Indira Gandhi National Centre For The Arts-IGNCA has published Providing And Installing Portable Porta Cabin For The Use Of Green Room Near Amphitheatre, Ignca New Delhi. Submission Date for this Tender is 25-08-2022. Auditorium Construction Tenders in delhi Delhi. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 24-Aug-2022 | Clarification | Other | 25-08-2022 |
| Sl. No. | Item Description |
| 1 | WALL10FT HT : Providing and fixing 4MM THICK EXTERIOR GRADE ALUMINUM COMPOSITE SHEET AND INTERNAL SIDE 8MM CEMENT FIBRE BOARD DULY PAINTED AND WITH MS PIPE FRAMEWORK 40X40MMx2MMWITH 50 MM ROCKWOOL INSULATION ALL COMPLETE INCLUDING SCREWS, CLAMPLS OR OTHER ACCESSORIES OR FIXTURES AS REQUIRED FOR FIXING THE WALL PANEL , as per the direction of Engg Incharge. MS frame work will be paid seprately.The joint of ACP shall be sealed with an sealing substance that ensure watertight of panles.For opening deduction wil be made as per rule. |
| 2 | ROOF: Providing and fixing PRE COATED GALVANISED IRON SHEET SANDWICH PANELS WITH TRAPEZODIAL SHEET TOP AND PLAIN SHEET BELOW AND WITH 30-35 MM POLYUTHERNE INSULATION HELD ON MS PIPE FRAMEWORK 40X40MMx 2 mm. and as per the direction of Engg Incharge. MS frame work will be paid seprately. roof shall be projected from the walls as per direction. |
| 3 | ROOF PROJECTION :-Providing vertrical facia of required height with ms frame of required size, the facia shall be covered with 4 mm thick ACP sheet, all complete as required on site. MS frame work will be paid seprately. |
| 4 | FALSE CEILING: providing and fixing of false ceiling of size 600X600MM GRID WITH GI POWDER COATED SECTION USIGN 8MM THICK PVC LAMINATED GYPSUM TILES SUSPENDED WITH GI WIRE 4mm all comlplete as per direction of Engg Incharge. |
| 5 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in aluminium item ) With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 6 | Providing and fixing of following itemsfor windows and door1.Aluminium tower bolt 250*10 mm- 04Nos2.Door Stopper- 02 Nos 3. Huydraulic door closer- 01 nos4.100 mm aluminium round handle- 04 5. Alunmimium aldrop-01 Nos and other required fitting and fixtures for door and windows |
| 7 | Electrical points: wire shall be used 1.5 mm for 5 amp, 2.5 mm for 15 amp & 4mm for AC, The quantity required as per no of fittings. Electrical fittings- 5 LED tubelight, 2 wall Fan, 2 charging points, 1 exhaust Fan (as approved by Engg Incharge ) are to be supplied & provided make- wire- polycab, havells, fittings& fixtures- Crabtree, havells,syska, philips, |
| 8 | Floor-Ms square pipe of size 40x40x2 mm to make frame of size 600x600 mmwith 20 mm fibre board and Pvc venyl flooring of 3mm thickness and of approved quality. Including screws,clips and other fixtures as required. MS frame work will be paid seprately. |
| 9 | Toilet fittings- one wall hanging Wc with cistern & Health faucets, one wash basin 18 inch , with all fittings & fixtures and one mirror. Connection of water and sewer should be done by the vendor from the nearest point All the plumbing, sanitary,included, CPVC pipe & fitting of 15 mm dia , except external sewer line which will be paid seprately.Make- Jaquar,Cera, Hindware,or as apparoved by Engg Incharge. |
| 10 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes. |
| 11 | Aluminium window and door Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required.Powder coated aluminium (minimum thickness of powder coating 50 micron) kg |
| 12 | Providing and fixing 100 mm PVC pipe for sewerline including excavating/ removing of existing paver block and refilling the trench and refixing the paver block .it also include making of connection in existing manhole& repair etc all complete as per direction of Engg Incharge. |
| 13 | Providing and fixing of 20 mm cpvc pipe for water connection, including excavation and reflling,including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps , This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints all complete as per direction of Engineer in Charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
