Supply Of Ferritic Steel Coilferritic Steel Coil, Ferritic Steel Sheet 5X1250 X 3000 Mm., As Per Drawing / Specification: Rdso Spec No.C-K201 Grade X2crni12 ( 409M ) Table 1&2, Optimum Weight 2Rdso Spec No.C-K201 Grade X2crni12 ( 409M ) Table 1&2, Optimum Weight 2Mt+-10%.Mt+-10%, Packing Instruction: As Per Standard Packing. It Should Be Ensured That Item Should Not Rub During Transportation. The Item Should Be Packed With Adequate Strength. Transit Damage , If Any , Shall Be At The Cost Of Supplier. , Ferritic Steel Sheet 3X1250x3100 Mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X2crni12 ( 409M ) Table 1&2.Optimum Weight 2Mt+-10%Heat Treatment Condition 2B As Per Table-5., Packing Instruction: As Per Standard Packing. It Should Be Ensured That Item Should Not Rub During Transportation. The Item Should Be Packed With Adequate Strength. Transit Damage , If Any , Shall Be At The Cost Of Supplier. , Ferritic Steel Sheet 4X1250x3100 Mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X2crni12 ( 409M ) Table 1&2.Optimum Weight 2Mt+-10% Heat Treatment Condition 2B As Per Table-5., Packing Instruction: As Per Standard Packing. It Should Be Ensured That Item Should Not Rub During Transportation. The Item Should Be Packed With Adequate Strength. Transit Damage , If Any , Shall Be At The Cost Of Supplier. , Ferritic Steel Sheet 6X1250x3500mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X2crni12 ( 409M ) Table 1&2.Optimum Weight 2Mt+-10%. , Ferritic Steel Coil 2X1250mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X2crni12 ( 409M ) Table 1&2Heat Treatment Condition 2B As Per Table-5, Coil Id 450-800, Od 1000-1300Mm, Coil Weight 2.4-10 Tonnes, Packing Instruction: Stainless Steel ( Austenitic & Ferritic Steel Coils Etc. ) : The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provisions As The Barest Minimum: I ) Coil Should Be Wrapped With A Layer Of Water Proof Paper Throughout The Whole Length. Ii ) Coil Should Be Wrapped With A Layer Of Biodegradable Sheet. Iii ) Outer & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv ) Side Of The Coil Should Be Covered With Card Board Sheet. V ) After This Whole Coil Should Be Wrapped With Biodegradable Plastic Sheet Of Suitable Thickness. Vi ) The Inner Edge Of The Coil Should Be Protected By Gi Ring , Followed By Another Iron Ring. Vii ) Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii ) Coil Should Be Securely Strapped With Minimum 5 Steel Bands Through The Eyes Of The Coil And Minimum 3 Steel Bands On The Circumference Of The Eye. Ix ) Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting / Stacking. , Ferritic Steel Sheet 8X1250x3000mm., As Per Drawing / Specification: Is:6911- 1992, Grade X04cr12 ( 405 ) ., Packing Instruction: As Per Standard Packing. It Should Be Ensured That Item Should Not Rub During Transportation. The Item Should Be Packed With Adequate Strength. Transit Damage , If Any , Shall Be At The Cost Of Supplier. , Ferritic Steel Sheet 2X1250x2100mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X2crni12 ( 409M ) Table 1&2 Optimum Weight 2Mt+-10% Heat Treatment Condition 2B As Per Table-5., Packing Instruction: As Per Standard Packing. It Should Be Ensured That Item Should Not Rub During Transportation. The Item Should Be Packed With Adequate Strength. Transit Damage , If Any , Shall Be At The Cost Of Supplier. , Ferritic Steel Coil 2.5X1250mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X2crni12 ( 409M ) Table 1&2 Heat Treatment Condition 2B As Per Table-5, Coil Id 450-800Mm, Od 1000-1300Mm, Coil Weight 2.4-10 Tonnes., Packing Instruction: Stainless Steel ( Austenitic & Ferritic Steel Coils Etc. ) : The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provisions As The Barest Minimum: I ) Coil Should Be Wrapped With A Layer Of Water Proof Paper Throughout The Whole Length. Ii ) Coil Should Be Wrapped With A Layer Of Biodegradable Sheet. Iii ) Outer & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv ) Side Of The Coil Should Be Covered With Card Board Sheet. V ) After This Whole Coil Should Be Wrapped With Biodegradable Plastic Sheet Of Suitable Thickness. Vi ) The Inner Edge Of The Coil Should Be Protected By Gi Ring , Followed By Another Iron Ring. Vii ) Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii ) Coil Should Be Securely Strapped With Minimum 5 Steel Bands Through The Eyes Of The Coil And Minimum 3 Steel Bands On The Circumference Of The Eye. Ix ) Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting / Stacking.
