|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - a) All work upto plinth level: ii) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 2 | Centering shuttering including struttings, proppingetc. and removal of form work forFoundations, footings, bases for columns |
| 3 | Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., includingcutting, hoisting, fixing in position and applying apriming coat of approved steel primer, including weldingand bolted with special shaped washers etc. complete Hot finished welded type tubes |
| 4 | Providing and fixing MS bolts including nuts and washers complete as per standard designUpto 300mm length for fixingbase plates, 12mm dia, |
| 5 | Providing and laying ceramic floor tiles in different sizes(thickness to be specified by the manufacturer) of 1stquality conforming to IS : 15622 - 2017 of approvedmake in colours such as White, Ivory, Grey, Fume RedBrown, laid over 20 mm thick cement mortar 1:4 (1cement : 4 fine sand), Jointing with grey cement slurry @3.3 kg/sqm including pointing the joints with whitecement and matching pigment etc. completeAnti-Skid TilesCeramic Tiles 1st quality 300 x 300mm in all shades and designs |
| 6 | Providing and fixing rectified glazed wall tiles 300 x 450mm or more conforming to IS : 15622 - 2017 ( thicknessto be specified by the manufacturer ) of approved makein all colours, shades of any size as approved byEngineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cementslurry including pointing with white cement mixed withpigment of matching shade complete |
| 7 | Supply & installation of pre-painted Galvalume sheetsfor roofing/cladding (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) in550mpa steel grade, made out of Cold Rolled Steelcoated with Zinc-Aluminium alloy coating of 43.5% Zn,55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70,colour coated with high quality Polyester coating, topcoated of modified polyester of 20 micron, back sidecoat of 5 micron, having epoxy primer coat of 5 micronon both side. Sheet should have protective guard filmof 25 microns minimum to avoid scratches whiletransportation and should be supplied in singlelength upto 12 metre or as desired by Engineer-incharge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x 55mm) with EPDMwashers filled with white lead complete upto anypitch in horizontal/ vertical or curved surfacesexcluding the cost of purlins, rafters and trusses andincluding cutting to size and shape wherever required0.50mm thickness |
| 8 | Supply & installation of pre-painted Galvalume sheetsroofing accessories in 550mpa steel steel grade, madeout of Cold rolled steel coated with Zinc-Aluminiumalloy coating of 43.5% Zn, 55% Al and 1.5% Siliconconfirming to AASTM A792/A792M and AS1397, Alloycoating AZ150/AZ70, colour coated with high qualitypolyester coating, top coated of modified polyester of20 micron, back side coat of 5 micron, having epoxyprimer coat of 5 micron on both side. Sheet should haveprotective guard film of 25 microns minimum toavoid scratches while transportation. Sheet shouldhave protective guard film of 25 microns minimumto avoid scratches while transportation. The sheetshall be fixed using self drilling /self tapping screwswith EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm0.50mm thickness |
| 9 | Providing and fixing on wall face unplasticisedRigid PVC rain water pipes (working pressure 4kg/cm2) conforming to IS : 13592 Type A includingjointing with seal ring conforming to IS : 5382leaving 10 mm gap for thermal expansion:Single socketed pipe - 110 mm OD |
| 10 | Providing and fixing on wall face unplasticised - PVCmoulded fittings/ accessories for unplasticised RigidPVC rain water pipes conforming to IS : 13592 Type-Aincluding jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:Bend 87.5°/110mm |
| 11 | 12 mm cement plaster of mix Cement mortar 1:4 (1 cement : 4 fine sand) |
| 12 | Neat cement punning |
| 13 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: |
| 14 | Dismantling tile work in floors and roofs laid incement mortar including stacking material within 50metres lead For thickness of tiles 10 mm to 25 mm |
| 15 | Dismantling old plaster or pointing, raking outjoints, cleaning and preparing the surface for replastering or re-pointing including disposal ofrubbish to the dumping ground with all leads andlifts etc.complete as per direction of the Engineer- incharge. |
