|
| 1 | Excavating in trenches n exc 1.5m wide and not exc 1.5m in depth for laying of cables, foundation and getting out in hard/dense soilcomplete all as specified and directed by Engineer-in-Charge. |
| 2 | Cement concrete type D-2,1:4:8 (40mm graded crushed stone aggregate ) as infilling and mass concrete as in sub floors complete all as specified and directed by Engineer-in-Charge. |
| 3 | RCC type B-1 , 1:2:4(Nominal Mix)(20 mm graded crushed stone aggregate) as infoundations, plinth beam bases for columns etc, basement slabs, under-reamed piles and mass concretecomplete all as specified and directed by Engr-in-Charge. |
| 4 | RCC type B-1 , 1:2:4(Nominal Mix)(20 mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge. |
| 5 | RCC type B-1 , 1:2:4(Nominal Mix)(20 mm graded crushed stoneaggregate) as inSlabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and directed by Engr-in-Charge. |
| 6 | RCC (Nominal Mix) type B-1 1:2:4 (20 mm graded crushed stoneaggregate) as inBeams, cantilevers, bressummers, lintels over 1.5m spancomplete all as specified and directed by Engr-in-Charge. |
| 7 | Mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with MS wire (annealed) not less than 0.9mm dia for securing with clipscomplete all as specified and directed by Engr-in-Charge. |
| 8 | All as per item No 7 above but 5mm dia and over upto and including 10mm dia in stirrups spacers and binderscomplete all as specified and directed by Engr-in-Charge. |
| 9 | Form work to sides of concrete foundations, plinth beams and similar work, rough finished surfaces of concrete, flat,complete all as specified and directed by Engr-in-Charge. |
| 10 | Form work to sides ofcolumn, posts, pilllars, columns and stanchionsrough finished surfaces of finished concrete Square, rectangular or polygonal complete all as required at site or directed by Engr-in- Charge. |
| 11 | Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work; not exceeding 200mm thick(Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed by Engr-in-Charge. |
| 12 | Form work to sides and soffits of floor or roof baems lintels etc rough finished surfaces of concrete, square rectangular or polygonal in shapecomplete all as specified and directed by Engr-in-Charge. |
| 13 | Brick work with sub class \"B\" modularsize bricks straight or curved on plan exc 6 m mean radius in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. |
| 14 | Taking down cement plaster on brick work or stone walls including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. |
| 15 | Preparation of newly plastered surfaces and applying two coats of acrylic exterior emulsion paintcoloursas approved of any shade/colour in camouflage pattern over a coat of primeras per manufacture instructions complete all as specified and directed by Engr-in-Charge. |
| 16 | Rendering 15mm thick cement plaster on fair faces of brick work or concrete surface and finished even and smooth in cement morter 1:4complete all as specified and directed by Engr-in-Charge. |
| 17 | Rendering 15mm thick cement plaster on fair faces of brick work or concrete surface and finished even and smooth in cement morter 1:6complete all as specified and directed by Engr-in-Charge. |
| 18 | Rendering 5mm thick cement plaster on fair faces of brick work or concrete surface as in ceiling and finished even and smooth in cement morter 1:3complete all as specified and directed by Engr-in-Charge. |
| 19 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed by Engr-in-Charge. |
| 20 | Spreading levelling in layer not exceeding 25cm thick icluding watering and well ramming complete all as specified and directed by Engr-in-Charge. |
| 21 | Removing excavated material n exc. 50m and depositing wheredirected at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge. |
| 22 | Hardcoreusing broken stone boulders not exceeding 63mm deposited spread and levelled in layersnot exceeding15 cm thick watered and rammedto a true surfaces complete all as specified and directed by Engr-in-Charge. |
| 23 | Cement concrete 75mm thicktype D-2 1:4:8(40mm graded crushed stone aggregate) as insub basecomplete all as specified and directed by Engr-in-Charge. |
| 24 | Non skid glazed ceramic tiles 7 to 8 mm thick (Square/rectangular) are of each tile exceeding 0.06 Sqm but not exc 0.11 Sqm, in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in cement mortar (1:4) complete all as specified and directed by Engr-in-Charge. |
| 25 | Glazed ceramic coloured tiles 450x300mmx7mm thick onvertical surfaces of walls, set and jointed in neat cement slurry and pointed in coloured cement to match to tiles including provision of rendering 10 mm thick in cement mortar (1:4)complete all as specified and directed by Engr-in-Charge. |
| 26 | Light shade vitrifiedtiles10mm thick (square/rectangular) area of each tilenot exceeding 0.36 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15mm thick screed bed or bedding layer in cement mortar 1:4and dismantling/demolition on existing surface complete all as specified and directed by Engr-in-Charge. |
| 27 | Preparing surfaces plastered first coat on undecorated suraface and including white washing 3 coats on ceilingcomplete all as specified and directed by Engr-in-Charge. |
| 28 | Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-Charge.NOTE:- During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement. |
| 29 | Supply and fixing offactory made solid PVC moulded door shutter, 30 mm thick (stiles) with 4 raised panel design with 2 mm thickmoulded PVC sheet on the front face& 2mm plain colour PVC sheeton back facewith particle board core complete all as specified and directed by Engr-in-Charge. |
| 30 | Supply and fixing ofbutt hinges 100mm medium weightcold rolled mild steelcomplete all as specified and directed by Engr-in-Charge. |
| 31 | Supply and fixing of 125mm aluminium handles, cast type anodised complete all as specified and directed by Engr-in-Charge. |
| 32 | Supply and fixing of 200 mm longAluminium anodosied , barrel tower bolt of extruded section complete all as specified and directed by Engr-in-Charge. |
| 33 | Supply and fixing of15 mm bore medium grade galvanisedsteel tubing with all fittinglaid in trenchs complete all as specified and directed by Engr-in-Charge. |
| 34 | Supply and fixing 20 mm bore medium grade galvanisedsteel tubing with all fittinglaid in trenchscomplete all as specified and directed by Engr-in-Charge. |
| 35 | Supply and fixingin repair bib taps, fancy type, chromium plated, cast copper alloy ISI marked with crutch or butter fly handle high pressure screwed down screwed for iron pipe of 15mm bore complete all as specified and directed by Engr-in-Charge. |
| 36 | Supply and fixing ofpillar tap cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with or without letterd hot or cold with long screwed, shanked and fly nuts screwed for iron pipe 15mm dia complete all as specified and directed by Engr-in-Charge. |
| 37 | Supply and fixing ofPVC connection 15 mm size PTMT nuts length 600mm complete all as specified and directed by Engr-in-Charge. |
| 38 | Supply and fixing of110 mm borePVC (SWR) pipe single socketedin any lengthwith rubber ring joints laid in trenches complete all as specified and directed by Engr-in-Charge. |
| 39 | Supply and fixing of75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenchsas required complete all as specified and directed by Engr-in-Charge. |
| 40 | Supply and fixing of 75mm dia PVC (SWR) bends with oval accesse door with rubber ring joints fixed as requiredcomplete all as specified and directed by Engr-in-Charge. |
| 41 | Supply and fixing of 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified and directed by Engr-in-Charge. |
| 42 | Supply and fixing of Vitreous china Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing andfixing plugs, beddding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screw, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe including with all fittingscompleteall as specified and directed by Engineer-in-Charge |
| 43 | Granite (of any type), 18- 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixer of pigment to match with marble shade including making full curving the edges completeall as specified and directed by Engineer-in-Charge |
| 44 | Designer coloured, polished floor paver tiles of size 300 x 300mm x 25mm thickwith mixture of white cement and pigment set, jointed and pointed in neat cement slurry over and including screed be 20mm thick in cement mortar 1.6 any type and in any pattern (Pattern consist of combination two or more different colour tiles etc.) including demolition of existing surfacecomplete all as specified and directed by Engr-in-Charge. |
| 45 | Supply and fixing ofbeveled edge mirror of selected glass mounted on 6mm tick AC buildingboard or commercial plywood and fixed to wooden on plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr-in-Charge. |
| 46 | Supply and fixing ofWHB, vitreous china, white, decorative type, oval shapeincliding cutting for and pinning in ends of brackets orerecting stand includingwaste pipe complete all as specified and directed by Engr-in-Charge. |
| 47 | Preparation of newly plastered surfaces andapplying two coats of oil bound distemper, including a coat of wall care putty 2-3 mm thickcomplete all as specified and directed by Engr-in-Charge. |
| 48 | Cutting openings, through brick walls for door, window and other openings or enlarging existing openings.converting window into door openings, etc. or cutting out defective brick work for under-pinning, includingproviding, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m built in cement mortar complete all as specified and directed by the Engr-in-charge. |
| 49 | Supply and fixing of powder coated aluminum door using 96.6mmx44.8mm x1.6mm aluminium chowkhats 84.0 x 44.7mm x 1.6mm section vertical styles 101.60 x 44.88 x 1.6 mm rails mounted on floor spring mortice lock ,02 Nos tower bolt 150mm, sliding bolt 300mm long 01 No, door handles and fittings, bottom panel with 12mm thick PVC board with density not less 600kg per cum and top panel with 5.5 mm thick plain glass ficed with snap beading rubber of suitable size and each shutter n.exc 0.95 m in width complete all as specified and directed by the Engr-in-charge. |
| 50 | Supply and fixing ofpowder coated aluminum partition using 95.6mmx44.8mm x1.6mm frame work with 12mm thick PVC board with density not less 600kg per cum /5.5mm thick frosted glass including aluminum beading for fixing board each panel n.exc 1.20 Sqm complete all as specified and directed by the Engr-in-charge. |
| 51 | Plaster of Paris ceiling ( Gypsum anhydrous) including sunk or raised molding or coving, design, pattern as decided by Engr-in-Charge fixed in galvanized grid work including GI suspenders as per manufacture instructionand joints of ceilingboard shall befinished with textile tape etc complete all as specified and directed by the Engr-in-charge. |
| 52 | Preparation of POP false ceilingsurfacesof anydescription over10 cmgirth or width and applying two coats of plastic emulsion paintof approved tint over a coat of primer complete all as specified and directed by the Engr-in-charge. |
| 53 | Supplying and fixingin repair Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling the existing sheetscomplete all as specified and directed by Engineer-in-Charge |
| 54 | Rendering or plastering work 10mm thick in cement mortar 1:3 in facia or edging of Chajjas, ceiling and roof projections etc, including taking out pealed off plaster / concrete and making the line in true shape and finishing the surface without using extra cementetccomplete all as specified and directed by Engr-in-charge. |
| 55 | Factory made precast cement concrete coloured interlocking tiles 60 mm thick of size and shape directed strength not less than M-35 concrete laid and jointed in, on and including clean sand bed of 40mm thicknessincluding demolishing the existing surface complete all as specified and directed by Engr-in-charge |
| 56 | Demolition of cement concrete (un-reinforced) in above ground floors and pavings n. exc. 15cm thickness (below or above ground level) complete and all as specified and as directed by Engr-in-charge. |
| 57 | Demolition of brick work stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed by Engr-in-Charge. |
| 58 | Rendering 15mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:6) finished even and fair without using extra cement including two coats of OBD of any tint over a coat of white wash complete all as specified and directed by Engr-in-Charge. |
| 59 | Vitrifiedceramic lightshade tiles 10 mm thick (square or rectangular) polishedarea of each tileexe 0.36 Sqmbut n exc 0.42laid in floors, set and jointed with neat cement slurryincluding pointing in white cement with pigment to match the shade of tiles, complete all as specified & as directed by Engineer-in-charge. |
| 60 | Demolition ofreinforced concretein ground floors and paving n exc 15 cm thickness (below or above ground floors )complete all as specified and directed by Engineer-in-Charge |
| 61 | PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in cills,steps,plinth courses,copingetc, complete all as specified and directed by Engineer-in-Charge |
| 62 | Supply and fixing offloor door stopper of aluminiumalloy body and tongue 140 mm anodised with hard drawn steel spring fixed in door complete all as specified and directed by Engineer-in-Charge |
| 63 | Supply and fixingin repair aluminium die cast body Door closer hydraulically regulated design No1 universal type suitable for door shutterISI Markedcomplete all as specified and directed by Engineer-in-Charge |
| 64 | Supply and fixing ofMild steel screw bolts (machine made) 16mm dia of shank with hexagonal or square heads at one end and screwed the other, each screw end to be fitted with washers and one hexagonal or square nut exc 22.5cm but n exc 30cm long complete all as specified and directed by Engineer-in-Charge |
| 65 | Supply and fixing of plates (plain or chequered ) channels , square cut or notched(ordinaryand counter sunk) forming holeswithout anyattachmentcomplete all as specified and directed by Engineer-in-Charge |
| 66 | Supply and fixing offramed work such as grills , gratings etc with endsof bars shoulders and / or riveted or forged into spikes framed guard bars , barred iron doors ladders framed balusters walk ways railings frame work of water tank and similar workconfirming to fe 290 gde - E-165 complete all as specified and directed by Engineer-in-Charge |
| 67 | Preparation of new or priveously untreaterdsteel surfacesof any descriptionover 10cm width or girth, not otherwise desccribed applying two coats of synthetic enamel paint over a coat of redoxide complete all as specified and directed by Engineer-in-Charge |
| 68 | Material and labourfor point wiring with two single core 1.5 sqmm cable (nominal area) stranded copper conductor, PVC insulated unsheathed cable, 1100 V grade in and including concealed PVC conduit of size not less than 20mm dia with sunken type pressed steel terninal box 1.6 mm thick of suitable size, duly painted with one coat of red oxide primer andtwo coats of black bituminous paint for mounting fittings/ junction boxes and wiring to be terminated in pressed steel sunken boxes including all accessories and using single core 1.5 Sqmm (nominal area) stranded copper conductor, PVC insulated unsheathed cable as in earth wire (green colour) connected to common earth dolly complete all as specified and directed for following :- (a) One light point controlled by one switch. |
| 69 | (b) One fan/Exhaust fanpoint controlled by one switch and one regulator. |
| 70 | (c) One 3 pin switch socket outlet point 5 Amps on independent board. |
| 71 | (d) One 3 pin switch socket outlet point 5 Amps on same board with other switch. |
| 72 | All as per item No 68.00 abovebut with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size complete all as specified and directed by Engineer-in-Charge |
| 73 | Switch piano flushtype single pole, one way 5 Amps 230 Volts AC circuit complete all as specified & directed by Engr-in-Charge. |
| 74 | Supply and fixing switch piano flush type,15 Amps, Single pole, two way complete all as specified and directed by Engineer-in-Charge |
| 75 | Socket outlet 5 Amps, 5 Pin flush type multipurpose, 230 Volts AC circuit complete all as specified and directed by Engr-in-Charge. |
| 76 | Socket outlet 2 in 1, 3 Pin 5 & 15 Amps, 230 Volts AC circuit complete all as specified and directed by Engr-in-Charge. |
| 77 | Switch piano flush type single pole, one way 15 Amps 230 Volts AC circuit complete all as specified & directed by Engr-in-Charge. |
| 78 | Ceiling rose surface backlite 65x50mm 3 terminals complete all as specified and directed by Engr-in-Charge. |
| 79 | Supply and fixing of stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed by Engr-in-Charge. |
| 80 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rosecomplete all as specified and directed by Engr-in-Charge. |
| 81 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge |
| 82 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. minimum air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified & directed by Engr-in-Charge. |
| 83 | Supply and fixing factory made epoxy powder coated distribution board double door TPN 4 ways vertical type MCB DB, with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, strandard DIN rail, earth bar and cable ties for cable management complete all as specified and directed by Engineer-in-Charge |
| 84 | Supply and fixing factory made epoxy powder coated distribution board SPN 8 ways double door with acrylic top cover (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, strandard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts complete all as specified and directed by Engr-in-Charge. |
| 85 | Supply and fixing MCB single pole 240 volt C curve 10 KA 5 to 32 Amps capacity including taking down old one complete all as specified and directed by Engr-in-Charge. |
| 86 | Supply and fixing MCB single pole & neutral 240 volt \"C\" curve 10 KA 40Amps complete all as specified & directed by Engr-in-Charge. |
| 87 | Supply and fixing MCB TPN415 Volt C curve 10 KA 40 to 100 Amps capacityincluding taking down old one complete all as specified and directed by Engr-in-Charge. |
| 88 | Concealed sub main wiring using two single core PVC insulated, unseathed stranded copper conductor cable of size 6.0 Sqmm of voltage rarting upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 25mm with all fittings and accessories, along with one run of PVC (green colour) insulated, unsheathed, stranded copper conductor of size 4.0 Sqmm (green colour) as earth continuity conductor complete all as specified and directed by Engr-in-Charge. (Note : Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit) |
| 89 | Sub main wiring complete with 2 runs of 4 Sqmm single core PVC insulated unsheathed cable 1100 V,FR grade with multistranded copper conductor ISI marked drawn through PVC rigid conduit andaccessories fixed on surface/wall celing etc including provision of 1 run of 2.5 Sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity complete all as specified and directed by Engr-in-Charge. Note : Two runs of copper conducterand one runs of earth copper conductershall be measured as one length. |
| 90 | Supply and fixingsingle pole and neutral sheet metal enclosure with a two pin and earth plug and socket (Metal clad) 20 Amps complete with one single pole MCB 20 Amps capacity including taking down old one complete all as specified & directed by Engr-in-Charge. |
| 91 | Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality of capacity 1 TRincluding provision of 45 X 45 X 5 mm angle frame work for mounting of out door unit complete all as specified and directed by Engineer-in-Charge |
| 92 | Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity3 KVA complete all as specified and directed by Engr-in-Charge. |
| 93 | Supply and fixing single pointed air termination aluminium rod,12 mm dia, 300 mm long, mount vertically on top of GI pipe with provisioning of suitable insulating materials etccomplete all as specified and directed by Engr-in-Charge. |
| 94 | Supply , fixing and laying GI strip 32 mm x 6mm complete all as specified & directed by Engr-in-Charge. |
| 95 | Precast cement conerete block masonary (PCC) type B 1 (1:2:4) (20mm graded crushed stone aggregate) for support of spikes pipecomplete all as specified and directed by Engr-in-Charge. |
| 96 | M & L tubing (light grade) galavanised iron to be embedded in PCC block complete of size 40 mm bore complete all as specified and directed by Engr-in-Charge. |
| 97 | Test point terminal block made of gun metal or phorphous bronze of size 75x75x25mm drilled and screwed incl 3 Nos x 8mm dia 25 mm long hexagonal head screws complete all as shown on drgcomplete all as specified and directed by Engr-in-Charge. |
| 98 | Earthing complete with galvanised steel plate electrode 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25 Mtr deep below ground level) with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steelearth wire protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with6mm dia M.S. round bar placed 75mm c/c and handle of 10mm dia, MS bar made to shape, GI medium grade 20 mm bore pipe for watering perforated at bottom, 1.75 meter long placed on top edge of earth plate, common salt & charcoal filling, funnel, wire mesh and earth work not exceeding 50 meters all as per electrical plate No 3 of SSR Part I (2009) and connected toearth test pointsincluding testing on completion. complete all as specified and directed by Engr-in-Charge. |
| 99 | Earthingcompletewith galvanisedsteelearthplateelectrode 600x600x6mm burrieddirectlyin groundnotless than2.25mtr deepbelow normal ground level with top edgeof earth plate not less than 1.5mtrbelow normal ground level connected to the Galvanised iron strip 32x6mm sizeby meansof welding,bolts ,nuts,check nutsandwashersof galvanisediron and 32x6mm GI strip procted by provision of GI light grade pipe 40 mm boreincluding provision of concrete pit in PCC1:2:4 typeB-I, using 20 mm graded crushed stone aggregates with 40 mm thick cover of RCC (1:2:4) reinforced with XPMweight not less than 4 Kg /Sqm and 6mm diabar handle ,excavationand earthworkin any type of soil ,charcoaldustand saltlightgrade GI watering pipe 20 mm bore with funnel and wire mashand medium grade GIprotectionpipe 15mm bore 5 Mtr long and GI strip upto main earthingof polecomplete all as shown in electrical plateNo 3 of MES Sch 2009 Part-I complete all as specified and directed by Engr-in-Charge. |
| 100 | Supply , laying, commissioning and testing in replacement of old unservicable, laid in trenches/ducts or passing through pipe ,1100 volt gradeLT undergroung cable with XLPE insulated armored heavy duty electric cable with strandedaluminium conductor 1100V grade 3.5 core cross sectional area 50 sqmm laid in trenchs or passing through pipe including necessary excavation, sand, bricks etccomplete all as specified & directed by Engr-in-Charge. |
| 101 | Material and labour for dry river bed sand filling in trenches for cable cushioning below and abovethe cable complete all as specified and directed by Engr-in-Charge. |
| 102 | Supply and laying unreinforced pre cast concrete flat cable cover, class LV, Type 1 flat, size 250 x 150 x 40mm complete all as specified and directed by Engr-in-Charge. |
| 103 | Material and labour for cutting of bituminous road / floor for laying of pipe / cables not exceeding 1.5 meter wide and not exceeding 1.5meterdeep including refilling / with material and, watering well ramming / compacting and making good with PCC 1;2;4,type B-1, 100mm thick complete all as specified anddirected by Engr-in-Charge.Note :-PCCshall bemeasuredseparately. |
| 104 | Material & labour for tubing GI pipe light grade, forroad crossing / on wall / on pole for cableprotection of size50 mm bore complete all as specified and directed by Engineer-in-Charge. |
| 105 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-Charge. |
| 106 | Taking down sub main wiring complete including fitting and fixtures, removing materials to store or keeping in safe custody and making good the disturbed surfaces of walls, floors, roof etc., complete all as specified anddirected by Engr-in-Charge. |
| 107 | Taking down carefully unserviceable DB any type/size disconnecting and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge. |
| 108 | Taking down carefully unserviceable MCB SP/SPN/Isolator of any rating/size complete all as specified and directed by Engineer-in-Charge. |
| 109 | Point wiring complete with 1.5 sqmm single core PVC insulated FRLS andunsheathed cable 1100 volts grade with multistranded copper conductor drawn through concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, includingmetal flush box fabricated steel terminal box MS sheet concealed in walls, with modular white cover plate with frame and for housing the switches, socket outlets, fan regulators with rigid non metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts,saddles, pipe hooks etc. of 20 mm dia, junction box 1 to 4 way suitable for 25mm dia conduit etc., all as specified and as directed for the following: -(a) One light point controlled by one switch. |
| 110 | (b) One fan/Exhaust fanpoint controlled by one switch and one regulatorcomplete all as specified and directed by Engr-in-Charge. |
| 111 | (c) One bell point controlled by one 6 Amps bell pushcomplete all as specified anddirected by Engr-in-Charge. |
| 112 | (d) One 3 pin switch socket outlet point 5 Amps on independent board complete all as specified and directed by Engineer-in-Charge. |
| 113 | (e) One 3 pin switch socket outlet point 5 Amps on same board with other switch complete all as specified and directed by Engineer-in-Charge. |
| 114 | All as per item items No 106.00 above but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm sizecomplete all as specified and directed by Engr-in-Charge. |
| 115 | Supply and fixing ofmodular switch one way 6A, 1 module complete all as specified anddirected by Engr-in-Charge. |
| 116 | Supply and fixing ofmodular switch one way 16A, 1 module complete all as specified and directed by Engineer-in-Charge. |
| 117 | Supply and fixing ofsocketout let 6A 2/3 on combined 2 module complete all as specified and directed by Engineer-in-Charge. |
| 118 | Supply and fixing ofsocket out let 6A/16A-2/3 pin combined 2 module complete all as specified anddirected by Engr-in-Charge. |
| 119 | M&L forbell push 6 Amps 230 V, AC circuitcomplete all as specified and directed by Engineer-in-Charge. |
| 120 | M&L for call bell ding dong 230 V AC circuit complete all as specified and directed by Engr-in-Charge. |
| 121 | M&L for Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed by Engineer-in-Charge. |
| 122 | Supply and fixing of fan regulator electronic 2 modular type volts AC 50 HZ ,300 Watts,4 step complete all as specified and directed by Engineer-in-Charge. |
| 123 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified anddirected by Engr-in-Charge. |
| 124 | Supply and fixing factory made epoxy powder coated distribution board SPN 12 ways double door with acrylic top cover (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, strandard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockoutscomplete all as specified and directed by Engineer-in-Charge. |
| 125 | Supply and fixing PVC conduit of size 40 mmrun in wall / surface for existing telephone cable / Lan cable complete all as specified and directed by Engr-in-Charge. |
| 126 | Supply and fixing PVC conduit of size 25 mmrun in wall / surface for existing telephone cable / Lan cable complete all as specified and directed by Engr-in-Charge. |
| 127 | Taking down the defective ceiling fan of any sweep andmake after disconnecting electrically & mechanically and transporting to the work shop dismantling, examine & carry out the repairs as required and brought back to site, re-fixing, testing in all respect for smooth running and comprising of the following:-(a)Servicing/overhauling the ceiling fan by thoroughly cleaning the bearing, shaft, stator, rotor & applying the lubricant / grease to the bearing including applying one coat of super enameled varnish over the winding to improve the insulation value complete all as specified and directed by Engr-in-Charge. |
| 128 | Supply and fixing of exhaust fan made of sturdy Engineering plastic complete with louvers shutters , 300 mm sweep, single phase, 230 Volts AC,1200 RPM,, ISI marked fixed properly at directed location with provisioning of suitable fixing/tightening arrangements and connecting/testing complete all as specified and directed by Engr-in-Charge. |
| 129 | Supply and fixing exhaust fan steel body , 380 mm sweep, with blades and frame and louvers.,single phase, 230 Volts AC,with provisioning of suitable fixing/tightening arrangements and connecting/testing complete all as specified and directed by Engr-in-Charge. |
| 130 | Supply and fixing of LED street light fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge. |
| 131 | Supply and fixing of electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed by Engineer-in-Charge |
