Military Engineer Services-MES has published Periodical Services To Certain Building Alongwith Adm Block Of Nd (V) And Strengthening Of Structural Members And Connected Works To Enhance The Service Life Of Certain Building Of Area B Of Nd V Under Ge (I) Dm Visakhapatnam. Submission Date for this Tender is 04-10-2022. Building Repair Tenders in visakhapatnam Andhra Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or concrete wall etc including racking out joint hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 2 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 3 | M&L brick work with sub class "B" bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks complete all as specified and as directed. |
| 4 | Pre-cast cement concrete 1:3:6 type C1(using 20 mm graded crushedstone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed. |
| 5 | M&L for rendering15 mm thick plaster in CM (1:4) using SBR latex emulsion @ 4% by weight of cement onbrick or concrete surfaces of walls the surfaces even and smooth without using extra cement complete all as specified and directed.(Note:- Cost of SBR latex emulsion is included in quoted rate) |
| 6 | M&L for rendering10 mm thick plaster in CM (1:4) using SBR latex emulsion @ 4% by weight of cement onbrick or concrete surfaces of walls the surfaces even and smooth without using extra cement complete all as specified and directed.(Note:- Cost of SBR latex emulsion is included in quoted rate) |
| 7 | M&L rendering 10 mm thick in CM 1:6 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed |
| 8 | M&L rendering 5 mm thick in cement mortor 1:3 on concrete surfaces as in ceilings and finishing surfaces even and smooth without using extra cement complete all as specified and as directed |
| 9 | M & L preparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primer over a coat of cement based wall putty minimun thickness 1.5mm and cutting to smooth surfaces by sand paper complete all as specified and directed. |
| 10 | M & L preparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primercomplete all as specified and directed. |
| 11 | M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper over a coat of primer over a coat of cement based wall putty minimun thickness 1.5mm and cutting to smooth surfaces by sand paper complete all as specified and directed. |
| 12 | M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper over a coat of primercomplete all as specified and directed. |
| 13 | M&L for preparation of new plastered surface of ceiling and applying three coats of white wash on ceiling complete all as specified and as directed. |
| 14 | Complete removal of existing treatment of old decorated surfaces of wallsapplying two coats of cement based white wall putty of minimum thick ness 1.5 mm in two coats to make the surface even & smooth complete all as specified &directed. |
| 15 | M&L for finishing walls with textured exterior paint of required shade: New work( two or more coats applied @3.28ltr/10sqm) over and including priming coat of exterior primer applied@ 2.20 kg/10 sqmover a coat of cement based wall putty minimun thickness 1.5mm and cutting to smooth surfaces by sand paper complete all as specified and directed. complete all as specified and as directed. |
| 16 | M & L Complete removal of existing treatment of old decorated surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer over a coat of cement based wall putty minimun thickness 1.5mm and cutting to smooth surfaces by sand paper complete all as specified and directed. |
| 17 | M & L Complete removal of existing treatment of old decorated surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primercomplete all as specified and directed. |
| 18 | M & L Complete removal of existing treatment of old decoratedplastered surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primer over a coat of cement based wall putty minimun thickness 1.5mm and cutting to smooth surfaces by sand paper complete all as specified and directed. |
| 19 | M & L preparation of old plastered surfaces ofwalls and applying one coat of exterior emulsion paint (weather coat) complete all as specified and directed. |
| 20 | M&L preparation of old plastered or unplastered surfaces of ceiling and applying two coats of white washing complete all as specified and directed. |
| 21 | Complete removal of existing treatment of old decorated surfacesof wall and applying three coats of white wash complete all as specified and directed. |
| 22 | M &L preparation of old plastered surfaces of walls and applying one coat cement base paint complete all as specified and directed. |
| 23 | M&L peparation of oldsteelsurfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of zinc chrome primer complete all as specified and as directed. |
| 24 | Demolition of cement concrete (un reinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) and removing debriesout side to Dockyard premesis complete all as specified and asdirected. |
| 25 | M&L PCC 1:2:4 type B1 type (using 20 mm graded crushed stone aggregate) as in foundation filling and mass concrete etc complete all as specified and directed. |
| 26 | M&L 75 mm thick cement concrete 1:3:6 Type C2 (using 40 mm graded crushed stone aggregate) in floors (plinth protection) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 27 | Dismantling portions ofreinforced cement concrete work asordered / chipping of unsound concrete to a depth / thickness of 50 mmand above thicknessinrespect ofgallery cover slabs, side duct walls, beams, cope point, electrical panel base slabs etc., and similar work on jetty gallaries, gallary drains etc., (work in restricted movement area below ground level and requires de-wateringetc., ) completeall as specified and as directed including removal of rubbish out side Dock Yard premisses. |
| 28 | M&L reinforced cement concrete 1:1.5:3 Type A1 (using 20 mm graded crushed stone aggregate) as in columns, pillars, piers posts and struts and simillar work etc including necessary form workcomplete all as specified and directed. |
| 29 | M&L MS TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia as reinforcement complete all as specified and directed. |
| 30 | Material & labour for chipping (20mm to 50mm)of existing damaged, crakced, spalled & loose portion of concrete ofthe RCC memberscompletely till the reinforcement is exposed and sound concreteis observed by using mechanical means and manual chisels and further the surface is cleaned with water jet, again clean the surface with blower to remove all loosefine particles present in the surfacesand for removal of dust and loose particles complete all as specified and as directed.. (Note : Work shall be executed on any floor up to fifth floors or 20m heightof buildings) |
| 31 | M&L for preparation of exposed surafces of rustedsteel reinforcement with metal wire brush,cleaning the rustedsurfaces free from loose rust and applyingrust remover cum passivator (Sika Rustoff 100 @ 0.20Kg / Sqm or any other equivalent approved make of E -in -C"s branch) on surface of existing reinforcement with brush to the rusted reinforcemnet , removing rust with flex after 24 hours of application of rust remover with the help of wire brush, sand paper and throughly washed with water with the help of pressure jet and allowing surfaces of steel it todry complete all as specified anddirected.. Note:- Area of cleaned reinforcement steel bar shall only be consideredfor payment Density: 1.01 Kg/l at 300C |
| 32 | Preparation of surfaces of steelof reinforcement by cleaning thruoghly and proving , mixing andaplyingzinc anti-rust agent as per manufacturers method of applicationtorebar corrosion protection system to reinforcement( Sika / Fosroc/BASF/ Dr sunanda)@3.75Kg/Sqm surfaceof steel reinforcement in two coats complete all as specified and as directed.. |
| 33 | Material & labour applying a coat of Polymer modified cementious bonding coaton the concrete surfaces with one part of Styrene Butadiene Rubberlatex emulsion (SBR latex) manufactured by M/s Fosrocchemicals orequivalent in M/S Sika India Pvt. Ltd. / M / S Choksey Chemicals Pvt. Ltd. / M/S Mapei Const Product India Pvt Ltd. / M/S THermax Ltd/ M/S STP / M/S Dr Sunanada / M/SBASFor any other approved manufacturer of E-in-C"s branch with four parts of water and six parts of cement by weight. Coverage of SBR latex-0.25Ltr / sqm for one coat complete all as specified and directed. |
| 34 | Material & labour for providing Shear connectors and Anchoring by drilling 16 mm dia holes up to depth of 100mm in concrete surfaces and fixing 10 mm diaTMT bars L shaped anchor rods as shear connectors by using Fosroc Lokfix chemical (Mixofbase and hardener of the polyester resin)in defective concrete area ofthe slab / column / beams / chajjas / lintel etcor any other structural member as per site requirement after cleaning the drilled hole by using water jet and after dryingclean the surface with blower to remove all loosefine particles present in the hole.The Mix of base and hardener of the polyester resin shall be prepared by thorough mixing of base & hardener by the help of spatula. After preparing the mix the holes shall be filledto a minimum depth of 1/3rd of the hole with the prepared polyester resin and the reinforced bar shall be inserted to full depth of hole and extra length of the reinforcement bar shall be bent into the concrete to maintain proper cover to the reinforcement complete all as specified and directed. |
| 35 | M&L for applying polymer modified, cementitious mortar fibre reinforced, single component shrinkage controlled, (Renderoc SP40 of Fosroc Makeor equivalent in M/S Sika India Pvt. Ltd. / M / S Choksey Chemicals Pvt. Ltd. / M/S Mapei Const Product India Pvt Ltd. / M/S THermax Ltd/ M/S STP / M/S Dr Sunanada / M/SBASFor any other approved manufacturer of E-in-C"s branchhaving a compressive strength of 40 MPA strength for reparing of RCC members like columns, Beams / Slab soffits etc. complete all as specified and directed. |
| 36 | Material & laobur for application of polymer modified reinstatement mortar 20mm thick in isolated places of repair works of RCC members with Rendroc S2 of M/s Fosroc make or equivalent in M/S Sika India Pvt. Ltd. / M / S Choksey Chemicals Pvt. Ltd. / M/S Mapei Const Product India Pvt Ltd. / M/S THermax Ltd/ M/S STP / M/S Dr Sunanada / M/SBASFor any other approved manufacturer of E-in-C"s branchhaving a compressive strength of 40 MPa complete all as specified and directed. |
| 37 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm but n.exc 4 Sqm each complete all as specified and directed. |
| 38 | Supply and fixaluminium door shutter with chowkats mad out of hollow aluminium sections as mentioned below, each shutter having 2 Nos. ‘D’ type aluminium handles of 200 mm long,2 Nos. aluminium tower bolts of 200 mm long and 1 No. mortice lock of 6 lever with key in duplicate, regulated by double action hydraulic floor door spring, shutter partly glazed with 5 mm thick sheet glass and partly paneled with 12 mm thick pre-laminated particle board fixed with glazing clips, rubber beadings and aluminium beading all complete all as specified and as directed. Chowkat size:101.60 x 44.45 x 2.40 mm (1.608 Kg./RM appx.) ShutterTop rail: 114.30 x 2.15 mm thick (1.836 Kg./RMappx.) Bottom rail :150.00 x 2.20 mm thick (2.376 Kg./RM appx.) Middle rail:83.50 x 1.70 mm thick (1.243 Kg./RM appx.) Vertical rail :85.00 x 1.80 mm thick (1.302 Kg./RM appx.) |
| 39 | S&F factory made UPVC white colour sliding window three track of area not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67 mm). Sliding mesh Sash (42mm x 57mm) sliding interlock (one vertical lenght in each shutters) (45.5mm x 28mm), Glazing bead (24.5mmx 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 + - 0.2mm thick galvanised steel frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch Lock of zinc alloyed (white powder coated ), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and as directed.. Note: the unit rate quoted by the contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose. |
| 40 | S&F sheet glass 4.0 mm thick ordinary quality fixed with UPVC beads in squares n.exc 0.5 Sqm in each pane complete all as specified and directed. |
| 41 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed. |
| 42 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for partitions (Fixed portions) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDMrubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all completeall as specified and directed including taking out old one.. |
| 43 | S&F sheet glass 5.0 mm thick ordinary quality fixed with UPVC beads in squares n.exc 0.5 Sqm in each pane complete all as specified and directed. including taking out old one.. |
| 44 | M&L 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with snap beading with aluminium frame partitions work a complete all as specified and directedincluding taking out old one.. |
| 45 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removingrubbish outside ND(V) premises complete all as specified and as directed. |
| 46 | M&L light shade non skid ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but notexceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 15 mm thick 1:6 cement morter including roughning surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3 kg of cementper sqmcomplete all as specified and as directed. |
| 47 | M&L light shade non skid ceramic tiles 7-8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 sqm but notexceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 15 mm thick 1:6 cement morter including roughning surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3 kg of cementper sqmcomplete all as specified and as directed. |
| 48 | Material & labour for granite (any type) work (table rubbed and polished) 18 to 20 mm thick in working platform,cooking platfoormand like including cutting in oval shape for oval type WHB below counter basin etc,. in cement mortar (1:4) including pointing in white cemnt (1:2) using marbledust with admixture of pigment to match complete all as specified and as directed. |
| 49 | Material & labour for rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc., complete all as specified and as directed. |
| 50 | Dismantling mild steel work of any description complete all as specified and directed. |
| 51 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channel, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc ., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 52 | M&L MS rolled section of grade Fe-290 Gde -E (beam, tee, angle channel or flat sections) as in framed bracket (framed), including bending welding as neessaryincluding distance pieces, cleats etc. complete all as specified and directed. |
| 53 | S&FSteel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 54 | M&L preparation of new or previously untreatedsteel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 55 | Dismantling plain galvanised MS Sheet / corrugated steel sheeting any guage or any thickness in roof coverings etc complete all as specified and as directed. |
| 56 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in chajjas, roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 57 | Note: The aboveitemsare to be executed with proper safety gears and necessary double scaffolding arrangements to carry out the repair works. Thequoted rates shall be accordingly considered for all the safety measure, scaffolding, height, lead and lift in the items. No extra will be admissible on this account |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
