|
| 1 | Engaging Earth excavator 75 H.P. for removal ofslips in all kinds of soils, levelling and dressing of sides and disposal of same outside theperiphery of the areacleared by engaging of tractor trollywherever required ( all inclusive including POL) as per thedirections of the Engineer-in - Charge. |
| 2 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix) |
| 3 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms , incl. disposal or filling of excavated earth wherever requiredas per the directions of Engineer-in-charge . |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)incl. all leads, lifts & carriage of material by MT/ H.L. |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L. |
| 6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including all leads, lifts & carriage of material by MT / H.L. |
| 7 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5coarse sand :3graded stone agg. 20 mm nominal size)incl. all leads, lifts & carriage of material byMT/ H.L. |
| 8 | Providing and laying Reinforced Cement Concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircase having upto 15° slope. excluding cost of centering and shuttering , all work upto floor V levelincluding all leads, lifts and carriage of material byMT / H.L. |
| 9 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.1:1.5:3 (1 cement : 1.5coarse sand :3graded stone aggregate 20 mm nominal size ) incl. all leads, lifts & carriage of material byMT/ H.L. |
| 10 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto all level Thermo-Mechanically Treated bars of grade Fe-500D or more incl. all leads, lifts andcarriage of material by M.T. / H.L. |
| 11 | Brick work with F.P.S. bricks of class designation 75in foundation and plinthincluding all shapes,leads, lifts and carriage of material by MT / H.L. in cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 12 | Brick work with F.P.S. bricks of class designation 75in foundation and plinthincluding all shapes,leads, lifts and carriage of material by MT / H.L. in cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 13 | Extra for brick work in superstructure above plinth level upto floor V level (By manual means) incl. all leads, lifts & carriage of material by M.T. H.L. |
| 14 | Half brick masonrywith bricks of class designation 75 in foundations and plinth in cementmortar 1:4 ( 1 cement :4coarse sand)incl all leads, lifts and carriage of material by MT / H.L. |
| 15 | Extra for brick work in Square or rectangular pillarsincl all leads, lifts and carriage of material by MT / H.L. |
| 16 | Providing and laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1cement:2 coarse sand: 4 graded stone aggregate 12.5 mm nominal size) and curing complete incl. all leads, lifts & carriage of material by MT/ H.L. |
| 17 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.50 mm thick with 20mm nominal size stone aggregate |
| 18 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.40mm thick with 20 mm nominal size stone aggregate. |
| 19 | 6 mm thick plasterto ceiling of mix 1 : 3 ( 1 cement : 3 fine sand) incl. all leads, lifts and carriage of material by M.T / H.L. |
| 20 | 12 mm cement plaster of mix 1 : 4 ( 1 cement : 4 fine sand) including all leads, lifts and carriage of material by M.T / H.L. |
| 21 | 15mm cement plaster on rough side of single orhalf brick wall of mix 1:4 (1 cement: 4 fine sand) incl. all leads, lifts & carriage of material by M.T / H.L. |
| 22 | Providing and fixing strips in joints of terrazzo/ cement concrete floors. Glass strips 40 mm wide and 4 mm thick |
| 23 | Centring and shuttering including strutting propping etc and removal of form work for:- |
| 24 | Foundations, footings, bases of columns etc. for mass concrete |
| 25 | Suspended floors, roofs, landings, balconies and access platforms. |
| 26 | Lintels, beams, plinth beams, girders,bressumers and cantilevers |
| 27 | Edges of slabs and breaks in floors and wallsunder 20 cms wide. |
| 28 | Providing wood work in Sal woodframes of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately: |
| 29 | Providing and fixing 35mm thick glazed shutters ofSecond class deodar woodfor doors, windows and clerestory windows using10 kg/ sqm (4 mm thick) glass panes including black enameled ISI marked M.S. butt hinges with necessary screws. |
| 30 | Providing and fixing 35 mm thickWire Gauze shutters using galvanised M.S. wire gauge of average width for aperture 1.4 mm in both direction with wire of dia. 0.63 mm for doors, windows & clerestory windows with hinges & necessary screws. ISI marked M.S. pressed bright finished butt hinges with necessary screws of req. size. Second Class deodar wood. |
| 31 | Providing and fixing 35 mm thickpanelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excl. panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second class deodar wood |
| 32 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Particle Board 12mm thickPlain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS : 3087 marked |
| 33 | Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc. |
| 34 | Providing and fixing aluminum sliding door bolts 300x16 mm ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete |
| 35 | Providing and fixing aluminum hanging floor door stopper, ISI marked,anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. completeTwin rubber stopper |
| 36 | Providing and fixing aluminium handles 125 mmISI marked anodised (anodic coating not less thangrade AC10 as per IS:1868) transparent or dyedto required colour or shade with necessary screws etc complete |
| 37 | Providing and fixing aluminum tower bolts ISI marked anodized (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed torequired colour or shade with necessary screws etc. complete : |
| 38 | 150x10 mm |
| 39 | 200x10 mm |
| 40 | Providing and fixing bright finished brass hard drawn hooks and eyes 100 mm |
| 41 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.Internal work-exposed on wall, including fixing the pipe with clamps at 1.00 meter spacing |
| 42 | 15mm nominal outer dia pipes. |
| 43 | 20mm nominal outer dia pipes. |
| 44 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 45 | Providing and Fixing CPVC Union |
| 46 | Providing and fixing ball valve (brass) of approved quality, High or lowpressure, with plastic floats complete15 mm nominal bore |
| 47 | Providing and Fixing Tee |
| 48 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover & suitable locking arrangementofFinolex, Sintex or Vectus or equivalent make and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank ( Make - Sintex or as per approved local Manufacturer ) |
| 49 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1cement :4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) including necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design.With common burnt clay (non modular) bricks of class designation 7.5 |
| 50 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 51 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.( Make - Jaquar CNS - WHT - 453) |
| 52 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. ( Make - Jaquar FLS - WHT -5301) |
| 53 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, includingpainting of fittings and brackets, cutting and making good the wallswherever required . Kitchen sink without drain board610x510mm bowl depth 200mm |
| 54 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete. Semi rigid pipe 40 mm dia |
| 55 | Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 56 | Providing and fixing 600 x 450 beveled edge mirror of superior glass (ofapproved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 57 | Providing and fixing toilet paper holder C.P. brass |
| 58 | Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete |
| 59 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 |
| 60 | Providing & fixing 15mm nominal bore C.P. brass angle valve for basin mixer and gyser points of approved for conforming to IS : 8931 |
| 61 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms (.Make - Jaquar ACN1121 N ) |
| 62 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 18.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 63 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms |
| 64 | Making plinth protection 50 mm thick of cement concrete 1:3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed & consolidated & grouted with fine sand including finishing the top smooth. Crushed aggregate including all leads, lifts and carriage of material by MT/H.L. |
| 65 | 10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35kg per cum of earth and gobri leaping with mix 1:1 (1 clay: 1 cow dung) and covered with specified tile bricks grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finishing neat.With common burnt clay (non modular) brick tiles of class designation 10.0 |
| 66 | Painting top of roofs with bitumen of approved quality at 17 kg per 10sqm impregnated with a cost of coarse sand at 60 cudm per 10 sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete. with residual type petroleum bitumen of grade VG-10 |
| 67 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase. |
| 68 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet completeincl. all leads, lifts & carriage of material by MT/ H.L. |
| 69 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angles 40x40x6mm for diagonal braces |
| 70 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.Ilimpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 71 | Providing and fixing powder coated sheet of approved qualityfor roofing including nails,screws,washers etc. |
| 72 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diametre |
| 73 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion Bend 87.5°110 mm bend |
| 74 | Providing and fixing un-plasticised -PVC pipe clips of approved design toun-plasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm |
| 75 | Structural steel work inRiveted and boltedbuilt up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete. |
| 76 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 77 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) |
| 78 | Colour washing such as green blue or buff to give an even shadeNew work (two or more coats) with a basecoat of white washing with lime. |
| 79 | White washing with lime to give an even shade on New Work (three or more coats) |
| 80 | Painting with black anti-corrosive bitumastic paint of approved brand andmanufacture to give an even shade on new work Two or more coats. |
| 81 | Providing and fixing powder coated sheet of approved qualityfor making shed including nails,screws,washers etc. |
| 82 | Steel work welded in built up sections/framed work, incl. cutting,hoisting, fixing in position & applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates & similar works. |
| 83 | Providing and applying White Cement based Putty of average thickness 2 mmof approved brand & manufacture, overtheplastered wall surface to prepare thesurface even & smooth complete. |
| 84 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 85 | Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 86 | Applying priming coat with ready mixed red oxide Zinc Chromate primer ofapproved brand and manufacture on steel work (second coat) |
| 87 | Painting on G.S sheets with synthetic enamel paint of approved band & manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. |
| 88 | Wiring for light point/ fan poiint/exhaust fan point/ call bell point with1.5 sq.mm FRLS PVC insulatedcopper conductor singlecorecable in surface/rececessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 89 | Supplying and fixing of following electrical itemssuitable for operating on 240/230Volts AC, 50 Hz supply. Ceiling fan 1200 mm sweep along-with rod up-to 2\"-6\" long as required. |
| 90 | Supplying of following LED fixtures. 20/22 watt LED 4 feet tube light fitting/fixture CRCA housing with 2000 Lumens and min lumens efficiency100 Lumens/watt P.F 70.95 THD < 16% & voltage input range 140-270 V with Shot circuit & overloading protection circuit off |
| 91 | Supplying and fixing offollowing modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 92 | Bell Bush |
| 93 | 15/16 amp switch |
| 94 | 3 pin 5/6 amp socket outlet |
| 95 | 6 pin 15/16 ampsocket outlet |
| 96 | Supplying and fixing of Stepped type 2 module electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 97 | Supplying and Fixing of followingelectrical fittings for conduit pipes |
| 98 | Fan Box |
| 99 | Deep Box |
| 100 | MCB SPN 63 Amp |
| 101 | Holder |
| 102 | Supply and fixing of Ceiling fan 1200 mm sweep along with 1-6// long fan rod |
| 103 | Supplyand fixingh exhaust fan 300 mm sizemetalic |
