The depth shall be reckoned correct to 0.10 m, 0.05 m or more shall be taken as 0.10 m and less than 0.05 m ignored |
| 34 | Extra for laying concrete in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete The quantity will be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravity of concrete under sub-soil water level with quantity of concrete in cum executed under sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m and less than 0.05m ignored |
| 35 | Extra for laying reinforced cement concrete in or under water and/ or liquid mud, including cost of pumping or bailing out water and removing slush etc., complete The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions. |
| 36 | Extra for laying stone work in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete The quantity will be calculated by multiplying the depth measured from sub-soil water level up to the centre of gravity of stone work under sub - water with the quantity of stone work in cum executed under the sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. |
| 37 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 38 | Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC memberwithout vibration by core cutting (diamond drilling) holes of52mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge. |
| 39 | Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC memberwithout vibration by core cutting (diamond drilling) holes of77mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge. |
| 40 | Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC memberwithout vibration by core cutting (diamond drilling) holes of102mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge. |
| 41 | Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC memberwithout vibration by core cutting (diamond drilling) holes of152mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge. |
| 42 | Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC memberwithout vibration by core cutting (diamond drilling) holes of202mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge. |
| 43 | ARCHITECTURAL |
| 44 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 45 | Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. |
| 46 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 47 | Providing and fixing stainless steel(Grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 48 | 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) |
| 49 | 15 mm cement plaster on the rough side of single or half brick wall of mix : : 1:4 (1 cement: 4 fine sand) |
| 50 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 51 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 52 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 53 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete |
| 54 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 55 | Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre. |
| 56 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Size of Tile 800 x 1600 mm |
| 57 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size.Size of Tile 600 x 600 mm. |
| 58 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Size of Tile 600 x 1200 mm |
| 59 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm |
| 60 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 61 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.50 sqm |
| 62 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 63 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 64 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 65 | 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 66 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 67 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 68 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats |
| 69 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 70 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 71 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to preparethe surface even and smooth complete. |
| 72 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 73 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. |
| 74 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm |
| 75 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm. |
| 76 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 77 | Providing and Fixing, uPVC factory-made, white colour casementLouvers made of extruded profiles. Profiles of frames and sash will be mitred cut and fusion-welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangements for fixing of hardware, EPDM gasket, 1.2 ± 0.2mm thick galvanised steel profile to be included in the required profile, the frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in-charge. The Rates inclusive of 6mm Glazing, Louvers, Locks, hardware hinges, handle and fitting etc. |
| 78 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.Frame size 65 x 100 mm |
| 79 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 35 mm thick |
| 80 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). |
| 81 | Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm). |
| 82 | Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading |
| 83 | :Float glass panes. 4 mm thick glass pane (weight not less than 10kg/sqm). |
| 84 | Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 85 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 86 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood |
| 87 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class teak wood.35 mm thick shutters |
| 88 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 89 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 90 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm |
| 91 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. |
| 92 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 93 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :100X58X1.90 mm |
| 94 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 95 | Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). |
| 96 | Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately). |
| 97 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primeron both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter (600 mm over all girth) |
| 98 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 99 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer"s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work |
| 100 | Finishing with Polyurathane paint system for interiorsusing primer as per manufacturers specifications:Paintingwork with PU Paint of required shade. Two or more coat appliedover an PU coat of primer of approved brand and manufacture. |
| 101 | Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick |
| 102 | Providing and fixing factory made uPVC wooden colour fixed frames comprising of uPVC multichambered frame duly reinforced with1.60 ± 0.2 mm thickgalvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated)G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Glass shall be measured seperately |
| 103 | Providing material and labour for fixing 10mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid. |
| 104 | Labour charges for moulding ornamantal designs on RCC columns with cement mortar in smooth finish and curing till the required period etc complete as per instruction of Engineer-In-Charge |
| 105 | Supplying and fixing GFRC (Glass Fibre Reinforced Concrete) single skin panels of approved make and design for ornamental column work with stiffened ribs mechanically linked to steel stud frame, permanent form work or shuttering with projection cast in tiles. The weight per unit GRC or its surface mass, stiffeners provides a property of noise insulation at lower frequencies (typical 10mm thick GRC having surface mass 20kg/m2 will have an average sound reduction of about 30 decibel). Various surface finishes and shades such as plain or sandstone, striped granite, oak finish, stonewall and acid wash, etc. can be obtained. Including cost and conveyance of all materials site, labour charges transportation , installation charges,scaffolding etc. Over RCC columns or steel stud frame |
| 106 | Supplying and fixing GRC (Glass Fibre Reinforced Concrete), with single skin panels with stiffened ribs mechanically linked to steel stud frame, permanent form work or shuttering with projection cast in tiles. The weight per unit GRC or its surface mass, stiffeners provides a property of noise insulation at lower frequencies (typical 10mm thick GRC having surface mass 20kg/m2 will have an average sound reduction of about 30 decibel). Various surface finishes and shades such as plain or sandstone, striped granite, oak finish, stonewall and acid wash, etc. can be obtained. Including cost and conveyance of all materials site, labour charges transportation , installation charges,scaffolding etc. |
| 107 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover |
| 108 | Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area |
| 109 | Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured). |
| 110 | Providing and fixing ball bearing for rolling shutters. |
| 111 | Providing material and labour for laying Porcelain Mosaic tiles of make by piccolo, Italia or Equivilantin different sizes (25mm x 25mm/ 50mm x 50mm/ 100mm x 100mm) having 8 mm thicknesswith water absorption less than 0.08% and conforming to IS: 15622, in anycolours and shade, in Water body, skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints for al depth al level as directed by engineer in charge. The Glass mosaic tile shall be fixed as per approved pattern and design. Sample to be approved by Architect. |
| 112 | INTERIOR |
| 113 | Providing and fixing Gypsum false ceiling (12.5 mm) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks) |
| 114 | Providing & fixing 8 mm thick Calcium Silicate false ceilingat all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture"s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. |
| 115 | Providing & Installation of wooden ceiling made up ofsecond class teak planks with necessary wooden frame work fixed with necessary fittings as required for holding panels with groves etc complete as per requirments etc. As per design approved by architects. |
| 116 | Providing and fixing wooden trap doors for access to the areas above false ceiling. The trap door shall have an external frame made of 2" x 2" Teakwood scantling on which the shutter is hinged. Shutter shall be made 12mm thick solid core flush shutter with timber edge lipping as per the detail drawings. Concealedhinges shall be used to mount the shutters and locking shall be provided with panel locks. The shutter shall be molded in level with the false ceiling forming a groove all around. Sufficient number of hinges and locks shall be provided to avoid sagging of the shutter. Key also shall be supplied. No extra rate shall be provided for suspenders or frame works all-round for linking the trap door tofalse ceiling, as per design approved by architects. |
| 117 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 118 | WALL PANELLING |
| 119 | Providing and fixing of wall panelling with 19 mm thick 710 BWP fire retardant plywood conforming to IS: 5509 /10701 grade internal frame work over which 12 mm thick 710 BWPfire retardant plywood is fixed on. Exposed area finishing with 12.5mm thick gypsum board as per design approved by Architects. |
| 120 | SOFT FURNISHING |
| 121 | BEDDING |
| 122 | Supplying and fixing of Mattress (6")- breathable bonded foam core with HR foam layer on either sides, both sides usable- medium firm |
| 123 | Supplying and fixing of Mattress Protector - King (Size:78"x72"), of 100% Water Proof Terry Top , with Fitted Sheet. |
| 124 | Supplying of Bed sheet - King (Size: 112"x116"), of 100% Cotton-250 - 400 -60S-Percale, White |
| 125 | Supplying of Duvet cover - king (Size: 104"x94"), of 100% Cotton-250to 400 tcc-60S- 1 CM Satin Stripe, White |
| 126 | Supplying of Duvet-Quilt- King (Size: 102"x92"), 300 GSM-Super Soft Filling-Quilted-Polyester Micro Fabric Shell |
| 127 | Supplying of Pillow Cover - Large (Size: 20"x37"), Bag Type-100% Cotton-60S-300 TC-1 CM-SatinStripes |
| 128 | Supplying of Pillow Cover - Regular(Size: 20"x30") , Bag Type-100% Cotton-60S-300 TC-1 CM-SatinStripes |
| 129 | Supplying of Pillows - Large (Size:20"x36"), Denier Fibre 1.5 Filling-500Grams |
| 130 | Supplying of Pillows - Regular (Size:20"x30"), Denier Fibre 6 Filling-500Grams |
| 131 | Supplying of Pillow Protector - Large (Size:20"x37"), 100% Water Proof Terry Top - Zipper Closure |
| 132 | Supplying of Pillow Protector - Regular (Size:20"x30"), 100% Water Proof Terry Top - Zipper Closure |
| 133 | Supplying of Cushions ,Designer Fabric + Poly Fill Cushions (Size:16"x16") |
| 134 | CURTAINS |
| 135 | Supplying and fixing of Main curtain,with polyester based cotton blend pleated curtains. Including all fixing charges and necessary fittings. |
| 136 | Supplying and fixing of Sheer curtain,of polyester based cotton blend pleated curtain. Including all fixing charges and necessary fittings. |
| 137 | Supplying and fixing of roller blinds,Including all fixing charges and necessary fittings. |
| 138 | RUGS |
| 139 | Supplying and laying high grade of rugs for bedrooms of size 150x250cm. |
| 140 | Supplying and laying high grade of rugs for formal living room of size 300x250cm. |
| 141 | FIXED FURNITURES |
| 142 | Providing and fixing 600mm wide Pantry unit made with 710 grade prelaminated plywood in approved wooden laminate on shutters and all visible areas. Best quality telescopic sliders,hinges,locks,hardware to be provided. (HETTICH/DORMA/HAFELE OR EQ) as per drawing and 3D.counter top laid with steel grey granite with bullnose rounded edge . |
| 143 | Providing and fixing 600mm wide wardrobe consists of carcase with both side leather laminate pressed 19mm thick BWP 710 gradeplywood with 2mm thick edge band with profile lighting at hanging space, end panel with 40mm thick end panel using 19mm thick plywood with 4mm thick ash veneer and wooden edge band, back panel with both side leather laminate pressed 12mm thickBWP 710 grade plywood, flutted wooden shutters, drawers fitted with smooth glides and lock. The cost shall include the price for auto closed self closing hinges, ss ball bearing telescopic slide/ drawer channel, drawer lock with two reversible keys, 10mm dia ss satin finish pull handles & 15mm dia dress hanging rod, all complete as specified and as directed by the Engineer-in-Charge |
| 144 | Providing and fixing 600mm wide dress rack consists of carcase with both side leather laminate pressed 19mm thickBWP 710 gradeplywood with 2mm thick edge bandend panel using 19mm thick plywood with 4mm thick ash veneer and wooden edge band, back panel withlaminate pressed 12mm thickBWP 710 grade plywood,wooden shutters, drawers fitted with smooth glides and lock. The cost shall include the price for auto closed self closing hinges, ss ball bearing telescopic slide/ drawer channel, drawer lock with two reversible keys, 10mm dia ss satin finish pull handles & 15mm dia dress hanging rod, all complete as specified and as directed by the Engineer-in-Charge |
| 145 | Providing,supplying & fixing of TV unit of fixed furniturewith the Carcase of 18mm thick BWP Green Club plywood or hardwood frame wih 4mm tk Ash veneer.Top & legs shall be made up of Ashwood. exterior portion finished with veneer and interior portion finished with laminate.All exposed faces finished with PU polish for wood frames . |
| 146 | Providing ,supplying & fitting of vanity counters/ wash basin counters with cabinets of carcase with 19mm tk BWP 710 grade plywood with laminate finish &wooden edge band,16mm tk BWP 710grade pywood shutters with self closing hinges. counter top with granite or fullbody tile laid over 8 mm thick multiwood board, with cement based high polymer modified quick set adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete allas directed by the Architect.Extra for providing opening of required size & shape for wash basin, vanity counter and similar location ingranite or fullbody tile ,including necessary holes for pillar taps etc.Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer"s specifications including appropriate priming coat, preparation of surface, etc. on complete steel work |
| 147 | Providing & supplying of Mirror (600mmx900mm) fixing in toilet, above Toilet wash counter to provide 6mm edge polished mirror fixed with mirror stud. |
| 148 | Supplying and fixing make wall to wall shower enclosure with one fixed glass 1- part. Glass partitions using 8mm thick Toughened glass with necessary hardware fittings in Chrome finishwith 1 Top Channel, 1 Wall Profile, 2 Magnet Profile, , 1 Damn strip on the bottom, 1 fixed panel glass as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware. As per design approved by architects. |
| 149 | Supplying and fixing one sliding door using 8mm thick Toughened glass with necessary hardware fittings in Chrome finishwith 1 Top Channel, 1 Magnet Profile, 1 Door knob, 1 Damn strip on the bottom, 1 guider for smooth sliding passage, Rollers : ball bearing encapsulated in brass should be concealed in the top channel, 1 Sliding Glass as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware. As per design approved by architects. |
| 150 | Providing & fixing kitchen/workarea table and the base & legs shall be made up ofplywood ,exterior and interior portion finished with laminate ,also providing drawer cabinet with slides locking arrangement,use necessary hardware like handles,accessories etc. All exposed faces finished with PU polish for wood frames . |
| 151 | Providing & fixing coffee shop table and the base & legs shall be made up of shall be made up ofplywood ,exterior and interior portion finished with laminate ,also providing drawer cabinet with slides locking arrangement,use necessary hardware like handles,accessories etc. All exposed faces finished with PU polish for wood frames |
| 152 | MOVABLE FURNITURES |
| 153 | Providing & fixing of 200x200 cm King size cot with base, legs & frame works made up of Ashwood or hardwood furniture and provided with fabric headboard of imported fabric andprovided with povision for10" mattresses. and having finished with matching finish orwalnut finish.All exposed faces finished with PU polish for wood frames . |
| 154 | Supply & fixing45x45x55cm bedside Table with 2drawers & 2 knobs and the base & legs shall be made up of of 18mm thickBWP Green Club Plywood or hardwood framework with 4mm thick ash veneer & legs shall be made up of ashwood and havingwallnut finish polish and accessories having hinges of Hettich brand.All exposed faces finished with PU polish for wood frames . |
| 155 | Providing & fixing 90x40x15 cm study table with the Carcase of 18mm thick BWP Green Club plywood or hardwood frame wih 4mm tk Ash veneer.provided with two shutters and havingwalnut finish polish. exterior and interior portion finished with veneer ,also providing drawer cabinet with slides locking arrangement,use necessary hardware like handles,accessories etc. All exposed faces finished with PU polish for wood frames . |
| 156 | Providing, supplying & fixing of study chairs and frame & legs are made up of Ashwood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric. |
| 157 | Providing & fixingTeapoy of 35cm dia and the topshall be made up of Ashwood & legs shall be made up of Ashwood or hardwood having matching finish or walnut finish ploish.All exposed faces finished with PU polish for wood frames . |
| 158 | Providing & fixing balcony chair made up of wood frame having PU finish, provided with seat cushion made of 5 inches. The seat cushion is made of 5 inches polyurethane foam of density 32 kg/m3 & the backrest has a 3 inch polyurethane foam of density 32kg/m3 supported with 75mm jute strips. The polyster polyfill keeps the upholstery wrinke free and soft. Outer finish :- the outer finish has a superior quality water resistant fabric stitched with nylon bonded thread and stained solid wooden legs. All exposed faces finished with PU polish forwood frames. All inner surfaces will be finished with natural french polish. |
| 159 | Supply & fixing dining unit 180x90cm 8 seater capacity Table made up of Ash or hardwood with matching finish or walnut finish. The table top shall be provided with glass top. Table to be made complete as per the drawing and details. All exposed faces finished with PU polish for wood frames . |
| 160 | Providing, supplying & fixing of dining chairs,frame & legs are made up of Ash or hardwood having matching finish or walnut finish ploish.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric of Italian leather.All exposed faces finished with PU polish for wood frames. |
| 161 | Providing & fixingCenter table and the topshall be made up of 18mm thick BWP Green club plywood or hardwood framework with 4mm thick ash veneer & legs shall be made up of ashwood and having Light wallnut finish polish. |
| 162 | Providing & fixingsingle seater sofa with dimension -1200 mm Width x 950 mm Depth x 950 mm Height.Frame shall be made of combination of 12 mm moisture resistance and termite free plywood and pine wood (without knot)having cross section 34x64mm.Seat - shall be made of slab stock foam of density of base 28 kg/ meter cube and super soft 32 kg/meter cube at top. Seatshall be embeded with 2mm pocket spring.Seat Back - made of slab stock foam of density 28 kg/ meter cube pasted on back. Front of the back rest shall be made ofloose conjugated polyester fiber webbing.Legs - legs shall be made of rubber wood.Facia - facia of the sofa shall be made of membrane pressed MDF. |
| 163 | Providing & fixing2 seater sofa with dimension -1490 mm Width x 950 mm Depth x 950 mm Height.Frame shall be made of combination of 12 mm moisture resistance and termite free plywood and pine wood (without knot)having cross section 34x64mm.Seat - shall be made of slab stock foam of density of base 28 kg/ meter cube and super soft 32 kg/meter cube at top. Seatshall be embeded with 2mm pocket spring.Seat Back - made of slab stock foam of density 28 kg/ meter cube pasted on back. Front of the backrest shall be made ofloose conjugated polyester fiber webbing.Legs - legs shall be made of rubber wood.Facia - facia of the sofa shall be made of membrane pressed MDF. |
| 164 | Providing & fixing3 seater sofa with dimension -2040 mm Width x 950 mm Depth x 950 mm Height.Frame shall be made of combination of 12 mm moisture resistance and termite free plywood and pine wood (without knot)having cross section 34x64mm.Seat - shall be made of slab stock foam of density of base 28 kg/ meter cube and super soft 32 kg/meter cube at top. Seatshall be embeded with 2mm pocket spring.Seat Back - made of slab stock foam of density 28 kg/ meter cube pasted on back. Front of the back rest shall be made of loose conjugated polyester fiber webbing.Legs - legs shall be made of rubber wood.Facia - facia of the sofa shall be made of membrane pressed MDF. |
| 165 | Providing & fixingMedia console with the Carcase(1500mm x 450mmx450mm) of 18mm thick BWP Green Club plywood or hardwood frame wih 4mm tk Ash veneer with matching finish or walnut finish. Top & legs shall be made up of Ashwood.provide drawer cabinet with slides locking arrangement,use necessary hardware like handles.All exposed faces finished with PU polish for wood frames . |
| 166 | Providing & fixing 180x80x80 cm Office table and the topshall be made up of 18mm thick BWP Green club plywood or hardwood framework with 4mm thick ash veneer and having wallnut finish polish.All exposed faces finished with PU polish for wood frames. |
| 167 | Providing, supplying & fixing of office chairs with wheels and frame made up of Ash or hardwood furniture with matching finish or walnut finish.seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam. The complete back is contoured to provide the needed lumbar support for long seating hours. The seat is made up of moulded foam, upholstered with fabric.ARMRESTS: The Arm rest is injection moulded in Polypropylene fitted to the seat base . SYNCHRO MECHANISM: The mechanism installed for this chair is a Synchro-1 mechanism. This mechanism provides you with the utmost comfort while leaning backwards. There is a displacement in the ratio of 1:3 between seat and back respectively The Synchro mechanism is designed with 360 Degree revolving feature, Tilt tension adjustment and Upright locking. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12 cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal is made of nylon with glass reinforcement and fitted with 5 nos. twin wheel castors.(castor wheel dia. 5.0cm.) TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in 30% Glass Filled black Nylon. Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric.All exposed faces finished with PU polish for wood frames . |
| 168 | Providing, supplying & fixing of visitors chairs and frame & legs are made up of Ash or hardwood having matching finish or walnut finish ploish.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric or Italian leather. |
| 169 | Supply & fixing dining unit 180x90cm 8 seater capacity Table made up of Ash or hardwood with matching finish or walnut finish. The table top shall be provided with glass top. Table to be made complete as per the drawing and details. All exposed faces finished with PU polish for wood frames . |
| 170 | LANDSCAPING |
| 171 | Procuring healthy grass free from weeds and foreign materials and laying on the soil medium as turfing,the rate include for grass cost, transport to site, cost and application of manure, planting, labour, supervision and maintenance for 2 months after planting Pearl Grass |
| 172 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Royal palm |
| 173 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Foxtail palm |
| 174 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Bismarkia palm |
| 175 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Jackfruit tree |
| 176 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Elenji tree |
| 177 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Coconut tree |
| 178 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Malpighia Topiary in steel mesh |
| 179 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Eugenia Topiary |
| 180 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Clerodendrum Inerme -Hedge |
| 181 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Murraya Exotica - Flower bush |
| 182 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Heliconia Caribea |
| 183 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Areca tree |
| 184 | Supplying , stacking and spreading sludge / well decayed farm yard manure from thesource,Mixing earth and manure or in proportion specified or directed, Spreading ofdung manure or / and good earth in required thickness.and fine dressing the ground as per natural gradiantapproved by the engineer in charge incl. screening, loading, unloading, conveyance and stacking at site. |
| 185 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 |
| 186 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-inCharge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 187 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin-charge). |
| 188 | Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-incharge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete. New work (Two or more coats) |
| 189 | Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 190 | 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 191 | Providing and applying antiskid epoxy of minimum 1mm thickness with UV resistant PU top coat and marking court lines with UV resistant paint.The work includes surface preparation with a suitable floor grinder, vacuuming dust from floor, priming the surface with epoxy floor primer,afterfilling cracks with epoxy grout ,proper mixing of epoxy paint components and applying etc all complete as per manufacturer"s specifications and instruction of Engineer in charge |
| 192 | ELECTRIFICATION |
| 193 | WIRING |
| 194 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required Group C |
| 195 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 196 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 197 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 198 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 199 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 200 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair |
| 201 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 202 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm |
| 203 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm |
| 204 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm |
| 205 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch |
| 206 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch |
| 207 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet Each |
| 208 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet |
| 209 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet |
| 210 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet |
| 211 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 212 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 213 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm) |
| 214 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 215 | Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored) |
| 216 | MCCB, MCB & DB’S |
| 217 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door |
| 218 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required. 12 way (4 + 36), Double door |
| 219 | Supplyingandfixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,miniaturecircuitbreaker suitableforinductiveloadoffollowing poles in the existingMCB DB complete with connections, testing and commissioning etc. as required. Single pole - 5 to 32 A |
| 220 | Supplyingandfixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,miniaturecircuitbreaker suitableforinductiveloadoffollowing poles in the existingMCB DB complete with connections, testing and commissioning etc. as required. Triple pole - 5 to 32 A |
| 221 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A |
| 222 | Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A |
| 223 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 224 | Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 225 | CABLE TRAYS |
| 226 | Hot Dipped Galvanized Iron Cable Tray |
| 227 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness |
| 228 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness |
| 229 | EARTHING |
| 230 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 231 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 232 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 233 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 234 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) |
| 235 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 236 | Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. |
| 237 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 238 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 239 | MV CABLE LAYING |
| 240 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Upto 35 sq. mm |
| 241 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 35 sq. mm and upto 95 sq. mm |
| 242 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 95 sq. mm and upto 185 sq. mm |
| 243 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 244 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 245 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 246 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) |
| 247 | HT CABLE LAYING |
| 248 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. Above 120 sq. mm and upto 400 sq. mm |
| 249 | MV CABLE JOINTING & END TERMINATION |
| 250 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm) |
| 251 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm) |
| 252 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm (57mm) |
| 253 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 400 sq. mm (82mm) |
| 254 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 10 sq. mm (25mm) |
| 255 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (28mm) |
| 256 | HV CABLE JOINTING & END TERMINATION |
| 257 | Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 300 sq. mm |
| 258 | MCCB, MCB & DB’S |
| 259 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way (4 + 36), Double door |
| 260 | Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 100 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having charectorstic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed (i) 63 Amps. FP. |
| 261 | WIRING |
| 262 | Wiring for light point/ fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copperconductorsingle core cable in surface / recessedmedium class PVC conduit,with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm.FRLS PVCinsulatedcopper conductor single core cable etc. as required for; Two light controled by one switch. |
| 263 | Wiring for light point/ fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copperconductorsingle core cable in surface / recessedmedium class PVC conduit,with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm.FRLS PVCinsulatedcopper conductor single core cable etc. as required for; Three light controled by one switch. |
| 264 | Wiring for light point/ fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copperconductorsingle core cable in surface / recessedmedium class PVC conduit,with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm.FRLS PVCinsulatedcopper conductor single core cable etc. as required for; Four light controled by one switch. |
| 265 | Light Fixtures |
| 266 | Supply of Light Fixtures/Ceiling Fans/Exhaust Fans |
| 267 | 12W Recessed Down Light |
| 268 | 12W Surface Down Light |
| 269 | 10W Mirror Light |
| 270 | 12W Wall Light |
| 271 | 3W Wall Light |
| 272 | 20W LED Tube Light |
| 273 | 4.5W Led Strip including LED drive |
| 274 | 18W Led Chandelier |
| 275 | Geyser |
| 276 | 6W Led Hanging Light |
| 277 | Bollard Lights (Civil works including) |
| 278 | 6M Pole& 50W LED Flood Light with necessary arms for light fixtures (Civil works including) |
| 279 | 50W Flood Light |
| 280 | 4M Pole& 20W LED Light fixtures (Civil works including) |
| 281 | RMU |
| 282 | 11kV/433v,400KVA USS |
| 283 | SITC of 400KVA USS : 1 No. Indoor 11kv,630A, 26.3 kA for 1 sec Load Break Switch Panel consist ofmechanical / electrical Trip bush button ,ON/OF Indicator ,Space heater with thermostat , 230V AC shunt trip coil HT HRC Fuses links with Aluminium busbar and copper earthing strip, on HVside Rigid Bus Bar interonnection to the TransformerCompletewithallinterconnection , powder coatedapproved color control wiring,earth bus ofadequate capacity & double earthing to all breakersetc.as per ElectricalInspectorate / KSEB Standards.Transformer comprising of :11kV/433V ,400KVA ,50Hz,3phase,Vector Dyn 11 Resin Cast Indoor Transformer with off circuit tapping+5% to -5% in steps of 2.5% with winding temperature indicator and hooter with allstandard accessories as per IS 2026/77 on HV side Rigid Bus Bar interonnection to the 11KV LBS Panel and on LT side cable boxsuitable for 3 x 3.5 x300 sq.mm XLPE Al ; cablewith all standard fittings and accessories.Painting shall be carried out as per IS 631, impedance ofthe transformer shall be as per relevant standards. HT CABLES |
| 284 | GENERATORS |
| 285 | SITC of D.G. set of following KVA 0.8 P.F.3 phase,50c/s,433V, comprising diesel engine, fuel tank, base plate,antivibration pad,battery, batterylead wire, battery charger self startingand self charging mechanism,and residential type silencer, control panel , in accoustic enclosure etc.with all standard accessoriesas per ElectricalInspectoratestandards and pollutioncontrol boardnorms. 160 KVA |
| 286 | L.T.PANELS |
| 287 | SITC of cubicle type mediumvoltage switch boards as per specificationsmentioned below, comprising ofACBs / MCCBs.,enclosed in 16 guage M.S.cubicle complete with angle iron frame work,panel doors , horizontal andvertical busbars and outgoing feeders,FRP separators, phase barriers,gaskets for door,feeders designations, etc.,Main Switch Board shall be capable of withstanding 50 KA fault level. The panelshall be suitable for erection on the floor using channel and fastners at regular intervals. ( Panel should confirm to BIS,IE rules,KSEI/ KSEB Standards) MAIN MV PANEL |
| 288 | SITC of cubicle type mediumvoltage switch boards as per specificationsmentioned below, comprising ofACBs / MCCBs.,enclosed in 16 guage M.S.cubicle complete with angle iron frame work,panel doors , horizontal andvertical busbars and outgoing feeders,FRP separators, phase barriers,gaskets for door,feeders designations, etc.,Main Switch Board shall be capable of withstanding 50 KA fault level. The panelshall be suitable for erection on the floor using channel and fastners at regular intervals. ( Panel should confirm to BIS,IE rules,KSEI/ KSEB Standards) METERING PANEL 1 TO 4 |
| 289 | SITC of cubicle type mediumvoltage switch boards as per specificationsmentioned below, comprising ofACBs / MCCBs.,enclosed in 16 guage M.S.cubicle complete with angle iron frame work,panel doors , horizontal andvertical busbars and outgoing feeders,FRP separators, phase barriers,gaskets for door,feeders designations, etc.,Main Switch Board shall be capable of withstanding 50 KA fault level. The panelshall be suitable for erection on the floor using channel and fastners at regular intervals. ( Panel should confirm to BIS,IE rules,KSEI/ KSEB Standards) SSB COMMON |
| 290 | SITC of cubicle type mediumvoltage switch boards as per specificationsmentioned below, comprising ofACBs / MCCBs.,enclosed in 16 guage M.S.cubicle complete with angle iron frame work,panel doors , horizontal andvertical busbars and outgoing feeders,FRP separators, phase barriers,gaskets for door,feeders designations, etc.,Main Switch Board shall be capable of withstanding 50 KA fault level. The panelshall be suitable for erection on the floor using channel and fastners at regular intervals. ( Panel should confirm to BIS,IE rules,KSEI/ KSEB Standards) EXTERNAL LIGHTING PANEL |
| 291 | Supplying of following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm |
| 292 | Supplying of following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm |
| 293 | Supplying of following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm |
| 294 | Supplying of following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 400 sq. mm |
| 295 | Supplying of following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 10 sq. mm |
| 296 | Supplying of following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm |
| 297 | Supplying/Laying/Terminating of following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 X 2.5 sq. mm |
| 298 | ELV WORKS |
| 299 | CCTV SYSTEM |
| 300 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable |
| 301 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm |
| 302 | CCTV SYSTEM |
| 303 | Supply, Installation,testing and commissioning of IR Varifocal Dome Camera with below specifications as minimum and with all the necessary accessories for the installation. 4 MP Resolution, 2.8/3.6 mm lens, H.264/H.265, 20 meters IR range, DWDR, Built-in IR LED,IP66, 3DNR, white balance, Privacy mask, BLC, HLC , Camera tampering detection, manual trigger, motion detection, periodical trigger, recording notification, 2 video Streams |
| 304 | Supply, Installation,testing and commissioning ofOutdoor type IR Bullet Camera with below specifications as minimum and with all the necessary accessories for the installation 4 MP Resolution, 2.8/3.6 mm lens, H.264 / H.265, 30 meters IR range,DWDR, Built-in IR LED, IP66, 3DNR, white balance, Privacy mask, BLC, HLC, Camera tampering detection, manual trigger, motion detection, periodical trigger, recording notification, 2 video Streams |
| 305 | Supply, Installation,testing and commissioning of following Channel NVR with below specifications as minimum and with all the necessary accessories for the installation 32 Channel IP Cameras support, 4 SATA Ports ( Loaded with HDD for 60 days storage), Maximum users - 20 or higher, IR Range of 100 Mtr, Ptotocols - HTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS, IP Filter, DDNS, FTP, SNMP, IP Search , ONVIF 2.4, SDK, CGI trigger Events - recording, PTZ, Tour, Alarm out, video Push, Email, FTP, Snapshot, Buzzer & Screen tips, recording Mode - manual, Schedule (Regular, Continuous), MD (video detection: motion detection, tampering, video Loss), Stop, Bandwidth - 200 Mbps, ONVIF 2.0 |
| 306 | Supply, Installation,testing and commissioning of following Channel NVR with below specifications as minimum and with all the necessary accessories for the installation 16 Channel IP Cameras support, 4 SATA Ports ( Loaded with HDD for 60 days storage), Maximum users - 20 or higher, IR Range of 100 Mtr, Ptotocols - HTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS, IP Filter, DDNS, FTP, SNMP, IP Search , ONVIF 2.4, SDK, CGI trigger Events - recording, PTZ, Tour, Alarm out, video Push, Email, FTP, Snapshot, Buzzer & Screen tips, recording Mode - manual, Schedule (Regular, Continuous), MD (video detection: motion detection, tampering, video Loss), Stop, Bandwidth - 200 Mbps, ONVIF 2.0 |
| 307 | Supply, Installation,testing and commissioning of following Channel NVR with below specifications as minimum and with all the necessary accessories for the installation 8 Channel IP Cameras support, 4 SATA Ports ( Loaded with HDD for 60 days storage), Maximum users - 20 or higher, IR Range of 100 Mtr, Ptotocols - HTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS, IP Filter, DDNS, FTP, SNMP, IP Search , ONVIF 2.4, SDK, CGI trigger Events - recording, PTZ, Tour, Alarm out, video Push, Email, FTP, Snapshot, Buzzer & Screen tips, recording Mode - manual, Schedule (Regular, Continuous), MD (video detection: motion detection, tampering, video Loss), Stop, Bandwidth - 200 Mbps, ONVIF 2.0 |
| 308 | Supply, Installation, Testing and Commissioningof LED Displays 32"for CCTV Monitoring with all the necessary wall mounting accessories with HDMI Cable |
| 309 | Supply, Installation, Testing and Commissioningof LED Displays 22"for CCTV Monitoring with all the necessary wall mounting accessories with HDMI Cable |
| 310 | DATA SYSTEM |
| 311 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable |
| 312 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm |
| 313 | DATA SYSTEM |
| 314 | Supplying & erecting M.S. box having 16 Gauge painted with red oxide or heavy duty PVC box erected flushed on wall or concealed in wall with necessary plastering & finishing as directed of following size. 100mm x 100mm x 75mm (d) |
| 315 | Providing following type of Modular Type Accessories mounted with pvc/metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (8) Modem Jack for Computer Open RJ-45. |
| 316 | LIFT INSTALLATION |
| 317 | PASSENGER LIFT |
| 318 | Supply and Erection, testing and commissioning of Hydraulic Paasenger Lift (as per Technical specification) G+1 |
| 319 | Design, manufacture, supply, installation, testing and commissioning of Gearless, machine room less Passenger lifts of capacity 8 passengers for (G+2) storeyed Building with the following specifications: Location of Lifts : Inside the building i) Speed : 1.5 MPS ii) Floors : 3 floors (GF+FF+SF) iii)Travel : 9.00 Mtrs (approx.) iv) Stops & opening 3 stops & 3 openings v) Controller: Microprocessor based variable Frequency Regenerative closed loop. vi) Automatic rescue device complete with dry maintenance free batteries as required. vii)Operation: Microprocessor based single automatic push button/ simplex selective collective/ duplex collective selective with/ without attendant viii)Power – 415 V, 3 phase, 50 Hz, 4 wires system ix) Type of doors a) Car : Power operated centre opening horizontal sliding stainless steel scratch proof (Honey Combing finish) b) Landing doors: Stainless Steel with Honey Combing Finish. c) Flooring: Granite Flooring. VVVF drive control for constant load of 884 Kg respectively traveling @ 1.5 mps with Simplex operation with out attendant, car position indicators, battery operated alarm bell and emergency light, power operated centre opening automatic sliding stainless steel doors for car entrance and hoistway entrance etc. including all steel, civil and electrical materials as specified such as machine beams, buffer support channels, facia plates, landing sills, pit ladder metal screen in elevator pit etc., as per the specification including cost of all civil and electrical works required for installation of elevator in the existing lift well and machine room, scaffolding, cutting holes, grouting and making good to damages in wall, floor, ceiling etc. for fixing accessories, foundation bolts etc., hoistway wiring and other associated Wirings including Fireman’s switch complete in all respect as per direction of Engineer-in-charge" G+2 |
| 320 | HVAC SYSTEM |
| 321 | Supplying & installing M.S powder coated standard type stand mounting for outdoor unit of split A.C up to 2TR Capacity, erected with necessary hardware materials as irected. 1.75 kg for 1 set (8-3-3/151) |
| 322 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation |
| 323 | Providing and erecting 3 star and above rated approved make split air – conditioning unit consisting of condensing unit with fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of proper insulated copper tubing up to 5 RMT suitable for (Cost includes M.S. Stand, Gas Charging & Internal Copper Wiring Remote Control). For 1.5 ton capacity. |
| 324 | Providing and erecting 3 star and above rated approved make split air – conditioning unit consisting of condensing unit with fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of proper insulated copper tubing up to 5 RMT suitable for (Cost includes M.S. Stand, Gas Charging & Internal Copper Wiring Remote Control). For 2 ton capacity. |
| 325 | Providing and erecting 3 star and above rated approved make split air – conditioning unit consisting of condensing unit with fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of proper insulated copper tubing up to 5 RMT suitable for (Cost includes M.S. Stand, Gas Charging & Internal Copper Wiring Remote Control). For 3 ton (2 x 1.5 ton) multi split unit. |
| 326 | Providing and erecting 3 star and above rated approved make split air – conditioning unit consisting of condensing unit with fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of proper insulated copper tubing up to 5 RMT suitable for (Cost includes M.S. Stand, Gas Charging & Internal Copper Wiring Remote Control). Remote control (b) Cordless remote control. |
| 327 | PHE SYSTEM |
| 328 | A. SANITARY FIXTURES. |
| 329 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Make : Queo Neo Marsala/K-16321IN-SS-0/ OR Equ. |
| 330 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 331 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 332 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 333 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effectiveheight of 88 mm, weighing not less than 190 gms. |
| 334 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 335 | Providing and fixing toilet paper holder : C.P. brass |
| 336 | B. SOIL, WASTE, VENT & RAIN WATER PIPES |
| 337 | Supplying, Fixing, testing and commissioning at site SDR-11 gradeChlorinated Polyvinyl chloride (CPVC)pipes confirming to ASTM D:1785 & CPVC fittings suitable for solvent welded joints, including all necessary fittings like Tee, Elbow, Adaptors, etc, Chasing and making good the walls wherever required, providing necessary brass ended terminal fittings (For Condensate A/c drain) 20 mm ID (¾’’) dia (Concealed) |
| 338 | Supplying,fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (For A/C drain) |
| 339 | C. WATER SUPPLY (INTERNAL AND EXTERNAL) |
| 340 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work - Exposed on wall ¾ ""(20mm) dia. (Exposed on wall /ceiling) Cold water supply |
| 341 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work - Exposed on wall 1 ""(25mm) dia. (Exposed on wall /ceiling) Cold water supply |
| 342 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. ¾ ""(20mm) dia. (Internal / Concealed)water supply |
| 343 | Supplying, fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (For CPVC). ½ ""(15mm) dia. |
| 344 | Supplying, fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (For CPVC) ¾ ""(20mm) dia. |
| 345 | Supplying, fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (For CPVC) 1 ""(25mm) dia. |
| 346 | Supplying, fixing, testing Micro cellular closed cell Nitrile rubber elastomeric insulation(UL-94 Approved) tubes/sheets (9mm thick) for the hot water supply pipes with protective glass fabric & co-extruded polymeric covering for UV & mechanical protection. (For CPVC) 1¼ ""(32mm) dia. |
| 347 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work -(Internal /External/ In shaft) 1” (25mm)dia (External / in Shaft) |
| 348 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work -(Internal /External/ In shaft) 1¼”(32mm)dia(External / in Shaft) |
| 349 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work -(Internal /External/ In shaft) 1 ½” (40mm) dia(External / in Shaft) |
| 350 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. as per direction of Engineer in Charge. Internal work -(Internal /External/ In shaft) 2” (50mm) dia(External / in Shaft/Ring/ pump out) |
| 351 | Supplying,Fixing, testing and commissioning at site in positions Automatic Air Release Valves, ball valves of approved quality and make on the top of the vertical water supply pipes as per specification and drawings 1"(25mm) dia |
| 352 | Supplying,Fixing at site in position full way lever operated forged brass gate valve of brass body with forged brass hard crome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings 1” (25mm)dia |
| 353 | Supplying,Fixing at site in position full way lever operated forged brass gate valve of brass body with forged brass hard crome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings 1 ¼ “ (32mm) dia. |
| 354 | Supplying,Fixing at site in position full way lever operated forged brass gate valve of brass body with forged brass hard crome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings 2” (50mm) dia |
| 355 | NON RETURN VALVE cast Iron double flange as per IS/5312 PN 1.6 rating complete with Bronze body & wedge Stainless Steel spindle, Gland packing, Rubber gasket 2 ” (50mm) dia |
| 356 | D.EXTERNAL SEWERAGE |
| 357 | Excavation in soil upto a depth of 1500mm Including backfilling in layers, consolidating and disposing of surplus earth up to a distance of50mts. |
| 358 | Cement concrete 1:5:10 (I cement 5 sand and 10 broken stones) encasing using 20 mm granite broken stones for concreting horizontal pipes in the trenches,hire and labour charges for form work ,watering for curing etc complete as per the satisfaction of the Project Manager including cost of all materials. |
| 359 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : |
| 360 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : |
| 361 | Supplying and fixing Ductile Iron (Hinged Type) cover and frame. (As per EN – 124 standard) For Ovrhead Tank 450X450mmlight dutyweight not less than 58kg. -A-15 (LD) |
| 362 | Supplying and fixing Ductile Iron (Hinged Type) cover and frame. (As per EN – 124 standard) For Sump Tank 600X600mmsize medium dutyweight not less than 58kg. -A-15- (LD) Supplying |
| 363 | A. SANITARY FIXTURES. |
| 364 | Fixing, Testing and Commissioning at site Wall Mounting type water closet with P trap & its all fittings like rag bolts, solid plastic Seat cover etccomplete including cutting and making good the walls and floors wherever required,Concealed flushing cisternwith brass screws,nuts , and washers complete including cutting and making good the walls and floors wherever requiredEtc complete.Queo - (Zelos Neo+CC Sisma)/ KOHLER ESCALE K16817IN-SS-0, OR Equ. |
| 365 | Fixing, Commissioning at site Urinal Partition with fCurved shaped frosted glass fixing with brass screws,nuts , and washers complete including cutting and making good the walls and floors wherever requiredEtc complete. 900x450x10 mm tk. Make: Jaquar 1110uc/ equ. |
| 366 | Fixing, Commissioning at site Glass Shower Partition with glass fixing, chrome edged fixwith brass screws,nuts , and washers complete including cutting and making good the walls and floors wherever requiredEtc complete. 1950x3000x10 mm tk. Make: Jaquar JSE _CHR_186T3034H19X/ equ. Sze to be confirm as required. |
| 367 | Fixing, Testing and Commissioning at site Wash Basin with basin mixture and accessories Flexible Connection tube, 32 mm C.P. brass waste coupling of standard pattern, and union including cutting and making good the walls wherever required complete.Queo - (FEDRA +F Elegant)/ KOHLER K5373IN-0, OR Equ. (Inside Toilets) |
| 368 | Fixing, Testing and Commissioning at site Wash Basin with basin mixture and accessories Flexible Connection tube, 32 mm C.P. brass waste coupling of standard pattern, and union including cutting and making good the walls wherever required complete. For dining area.Queo - (FELISA +F M Mosaico)/ KOHLER K73159IN-7-RGD, OR Equ.( Comman Area) |
| 369 | Fixing, Testing and Commissioning at site ablution Health Spray Faucet with wall hook and 1.2 mtr. Chrome plated PVC hose pipe, etc. complete in all respects. Queo - Addons/Kohler/Grohe |
| 370 | Fixing, testing and commissioning of Single Lever Diverter with provision for spout and over head shower with shower arm, shower rose, wall flange and spout, all accessories etc, complete. Queo - (Aquaplan +F Elegant)/ KOHLER K-14795IN-CP/Grohe Metropole, OR Equ. |
| 371 | Fixing, testing and commissioning of Single Lever Diverter with provision for spout and over head shower with shower arm, shower rose, wall flange and spout, all accessories etc, comple Fixing CP Robe hook Queo - Q363196120/ KOHLER K-97499T-CP/Grohe 41711, OR Equ. |
| 372 | Providingandfixingofbathingaccessoriessetofonepairofsoapdish holder,one no. tumbler holder,one no.napkin ring,one no.600mm glass shelf with all required fittings and accessories. |
| 373 | Supplying,Fixing, Testing, and commissioningSink Mixerwall mounted/floor mounted with swivel casted spout and wall flange, trending cutting and making good the walls whatever required etc. complete Queo - Allamoda/Kohler/Grohe |
| 374 | Supplying, Fixing, testing and commissioning at site Stainless Steel Sink with drain board and doublebowl, depth 200mm manufactured from 1mm thick stainless steel, 18G high grade indestructible chrome nickel steel with top quality polish, 40mm dia full threaded CP waste coupling, with all accessories etc complete. Nirali Greaceful elagance/ Diamond super delux |
| 375 | B. SOIL, WASTE, VENT & RAIN WATER PIPES |
| 376 | Supplying, Fixing, testing and commissioning at site in positionuPVC pipe -6kg/cm2) (IS:4985)Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, door bends, junctions, cowls, etc.,complete. (Soil & Waste in Shaft) Make: Astral/Supreme/Ajay INSHAFT 110 mm O.D. (6Kgf/cm2 IS:4985) |
| 377 | Supplying, Fixing, testing and commissioning at site in positionuPVC pipe -6kg/cm2) (IS:4985)Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, door bends, junctions, cowls, etc.,complete. (Soil & Waste in Shaft) Make: Astral/Supreme/Ajay INSHAFT 75 mm O.D.(6Kgf/cm2 IS:4985) |
| 378 | Supplying, Fixing, testing and commissioning at site in positionuPVC pipe -6kg/cm2) (IS:4985)Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, door bends, junctions, cowls, etc.,complete. (Soil & Waste in Shaft) Make: Astral/Supreme/Ajay INSHAFT 63 mm O.D( 4Kgf/cm2) Vent pipe in shaft |
| 379 | Providing, Fixing, testing and commissioning at site in position uPVC pipe( IS : 4985 ) With Rubber Ring or Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, etc. complete. (For Rain water pipes in shaft & Ceiling) Make: Astral/Supreme/Ajay INSHAFT ( PASTING ONLY) 110 mm O.D( 4Kgf/cm2)) Rain water pipe in shaft |
| 380 | Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends, coupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay(For Internal Soil &Waste line) (PASTEDONLY) 40 mm O.D. (6Kgf/cm2 IS:4985) |
| 381 | Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends, coupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay(For Internal Soil &Waste line) (PASTEDONLY) 50 mm O.D. (6Kgf/cm2 (IS:4985) |
| 382 | Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends, coupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay(For Internal Soil &Waste line) (PASTEDONLY) 75 mm O.D. (6Kgf/cm2 (IS:4985) |
| 383 | Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends, coupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay(For Internal Soil &Waste line) (PASTEDONLY) 110mm O.D (6Kgf/cm2 (IS:4985) |
| 384 | Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends, coupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay(For Internal Soil &Waste line) (PASTEDONLY) 32 mm O.D. (8Kgf/cm2 (IS:4985) for sunken spout |
| 385 | Supplying, Fixing, testing and commissioning at site in position Deep Seal UPvc fabricated Multi floor trap (7”), with suitable supporting on GI slotted rails (1.6mmthick) full threaded rod, anchor fasteners etc. complete in all respects. 50/75 mm dia outlet (In Ceiling)Astral/Supreme/Ajay |
| 386 | Supplying,Fixing, testing and commissioning at site in position UPvc fabricated Multi floor trap (4”),with 50/75 mm dia outlet (In Sunken slab & floor raising areas)Astral/Supreme/Ajay |
| 387 | Supplying,Fixing, Testing and commissioning at site in position 150x150mm square C.P cast brass or stainless steel anti cockroach grating cover ss (304) of matching size of UPvc fabricated floor trap / multi inlet trap complete in all respects Chilly/Eligna/ |
| 388 | Supplying,Fixing, Testing and commissioning at site in positionstainless steel square frames (150x150) ss304 POP UP GRATINGS (for Washing machine)Fixing, complete in all respects Chilly/Eligna/ |
| 389 | Supplying,Fixing, testing and commissioning at site in position Concealed floor trap (4” UPvc fabricated Multi Trap, with Stainless Steel Square frames (150x150mm) SS (304), Rubber Seal and flat round cover with screw. etc. complete in all respects. Chilly/Eligna/ |
| 390 | Supplying,Fixing, testing at site in position 160mm dia square /circular grating Terrace rain water outlet(Cast Iron)(for 110mm dia pipe) |
| 391 | Supplying, Fixing, testing at site in position PVC Roding Eye (6kg/cm2) Complete in all respects. 110 mm dia |
| 392 | Supplying, Fixing, testing at site in position PVC Roding Eye (6kg/cm2) Complete in all respects. 75 mm dia |
| 393 | Supplying,Fixing, testing and commissioning at site in position SS Floor cleanoutwith Stainless Steel Square frames (150x150mm) SS (304), Rubber Seal and flat round cover with screw. etc. complete in all respects. 110 mm dia |
| 394 | C. WATER SUPPLY (INTERNAL AND EXTERNAL) |
| 395 | Supplying, Fixing, testing and commissioning at site Puddle Flangefabricated from Upvc ASTM Grade sch-40 pipes & uPVC sheet (600 mm long) 2 ” (50mm) dia |
| 396 | D.EXTERNAL SEWERAGE |
| 397 | Supplying and Laying of pipes and conveying to position; cleaning, laying and jointing to true lines and gradients,with proper bedding uPVC pipe of IS 4985(6kgf/cm2)including jointing the pipe as per specification, testing the pipe line after installation all per provisions of IS: 1742-1983 (Code of practice for building drainage) complete as directed by the Employer 75mm OD (6/kg/cm2) |
| 398 | Supplying and Laying of pipes and conveying to position; cleaning, laying and jointing to true lines and gradients,with proper bedding uPVC pipe of IS 4985(6kgf/cm2)including jointing the pipe as per specification, testing the pipe line after installation all per provisions of IS: 1742-1983 (Code of practice for building drainage) complete as directed by the Employer 110mm OD (6/kg/cm2) |
| 399 | Supplying and Laying of pipes and conveying to position; cleaning, laying and jointing to true lines and gradients,with proper bedding uPVC pipe of IS 4985(6kgf/cm2)including jointing the pipe as per specification, testing the pipe line after installation all per provisions of IS: 1742-1983 (Code of practice for building drainage) complete as directed by the Employer 160mm OD (6/kg/cm2) |
| 400 | E.PUMP AND ACCESSORIES |
| 401 | Supply,Installation, Testing and commissioning of Clear water transfer pump of adiquate hp with discharge 2 lps at 20 mtr head, SS body, ss shaft with bronze impeller mounted on a single base platewith controll panel and auto level controller. 1 working+ 1 stand by |
| 402 | Supply,Installation, Testing and commissioning of Clear water transfer pump of adiquate hp with discharge 2 lps at 20 mtr head, SS body, ss shaft with bronze impeller mounted on a single base platewith controll panel and auto level controller. 1 working |
| 403 | TERRACE DWS BOOSTER PUMP Duty Conditions of 6 lps @ 35 mtr - head(Each pump3LPS 35 mtr Head - 2 Pump system-1 Working+1standby) Compact skid mounted Booster pumps with SS 304 casing, SS316 impeller , SS316 shaft , C I base and TEFC motorwith mechanicalseal. Pumpto be havesingle VFD logic controller. - Electriccontrol panel withlogic controller, relays, calibrated pressure switch, pressuretransmitter including cabling within panel, incorporating dry run protection, potential contacts forBMS integrating , sucton and discharge headers, pressure vessal 60 ltr capacity. |
| 404 | Supply, installation, testing and commissioning of 600 LPD Solar Water Heater with Control panel with necessary controls, and other standard accessories as instructed by S-I-C. |
| 405 | Supply, installation, testing and commissioning of 200 LPD Solar Water Heater with Control panel with necessary controls, and other standard accessories as instructed by S-I-C. |
| 406 | Incinerators with capacity of 50 kG per day include air pollution control equipment (e.g., fabric filters, scrubbers, electrostatic precipitators) to remove fly ash and gaseous contaminants |
| 407 | Providing,fixing,jointingandtesting,heavyquality caststeel /Brassball valve with plastic float, 40 mm dia single/double piece designed ofapproved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter. Make:ZOLOTO/VTC/SANT |
| 408 | Supply, installation, testing and commissioning of percolation well (Recharge well) including all work like drilling, compressor work, gravel packing, mud slurry disposal, clay packing and including of all materials like 300mm UPVC pipe, 300mm wire screens, 300mm collar joint, accessories, gravels, sand, sand filteration module etc. Site cleaning, mud pit, mud refilling for borewell must be in the contractor"sscope.Contractorhastomaintainthepercolationwellupto three years after installation. |
| 409 | Providing erecting and fixing double coated SIntex or equivalent PVC. (ISI) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace. (Make: Sintex / Kaka ) |
| 410 | Supply, installation, testing and commissioning of Swimmng pool filtration system comprising of Bobbin wound Sand filter 450 mm dia with side mount 6 Way Multiport Valve, Filter Media (Silica Sand) 25Kg. Bags, Filtration Pump with Prefilter, Wall inlet fitting in ABS, 2" Connection, Vacuum Point in White ABS with, 50mm Connection, Anti Vortex Drain in white ABS BL 311, Skimmer in white ABS SL-111M, Warm White LED Under-Water Light without Niche, LED Driver Protection Box, Universal Deck Box in White ABS, 63mm PVC Double Union Valve, 50mm PVC 3 piece Union adaptor, Concrete Metal Vacuum Head, Floating Hose 6 mtrs, Telescopic Pole 2.4 to 4.8mtr in 2 parts, Luxury Deep leaf rake made in polypropelene and aluminium frame, Luxury Surface hand skimmer with aluminium frame, Curved brushes made in polypropelene and with aluminium reinforcement 45 cms for for pool basins, Test kit for chlorine & pH, Control panel for pumps with necessary controls, and other standard accessories as instructed by S-I-C. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
