|
| 1 | PART-A-CIVIL WORKS |
| 2 | EARTH WORK IN EXCAVATIONinall types of soil ,includingsoft or hard murrum, but excluding soft and hard rock, using mechanical means (Hydraulic Excavators)/Manually for depth upto 1.5m,including cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, and stacking of excavated material within a lead of 100m, including providing temporary supports to existing facilities viz., service lineslikewater pipes, electric under ground cablesetc. if any all complete as per the specifications and directions of Engineer-in-Charge. |
| 3 | Same as Item No: 20 above, but for depth beyond 1.5m and upto 3.0m. |
| 4 | BACKFILLING after execution of the work to the proper grade and level with selected approved available excavated soil fromsoil heaps within a lead of 100m,including re-excavating the deposited soil excavated earlier, breaking clods, laying at all depths and heights in layers of thickness not exceeding 150 mm, watering, rolling and ramming by manual methods/mechanical compactors, dressing, trimming etc. in foundations, plinths, etc.all complete as per directions of Engineer-in-Charge. |
| 5 | TRANSPORTING & DISPOSING the surplus earth & debris including shrubs and vegetations from construction area (beyond the initial lead of 100m) to the corporation/municipality designated area up to a lead of 7km including re-excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths & heights, stacking, levelling and dressing both areas (viz., from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directedby Engineer in Charge.( Note: If measured by stacks 30%voids will be deducted.) |
| 6 | Supplying and filling M SAND of specified quality underfootings,pedestal etc. for all depthsincluding the cost of sand, labour charges,tools and tackles,royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layersnot exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/ or other equipment to specified levelall complete as perspecifications and directions of Engineer-in-Charge. |
| 7 | Supplying and filling approved QUARRY DUST of specified quality under floors, plinths, etc. for all depthsincluding the cost of quarry dust, labour charges, tools and tackles, royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layer not exceeding 150 mm, watering, ramming, compacting with mechanical compactors to specified levelall complete as perspecifications and directions of Engineer-in-Charge. |
| 8 | Providing and laying in position PLAIN CEMENT CONCRETE (PCC) 1:4:8 with 40mm & down size graded aggregate for levelling course/fill under footings,pedestal etc., for all depthsincluding all tools and tackles, labour and material charges, curing, compacting,in any shape, level, thickness, position and finishing the surface smooth/rough etc., complete as directed by Engineer-in-Charge. |
| 9 | Providing&laying DRY RUBBLE SOLING (Hard Core) with 20 to 40 mm size metal, under foundations/ Ground floor slab (Grade slab) etc., including filling recesses by grit, stone chips & approved murrum, watering, dressing, compacting with mechanical compactors etc., complete as per drawings, specifications and as per thedirections of Engineer-in-charge. |
| 10 | Providing, mixing and laying in position RCC 1:1.5:3 with 20mm and down graded coarse aggregates as per IS 456:2000 with a minimum cement content of 400kg/Cu.m.using 53 grade Ordinary Portland Cement in SUB-STRUCTURE for all depths upto FFL level including cost of admixtures if used, labour charges, tools and tackles, providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth & even surface and providing neat cement wash etc.,(excluding the Cost ofReinforcement and Shuttering), etc. all complete as specified and directed by Engineer-in-Charge. |
| 11 | Providing, mixing andlaying in position RCC1:1.5:3 with 20mm and down graded coarse aggregates as per IS 456:2000 with a minimum cement content of 400kg/Cu.m. using 53 grade Ordinary Portland Cement in SUPER-STRUCTURE for all heightsabove FFL level including cost of admixtures,labour charges, tools and tackles,providing pockets, openings, recesses, chamfering, wherever requried, vibrating, tamping, curing and rendering if required to give a smooth & even surface, providing neat cement wash, etc. (Excluding the Cost of Reinforcement, Shuttering), etc. all complete as specified,and directed by Engineer-in-Charge. |
| 12 | Providing and fixing straight / inclinedCENTERING AND SHUTTERING in SUB STRUCTURE for all depths upto FFL Levelincluding strutting, bracing, propping etc. keeping the same in position during concreting and de-shuttering & removal of the same after specified period as per specifications.keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byEngineer-in-Charge complete with all tools and tackles,materials, labour charges, consumables etc. (Form work shall be supplied by the contractor and shall remain the property of the contractor) |
| 13 | Providing and fixingstraight / inclined CENTERING AND SHUTTERING in SUPER STRUCTURE at all heights above FFL Level including strutting, bracing, propping etc. keeping the same in position during concreting, de-shuttering & removal of the same after specified period as per specifications etc.,keeping necessary provision for inserts, projecting dowels,or any other fixture etc. all complete and as specified and directed byEngineer-in-Charge complete with all tools and tackles,materials, labour charges, consumables etc. (Form work shall be supplied by the contractor and shall remain the property of the contractor) |
| 14 | Supplying, fabricating and placing in position HIGH STRENGTH DEFORMED STEEL BAR REINFORCEMENT of grade Fe500 for RCC work, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractor\"s own 16 Standard Wire Gauge(SWG) black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, overlaps, chairs, spacers, lifting hooks etc for all heights & depths etc. all complete as directed by Engineer-in-Charge. |
| 15 | Providing and laying BRICK MASONRY IN SUB STRUCTUREup to FFL level using cement mortar 1:5 (1 Cement:5 Coarse Sand)for alldepthsincluding the cost of materials, labour, tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings, curing, etc. all complete as per specifications, and as directed by Engineer-in-Charge. |
| 16 | Providing and laying BRICK MASONRY IN SUPER STRUCTUREabove FFL level using cement mortar 1:5 (1 Cement:5 Coarse Sand)for allheightsincluding the cost of materials, labour,tools and tackles, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape and size,embedding the fittings,curing, etc. all complete as per specifications, and as directed by Engineer-in-Charge. |
| 17 | Providing and laying HALF BRICK MASONRY in cement mortar 1 : 4 (1 Cement : 4Coarse Sand) for all depths and heightsincluding cost of materials, cement, labour, scaffolding, sampling, testing, supplying and placing 2 no. 8 mm dia. diarebars at every fourth course, sealing the gap between masonry and soffit of the beam / slab, embedding the fittings and fixtures, curing, etc. all complete as per specifications, and as directed by Engineer-in-Charge. Note:- The cost of Reinforcement shall be paid seperately under relevant items. |
| 18 | Providing 15mm THICK CEMENT PLASTERin cement mortar 1:4 (1Cement:4 Fine sand by volume) onbrick masonry/ concrete surfaces including preparation of base, cleaning, chipping, scaffolding, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles, material costs etc. as per specifications and asdirected by the Engineer-in-Charge. |
| 19 | Providing 12mm THICK CEMENT PLASTERin cement mortar 1:4 (1Cement:4 Fine sand by volume) onbrickmasonry, concrete surfacesincluding preparation of base, cleaning, chipping, scaffolding if required, finishing, curingincludingmouldings and providing grooves in plaster, bands, mouldings etc. as specifiedfor all depths and heights including labour charges, tools and tackles,material costs etc. as per specifications and asdirected by the Engineer-in-Charge. |
| 20 | Providing 6mm THICK CEMENT PLASTER in cement mortar 1:3 (1Cement:3 Fine sand by volume) on Roof Ceilings, concretesurfaces including preparation of base, cleaning, chipping, packing of electrical works,scaffolding, finishing, curing etc.for all heights complete with all labour charges,material costs,tools and tackles etc.as per specifications and as directed by the Engineer-in-Charge. |
| 21 | Providingandapplying two coats of INTERIOR EMULSION with wall putty of approved make of any shades/coloursover one coat of primer asper the specifications includingnecessaryscaffolding and surface preparation consisting of application of Plaster of Paris punning over entire surface, filling all holes and depressions with white cement, applying a coat of primer, two or more coats of oil based putty(as per manufacturer\"s recommendations)sand paperingetc. in walls and roof ceiling, complete as per specification and as directed by Engineer-in-Charge. |
| 22 | Providing and applyingWEATHER PROOF TEXTURED EXTERIOR PAINT on RCC /brick Walls / plastered surface etc. of Asian ,Nerolac,Berger or any other equivalent approved make, one coat of primer andtwo or more coats (to give a smooth and even shade)of anti-fungal, water proof, anti flakingweather proof paintof approved quality and shade including painting cartoon characters/kid friendly images in the elevation as per requirement etc.This alsoincludesnecessaryscaffolding, cleaning and surface preparation, preparation consisting of application of Plaster of Paris punning over entire surface,filling all holes and depressions with Plaster of Paris, applying a coat of primer, two or more coats of oil/water based putty(as per manufacturer\"s recommendations) sand papering etc., all complete as per specification and as directed by Engineer-in-Charge. |
| 23 | Supplying, transporting, storing, fabricating & erecting in position bolted and / or weldedSTRUCTURAL STEEL WORKS like angles, channels, beams, plates, Square/Round bars, pipes, tubesfor ladders at all heights & levels and locations including all builtup sections/ compound sectionsmade out of rolled sections and / or plates / bent plates for curb edging etc., cutting to required size, straightening/bending if required, edge preparation,cleaning, scrapping & welding, preheating, finishing edges by grinding, fixing in line and level,including preparing the surface for painting,surface cleaning, wire brushing, removal of mill scale, dust, rust, oil or grease etc complete along with providing paint system as follows:(a) Applying inorganic zinc silicate coat 75 micron DFT(b) Two coats of Epoxy primer paint 75 micron DFT each(c) Two coats of Anti Rust epoxy top coat paint 100 micron DFT each as per manufacturer\"s specifications and as directed by Engineer-in-Charge. Note:-One coat of Zinc silicate and one coat of Epoxy primer shall be applied on structural steel surfaces after grit blast cleaning in workshop prior to erection as per specifications and as directed by Engineer-in-charge. Supply of all materials in contractor\"s scope. |
| 24 | Providing and laying of premium quality Glazed/Matt Finish VITRIFIED TILES of size 800x800of Kajariaor approved equivalent, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles,4\"skirting all around as per drawing ,along with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of Engineer-in-Charge as per drawing. |
| 25 | Providing and laying of premium quality ANTISKID CERAMIC TILES of size 300x300 ofapproved make floor matt finished colour, nonslip, decorative type of tiles, approved make with bed of 20mm thick cement mortar 1:3 in line and level including cleaning the finished surfaces with oxalic acid including skirting out the joints, flush pointing of joints of tiles with cement paste/grout mixed with colour pigments matching the shade of tiles, with material costs,tools and tackles, labour charges etc.as per specifications, standards and instructions of Engineer-in-Charge. |
| 26 | Providingand laying COLOURED GLAZED CERAMIC TILES FOR WALL/DADO(Grade I quality), ofapproved make & shade including 20 mm thick cementbedding C.M. 1:3, PVC beading with matching colour, pointing and finishing exposed joints with white cement/matching colour pigment,etc., including cleaning the finished surface, all complete with material costs, tools and tackles, stagings labour charges as perspecifications and as directed by Engineer-in-Charge. |
| 27 | Providing and fixing in position Two Track Two Panel Sliding uPVC WINDOWS (with clear 5mm thick glass), white in colour including all fixtures, fastenings, sliding system, sliding handle with flush lock, EPDM gaskets, wool pile etc., making recesses in brick/concrete surfaces and making good the same after fixing all complete as per directions of Engineer-in-Charge. |
| 28 | Providing and fixing bright finished brass 100mm MORTICE LATCH AND LOCK ISI marked with four levers and a pair of polished stainless steel decorative handles(size of handles to match the door size) with necessary screws etc. complete (Best make of approved quality) as specified by Engineer-in-Charge. |
| 29 | Providing and fixing SOLID SHEET VINYL WALL PAPER of minimum 150GSM , embossed with textured effect pasted to wall using flake adhesive to be fixed on to the walls/partitions neatly with out shrinkage and bubbles and should have seamless joints. The design , shade and colourshall be as directed by Engineer in Charge. |
| 30 | Providing and Fixing ISI marked, overall 30mm thickBLOCK BOARD FLUSH DOOR SHUTTERS of Kutty or approved equivalent decorative type, consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on one side with decorative1mm thick laminate and another side with water proof laminate of archidply or approved equivalentincluding providing and fixing\"T\" type second class teakwood perimeter beading fixed by means of approved quality neoprene based adhesive and nailing @ 300mm max., providing and fixing 125mm long stainless steel butt hinges [for each shutter (vertical spacing not exceeding 600mm) including providing wooden filler/sealer, stainless steel lock with status indicator, teak wood lipping, aluminium butt hinges, 3mm thick anodised(anodic coating not less than15 microns) aluminium kicking plate fixed with screws for entire door width on either side of door for a height of 600mm, fixing with door frame,door bush, finishing etc . all complete as directed by Engineer-in-Charge. |
| 31 | Providing and fixingSECOND CLASS TEAK WOODEN FRAMESfor doors, windows, ventilators,Cupboards etc. for all heights including all labours, tools, tackles, cutting, shaping, jointing, applying a coat of bituminous paint on concealed surface, wood primer on exposed surface, fixing in masonry/RCC by means of 300mm x 25mm x 6mm thick M.S. Hold fasts screwed to frame @ 600mm max vertically and grouted with 1:2:4concrete by volume in min. 350mm x 100mmx100mm sized hole made in masonry/96mm long, 12mm dia M.S. dash fastner, painting with two coats of approved shade and make (ICI or equivalent) synthetic enamel paint over appoved quality primer coat, finishing etc. all complete as dirercted by Engineer-in-Charge. |
| 32 | Supplying and fixing30 mm THICK WPC DOOR SHUTTER withFrame including towerbolts on either sides,handlesincluding metal hinges and all other fittingsetc. complete as per directions of Engineer-in-Charge. |
| 33 | Providing & laying to required slope CEMENT CONCRETE SCREED of mix 1:1.5:3 (1 cement : 1.5 Coarse sand: 3 Coarse aggregates 12.5mm and down graded aggregates) using 53 grade OPC inRoof Terrace etc. laid to required slope and thickness & inclusive of curing/pond curing, brooming with wire brush, finishingetc.all labours, tools and tackles complete as per drawing, specification & as directed by Engineer in charge. |
| 34 | Providing and Laying WATER PROOFING MEMBRANE to roof of Atactic poly propylene (APP) with non-Woven polyster reinforcement having thin poly ethylene foil of approved quality inculding cleaning, crack filling, rendering and necessary fixing arrangements as per manufacturer\"s specifications, rate shall include supplying & sprinkling Pea-Sized gravel or grit devoid fine sand over member complete as per drawing, specifications and as directed by Engineer-in-charge. (The thickness of Atactic Poly propylene (APP) membrane to be considered as 4.0mm) |
| 35 | Providing and fixing in positionSTAINLESS STEEL KITCHEN SINK SINGLE BOWL WITH DRAIN BOARD glossy finish folded edge of Nirali-Elegance ultra or approved equivalent make of Bowl size 510mmx 410mmx 200mm made of min stainless steel sheetsupported onM.S. Brackets, supply, fixing ofM.S.brackets, fasteners, sinkcock (quarter turn range) of parryware-agate or approved equivalent, C.P. Angle valve of parry ware, C.P. brass waste, PVC drain pipewith heavy bottle trap of Parry ware or approved equivalent make, inlet pipe, drain pipe , rubber plug, connections to floor trap with unions and all accessories as required to complete including cutting and making good the walls where ever required, painting all exposed metallic surfaces with two coats of approved shade and quality synthetic enamel paint over an approved quality priming of red oxide zinc chromate, making good of all damaged work, finishing etc., all complete as directed by Engineer-in-Charge. |
| 36 | Providing and fixing 18mm thick machine cut, mirror polished, premoulded and pre-polished machine cut GRANITE for PLATFORMSof approved qualityfor wash basin/ vanity counters,pantry etc.of required size of approved shade, colour, and texture laid 20mm thick base cement mortar 1:4 (1 Cement:4 M Sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including machine polishing to edge to give high gloss finish, providing machine cut opening for fixing wash basin, rubbing, curing, moulding & nosing etc. complete at all levels as directed by Engineer-in-Charge. |
| 37 | Providing & fixing WHITE FLOOR MOUNTED EUROPEAN WATER CLOSET (EWC) WITH DUAL FLUSH CISTERN of Parry ware-Petitieor approved equivalent make including Cistern, Cistern Lid, Antimicrobial seat cover with lid, fitting,slim line health faucet with hose & hook,bibcock andother standard accessories, all fittings and fixturesincluding cutting walls/ floors making good of same, making inlet/outlet connection, finishing, etc.all complete as per the directions ofEngineer-in-Charge. |
| 38 | Providing & fixing WHITE FLOOR MOUNTED KIDSEUROPEAN WATER CLOSET -SINGLE PIECE SUIT (including closet,flushing cistern,soft close seat cover and all fittings)of Parryware Kids C8941 or approved equivalent make including all fittings,slim line health faucet with hose & hook, bibcock and other standard accessories, all fittings and fixturesincluding cutting walls/ floor, making good of same,making inlet/outlet connection, finishing, etc.all complete as per the directions ofEngineer-in-Charge. |
| 39 | Providing and fixing white glazed earthenware china KIDS WASH BASIN with pedestal of make Parryware make C8943 or approved equivalent of 530x290X520 mm sizeincluding approved cast iron/MS brackets , one 15mm dia. CP brass pillar cock, rubber plug with CP brass, 32mm CP waste fitting of standard pattern pipe with 32mm dia. PVC pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by Engineer-in-Charge. |
| 40 | Providing and fixing white glazed earthenware china WASH BASIN of make Parryware/hindware with antisplash rims on 3 sides of 550x450mm sizeincluding approved cast iron/MS brackets , one 15mm dia. CP brass pillar cock, rubber plug with CP brass, 32mm CP waste fitting of standard pattern pipe with 32mm dia. PVC pipe with bottle trap, cutting wall, floors and making good the same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint overred oxide zinc chromate(approved quality) making all connections, finishing etc. all complete as directed by Engineer-in-Charge. |
| 41 | Providing and fixingMIRROR of superior glass of Parryware or approved equivalent complete with CP brass screws, fastners and washers complete as directed by Engineer-in-Charge. |
| 42 | Providing and fixing600 mm long CP rodTOWEL RAIL of parry ware make or approved equivalent complete with brackets fixed to wooden cleats with CP Brass screws with concealed fitting arrangement of approved quality and colour all complete as specified by Engineer-in-Charge. |
| 43 | Providing and fixing C.P. brass SHOWER ROSE 100mm Diameter with 15 to 20mm inlet of parryware or equivalent approved including 230mm shower arm, making inlet and outlet connections, etc. completeas directed by Engineer-in-Charge. |
| 44 | Providing and fixing of CP brass TWIN ROBE HOOK of Parryware/approved equivalent including fixing the coat hook including drilling holes on plastered/tiled wall and doors fixing the coat hook with CP screws including all fittings & fixtures, labour tools and tackles, making the good the same, all completeas directed by Engineer-in-charge. |
| 45 | Providing and fixing15 mm nominal outer dia. & SDR11 CHLORINATED POLY VINYL CHLORIDE(CPVC) PIPES (Exposed on wall) , of approved equivalent make having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings & accessories including fixing the pipe with clamps at 1m spacing. This includes jointing of pipes & fittings with one step CPVC solvent and testing of joints complete as per directions of Engineer-in-Charge. |
| 46 | Same as Sl. No:-450 above, but for 20mm nominal outer dia. Pipes |
| 47 | Same as Sl. No:-450 above, but for 50mm nominal outer dia. Pipes |
| 48 | Providing and fixing 80mm dia. nominal boreunplasticised rigidPVC(UPVC PIPE) - Sch. 40 water line pipes (concealed pipeline) conforming to IS: 13592 type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion (single socketed pipes) with necessary fittings /accessories etc.all complete as per specifications and as directed by Engineer-in-Charge. |
| 49 | Same as Sl. No. 480 above, but for 100mm dia. nominal bore pipes. |
| 50 | Same as Sl. No. 480 above, but for 150mm dia. nominal bore pipes. |
| 51 | Providing and fixing 150 mm dia. RIGID PVC RAIN WATER PIPESwith MS holder clamps including fixing/embedding into masonry/concrete, providing connections like shoes, vents, specials, bends etc. fixing in perfect plumb etc. all complete including jointing with bonding solution of approved quality and make with pressure rating of 4 kg/ sq.cm including clamps, connections, etc. complete as per specifications and as directed by Engineer-in-Charge. |
| 52 | Providing and fixing100 mm dia.RIGIDPVC PIPES with pressure rating of 4 kg/ sq.cm of approved brand including all fixtures as vent pipe for septic tank, machine welded, rubber ring jointsusing approved lubricant, making hole in the slaband restoring the same to the original condition including provision of COWL in the septic tank vent pipe etc. complete as per specifications and directions of Engineer-in-Charge. |
| 53 | Providing and fixing TWO WAY BIBCOCK single lever range with Flange of Parryware or equivalent approved 15mm nominal bore CP including fixingand connections, etc. completeas directed by Engineer-in-Charge. |
| 54 | Providing and fixing Parryware or equivalent approved 15mm nominal bore brass BIBCOCK including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by Engineer-in-Charge. |
| 55 | Providing and fixing Parryware or equivalent approved 15mm nominal boreBrass Angle Valve including breaking walls and making good the same, inlet and outlet connections, etc. completeas directed by Engineer-in-Charge. |
| 56 | Providing and fixing 50 mm nominal bore gun metal GATE VALVE (lever type) lever of approved quality including all fittings etc. complete as directed by Engineer-in-Charge. |
| 57 | Supplying and laying custom (prefabricated) PVC FLOOR SUMPS/ FLOOR TRAPS fabricated out of 110mm dia. 6 kg/cm2 class PVC pipes with inlet and outlets from 40mm upto 75mm, including providing water seal, fixing to a perfect level, laying cement concrete in 1:3:6 mix CP/PVC colour grating with frame at 4mm below finished floor level making holes in masonry or concrete cutting surfaces conveying all dismantled portions and clearing the site,making leak proof joint and testing, etc. complete and as directed by Engineer-in-Charge. |
| 58 | Providing, hoisting and fixing in position RCC PRECAST ELEMENTSwithreinforced cement concrete grade 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate(20mm & down size) withOPC 53 grade cementfor shelves in kitchen and store room, storm water drain and septic tank cover Slabs for all leads, levels, shapes and thickness including all moulds, shuttering and centering, vibrating, tamping, curing, chamfering, providing lifting hooks,levelling, aligning and fixing/laying in position, all complete (excluding cost of Reinforcement) and as directed by Engineer-in-Charge. All material including cementto be supplied by the contractor. |
| 59 | Supply and installation of CYLINDRICAL TRIPLE LAYER WHITE VIRGIN PLASTIC STORAGE TANK OF CAPACITY 1000 LITRES of Sintex or approved equivalent onground floor roof with lid and making necessary cutout /holes for inlet, outlet and overflow pipes, necessary connections and sealing all joints properly,all complete. including, fixing, transportation to work site all complete as per drawings and directions of Engineer-in-charge. |
| 60 | DEMOLISHINGthe existing building in the location approx.120Sq.m (taking all necessary safety precautions) for allheights and depths above plinth level including dismantling of flooring, fixtures, doors, windows, brickwork,columns,truss,purlin, structural steel items etc. all complete as directed by Engineer-in-Charge. This includes demolishing foundation including raft and underlying layers.All unserviceable material should be disposed atCorporation/Municipality designated area upto a lead of 7kmas directed by the Engineer-in-Charge. All serviceable materials shall be the property of contractor. |
| 61 | Supply of UNSKILLED LABOURto carry out petty works not assessable for measurements/minor repair works, on day-to-day basis. The rates shall include ESI, PF, payroll cost and allowances, fringe benefits, overhead supervision, profits andhand tools etc. all complete as directed by Engineer in Charge. |
| 62 | Supply of JCB on hire basis on all days including Sundays on 8 hrs.shift including driver,assistant /fuel/oil/lubricants /all consumables etc. complete. The quoted rate should include mobilization, operator crew\"s/driver /assistant cost,tools, tackles etc., as directed by the Engineer-in-charge. |
| 63 | PART-B-ELECTRICAL WORKS |
| 64 | Supply and laying of PVC wires:The scope of work includes supply of following size of PVC insulated, copper conductor and laying in the existing surface / recessed, PVC / steel conduit / PVC casing and capping as required including connection in fans, switches, light fitting, sockets etc, as per the specifications of this tender and directions of Engineer-In-Charge. Note: Only ISI marked cables shall be used. |
| 65 | 1.5 sq.mm |
| 66 | 2.5 sq.mm |
| 67 | 4 sq.mm |
| 68 | 6 sq.mm |
| 69 | Supply and laying of PVC conduits:The scope of work includes supply and laying of following size of PVC conduit along with the accessories to be used for installation in surface/concealed as required, as per the specifications of this tender and directions of Engineer-In-Charge. Note: Only ISI marked conduits shall be used. |
| 70 | Upto 25 mm |
| 71 | EARTH PIT:The scope of work includes supply , installation , testing and commissioning ofearth pitwith 65 MM dia 3000 mm longearth electrodes , complete wih all necessarymaterialsincludingexcavation of earth pit , fillingwith charcoaland salt, back filling , providing cement (concrete) slab for earth pits, paintingand markingof earth pit nosand connectionsincluding all labour and materialsand as per the specifications of this tender and directions of Engineer-In-Charge |
| 72 | EARTH FLAT / WIRE:The scope of work includes supply, installation and connection of following GI earthing strips along the cable trenches or cable trays or fixing to walls or structures and for connecting equipments to the plant grid including welding at joints, providing anti-corrosive paint or bitumen and jute covering for welded portion, clamping and necessary hardware for connection etc., including all labour and materials, as per approved drawings, specification of this tender and direction of Engineer-in-charge. |
| 73 | 40 x 6 GI earth Flat |
| 74 | 8 SWG wire for earthing |
| 75 | Supply and Installation ofSwitch & Sockets:The scope of work includes supply of the below mentioned switch & sockets as per the specifications of this tender and directions of Engineer-In-Charge. |
| 76 | Supply and installation of 5/6 Amps socket outlet |
| 77 | Supply and installation of 5/6 Amps Switch |
| 78 | Supply and installation of 16 Amps Socket with Switch |
| 79 | Wall Mounted Bulb Holder with LED lamp:The scope of work includes supply and fixing of Wall Mounted Bulb Holder along with Min 15 W LED lamp and other related accessories as per the directions of Engineer-in-Charge |
| 80 | Tube light fitting:The scope of work includes supply and fixing of LED L.FIXT ELITE PRIDE PLUS 18 W 6500 K1, Cool Daylight (CDL), Decorative Slim Linear 4’ LED Batten fittings with bulb of havells catalogue or equivalent ,including civil work (if any) required for installation, all complete with labour and materials, as per the specifications of this tender and directions of Engineer-In-Charge. |
| 81 | SUPPLY AND FIXING OF MODULE BOX:Supply and fixing of plastic/metal boxes of following sizes with all accessories including necesssary base frame plates/ mounting , cover plates, etc.,suitable for fixing decorative switches of type roma or equivalent make in Havells/Siemens/Anchor/L&T |
| 82 | 1 or 2 module box |
| 83 | 4 module box |
| 84 | 6 module box |
| 85 | 8 module box |
| 86 | 12 module Box |
| 87 | CEILING FAN:The scope of work includes supply, installation, testing and commissioning of 1200mm sweep ceiling fan ofBajaj / crompton greaves / khaitan / usha / havells make of following sweep withceiling fan and regulator, including wiring the down rod of standard length (upto 30 cm) with 1.5 sqmm, PVC insulated, copper conductor, single core cable etc., as required,, as per the specifications of this tender and directions of Engineer-In-Charge. |
| 88 | Supply and Installation of 12 way DB:The scope of work includes supplyand installation of 12 way DB with 40 A MCB, 40 A RCCB and 8 Nos of 10 A MCB as per the specification of this tender and directions of Engineer-in-Charge. This shall be inclusive of all MCB and RCCB |
