Construction Of Shc Bejpur Block Itawa Distt. Kota- 1 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 2 Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto 1.5 Mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 Mtr. All kinds of soil 3 Filling in plinth with locally available river shingle under floors including watering ramming consolidating and dressing complete including cost of shingle sand. 4 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 5 Centering and Shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 6 Providing and laying in position specified grade ofcement concrete forall RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.M20 grade Nominal 7 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor Three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix 8 Centering & shuttering with plywood or steel Plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor Three level for :Columns, pillars, posts and struts etc. 9 Centering & shuttering with plywood or steel Plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor Three level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 10 Random Rubble stone masonry for foundation and plinth in Cement Sand mortar above 30 cm thick wall in :Cement Mortar 1 : 6 (1-Cement : 6-Sand). 11 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor Three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.M20 grade Nominal Mix 12 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Thermo-mechanically Treated bars (Conforming of relevent IS code) 13 Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 Mtr. and lift upto 1.5 Mtr. 14 Filling in plinth withlocally available good earth under floors including watering ramming consolidating and dressing complete including cost of Locally available good earth 15 Flyash Flyash Brick work with flyash Flyash Bricks of class designation 75 in superstructure above plinth level upto floor Three Level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) 16 Half Flyash Brick masonry in Superstructure , above plinth level upto floor three levelusing Flyash Bricks of designation 75 Cement mortar 1 : 6 (1 cement : 6 coarse sand 17 Random rubble dry stone Kharanja under floor. 18 Providing and fixing 15 to 20 mm thick Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12 mm (Av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of :Green / Black / Other granite. Above 3601 Cm2 Slabs 19 Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 20 Providing and fixing 1st quality MAT finished ceremic tile size 300 x 300 mm confirming to IS : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (Untile of Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of the complete (including the cost of cement mortor bed1:4). Category -A : Kajaria, Jhonson, Somani make 21 Providing & fixing vitrified paving tiles size 600 mm × 600 mm × 12 mm thick fix with cement mortar over 20 mm thich (1 Cement 4 Sand) laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (Untile or Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortor 1:4) Category -A : Kajaria, Jhonson, Somani make 22 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure A :30 mm thick commercial Veneer Both side 23 Add extra in Flush doors :For Double leaf 24 For External teak wood lipping on flush door30mmx6mm 25 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 26 Providing and fixing Anodised Aluminium Curtain rod with Aluminium brackets complete :25 mm dia 27 Providing and fixing T iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15 x 3 mm lugs, 10cm long embedded in cement concrete blocks 15 x 10 x 10 cm of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 28 Supply and fixing in cement mortar welded hand railing made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. 29 Providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 30 Providing and fixing M.S. sheet single leaf door shutter in angle iron frame 35 x 35 x 5 mm suitabilly diagonally braced with 25 x 3 mm flat iron above and below lock rail of size 50 x 5 mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats : including two coats of anit-corrasite red oxide primer paint. M.S. Sheet 18 S.W.G. 31 Supplying and fixing of Steel windows made out (65 x 40 mm) hollow metal pressed section of 1.25 mm thick sheet F4 & F7 standard rolled section conforming to IS 1038 with wholly openable shutter of 0.80 mm thick (out side & inside) opening C.R. sheet embossed panels, joints matted and flush welded with suitable hinges, steel lugs & screws with approved oxidised steel handles, fittings, peg stays (casement stays) etc. complete in all respect including providing 10 mm square M.S. bars 10 cm. C/C and applying priming coat of red oxide paint. 32 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20 x 3 mm with suitable screw at not exceeding 150 mm distance. 33 Providing batta (gola) 75 mm x 75 mm in cement concrete (1 : 2 : 4) including finishing with cement mortar 1 : 3 as per standard design. 34 Providing & laying Chequerred plain cement concrete embossed to specially manufactured non-slipping tiles of approved make 20 mm thick laid on 20 mm thick bed of cement mortar 1 : 6 jointed with neat cement slurry complete.Medium shade using approximately 50% white cement and 50% ordinary cement. 35 Plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :25 mm thick 36 Plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :20 mm thick 37 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand). 38 Applying priming coat :With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. 39 Painting with enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work. 40 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including Prepration of base and all scaffolding :New work (two or more coats) over and including scrapping and priming coat with cement primer. 41 Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. New work 42 Renewing glass panes, with putty and nails wherever necessary :4 mm thick plain glass panes. 43 Supplying and fixing dressed sand or other approved stone shelves, tands in cement mortar 1 : 3 with fine dressed edges : 35 mm thick. 44 Supplying and fixing in walls machine cut and polished stone shelves, tands andin CM 1:3 with machine cut edges :Kota stone 25 to 30mm thick. 45 Making of Health Wellness Center patern (Gola) including colour picture work in side for Fascasde branding includig material labour and T & P as pe direction Engineer-in-charge as per standared drawing/patern 46 Making of border of window Health Wellness Center as per given patern for Fascasde branding includig material labour and T & P as pe direction Engineer-in-charge up to window size 4x5.6 as per standared drawing/patern 47 Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite Work / Kota StoneFull Edge moulding 48 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completeBirla/J.K./Nerolac or ISO. As per direction of Engineer in charge. 49 Providing& fixing precast cement concrete coping 1: 2:4mix50mmthickcompleteas per specification 50 Finishing with 25 mm thick cement plaster on roofs in cement sand mortar 1 : 4 mix including water proofing compound @ 2% of cement used. with neat cement, finishing, curing etc. complete in all respect including making of 300 mm x 300 mm square. 51 Providing and fixing Indian Type white glazed vitreous china 1st quality W.C. Orissa pan (IS : 2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor. Size 580 x 440 mm 52 P & F WVC Wash Basin (1st quality IS : 2556 mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P.Pillar cock (IS : 8934 mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall. Size 510 mmx 400 mm 53 P & F WVC Wash Basin (1st quality IS : 2556 mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P.Pillar cock (IS : 8934 mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall. Size 550 x 400 mm dia for counter top 54 P & F Kitchen & Lab Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe upto floor level complete including cutting & making good the wall & floor. 1.0 mm thick Salem stainless steel AISI - 304 Kitchen sink of approved make (Nirali, Neel- Kanth, Jaina, Faber, Criystal ) With large waste couplings IS 13983-1994 Over all size Bowl Size(Inches) (Inches)24 x 18 x 8 20 x 16 x 8 55 P & F Looking Mirror with PVC Frame of approved (Atul/ Equivalent)Size 500 x 400 mm 56 Providing and fixing Towel Rail or Ring of approved quality / make. C.P. Brass Towel rail with brackets 450 x 20 mm. 57 Providing and fixing Soap Dish or Tray of approved quality / make. C.P. Brass 58 Providing and fixing Bath Shower of approved quality / make. C.P. Brass of Heavy & Superior quality 150 mm. 59 Providing & Fixing C.P. Flange for 15 mm dia taps 60 P & F bib cock (IS: 8931 mark) superior quality of approved make C.P. Brass bib cock, 15 mm nominal bore 61 Providing and fixing Inlet Connection (Angle, Valves) Superior quality, of approved make.for wash basin Gyser etc.C.P. Inlet connection 15 mm.Brass (IS: 8931 marked) 62 Providing and fixing 15 mm dia Connection Pipe of approved quality / make. PVC pipe with CP Brass nuts upto length 600 mm 63 Providing and fixing Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make. C P Brass half turn exposed 25 mm nominal bore 64 Providing and fixing Full -way Valve (IS : 778 Mark) or wheel valve of approved make. Gun Metal 15 mm nominal bore 65 Providing and fixing Full -way Valve (IS : 778 Mark) or wheel valve of approved make. Gun Metal 25 mm nominal bore 66 Providing and fixing PVC Storage tank confirming to IS : (12701 marked indicating the BIS license No) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. Long wash out pipe with plug & socket, including making connection etc. complete of approved design.500 Litres capacity 67 Hoisting Charges for each floor. 68 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 20mm nominal outer dia pipes 69 Providing and fixing 3-layer PP-R (Polypropylene random coplymer ) pipes SDR 7.4 UV stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of Engineer - in charge. (EXTERNAL WORKS)PN-16Pipe, 32 mm OD 70 Providing and Laying C.C. 1 : 5 :10 (stone aggregate 40 mm nominal size) upto haunches of S.W. pipes including 150 mm thick bed concrete as per Rajasthan PWD specifications : (Width W = Dia of pipe in Cm + 40 Cm.) concrete width to be reduced from width W at centre of pipe to 0 at top of pipe.(Excluding Cost of pipe )100 mm diaS.W. Pipe 71 Providing and fixing rigid PVC Pipe (IS : 4985 mark) Class II (4 Kg./Cm2) approved quality / makeincluding jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia 72 Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia Coupler (Socket) 73 Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia Plain Tee 74 Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia Bend 45° 75 Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia Bend 87.5° 76 Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia Vent Cowel 77 Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia Pipe Clip 78 Construction of Chamber in all types of soil with 300 mm thick masnory in CM. 1 : 6, 100 mm thick C.C. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in Cm 1 : 6, finished with floating neat cement 50 mm thick M-15 grade C.C. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 Mtr. Inside size 450 x 450 mm depth upto 0.5 M Cement coverwith frame 79 Construction of Chamber in all types of soil with 300 mm thick masnory in CM. 1 : 6, 100 mm thick C.C. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in Cm 1 : 6, finished with floating neat cement 50 mm thick M-15 grade C.C. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 Mtr. Inside size 600 x 450 mm upto depth of 0.5 M Cement cover with frame 80 Construction of Soakage well in all types of soil 300mm thick dry stone masonry, top and bottom 300 mm course in CM 1 : 6, 80 mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring earthwork complete as per approved drawing including disposal of earth within a lead of 50 Mtr. Size 240 cm dia outside & 240 cm depth 81 Construction of Septic Tank in all types of soil with 40 Cm. thick masonry in CM 1 : 6, 15 Cm. thickC.C. bed of 1 : 5 : 10, M-15 grade C.C. flooring & over stone slab covering, 80 mm thick slab, jointing of slab in CM 1 : 3 Ralthal, Kharanja, 50 mm thick stone partition walls, 20 mm thick plaster in CM 1: 6 finished with neat floating cement, 4 Nos C.I. foot rests of approved design, two No. 450 mm dia 25Kg. of each C.I. cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 Mtr. Size 200 x 100 x 130 cm (for 10 users) 82 Construction of Cement Concrete Chamber 125mm dia on depressed floor upto 45cm height from floor with : Stainless steel sheet grating 83 Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & its all accessories( J.B. , Bends etc.) , round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 . For additional technical parameters of products/ work , refer Annexure A attached with this BSR Short point (up to 3 mtr.) 84 Medium point (up to 6 mtr.) 85 Long point(up to 10 mtr..) 86 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & its all accessories( J.B. , Bends etc.) , round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modular switch, 3/ 5 pin 6 A modular socket, Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work refer Annexure A attached with this BSR On board 87 Medium point (up to 6 mtr.) 88 S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 20 mm 89 25 mm 90 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 2 x 2.5 sq. mm. + 1x1.5sqmm 91 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 92 Supplying and fixing of power plug point with Modularaccessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 18 SWG with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) [ as per detailed in respective item in BSR] , making connection , testing , etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 93 Providing & Fixing of modular type Step Fan regulator duly ISI marked (IS :11037) as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 5 step fan regulator 100 watt 2 Module 94 Providing & Fixing of Heavy duty capacitor start, copper woind Double ball bearing 900/1400 RPM single phase Exhaust fan as per PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached withthis BSR .300 mm sweep(900/1400 RPM) 95 Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <1000mA shown in LM79 report. The luminaire shall be BIS certified and T.C. certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumenmaintened,colorRendering Index>70 andCCT 5700K+355K. Surge protection shall be min = 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR LED Street Light fixture 70 Watt 96 Providing & Fixing of 240/415 V AC MCB with positiveisolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with thisBSR .Single pole MCB6 A to 32 A rating 97 Double pole MCB50-63 A rating 98 Providing & Fixing of IK09 recessed/surface mountingheavy duty horizontal type sheet steel of 1.6 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI/ ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR IP-43 Double door (single phase)6 Way (6 O/G +2 I/C ) 99 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 8 SWG copper Wire 100 Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of = 120 lm / watt, THD < 10 % ,p.f.=0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) ,maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure A attacheded with this BSRRecessed MountingLED Downlight 18/20W 101 Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of = 120 lm/Watt ,THD < 10 % , p.f.=0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure A attacheded with this BSRRecessed Mounting36W LED light fixture 2x2 with acrylic / prismatic front cover 102 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , Power Consumption of 18W/20W ,system lumen efficacy = 120 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% ,p.f.=0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure A attacheded with this BSR.4 LED Tube shape fixture 18/20 W (Polycarbonate Base) 103 SITC of chemical Gel earthing system of Dual Pipe Technology made of with B Class G I Pipe as per IS 1239 ( part-1):2004 of Medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below :-(a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, CPRI/ ERDA tested with RMS capacity of minimum 35- 40 KA for withstanding 1 second(b) To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab for low resistivity ( less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts©Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm.(d) Testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.(e) Self certificate for confirming above standards from OEM is mandatory. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR .With Pipe in Pipe Technology (Outer pipe dia. / Inner pipe dia. ) Minimum 100 mm dia borewellGI pipe 2000 mm long, 80 / 50 mm, Terminal 50mm x 6 mm GI Strip 104 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-(a) Material :- H4- Grade aluminium conductor of purity >99.6 %& as per IS:1554 P-I / IS :7098 P - I(b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures .(c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . Armoured Cable10.0 Sq. mm2.0 core 105 Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 1200 mm Sweep BEE 2 Star rated (service value >=4.5 to < 5 ) 106 Supply & Fixing of ABC Type (MAP 50) type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, with Dry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS 14609:1999. OEM will produce supplier certificate complete with squeeze grip release valve, locking arrangement, pressure gauge and bracket including initial fill and wall suspension complete in all respect. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 4 Kg 107 Supply Installationtesting&CommissioningofISOcertified manufacturer made Monoblock motor pump set ISI marked (IS:9079- 2002) with TEFC motor, motor should be IE2 class as per IEC 60034-2- 1: 2007, IEC 60034-30: 2008, & IS12615:2011. with Stainless steel Impellor, Stainless steel shaft, Mechanical seal, Single/Three phase ( 240 - 440 V ) permanent split capacitor type (PSC), fitted with thermal overload protection, . Including cost of hardware etc on existing platform complete. Pump shall have following HP Rating, phase, Head, minimum Discharge respectively complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 0.5 HP, 1-Ø, (3 - 18)Mtr, (100-26) LPM 108 Construction of tube well 100 Metre depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following size in all types of soils and over-burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part-I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube-well should have a throughout bore as per nominal dia of casing pipe. 200 mm dia nominal bore 109 Development of tube well as per IS specifications using suitable compressor to give sand free water for required yield of the gravel packed tube well. 110 Supply of ERW M.S. black casing pipe ISI marked (IS : 4270/1992) of grade Fe 410 of following sizes at site of work. Nominal bore of pipe200 (mm) 111 Supply & fixing tube well cover of M.S. Sheet (6 mm thick) with nuts and bolts complete for casing size. 200 mm dia 112 Supply & fixing M.S. clamp, set of 50 x 6 mm flat from iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 113 Providing & Fixing of Single Stage, water cooled, High Speed(2880 RPM), Horizontal, Centrifugal, Openwell Submersible pumps set pre filled with coolent water and fitted with mechanical seal - T/C Vs T/C, Thrust bearing shall be of carbon + S.S.The stator body of single phase pump shall be of SS and rest of all shall be of cast iron. All casting parts should be cathod electro deposition (CED) coated and other construction material should be confirming to IS : 14220: 2018 . The overall performance of pump shall confirm to BEE energy efficiency level of 3 star. Valid BEE certificate from OEM must be submitted for the same. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011, including making connection etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 2.0 HP, 1-Ø, (12 -25) Mtr, (350 - 115) LPM 114 Supplying andLaying ISImarkedP.V.C. insulated submersible cable as per PWD specification for electrical Works confirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 6.0 Sq.mm 3 core flat / Round 115 Providing & Fixing of HDPE pipe ISI mark (IS:4984/2016 ) for watersupply (suitable for submersible & jet pump) with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR 50 mm OD 6 kg / cm2 116 Construction of 185 cm. dia platform as per approved design and drawing of UNICEF. 117 Supply Installation testing & Commissioning of ISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR For single phase Submersible / Monoblockpump0.5 HP to 3.0 HP (DOL starter)
