|
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm. |
| 2 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation. |
| 3 | With earth obtained by fresh excavation (including cost of excavation upto 1,800 mm. depth) from land arranged by the Deptt. within a lead of 100 m. |
| 4 | Filling in foundation or plinth silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 5 | Furnishing and laying of the live sods of perennial turf forming grass on embankment slope, verges or other locations shown on the drawing or as directed by the Engineer including preparation of ground, fetching of sods and watering as per Clause 307 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). |
| 6 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 7 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 8 | Anti termite treatment to bottom surface ( in case of masonry foundation and basements) and the sides (upto a height of 300 mm. from bottom) of the excavation trenches with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. area. The work shall be carried out as per specification described in 6.2.1. of code IS- 6313 (part -II) 1981. (Mode of measurment will be the plan area of foundation treated.) |
| 9 | Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor (a) 1:3:6 proportion |
| 10 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in 2nd Floor as per relevant IS codes. (i) Pakur Variety |
| 11 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(a) 25 mm to 30 mm thick wooden shuttering asper decision & direction of Engineer-In-Charge. |
| 12 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation, basement and upto roof of ground floor(i) Tor steel/Mild Steel, JSW/JSPL/SHYAM/SRMB/BMSL/ELECTROSTEEL1st Floor. |
| 13 | Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth |
| 14 | In Super Structure ground floor. |
| 15 | 125 mm. thick brick work with 1st class bricks in cementmortar (1:4) in ground floor. |
| 16 | 75 mm. thick brick work with 1st class bricks set in cement, sand mortar (1:4) in ground floor including H.B. netting in every alternate layers. |
| 17 | 25mm. thick damp proof course with cement concrete with stone chips (1:2:4) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer\"s specification followed by two coat of polymer based paint,double chequired complete as directed(cost of water proofing compound & polymer based paint to be paid separately) |
| 18 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,caffolding/staging where necessary (1st floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (b) 20 mm thick plaster |
| 19 | 15mm thick plaster External wall |
| 20 | 1:4 Plaster 10 mm thick |
| 21 | Labour for Chipping of concrete surface before taking upPlastering work. |
| 22 | Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer\"s specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contrr]e) I(I) With application slurry @1.75 kg/ Sq.m, 20 mm sandcement mortar (1:4) & 2 mm thick cement slurry at back sideof tiles, 0.2 kg/ Sq.m white cement for joint filling withpigment.Light Colour |
| 23 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. |
| 24 | Wood work in door and window frame fitted and fixed inposition complete including a protective coat of painting at thecontact surface of the frame exluding cost of concrete, IronButt Hinges and M.S clamps. (The quantum should be corretedupto three decimals).(b) Sal: Malaysian |
| 25 | Panel shutters of door and window, as per design (each panelconsisting of single plank without joint), including fitting andfixing the same in position but excluding the cost of hinge andother fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) 35 mm thk shutters 19 mm thk panel of size 30 to 45 cm, (Sishu,Gamar,Champ,Badam,Bhola,Mogra,Hallak) |
| 26 | Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm Prelaminated PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer?s specification and direction of Engineer-in-Charge. |
| 27 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel usingPVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge.In ground floor. |
| 28 | M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc.fitted and fixed with necessary screws and lugs in ground floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. |
| 29 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) (a) 40mm X 6mm, 200mm Length |
| 30 | Iron butt hinges of approved quality fitted and fixed with steelscrews, with ISI mark.(vii) 100mm. X 75 mm. X 3.5 mm. |
| 31 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: 300mm long x 10mm dia. bolt. |
| 32 | Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete.300mm x 16mm dia. bolt. |
| 33 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:(a) With continuous plate base (Hexagonal/ Round rod)150 mm grip x 10 mm dia rod. |
| 34 | 125mm long wooden buffer block With Sal : Malayasian |
| 35 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete.UPVC pipes 110 mm dia |
| 36 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers |
| 37 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 38 | Priming one coat on metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 39 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. onthe surface, if necessary :(a) On timber or plastered surface : With super gloss (hi-gloss) -(iii) Two coat (with any shade except white) |
| 40 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. onthe surface, if necessary :(a) On metal surface : With super gloss (hi-gloss) -(iii) Two coat (with any shade except white) |
| 41 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. (In Ground Floor)(a) One Coat Solvent based interior grade Acrylic Primer |
| 42 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning and smoothning of surface.Two Coats |
| 43 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.One Coat |
| 44 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.In Ground floor (Two Coat)a) Normal Acrylic Emulsion |
| 45 | Galvanised Iron pipe outlet for water with bevelled end at outlet, supplied fitted and fixed complete including painting two coats to the exposed portion.40 mm. Dia. |
| 46 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor)(i) In Roof:-With 0.63 mm thick sheet |
| 47 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavationearth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. (i) For 10 usersA) With Pakur variety. (SAIL/TATA/RINL) |
| 48 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer(a) 500 litre capacity |
| 49 | Labour for hoisting plastic water storage tank. (i) Upto 1500 litre capacity. (a) Upto 1st story from G.L. |
| 50 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 51 | Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO /ATLAS or equivalent) 15 mm |
| 52 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessaryccessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work PVC Pipes (Dia) 15 mm |
| 53 | 25mm |
| 54 | 32 mm |
| 55 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing).530 mm X 410 mm |
| 56 | Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S. 3989/ 2009 and I.S. 1729/2002 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete.Measurement will be made along the center line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately). (a) With valamoid joints including sealing with sand cement morter (4:1) upto quarter depth.100 mm dia. (internal) |
| 57 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 58 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.550 mm X 400 mm size |
| 59 | Supplying, fitting and fixing chech valve (vertical) G.M. tested to 21 kg per sq. cm.40 mm |
| 60 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).40 mm dia |
| 61 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoilsafter work complete in all respect with all costs of labour and materials.With Pakur variety. (SAIL/TATA/RINL) |
| 62 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour andmaterials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia. (SAIL/TATA/RINL) |
| 63 | Tube Well Labour for boring tube well of required dia. by water jet system through any type of soil strata including hire and labour charges for boring pipes, scaffolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other incidental works in the connection. The tube well should have a minimum 50 mm gap in between the outside of the tubewell pipe and the bore. (a) For depth upto 150 metre.(i) 40 mm dia. boring etc. |
| 64 | Supply of G. I. pipes of TATA make including necessary sockets40 mm dia.Medium quality |
| 65 | Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I).40 mm |
| 66 | Supplying PVC strainer of approved make with adapter conforming to I.S.12818 specifications.(i) 40 mm dia. |
| 67 | Supplying, fitting and fixing plug of approved make conforming to I.S. specifications.(i) 40 mm |
| 68 | Supplying, fitting and fixing steel cutter piece upto 450 mm long with sockets.(i) 40 mm dia. |
| 69 | Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction. |
| 70 | Supplying, fitting and fixing popular Maya pump no-6 or similar.(i) For 40 mm dia. tube well |
| 71 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm. |
| 72 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 73 | Cement concrete with graded stone ballast (26 mm size excluding shuttering) |
| 74 | 125 mm. thick brick work with 1st class bricks in cementmortar (1:4) in ground floor. |
| 75 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,caffolding/staging where necessary (1st floor).[Excluding cost of chipping over concrete surface](b) 15 mm thick plaster |
| 76 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. |
| 77 | ElectricalDistribution wiring in 2 x 22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire(Brand approved by EIC) in 20mm size PVC rigid conduit \"FR\"(Precision make), with 1x22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire forECC, to light/fan/call bell points with Modular type switch(Brand approved by EIC) fixed on Modular GI switch boardwith top cover plate and 2 no. suitable size “Ph & N” copperbar & earthing attachment fixed on wall incl. mending gooddamages to original finish. Average run 9 mtr |
| 78 | Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire(Brand approved by EIC) in 20mm size PVC rigid conduit \"FR\"(Precision make), with 1x22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire forECC, to light/fan/call bell points with Modular type switch(Brand approved by EIC) fixed on Modular GI switch boardwith top cover plate and 2 no. suitable size “Ph & N” copperbar & earthing attachment fixed on wall incl. mending gooddamages to original finish. On board 2 x 22/0.3 (ph & N) and 1 x 22/0.3 as ECC |
| 79 | Average run 7.5 mtr |
| 80 | Supply & Fixing 240 V 6 A Modular type switch (Brand approved by EIC) on existing GI Modular type switch board having top cover plate and making necessary connections as required |
| 81 | Supply & Fixing 240 V, 6A, 5 pin Modular type plug socket (Brand approved by EIC), without switch & plug top, on existing GI Modular type switch board with top cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 82 | Supplying & Fixing two plate ceiling rose on wooden single block on wall by screws etc. Make Anchor/Similar make |
| 83 | Supply & Fixing 240V, Modular Socket (2 Module) type fan regulator (Step type) (Brand approved by EIC) on existing Modular GI switch board with top cover plate incl. Making necy. connections etc. |
| 84 | Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire. |
| 85 | Supply and delivery 250V 50 Hz A.C. Ceiling fan complete with blade ,canopy fork, rubber,bush etc Make USHA/BAJAJ/Similar makeModel Nabila 5 star (Metalic) 1200 mm |
| 86 | Supplying and fixing 415V, TPN SFU with sheet steel enclosure on flat iron/angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.200A Make Siemens/L&T/Havells |
| 87 | Supplying and fixing 415V, TPN SFU with sheet steel enclosure on flat iron/angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.125A Make Siemens/L&T/Havells |
| 88 | Supplying and fixing 415V, TPN SFU with sheet steel enclosure on flat iron/angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.63A Make Siemens/L&T/Havells |
| 89 | Supplying and fixing 415V, TPN on load front operated Changeover switch with Sheet Steel enclosure on angle iron frame on wall with nuts bolts etc125A Make Havells/S.M |
| 90 | Supplying and fixing sheet metal (16 SWG) iron clat Cubusbar Chamber on angle iron frame on wall includingearthing attachment and painting as required. 4 bar 415 V 315 Amp.DimensIon of Copper bar 4x40x5 mm Dimension of sheet metal box 500x150 mm including amp meter, volt meter Indication lamp and selector switch |
| 91 | Supplying and fixing sheet metal (16 SWG) iron clat Cubusbar Chamber on angle iron frame on wall includingearthing attachment and painting as required (As perDrawing no. 470 of PWD Specification Book- may 1991)4 bar 415 V 200 Amp. 4x20x5 mm |
| 92 | Supplying and fixing earth busbar of galvanized (Hot Dip)MS flat 25 mm X6 mm on wall having clearance of 6 mmfrom wall including providing drilled holes on the busbarcomplete with GI bolts, nuts, washers, spacing insulatorsetc. as required. |
| 93 | Connecting the equipments to earth busbar incl. S & FG.I. (Hot Dip) wire on wall/ floor with staples buried insidewall/ floor as required and making connection to equipments with bolts, nuts, Washers, cable lugs etc. as required and manding good damages.b) 8 SWG |
| 94 | Supplying and laying 1.1 K.V. grade 4 core 16 sqmm PVC/A cable with earth continuty after cutting floor/ pavement/ wall and making holes including embedding the cable at an average depth 75 mm in floor/ wall/ pavement etc. and mending good the damage to original finish incl. removing the rubbish.Make: KEI /Havell\"s /Polycab /Gloster(a) 4 core 16 sq mm |
| 95 | Supplying and laying 1.1 K.V. grade 2 core 6 sqmm PVC/A cable with earth continuty after cutting floor/ pavement/ wall and making holes including embedding the cable at an average depth 75 mm in floor/ wall/pavement etc. and mending good the damage to original finish incl. removing the rubbish.Make: KEI /Havell\"s /Polycab /Giloster(a) 2 core 6 sq mm. |
| 96 | Supplying and fixing compression type gland completewith brass gland, brass ring & rubber ring for dust &moisture-proof entry of XLPE /PVC armoured cables as belows:4 core 16 sq mm |
| 97 | 2 core 6 sq mm |
| 98 | Finishing of the XLPE /PVO insulated armoured cable ends by soldering with cable sockets and insulated types etc. including supplying sockets, soldering materials,tapes etc. and making connection to switch, BDB and BBC etc.4 core 16 sq mm |
| 99 | 2 core 6 sq mm |
| 100 | Supplying and fixing double door TPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damagagento original finish incl. inter connection with size of copper wire and neutral link & provision for earthing attachment.Make: Legrand4 way Enclosure (607715) |
| 101 | Supplying and fixing double door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damagagento original finish incl. inter connection with size of copper wire and neutral link & provision for earthing attachment. Make: Legrand/ Siemens/ SM2+12 way Enclosure (607712) |
| 102 | Supplying & fixing 240/415 V MCB Isolator on din rail of existina BDs and necessary connection.Make: Legrand/ Siemens/ SM 40A D.P. Isolator |
| 103 | 63A D.P. Isolator |
| 104 | Supplying & fixing 240/415 V MCB of breaking capacity 10 KA & C characteristics on din rail of existing BDs and necessary connection.Make: Legrand/ Siemens/ SM 6-32A S.P MCB |
| 105 | Distribution wiring in 1.1kV single core stranded \"FR PVC insulated & unsheathed copper wire (apprd. make) in 20 mm size PVC rigid conduit \"FR\" (precision make) incl. necy. fittings as required 2x22/0.3 (1.5 sq mm) + 1x22/0.3 (1.5 sq mm) ECC For 5 Nos. computer, Av. Run 1O M. |
| 106 | Supplying & fixing 240 V 16A 3 pin Modular type plug socket (Brand approved by ECI) without plug top and switch, on existing GI modular type switch board with top cover plate and making necessary connection with PVC Cu wire and earth continuty wire etc. |
| 107 | Supplying and delivery 250 V, 4 ft. double/ single fluorescent tube light fittings incl. S & F 40 W tube/ LED tube complete with all accessories.Make: Havells/ Philipsa) Code No. LHFYBYFIPBIW028 with 1xT-5 28 W or Cat |
| 108 | Fixing only single/ twin fluorescent light fitting complete with all accessories directly on wall/ ceiling with HW block and suitable size MS fastener, Ceiling plate, nipples etc. as required. |
| 109 | Sub Total |
| 110 | GST 12% |
| 111 | CESS 1% |
