Supply Of Austenitic Steel Coilaustenitic Steel Coil, Austenitic Steel Coil 1.25X1250mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X5crni1810 ( 304 ) Table 1&2, Heat Treatment Condition 2B As Per Table-5, Coil Id 450-650Mm, Od 1000, Kapurthala-Punjab

Supply Of Austenitic Steel Coilaustenitic Steel Coil, Austenitic Steel Coil 1.25X1250mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X5crni1810 ( 304 ) Table 1&2, Heat Treatment Condition 2B As Per Table-5, Coil Id 450-650Mm, Od 1000-1300Mm, Coil Weight 5-10 Tonnes., Packing Instruction: Stainless Steel ( Austenitic & Ferritic Steel Coils Etc. ) : The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provisions As The Barest Minimum: I ) Coil Should Be Wrapped With A Layer Of Water Proof Paper Throughout The Whole Length. Ii ) Coil Should Be Wrapped With A Layer Of Biodegradable Sheet. Iii ) Outer & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv ) Side Of The Coil Should Be Covered With Card Board Sheet. V ) After This Whole Coil Should Be Wrapped With Biodegradable Plastic Sheet Of Suitable Thickness. Vi ) The Inner Edge Of The Coil Should Be Protected By Gi Ring , Followed By Another Iron Ring. Vii ) Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii ) Coil Should Be Securely Strapped With Minimum 5 Steel Bands Through The Eyes Of The Coil And Minimum 3 Steel Bands On The Circumference Of The Eye. Ix ) Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting / Stacking. , Austinitic Steel Sheet 3X1250x3300 Mm., As Per Drawing / Specification: Rdso Spec No.C-K201, Grade X5crni1810 Table 1&2, Heat Treatment Condition 2B As Per Table-5., Packing Instruction: As Per Standard Packing. It Should Be Ensured That Item Should Not Rub During Transportation. The Item Should Be Packed With Adequate Strength. Transit Damage , If Any , Shall Be At The Cost Of Supplier. , Austenitic Steel Coil 2X1250mm., As Per Drawing / Specification: Rdso Spec No.C-K201 Grade X5crni1810 ( 304 ) Table 1&2 Heat Treatment Condition 2B As Per Table-5, Coil Id 450- 800Mm, Od 1000-1300Mm, Coil Weight 2.4-10 Tonnes., Packing Instruction: Stainless Steel ( Austenitic & Ferritic Steel Coils Etc. ) : The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provisions As The Barest Minimum: I ) Coil Should Be Wrapped With A Layer Of Water Proof Paper Throughout The Whole Length. Ii ) Coil Should Be Wrapped With A Layer Of Biodegradable Sheet. Iii ) Outer & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv ) Side Of The Coil Should Be Covered With Card Board Sheet. V ) After This Whole Coil Should Be Wrapped With Biodegradable Plastic Sheet Of Suitable Thickness. Vi ) The Inner Edge Of The Coil Should Be Protected By Gi Ring , Followed By Another Iron Ring. Vii ) Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii ) Coil Should Be Securely Strapped With Minimum 5 Steel Bands Through The Eyes Of The Coil And Minimum 3 Steel Bands On The Circumference Of The Eye. Ix ) Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting / Stacking. , Austenitic Steel Coil 1.7X1100mm., As Per Drawing / Specification: Rdso Spec No.C- K201, Grade X5crni1810 ( 304 ) Table 1 & 2, Heat Treatment Condition 2B As Per Table-5, Coil Id 450-650Mm, Od 1000-1300Mm, Coil Weight 5-10 Tonnes., Packing Instruction: Stainless Steel ( Austenitic & Ferritic Steel Coils Etc. ) : The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provisions As The Barest Minimum: I ) Coil Should Be Wrapped With A Layer Of Water Proof Paper Throughout The Whole Length. Ii ) Coil Should Be Wrapped With A Layer Of Biodegradable Sheet. Iii ) Outer & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv ) Side Of The Coil Should Be Covered With Card Board Sheet. V ) After This Whole Coil Should Be Wrapped With Biodegradable Plastic Sheet Of Suitable Thickness. Vi ) The Inner Edge Of The Coil Should Be Protected By Gi Ring , Followed By Another Iron Ring. Vii ) Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii ) Coil Should Be Securely Strapped With Minimum 5 Steel Bands Through The Eyes Of The Coil And Minimum 3 Steel Bands On The Circumference Of The Eye. Ix ) Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting / Stacking.

Refer document

INR 5000000.0 /-

Refer document