Procurement Of Spares For Esp System Procurement Of Spares For Esp System , Inner Arm Assembly For Cerm & Eerm Consists I ) Inner Arm Half-2 Nos. Ii ) Hex Bolt M16x90-1 Nos. ( Half Threaded, Grade 4.6 ) Iii ) Hex Bolt M16x40-1 Nos. ( Half Threaded, G, Chhabra-Rajasthan
TDR : 33403832
Tender Notice
Corrigendum Details
BOQ
Expired
Chhabra
Rajasthan
Corrigendum : Procurement Of Spares For Esp System Procurement Of Spares For Esp System , Inner Arm Assembly For Cerm & Eerm Consists I ) Inner Arm Half-2 Nos. Ii ) Hex Bolt M16x90-1 Nos. ( Half Threaded, Grade 4.6 ) Iii ) Hex Bolt M16x40-1 Nos. ( Half Threaded, G
INNER ARM ASSEMBLY FOR CERM & EERM consistsi)Inner Arm Half-2 Nos.ii)Hex Bolt M16x90-1 nos.(half threaded, grade 4.6) iii) Hex Bolt M16x40-1 nos.(half threaded, grade 4.6) iv) hex nuts M16-2 nos.( grade 4.6) (MOC EN-08 for flats ) as per drawing / sample
2
OUTER ARM FOR CERM (Total weight 8Kg+/-2.5-5%)i)Roller wheel- 1 no.ii) Arm-2 nos.(10 mm thick flat)iii)Washer- 2 nos.(45x28x3 mm)iv)Pin- 2 nos. (L114xdia25mm round bar)as per drawing / sample*MOC EN-08 for roller wheel & pin and MS for arms & washers
3
OUTER ARM FOR EERM(Total weight 5.3Kg +/- 2.5-5%)i) Roller wheel-1 no.ii) Arm-2 nos.(10 mm thick flat)iii)Washer- 2 nos.(45x28x3 mm)iv)Pin -2 nos. (L114xdia25mm round bar)(*MOC EN-08 for roller wheel & pin and MS for arms & washers) as per drawing / sample
4
SLEEVE BEARING BRACKET ASSY. Consistsi)Sleeve Bearing/CI Liner (in two halves),C.I.FG-210- 2NOS.ii)HT hex Nut+ Bolt M12x50- 2nos.iii)MS Strip (40x40x10)- 4 nos.iv)Weld type-6 (MOC FOR LINER SET IS AS PER IS-210 FG-210) as per drawing / sample
5
SET RING (Material EN-08)ID-50+/-0.5mm , OD-75.0m, Height-18.00mm Grub Screw,M10x15 mm-2nos.
6
GRIP COUPLING FOR EERM (MOC EN-08 for flat) consistsGrub Screw m10x25 mm -1 no.as per drawing / sample
7
SHAFT SLEEVE 50 Ø MM (EN-24)Inner dia -50+/- 0.5 mmOuter dia-70+/- 0.5 mmLength- 130+/-1 mm Thickness-10 mm,
8
SHAFT SLEEVE 40.5 Ø MM (EN-24)Inner dia -40+/- 0.5 mmOuter dia-50+/- 0.5 mmLength- 120+/-1 mm Thickness-5 mm
9
PLAIN BEARING ASSEMBLY FOR RAPPING MECHANISM CONSISTSi)Lower Half-01(IS-210-FG 200)ii) Upper Half -01 01(IS-210-FG 200)iii)Hex Bolt M16X120 mm-02 Nos (4.6 Grade half threded)iv)Hex Nut M16 -02 nos.( 4.6 Grade)*Casting must be free of all kinds of casting defects.
10
TOP SLEEVE FOR EMMITING SHAFT DIA.40 MM (MATERIAL EN-8)
11
END SHAFT FOR CERMDIA 50mmLenth : 790mmHole Dia 17mmMaterial : EN-8 as per drawing / sample
12
GD screen material as per IS 513,CRCA sheet 2.5mm (as per Drawing),material of hook MS, 4.00mm thick
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
