MAHARANA PRATAP HORTICULTURE UNIVERSITY has published Tender For Construction Of Administrative Block And Other Allied Structures At Regional Research Station, Raiya (Jhajjar) Of Mhu, Karnal. Submission Date for this Tender is 07-12-2022. Building Work Tenders in jhajjar Haryana. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 01-Dec-2022 | Corrigendum | Other | 07-12-2022 |
| Sl. No. | Item Description |
| 1 | Description and details |
| 2 | HSRITEMNO.4.14. Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 4.14.1 All kinds of soil |
| 3 | HSRITEMNO.4.32 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 4 | HSRITEMNO.4.39 Providing and injecting chemical emulsion for PRE- CONSTRUCTIONAL anti termite treatment and creating a chemical barrier under and around the column pits, walltrenches, basement excavation, top surface of plinth filing junction of wall and floor, along with the external perimetre of building, expansion joints surrounding of pipes and conduit etc, complete (plinth area of the building at ground floor only shall be measured) using Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 5 | HSRITEMNO.6.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level. 6.1.61 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) |
| 6 | HSRITEMNO.6.8 Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) 6.8.2 40mm |
| 7 | HSRITEMNO.6.10 Providing & applying a coat of residual petroleum bitumen of sqm grade of VG-1 O of approved quality using 1. 7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 8 | HSRITEMNO.6.13 Making plinth protection 50mm thick of cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth |
| 9 | HSRITEMNO.6.14 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: 6.14.1 1:1.5:3 ( 1 cement : 1. 5 coarse sand (zone-Ill): graded stone aggregate 20 mm nominal size) |
| 10 | HSRITEMNO.6.14 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: HSRITEMNO.6.14.2 1 :2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded cum stone aggregate 20 mm nominal size) |
| 11 | HSRITEMNO.6.15 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 6.15.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 cum graded stone aggregate 20 mm nominal size) |
| 12 | HSRITEMNO.6.16 Reinforced cement concrete work in beams, suspended floors, cum roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). |
| 13 | HSRITEMNO.6.30 Centering and shuttering including strutting, propping etc. and removal of form for 6.30.1 Foundations, footings, bases of columns, etc. for mass concrete |
| 14 | HSRITEMNO.6.30.3 Suspended floors, roofs, landings, balconies and |
| 15 | HSRITEMNO.6.30.5 Lintels, beams, plinth beams, girders, bressumers and cantilever |
| 16 | HSRITEMNO.6.30.6 Columns, Pillars, Piers, Abutments, Posts and Struts |
| 17 | HSRITEMNO.6.30.7 Stairs, (excluding landings) except spiral-staircases |
| 18 | HSRITEMNO.6.30.15 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 19 | HSRITEMNO.6.30.16.1 Edges of slabs and breaks in floors and walls |
| 20 | HSRITEMNO.6.30.19 Weather shade, Chajja, corbels etc., including sqm edges |
| 21 | HSRITEMNO.6.34 Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 6.34.6 Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 22 | HSRITEMNO.7.21 Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: 7.21.2 Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 23 | HSRITEMNO.7.22 Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 7.22.2 Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 24 | HSRITEMNO.7.28 Half brick masonry with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level. 7.28.2 Cement mortar 1 :4 ( 1 cement :4 coarse sand) |
| 25 | HSRITEMNO.8.26 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.8.26.2.2 Area of slab over 0.50 sqm |
| 26 | HSRITEMNO.8.27 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 8.27.2 Granite work |
| 27 | HSRITEMNO.8.28 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platfonn, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 28 | HSRITEMNO.9.10 Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete 9.10.1With residual type petroleum bitumen of grade VG -10 |
| 29 | HSRITEMNO.9.11 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tilebricks, grouted with cement mortar 1 :3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: 9.11.1 With common burnt clay non- modular brick tile of class sqm designation 10 |
| 30 | HSRITEMNO.9.17 Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design : 9.17.1 In 75x75 mm deep chase |
| 31 | HSRITEMNO.9.18 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 32 | HSRITEMNO.9.47.2 GI Metal Ceiling Lay in perforated Tegular edge global whitecolour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC(Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fibre acoustical fleece |
| 33 | HSRITEMNO.9.57 Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 9.57.2110 mm diameter |
| 34 | HSRITEMNO.9.57Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 9.57.3150 mm diameter |
| 35 | HSRITEMNO.9.58 Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion. 9.58.2Single push fit Coupler 9.58.2.2110 mm |
| 36 | HSRITEMNO.9.58 Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion. 9.58.2Single push fit Coupler 9.58.2.3150 mm |
| 37 | HSRITEMNO.9.58.3Single tee with door 9.58.3.2110x110x110 mm |
| 38 | HSRITEMNO.9.58.3Single tee with door 9.58.3.3150x150x150 mm |
| 39 | HSRITEMNO.9.58 Single tee without door 9.58.4.2 110x110x110 mm |
| 40 | HSRITEMNO.9.58 Single tee without door 9.58.4.3 150x150x150 mm |
| 41 | HSRITEMNO.9.58 Shoe (Plain) 9.58.6.2110 mm Shoe |
| 42 | HSRITEMNO.9.58 Shoe (Plain) 9.58.6.3150 mm Shoe |
| 43 | HSRITEMNO.9.60 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighing not less than 440 grams |
| 44 | HSRITEMNO.9.61Providing and fixing to the inlet mouth of rain water pipe PTMT (anEngineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms. |
| 45 | HSRITEMNO.10.1 Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm sand or stone filling. |
| 46 | HSRITEMNO. 10.3Supplying and providing of Tangri River Sand under floors Including wateringand compaction in 25cm layers, dressing etc. complete In all respects (As per item 10.2) |
| 47 | HSRITEMNO.10.4 Providing and laying of screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping |
| 48 | HSRITEMNO.10.7Providing and laying of conglomerate floor 50mm thick cement concrete topping 1 :2:4 |
| 49 | HSRITEMNO.10.10Providing and laying Cement concrete flooring 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 10.10.1 40 mm thick with 20 mm nominal size stone aggregate |
| 50 | HSRITEMNO.10.14 Providing a floating coat of 1.50 mm thick neat cement laid in one operation to the topping |
| 51 | HSRITEMNO.10.22 Providing and fixing glass strips in joints of terrazzo/ cement concrete floors. 10.22.1 40 mm wide and 4 mm thick |
| 52 | HSRITEMNO.10.30.4 Providing and laying of chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement: 4 coarse sand). 10.30.4Ordinary cement without any pigment |
| 53 | HSRITEMNO.10.31Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. 10.31.1In flooring on a bed of 1 O mm thick mortar 1 :4 ( 1 acid proof cement : 4 coarse sand) 10.31.1.1Acid and alkali resistant tile |
| 54 | HSRITEMNO.10.31Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In dado/skirting on 12 mm thick mortar 1 :4 (1 acid proof cement: 4 coarse sand) 10.31.2.1Acid and alkali resistant tile |
| 55 | HSRITEMNO.10.50.1Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 10.50.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, sqm Cat Eye or equivalent. |
| 56 | HSRITEMNO.10.51Providing and fixing granite stone in all shades 15mm to 18 mm thick in skirting /dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1 :3 and jointed with white cement slurry mixed with pigment to match the shade of Granite including labour for fixing cramps pins and dowels etc. |
| 57 | HSRITEMNO.10.54Providing and fixing 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : 10.54.1 Second class teak wood |
| 58 | HSRITEMNO.10.58Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 59 | HSRITEMNO.10.63Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 10.63.2 Size of Tile 600x600 mm |
| 60 | HSRITEMNO.10.67Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 10.67.2Size of Tile 600x600 mm |
| 61 | HSRITEMNO.10.70Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in- charge. 10.70.2 Size of Tile 600x600 mm |
| 62 | HSRITEMNO.10.98Providing and fixing Grass paver block of required strength and thickness on 25 mm thick compacted bed of sand and filling the joint with sand complete in all respec |
| 63 | HSRITEMNO.10.106 Providing and laying matt finished vitrified tile of size 300x300x9.8mm havingwith water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 64 | HSRITEMNO.10.107Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1 :4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 65 | HSRITEMNO.11.410 mm thick cement plaster 11.4.1 1 :2 (1 cement: 2 fine sand) |
| 66 | HSRITEMNO.11.812 mm cement plaster of mix : 11.8.21 :6 (1 cement: 6 coarse sand) |
| 67 | HSRITEMNO.11.915 mm cement plaster on rough side of single or half brick wall of mix: 11.9.2 1 :6 (1 cement: 6 coarse sand) |
| 68 | HSRITEMNO.11.17 Providing and fixing of chicken wire mesh for avoiding cracks in plaster with necessary nail/screws etc. complete in all respect to the entire satisfaction of engineer-in-charge |
| 69 | HSRITEMNO.11.54 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. Projection. |
| 70 | HSRITEMNO.11.58 Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete |
| 71 | HSRITEMNO.11.67 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: 11.67.1Water thinnable cement primer |
| 72 | HSRITEMNO.11.75 Wall painting with premium acrylic emulsion paint of interior grade, having voe (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 11.75.2 Two coats |
| 73 | HSRITEMNO.11.77Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc. |
| 74 | HSRITEMNO.11.78 Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. |
| 75 | HSRITEMNO.11.82 Painting the wooden/metal surface with synthetic enamel paint of approved brand and manufacture to give an even shade 11.82.1 Two or more coats on new work |
| 76 | HSRITEMNO.11.91Melamine polishing on wood work (one or more coat). |
| 77 | HSRITEMNO.11.94.1 Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 litre/10 sqm) |
| 78 | HSRITEMNO.11.98 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gmnitre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. 11.98.1 New work (Two or more coats applied @ 1.43 litre/ 10 sqm Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm |
| 79 | HSRITEMNO.12.12Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 12.12.21.0 mm thick |
| 80 | HSRITEMNO.12.15Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 81 | HSRITEMNO.12.32 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws. 12.32.1.135 mm thick shutters with ISi marked M.S. pressed butt hinges bright finished of required size 13.32.1.1.1 Second class teak wood |
| 82 | HSRITEMNO.12.33Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complet. 12.33.2 With 12 mm mild steel U beading |
| 83 | HSRITEMNO.12.36Providing and fixing ISi marked flush door shutters conforming to IS : 2202(Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 12.36.1 35 mm thick including ISi marked Stainless Steel butt hinges with sqm necessary screws |
| 84 | HSRITEMNO.12.40.1 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or squar |
| 85 | HSRITEMNO.12.49 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets: 12.49.2 25 mm dia (heavy type) |
| 86 | HSRITEMNO.12.50 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. HSRITEMNO.12.50.2 Fixed to openings /Wooden frames with rawl plugs screws etc. |
| 87 | HSRITEMNO.12.87Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe shutters, including fixing with necessary screws etc. complete. 12.87.1Triple strip vertical type |
| 88 | HSRITEMNO.12.89 Providing and fixing aluminium e xtruded section body tubular type universalhydraulic door closer (having brand logo with ISi, IS: 3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1 000 mm), with double speed adjustment with necessary accessories and screws etc. complete |
| 89 | HSRITEMNO.12.98 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 12.98.1 300x16 mm |
| 90 | HSRITEMNO.12.99Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. 12.99.2 250x10 mm |
| 91 | HSRITEMNO.12.99.4 150x 10 mm |
| 92 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed torequired colour or shade, with necessary screws etc. complete. 12.102.1 125 mm |
| 93 | HSRITEMNO.12.102.2Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed torequired colour or shade, with necessary screws etc. complete. 12.102.2 100 mm |
| 94 | HSRITEMNO.12.103 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 12.103.2 Twin rubber stopper |
| 95 | HSRITEMNO.12.118.2 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter sqm made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (:t 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the comers by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (:t 0.1mm) wall thickness. The lock rail made up of "H" section, a uPVC hollow section of size 100x30 mm and 2 mm (:t 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. "U" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (:t 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer"s specification and direction of Engineer-in-charge. |
| 96 | HSRITEMNO.12.119Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a metre wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at comers and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer"s specification and direction of Engineer- in- Charge |
| 97 | HSRITEMNO.12.132 Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 :t 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all comers, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. 12.132.1Fixed window/ ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 :t 0.2 mm and single glazing bead of appropriate dimension. (Area up to 0.75 sqm) |
| 98 | HSRITEMNO.12.134 Providing and fixing factory made uPVC white colour sliding glazed window up to 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x B mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all completeas per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made 12.134.2Three track three panels sliding window with fly proof SS wiremesh (Two Nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window up to 1.75 sqm |
| 99 | 12.134.4 Three track three panels sliding window with fly proof S.S wiremesh (Two Nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). |
| 100 | HSRITEMNO.12.137Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge. 12.137.1 200 x 19 x 1.9 mm |
| 101 | HSRITEMNO. 12.138 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete. |
| 102 | HSRITEMNO. 12.139Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete. |
| 103 | HSRITEMNO. 12.140Providing and fixing steel roller for uPVC sliding window with necessaryscrews etc. complete. |
| 104 | HSRITEMNO. 12.141Providing and fixing steel roller for uPVC sliding door with necessary screwsetc. complete |
| 105 | HSRITEMNO. 12.142Providing and fixing steel (white power coated) crescent lock for uPVC slidingwindow/ door with necessary screws etc. complete. |
| 106 | HSRITEMNO.12.157 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- charge. (Glazing, panelling and dash fasteners to be paid for separately) : 12.157.1 For fixed portion12.157.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 107 | HSRITEMNO.12.157.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 12.157.2.2Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 108 | HSRITEMNO.12.158 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 12.158.2Pre-laminated particle board with decorative lamination on both sides |
| 109 | HSRITEMNO.12.159 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 12.159.2 With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg/sqm) |
| 110 | HSRITEMNO.12.160 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. 12.160.1With stainless steel cover plate minimum 1.25 mm thickness |
| 111 | HSRITEMNO.12.177 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as perthe architectural drawings and the directions of engineer-in-charge . 12.177.1 With toughened glass panes of 6 mm thickness (weight not less than 15 kg/sqm) |
| 112 | HSRITEMNO.13.3 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: 13.3.2 Profile C 13.3.2.1 Fixing with adjustable lugs with split end tail to jamb |
| 113 | HSRITEMNO.13.3.2.2 Fixing with carbon steel galvanised dash fastener metreof required dia and size (to be paid for separately) |
| 114 | HSRITEMNO.13.3.3 Profile E 13.3.3.1 Fixing with adjustable lugs with split end tail to each jamb |
| 115 | HSRITEMNO.13.3.3.2 Fixing with carbon steel galvanised dash fastenerof required dia and size (to be paid for separately) |
| 116 | HSRITEMNO.13.4.1Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of requiredsize, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) |
| 117 | HSRITEMNO. 13.10 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 13.10.25.5 mm thick glass panes |
| 118 | HSRITEMNO.13.29.2Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 119 | HSRITEMNO.13.34 Supply and Fixing of Tensile Sheet Shed 650GSM sheet with M.S Iron pipe Frame Pole 125mm Heavy Truss M.S Pipe 60mm Heavy, Membrane M.S Pipe 50mm Heavy, Complete With cost of Painting and Labour for Fixing Paint Complete in all respects |
| 120 | HSRITEMNO.13.35 Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and comers, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer |
| 121 | HSRITEMNO.13.41 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainlesssteel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 122 | HSRITEMNO.13.44 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling each 30 118 148 fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 123 | HSRITEMNO.17.5 Compacting Original Ground 17.5.3 Compaction of EarthworkCompaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (in case of link roads earthwork to be done by villagers) |
| 124 | HSRITEMNO.17.13 Granular Sub-Base (Mix in place) Construction of granular sub-base by providing Material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with Rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per technical clause 401 of MORT&H technical specifications |
| 125 | HSRITEMNO.17.22Water Bound Macadam Gr I 17.22.1 Water Bound Macadam Grading screenings for low volume (undesignated) (without roads Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical clause 404 of MORT&H specifications. |
| 126 | HSRITEMNO.17.23 Water Bound Macadam Grading -II 17.23.2 Water Bound Macadam - II with Screening Type "A" / Type B Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-1 0 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical clause 404 of MORT&H specifications |
| 127 | HSRITEMNO.17.69 Interlocking Concrete Block Pavement 17.69.2Providing and Laying 80 mm thick ISi marked lntertocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect |
| 128 | HSRITEMNO.21.95Providing lowering cutting jointing and testing RCC pipe class NP 3 as per 18-458-2003 with spigot & socketed joints manufactured with ISi marked sulphate resistance cement as per ISi 12330 with rubber rings ISi marked antiternmite as required at site in to trenches for all depths and laying out the same to correct alignment gradients and levels including dressing and trimming and cutting of concrete beds and side of trenches, if required jointing with rubber rings in trenches and jointing with 1 :3/2 cement sand mortar and with end dowels filled with 1 :3/2. cement sand mortar and finishing the joints at an angle of 45 degree with faces of spigot of socket joints cutting and finishing the cut surface to a uniform finish etc. as fully described in item No . 21.38, item 21.44, item 21.45, & item 21.46 including cartage loading and unloading complete in all respects. the internal diametric of the sewer being: 21.95.3450mm |
| 129 | HSRITEMNO.29.1 Providing and supplying aluminium extruded tubular and other aluminium kg 360 360 sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to MMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. |
| 130 | HSRITEMNO.29.2 Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.29.6) For payment, only the actual area of glass on face# 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating sqm 271 2271 2541 on face # 2, + 12mm Air gap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VL n of 25 to 35 %, Light reflection internal 1 O to 15%, light reflection external 1 O to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. |
| 131 | HSRITEMNO.29.3 Extra for openable side / top hung vision glass panels (IGUs) includingproviding and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge. |
| 132 | HSRITEMNO.29.4 Providing, fabricating and supplying shadow box of required size and shape,x for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi -rigid, inorganic, noncombustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminium sheet backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete. |
| 133 | HSRITEMNO.30.82 Making holes by cutting cores of appropriate dia in RCC floors and roofs of thickness up to 6" (six inches) for passing drain pipe and repairing the hole after insertion of drain pipe etc. including finishing-complete so as to make it leak proof. 30.82.1 Drain pipe of 150mm internal dia |
| 134 | HSRITEMNO.30.82.2 Drain pipe of 100mm internal dia |
| 135 | HSRITEMNO.33.6 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, up to 90 metre depth below ground level. 33.6.1All types of soil 33.6.1.1300 mm dia |
| 136 | HSRITEMNO.33.8 Supplying, assembling, lowering and fixing in vertical position in bore well, Unplasticised PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 33.8.3200 mm nominal size dia |
| 137 | HSRITEMNO.33.9 Supplying, assembling, lowering and fixing in vertical position in bore well Unplasticised PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 33.9.3 200 mm nominal size dia |
| 138 | HSRITEMNO.33.12 Supplying, filling, spreading & levelling stone boulders of sizerange 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge |
| 139 | HSRITEMNO.33.13Supplying, filling, spreading & levelling gravels of size range 5 cum mm to 1 O mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 140 | HSRITEMNO.33.14 Supplying, filling, spreading & levelling coarse sand of size range cum 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. |
| 141 | HSRITEMNO.33.15 Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 142 | HSRITEMNO.33.19 Development of tube well in accordance with IS : 2800 (part I)and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V"" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 143 | NS:- Extra for using Double chrged vitrifiedTiles of approved design & make having size 600*600 mm implace of single chargedVitrified Tiles. Make DaCIA Green of Somany or equivalent. |
| 144 | NS:-Providing and fixing re-inforced concrete screen (Approx size 1200mm x 800mm) 25 mm thick casted with power spray concrete mix design in Dholpur Shade without border (Acid wash stone finished) having density1.8-2 gram/sq. cm., compressive strength 35-55 MPa, Tensile Strength 4-7 MPa, Impact Strength 7-15 kg./sqm, Fibre content % by weight 2.5-3.5 on premix basis,on existing iron framed with screws, adhesive etc. fixing in position complete in all respect as per satisfaction of Engineer-in-Charge. |
| 145 | NSProviding & Fixing aluminium fittings for door and windows shutters with stainless steel or C.P brass screws of required size complete.FoldingHandle 100mm |
| 146 | NSProviding and fixing Toilet Cubicle (of following standard dimension which includes 600 mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant 12 mm thick solid compact laminate panelsFinish of the compact laminate should be raw silk which include doors, pilasters and intermediate panels finished with approved texture/shade as per the detail drawing and as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless Steel (Grade 316) as per manufacturer"s specifications and EIC instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U- Channels, (6) SS-Shoe Box Plate, (7) MS-Base Plate, (8) Rubber noise deafening tape, (9) Screws and wall Plugs. |
| 147 | PUBLIC HEALTH HSRITEMNO. 4.16 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: 4.16.2 Pipes, cables etc. exceeding 80 mm metre dia. but not exceeding 300 mm dia. |
| 148 | HSRITEMNO. 6.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: . 6.1.21:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm nominal size) |
| 149 | HSRITEMNO. 6.1.7 1:5:10 (1 cement : 5 coarse sand (zone-Ill): 10 graded stone aggregate 40 mm nominal size) |
| 150 | HSRITEMNO. 6.16 Reinforced cement concrete work in beams, suspended floors, cum roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing andreinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). |
| 151 | HSRITEMNO. 6.33.6 Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level: Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.Thermo-Mechanically Treated bars of grade Fe-500D kg or more. |
| 152 | HSRITEMNO. 7.21.1 Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 153 | HSRITEMNO. 10.14 Providing a floating coat of 1.50 mm thick neat cement laid in one operation to the topping. |
| 154 | HSRITEMNO. 11.1.1 6 mm cement plaster of mix: 1 :3 (1 cement : 3 fine sand) |
| 155 | HSRITEMNO. 11.5.1 12 mm cement plaster of mix : 1 :2 (1 cement: 2 fine sand) |
| 156 | HSRITEMNO. 11.52 Cement rendering on plaster 1 mm thick |
| 157 | HSRITEMNO. 11.107 Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work 11.107.3 25 mm diameter pipe |
| 158 | HSRITEMNO. 11.107.5 40 mm diameter pipe |
| 159 | Cutting holes up to 23 cm square through brick work in mud walls for pipes and making good induding repointing, replastering and finishing according to existing finish where required. HSRITEMNO. 20.25.1 11.43 cm thick wall |
| 160 | HSRITEMNO. 20.25.2 22.86 cm thick wall |
| 161 | HSRITEMNO. 20.72 Supplying, errection, testing of Exhaust fan (as per IS code 374) having a each capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge. |
| 162 | HSRITEMNO. 21.28 Providing & fixing steel bar embedded plastic steps of size 263mm x 165mm of orange colour, confirming to specification in pump chambers, manholes etc., having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS : 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1 :2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in-charge |
| 163 | HSRITEMNO. 21.57 Providing masonry plugs to ends of sewers of all types with 11.43 cm thick brick wall in cement sand mortar 1 :7 with 12 mm thick cement plaster 1: 6 (as required by the engineer-in-charge). HSRITEMNO. 21.57.1.2150 mm |
| 164 | HSRITEMNO. 21.84 Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1 :2:4 benching 12mm thick cement plaster 1 :2 with a floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty C.I. inspection chamber cover and frame weight as per 1.5.1. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. HSRITEMNO. 21.84.1 Size 450 mm X450 mm inside (with 455 mm x 455 mm coverand frame light duty single seal weighing 20 kg with C.C. topping |
| 165 | HSRITEMNO. 21.84.2 Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern I weighing 38 kg with C.C. topping) |
| 166 | HSRITEMNO. 21.85 Extra for every 0.30 metre depth of Inspection chamber 21.85.1 450 mm x 450 mm inside |
| 167 | HSRITEMNO. 21.85.2 450 mmx 600 mm inside |
| 168 | HSRITEMNO. 21.93 Providing and fixing SFRC MANHOLE COVERS AND FRAMES MARKED WITH IS: 12592 including setting the same to correct lines and levels in 1 :3 cement sand mortar over manhole including carriage loading unloading stacking handling re-handling etc. complete in all respects to the satisfaction to the Engineer-in-charge. 21.93.2Type:- Extra Heavy Duty Set (EHD-20) 560MM Clear Opening |
| 169 | HSRITEMNO. 22.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 22.1.4 White vitreous chinaware Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 170 | HSRITEMNO. 22.5 Providing and fixing white vitreous chinaware pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 171 | HSRITEMNO. 22.6.2 Providing and fixing white vitreous chinaware laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required: Size 600x450x200 mm |
| 172 | HSRITEMNO. 22.8 Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge). 22.8.1 One way |
| 173 | HSRITEMNO. 22.10 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 22.10.1.3 510x1040 mm bowl depth 200 mm |
| 174 | HSRITEMNO. 22.14 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 22.14.1 Semi rigid pipe 22.14.1.132 mm dia |
| 175 | HSRITEMNO. 22.15 Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & each 18 805 823 make and as per the direction of Engineer-in-charge. |
| 176 | HSRITEMNO. 22.20Providing and fixing in position C.I. plain Nahani Trap conforming to I.S.I. specifications and of self cleaning design with C.P. brass hinged grating with frame complete 22.20.2 With 75 mm internal diameter outlet |
| 177 | HSRITEMNO. 22.22 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 22.22.1 White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 178 | HSRITEMNO. 22.26 Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required 22.26.3Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern |
| 179 | HSRITEMNO. 22.26.4 Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern |
| 180 | HSRITEMNO. 22.33 Providing and fixing white vitreous chinaware extended wall mounting watercloset of size 780x370x690 mm of approved shape including providing & fixing white vitreous chinaware cistern / PVC cistern (with brass fitting) into the wall with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 181 | HSRITEMNO. 22.34 Providing and fixing floor mounted, white vitreous chinaware single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous chinaware cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 182 | HSRITEMNO. 22.38 Providing and fixing 8 mm dia C.P. I S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. |
| 183 | HSRITEMNO. 22.42 Providing and fixing toilet paper holder C.P. brass (HSR 22.42.1) |
| 184 | HSRITEMNO. 22.49.1 Providing and fixing in position best Indian make Whitevitreous chinaware channel of size 600mmx150mm including laying and fixing in cement concrete 1 :2:4 complete as required by the Engineer-in-charge. |
| 185 | HSRITEMNO. 22.53 Providing and fixing M.S. holder-bat clamps of approved design to Sand Castiron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 22.53.1For 100 mm dia pipe |
| 186 | HSRITEMNO. 22.53.2 For 75 mm dia pipe |
| 187 | HSRITEMNO. 22.80 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 22.80.2.1 Sand cast iron S&S as per IS - 3989 |
| 188 | HSRITEMNO. 22.85 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge 22.85.325 mm nominal outer dia Pipes |
| 189 | HSRITEMNO. 22.85.4 32 mm nominal outer dia Pipes |
| 190 | HSRITEMNO. 22.86 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good 22.86.1 15 mm nominal outer dia Pipes |
| 191 | HSRITEMNO. 22.86.2 20 mm nominal outer dia Pipes |
| 192 | HSRITEMNO. 22.86.3 25 mm nominal outer dia Pipes |
| 193 | HSRITEMNO. 22.86.4 32 mm nominal outer dia Pipes |
| 194 | HSRITEMNO. 22.87.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 22.87.540 mm nominal outer dia Pipes |
| 195 | HSRITEMNO. 22.87.6 50 mm nominal outer dia Pipes |
| 196 | HSRITEMNO. 22.87.8 75 mm nominal inner dia Pipes |
| 197 | HSRITEMNO. 22.87.9 100 mm nominal inner dia Pipes |
| 198 | HSRITEMNO. 22.87.10 150 mm nominal inner dia Pipes |
| 199 | HSRITEMNO. 22.88 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work· Exposed on wall 22.88.325 mm dia nominal bore |
| 200 | HSRITEMNO. 22.88.5 40 mm dia nominal bore |
| 201 | HSRITEMNO. 22.89 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 22.89.1 15 mm dia nominal bore |
| 202 | HSRITEMNO. 22.89.2 20 mm dia nominal bore |
| 203 | HSRITEMNO. 22.91 Providing and fixing G.I. pipes complete with G.I. fittings including trenching up to 0.30m to 1.00m depth and refilling etc. 22.91.6 50 mm dia nominal bore |
| 204 | HSRITEMNO. 22.93 Providing and filling sand envelope of grading zone grade, 100mm all-round the G.I. pipes in external work: (22.93.6) 50mm diameter pipe |
| 205 | HSRITEMNO. 22.94 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 22.94.1 15 mm nominal bore |
| 206 | HSRITEMNO. 22.94.2 20 mm nominal bore |
| 207 | HSRITEMNO. 22.94.3 25 mm nominal bore |
| 208 | HSRITEMNO. 22.94.5 40 mm nominal bore |
| 209 | HSRITEMNO. 22.94.6 50 mm nominal bore |
| 210 | HSRITEMNO. 22.98 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 22.98.2 20 mm nominal bore |
| 211 | HSRITEMNO. 22.98.1 25 mm nominal bore |
| 212 | HSRITEMNO. 22.98.4 40 mm nominal bore |
| 213 | HSRITEMNO. 22.98.5 50 mm nominal bore |
| 214 | HSRITEMNO. 22.103 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 22.103.325 mm nominal bore |
| 215 | HSRITEMNO. 22.104 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 22.104.1 15 mm nominal bore |
| 216 | HSRITEMNO. 22.105.1 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore |
| 217 | HSRITEMNO. 22.106 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15 mm nominal bore (HSR 22.106.1) |
| 218 | HSRITEMNO. 22.107. Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (HSR 22.107.1) |
| 219 | HSRITEMNO. 22.108 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore (HSR 22.108.1) |
| 220 | HSRITEMNO. 22.109 Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 221 | HSRITEMNO. 22.117 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 222 | HSRITEMNO. 22.119 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 22.119.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 223 | HSRITEMNO. 22.123 Providing and fixing PTMT grating of approved quality and colour. 22.123.1 Circular type 22.132.1.1 100 mm nominal dia |
| 224 | HSRITEMNO. 22.127 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 225 | HSRITEMNO. 22.128.1 Providing and fixing Unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.: 15 mm nominal bore with 30cm length |
| 226 | HSRITEMNO. 22.128.2 15 mm nominal bore with 45 cm length |
| 227 | HSRITEMNO. 22.163 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1: 1 (1 cement : 1 fine sand) including testing of joints etc. complete: 22.163.1 100 mm diameter |
| 228 | HSRITEMNO. 22.163.2 150 mm diameter |
| 229 | HSRITEMNO. 22.163.3 200 mm diameter |
| 230 | HSRITEMNO. 22.164 Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design. 22.164.1 100 mm diameter S.W. pipe |
| 231 | HSRITEMNO. 22.164.2 150 mm diameter S.W. pipe |
| 232 | HSRITEMNO. 22.164.3 200 mm diameter S.W. pipe |
| 233 | HSRITEMNO. 22.166 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: ( HSR 22.166.2) 150 x100 mmsize Ptype (HSR 22.166.2.1)With common burnt claynon- modular bricks of class designation 10.5 |
| 234 | HSRITEMNO. 22.181 Providing and placing on terrace (at all floor levels) polyethylene water litre 7 8 storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 235 | HSRITEMNO. 22.209 Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 236 | HSRITEMNO. 22.212 Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P. brass screws and rawl plugs etc. complete including cutting and making good the walls etc. (HSR 22.212.1.1) One Way |
| 237 | Providing and fixing in position best Indian make (to the approval of the engineer-in-charge) storage type automatic electric water heater, pressure/non-pressure type thermostatically controlled, suitable for operation on 230 volts, 50 cycles single phase vertical wall mounting fitted with-draw able and adjustable type AC, thermostat. Thermostat knob to be readily accessible through the opening of suitable cover for and adjustment of temperature in the installed position of heater and the thermostat should be withdrawn without having to drain the water, electric heating element made out of copper tube (heating element should be easily removed and replaced in the installed position of heater) A neon indicator 1 AMP, inner container made out of copper tinned both from inside and outside, outer container made out of mild steel sheet finished in gleaming white stove enamel paint, insulated between the inner and outer with fibre glass wool with 1 metre length of suitable capacity 3 core flexible cord with plug and non return valve plastic/lead connections or pressure release valve (where required). Complete including fixing and testing for a week (as required by Engineer-incharge. HSR 22.216.125 Litres capacity |
| 238 | Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) including Rack Bolt Screw Pair 115mm long without CP fittings complete in all respect. HSR 22.221.9 Size 560mm x 450mm (Under counter oval) |
| 239 | HSRITEMNO. 22.222 Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing.Single Socket Type B (HSR 22.222.2) 22.222.2 110mm old SWR UPVC pipe lines laid complete |
| 240 | HSRITEMNO. 22.222.2.4 75 mm, Soil & Waste Pipe |
| 241 | SUB-HEAD - 1 : INTERNAL WIRING HSR ITEM NO:- 23.4COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUITS 23.4.1 Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe 23.4.1.3Group C |
| 242 | HSR ITEM NO:- 23.4.2 Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. 23.4.2.3Group C |
| 243 | HSR ITEM NO:- 23.4.3 Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch 23.4.3.3Group C |
| 244 | HSR ITEM NO:- 23.4.4Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required 23.4.4.3Group C |
| 245 | HSR ITEM NO:- 23.4.5Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required 23.4.5.3Group C |
| 246 | HSR ITEM NO:- 23.3.6Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 23.3.6.93 run of Size 1.50 Sqmm(1/1.40mm) |
| 247 | HSR ITEM NO:- 23.3.6.10 3 run of Size 2.50 Sqmm(1.1.80mm) from DB to Switchboards |
| 248 | DSR ITEM NO:- 1.14Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 1.14.104 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 249 | DSR ITEM NO:- 1.14.11 4X 16 sq. mm + 2 X 6 sq. mm earth wire |
| 250 | HSR ITEM NO:- 23.7.6 Supply and erection of PVC CONDUIT ISImarked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. 23.7.6.1PVC pipe of 20 mm dia. |
| 251 | HSR ITEM NO:- 23.7.6.2 PVC pipe of 25 mm dia. |
| 252 | HSR ITEM NO:- 23.7.6.3PVC pipe of 32 mm dia. |
| 253 | HSR ITEM NO:- 23.7.6.4PVC pipe of 40 mm dia. |
| 254 | FITTING AND ACCESSORIES HSR ITEM NO:- 23.8.10 Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 23.8.10.1 1 & 2 Modules including combined plate for Telephone and data |
| 255 | HSR ITEM NO:- 23.8.10.2 3 Modules |
| 256 | HSR ITEM NO:- 23.8.10.46 Modules |
| 257 | HSR ITEM NO:- 23.8.10.58 Modules |
| 258 | HSR ITEM NO:-23.8.11 Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 23.8.11.7step type Fan Regulator 2 modules 300 watt |
| 259 | HSR ITEM NO:-23.8.11.8Telephone Socket outlet modular type |
| 260 | HSR ITEM NO:-23.8.11.11RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type |
| 261 | HSR ITEM NO:-23.8.11.9TV Socket outlet modular type |
| 262 | HSR ITEM NO:-23.8.4Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm each 106 long M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job. |
| 263 | HSR ITEM NO:- 23.23.10 Supplying and drawing of 1 no UTP 4 pair CAT Sa LAN Cable in the existing surface/recess MS/PVC conduit as required |
| 264 | HSR ITEM NO:- 23.22.4 MCCB ,DISTRIBUTION BOARDS, MCB"s, RCCB"s, CHANGE OVER etc. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. 23.22.4.6 TPN DB Horizontal type Double Door 6 way ( 8 incoming 3phase*6 outgoing) |
| 265 | HSR ITEM NO:- 23.22.4.7TPN DB Horizontal type Double Door 8 way ( 8 incoming 3phase*8 outgoing) |
| 266 | HSR ITEM NO:- 23.22.4.8TPN DB Horizontal type Double Door 12 way ( 8 incoming 3phase*12 outgoing) |
| 267 | HSR 23.22.4.9 Supply and erection of double door sheet steel enclosure vertical type distribution board suitable for MCCB as incomer and SP/TP MCB"S as outgoings etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. Vertical TPN DB Double Door 4 way ( 8 incoming 3phase*4outgoing) |
| 268 | HSR ITEM NO:- 23.22.5Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 23.22.5.16 amp. to 32 amp Single Pole |
| 269 | HSR ITEM NO:- 23.22.5.6 40 amp to 63 amp. MCB"s Triple POLE |
| 270 | HSR ITEM NO:- 23.22.5.840 amp to 63 amp. MCB"s FOUR POLE |
| 271 | HSR ITEM NO:- 23.22.6Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessarynnections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. 23.22.6.2DP RCCB 30ma sensitivity , 40 A |
| 272 | HSR ITEM NO:- 23.22.6.3DP RCCB 30ma sensitivity , 63 A |
| 273 | HSR ITEM NO:- 23.22.7Supply and erection of blanking sheet in existing distribution board. |
| 274 | HSR 23.22.1.3 HSR ITEM NO:- 23.22.1 Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work 3 POLE MCCB 16 amp to 100 amp , 25 KA |
| 275 | HSR 23.22.1.4 3 pole MCCB 125 amp to 160 amp , 25 KA |
| 276 | HSR 23.22.1.5 3 pole MCCB 200 amp to 250 amp , 25 KA |
| 277 | HSR 23.22.1.9 4 pole MCCB 6 amp to 100 amp , 25 KA |
| 278 | HSR 23.22.1.10 4 pole MCCB 125 amp to 160 amp , 25 KA |
| 279 | HSR 23.22.1.11 4 pole MCCB 200 amp to 250 amp , 25 KA |
| 280 | HSR 23.22.1.12 4 pole MCCB 300 amp to 400 amp , 25 KA |
| 281 | HSR 23.22.2.1MCCB Enclosure upto 125 Amp. FP |
| 282 | HSR 23.22.2.2 MCCB Enclosure upto 250 Amp. FP |
| 283 | SUB-HEAD - 3 : SUPPLY & ERECTION OF LIGHT AND FAN FIXTURES CEILING FAN/ EXHAUST FAN HSR ITEM NO:- 20.71.1Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge 48" (1200mm) |
| 284 | HSR ITEM NO:- 20.72Supplying, errection, testing of Exhaust fan (as per IS code 374) having a each capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge. |
| 285 | NSSupply, erection, testing of 400mm Sweep 1300RPM Wall bracket fan with complete fixing arrangement. |
| 286 | LIGHT FIXTURE SUPPLY NS:-Supply of 20 W BATTEN 4ft long LED integrated batten made of ultra slim co-extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.White finish ABS end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. These end caps are snap-fitted to the fixture.High efficiency long life LED with lumen efficacy of 130 lm/W with viewing angle of 120º.Powered by an integral isolated low THD electronic LED driver ( SMPS based constant current supply) with output short circuit protection, surge protection.Can be fixed directly into the wall/ ceiling by means of mounting SS clips provided with the fixture. Lumen Output of 2110 lumens with System efficacy of >105lm/W .CRI >80, Color temperature 6500K, THD <20% and PF>0.95,IP20 . Life class of 35,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ. 20 W LED Batten 4ft long Modal like- CCS-102-20-65-SL-DP-NWH of Crompton or equivalent. |
| 287 | NS:- Supply of lighting fixtures of surface mounted 15W edgelit LED Round Downlighter luminaire.The LED source used shall be complying with LM80 standards & LED source efficacy >120 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;. The system lumen output of the luminaireof a minimum of 90 lms/W system efficacy with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.9, THD<20% and Surge Protection of atleast 2.5KV.15W Surface mounted LED down-lighter Modal like Bajaj BGSLO-SLEEK SURFACE 15W WH-SQ |
| 288 | NS:-Supply of lighting fixtures of surface mounted 12 W edgelit LED Round Downlighter luminaire.The LED source used shall be complying with LM80 standards & LED source efficacy >150 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;Highly reflective guide plate; The system efficacy of the luminaire upto 80 lms/W with color temprature of 3000/4000/5700/6500 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.9, THD<20% and Surge Protection of atleast 2.5KV.12W LED downlighter surface type Modal like Bajaj BGSLO-SLEEK SURFACE 12W WH-RD or equivalent. |
| 289 | NS:-Supply of lighting fixtures of 10W LED IP65 Bulkhead luminaire.The LED source used shall be complying with LM80 standards & LED source efficacy >150 lm/w. Epoxy white powder coated die cast aluminium housing; Opal polycarbonate diffuser; The system lumen output of the luminaireof a minimum of 900 lumens with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.95, THD<10% and Surge Protection of atleast 2.5KV 10W Bulk-head LED Light Modal like Crompton make LBHE-10-CBL |
| 290 | NS:- Supply of lighting fixtures of 36W (2"x2") LED panel surface mounted square LED luminaire with epoxy coated CRCA white powder coated housing, special translucent high transmitivity non yellowing (PMMA) Diffuser. Color temperature of 5700 degree kelvin (ANSI Bin rated) and CRI>80. The LED source used shall be medium/high power complying with LM80 standards & LED source efficacy >150 lm/w. Non-integral 3 stage isolated Driver with constant current constant voltage (CVCC), P.F >0.95 and Surge Protection of atleast >3 KV. System lumen output of the luminaire of a minimum of 100 lms/W 2"x2" LED Panel surface Mounted Modal like- LCTLSNE-36-FO-CDL of Cromptonor equivalent. |
| 291 | NS:-Supply of lighting fixtures ofHi-efficiency LED Floodlight Luminaire, Body made of di-cast aluminium and hi-precision optics with beam angles 60º / 90º, System power 100W, 230V, CRI>80, 327mm X 218mmX177, color temperature 3000K/4000K/5700K with IP65, THD<10% , PF>0.95 , operating voltage range: 110 - 305V, system lumen output: 14000lm, Surge protection: 5kV internal and 10kV external, Operating temperature: 0°C - 50°C, Epoxy Potted Driver for better Thermal and Electrical isolation of components, LED: Nichia/Cree/Bridgelux/Osram, IP65, IK08, driver efficiency>90%, LED burning hours: L70@50000hrs, Flood light 100 watt (Like BAJAJ AMAZE LED MODAL BJFL-100 WATT LED)or equivalent. |
| 292 | NS:-Supply of LED light Exit signage of double sided Green Acrylic Signage (Exit/Name of building part written and arrow marked on it) of suitable size with hanging arrangement with wall using super bright LED having power consumption of 3 watts minimum 2 hours battery back-up operating between 85-265 volts AC, making connections etc.complete as |
| 293 | LIGHT FIXTURE ERECTION HSR ITEM NO:- 23.20Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required |
| 294 | HSR ITEM NO:- 23.21Fixing of LED Down lighter 7 to 28 Watt on ceiling or in false ceiling including cutting/making hole in ceiling including making connections etc as required |
| 295 | HSR ITEM NO:- 24.1EARTHING AND LIGHTENING ARRESTOR 24.1.3Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. |
| 296 | HSR ITEM NO:- 24.1.5Extra for charcoal or coke and salt for G. I. plate or copper plate earth electrode. |
| 297 | HSR ITEM NO:- 24.1.6 Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground as strip earth electrode including soldering etc. as required. |
| 298 | HSR ITEM NO:- 24.1.7 Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required. |
| 299 | HSR ITEM NO:- 24.1.8Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. |
| 300 | HSR ITEM NO:-24.1.14 Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. staples of same size. |
| 301 | HSR ITEM NO:- 24.1.17Providing and fixing testing joints made of 20mm x 3mm thick G.I. strips 125 mm long with 4 nos. G.I. bolts and nuts with washers complete |
| 302 | DSR ITEM NO:- 6.14Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. |
| 303 | LT CABLE AND ACCESSORIES SUPPLY OF L.T. CABLE Supplying of following sizes of 1.1 KV grade multicorealuminium conductor XLPE insulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required. NS:-4Cx10 (AL Ard.) |
| 304 | NS:- 4Cx16 (AL Ard.) |
| 305 | NS:- 4Cx25 (AL Ard.) |
| 306 | NS:- 3.5Cx50 (AL Ard.) |
| 307 | NS:- 3.5Cx95 (AL Ard.) |
| 308 | NS:- 3.5Cx150 (AL Ard.) |
| 309 | HSR ITEM NO:- 24.2.2LT CABLE LAYING Laying of underground cable 0. 75 metre below ground level covered with sand and bricks including excavation and refilling of trenches.:- 24.2.2.350 Sq mm to 150 sqmm 2 to 4 Core |
| 310 | HSR ITEM NO:- 24.2.4Laying of underground cable in pipe /existing open/closed trench etc as 24.2.4.3 50 Sq mm to 150 sqmm 2 to 4 Core |
| 311 | HSR ITEM NO:- 24.2.5Laying and fixing of cable on surface/ cable tray etc as required:- 24.2.5.12.5 Sq mm to 10 Sq mm 2 to 4 Core |
| 312 | HSR ITEM NO:- 24.2.5.216 Sq mm to 35 sqmm 2 to 4 Core |
| 313 | HSR ITEM NO:- 24.2.5.3 50 Sq mm to 150 sqmm 2 to 4 Core |
| 314 | HSR ITEM NO:- 24.2.7 Supply and erection of suitable compression type brass cable glands for underground Cable :- 24.2.7.210 sqmm to 16s qmm Cable 2 to 4 Core |
| 315 | HSR 24.2.7.3 25 sqmm to 50 sqmm Cable 2 to 4 Core |
| 316 | HSR 24.2.7.470 sqmm to 95 sqmm Cable 3 to 3½ Core |
| 317 | HSR ITEM NO:- 24.2.8Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 24.2.8.3 10 sqmm |
| 318 | HSR 24.2.8.416 sqmm |
| 319 | HSR 24.2.8.525 sqmm |
| 320 | HSR 24.2.8.650 sqmm |
| 321 | HSR 24.2.8.995 sqmm |
| 322 | HSR 24.2.10 Supply and erection of cable route marker made of 50 cm long 1 O mm dia each 269 M.S. Rod welded/riveted at the top with 1 O cm dia 3 mm thick MS plate inscribed with "cable" word on it, having a cross arm 30 cm long of the same dia welded at the bottom, in exiting trench 45 cm below ground level. |
| 323 | HSR ITEM NO:- 23.22.6 Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work. 23.23.6.1 MS perforated cable tray painted with powder coating 100 X 5 X 2 mm |
| 324 | HSR 23.23.6.2 MS perforated cable tray painted with powder coating 200 X 5 X 2 mm |
| 325 | HSR 23.23.6.3 MS perforated cable tray painted with powder coating 375 X 5 X 2 mm |
| 326 | HSR 23.26.1 Supply and erection of Medium Voltage caution notice plate of size 200*150 each 85 mm in three languages. |
| 327 | HSR 23.26.3 Supply and erection of shock restoration chart in glass frame. |
| 328 | HSR 23.26.4 Supply & Erection of mild steel bucket stand suitable for 6 Nos. fire set 3067 buckets,(but without bucket) including the cost of welding and painting of complete stand will one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work (size 6"x4" made of GI pipe 32mm dia). |
| 329 | DSR 17.2INTELLIGENT FIRE ALARM SYSTEM DSR 17.2.1 Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card,minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. DSR 17.2.1.2 Two Loop Panel. |
| 330 | DSR 17.1.2 Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. |
| 331 | DSR 17.2.5 Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED,metallic cover complete with all connections etc as required. |
| 332 | DSR 17.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 333 | DSR 17.2.10 Supplying, installation, testing & commissioning of addressable fire control module complete as required. |
| 334 | DSR 17.2.14 Supplying, installation, testing & commissioning of addressable manual call point complete as required. |
| 335 | DSR 17.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. |
| 336 | DSR 17.1.1 Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required. |
| 337 | PUBLIC ADDRESS SYSTEM DSR 17.3.1 Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. |
| 338 | DSR 17.3.2 Supplying, installation, testing & commissioning of 6W ceiling speaker complete as required. |
| 339 | DSR 17.3.6 Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required. |
| 340 | DSR 17.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required. |
| 341 | DSR 17.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. |
| 342 | DSR 17.5.3 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. DSR 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm |
| 343 | (NS) UPS 0.01 Supply, installation, testing & commissioning of 20KVA Online UPS3phase input and 3phase output suitable for incoming 415 volts 3 phase +10% - 15%, 50Hz supply with inbuilt isolation transformer, Bypass & static transfer switch for automatic switch over, with built in technical protections like short circuits, over load/ low voltage cut off protection , without giving anyBreak of power. Along with SMF Batteries, Soft Start Facility , ECO Mode efficiency upto 99% , Advance Battery Management(Rocket/Exide/Amron quanta) giving a back up of 30 minutes on full load with each UPS, alongwith all accessories including interconnecting copper cables, Battery rack complete. The UPS should have input Thdi less than 3%, input power factor 0.9 , THDv not exceeding 3% , output voltage tolerance : less than 1% ( for static load) , with inbuilt isolation Transformer,as per specification make simens AG, APC , UNILINE NOTE : UPS system along with SMF BATTERY 12v/120AH(as per venders calculation) with its accessories like inter connectors & stand for 30minutesbatteries backupapprovedMAKE, DISCONNECTORFOR BATTERY PROTECTION, MS RACK, INTERLINKS ANDDC CABLE UPTO 5 MTRS FROM UPS TO BATTERIES. |
| 344 | AIR CONDITIONER SITC OF 1.5 TON, 5 star split Inverter type air conditioner complete in all respect with remote control and indoor/out doorunit etc. including the cost of petty material required to comlete the job in all respect. Make Panasonic, hitachi , daiken, bluestar (NS) |
| 345 | Supply of Automatic Voltage Stabilizer 5KVA Make Blue bird/Blue Guard/ V Guard (NS) |
| 346 | Supply of wall mounted MS stand for outdoor unit AC (NS) |
| 347 | Supply of Copper pipe with insulation as per standard Met tub/ Man dev/ Max Flow (NS) |
| 348 | Supply of Copper wire 2.5 sqmm (3 core) ISI marked Make Polycab/Havells (NS) |
| 349 | Supply of PVC drain pipe 25 mm dia with insulation UPVC Polypack/Prince/Prakesh (NS) |
| 350 | Supply of Flexible pipe2" white (NS) |
| 351 | Installation charges for Split type AC (NS) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
