|
| 1 | Earth work in excavation in foundation trenches or drains including dressing of sides & ramming of bottoms, lift up to 1.5M incl. Taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50m all kinds of soil. |
| 2 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size). |
| 3 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation in basements rafts, footings, straps beams, bases of columns etc. up to plinth level. |
| 4 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix/ Design Mix |
| 5 | Random Rubble stone masonry for foundation and plinth in Cement sand mortar above 30 CM thick wall in : cement mortar 1:6 (1-cement : 6-sand). |
| 6 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead as per Technical Specification Clause 301.5 |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 8 | Brick masonry for superstructure upto third storey with bricks of class designation 75 in : cement mortar 1:6 (1 cement : 6 coarse sand). |
| 9 | Half brick masonry in foundation & plinth using bricks of designation 75 Cement mortar 1 : 4 (1 cement : 4 coarse sand) Add extra for half brick masonry in super structure upto third story including cost of norminal hoop reinforcement (2 Nos. ,6mm Ø M.S. bar at every fourth course) . |
| 10 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 11 | Plaster on new surface on walls in cement sand mortar 1:6 including raking of joints etc. complete fine finished :- 20 mm thick |
| 12 | P & F Vitrified Porcelain Polished tiles ( Naveen/ Euro make , size 600 mm x 600 mm and thickness 10mm) on floor, skirting and steps etc. laid with tile admixture (Roff Pidilite or equivalent) including filling of joints by water proofing tile grout (Fevimate, Roofie, Untile or equivalent) specially for adhesive with graded granuals, polymer and stable pigment fine finished including cleaning of joints etc. complete as per direction of Engineer Incharge. Conforming to IS 15622 of approved make in all colour and shade, |
| 13 | Marble stone flooring table rubbed, 18 mm thick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Makrana \"Adanga\". Above 3601 Cm2 Slabs |
| 14 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 15 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 16 | Providing and fixing of P.V.C. door frame made from extruded PVC Confirming to IS : 10151-1982 section having multi chamber cross section with a maximum wall thickness of 2.8mm ± 0.3 mm duly reinforced with steel tie rod at bottom, and weather seals complete : P.V.C. door frame section (53 x 60mm) |
| 17 | Providing and fixing of Plastic shutter Infill made from extruded multi chamber hollow P.V.C. section having cross section of 200 x 20 x 1mm and shutter frame made from extrude P.V.C. section in the configuration of double walled ‘C’ section having an overall cross section of 40 x 37 mm and door fittings such as hinges, aldrop. Handles, stopper, locking bolt will be provided. |
| 18 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. |
| 19 | Painting with enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 20 | Providing & fixing stainless steel railing with 75cm height from floor with 75mm OD main post where necessary with 40mm OD post with 90cm distance at stair with 50mm OD top railing pipe with fitting in all respect. As per direction of engineer in charge. |
| 21 | Supply and fixing in cement mortar welded hand railing made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. |
| 22 | Providing and fixing pressed steel mitred door frames manufactured from commercial mild steel sheet of 1.25mm (16 gauge) thickness including hinges jamb, lock jamb, head and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface including filling with C.C 1:2:4( M-15 Grade)complete in all respect as directed by Engineerin-charge: Profile C |
| 23 | Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20 x 10 x 2mm and bracket with flat iron diagonals 20 x 5mm. size with top and bottom rail of T-iron 40 x 40 x 6mm. with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). With 75mm opening when closed |
| 24 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : South (Red / Choclate Colour) 1501 Cm2 to 3600 Cm2 Tiles |
| 25 | Providing and fixing anodized aluminum work (Anodizing to be got done from approved Anodizer) for doors ,windows, ventilators and partition with extruded built up standard tubular and other sections of approved make conforming to IS :733 and IS :1285 anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and thedirections of Engineer- in – charge .(Glazing and paneling to be paid for separately). For fixed portion |
| 26 | For shutters of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). |
| 27 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors ,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Prelaminated particle board with decorative lamination on both sides. |
| 28 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basicitem.) With glass panes of 5.0 mm thickness (weight not less than 13.75kg/sqm) as per IS : 2835. |
| 29 | Providing & fixing double action hydraulic floor spring of approved brand and manufacture to aluminum door shutterincluding cost of cutting floors as required, embedding in floors and cover plate etc. complete as per direction of Engineer In-charge. Confirmingto IS 6315 such as Sandhu/Amar or equivalent make. |
| 30 | Providing and Fixing Bearing Base door closure |
| 31 | Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12mm thick cement mortar of the same mix as that of masonry (lead caulking will be paid separately) : S.C.I. plain bend : 100mm |
| 32 | Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12mm thick cement mortar of the same mix as that of masonry (lead caulking will be paid separately) : Sand cast iron plain shoes : : 100mm |
| 33 | Supply and Installation of WALL – PREFABRICATED INSULATED CEMENT FACE PANEL: Factory-readymade structural reinforced insulated wall panel of thickness mentioned below. Panel shall be made of 6mm (+/-0.6mm) thick asbestos-free fiber cement sheet/ Cement bonded particle board as per IS:14276:1995 on both sides of rigid PUR insulation. The wall panel shall be vertically joined together with adjacent panel by biscuit joints lengthwise with suitable construction adhesive. Joining member (biscuit) shall be made of approx 12mm thick cement sheet /Cement bonded particle board as per IS:14276:1995. Panels may have optional provision for inbuilt electrical conduit running lengthwise at vertical center of specified panels. Both vertical lengthwise sides of panels must have full length MS tubes of min 1.0mm thickness for better structural strength.The final panel surface must be free from undulations. The Insulating core shall be self-extinguishing DIN 4102,Class B3 fire retardant class rigid PUR with thermal conductivity of 0.025 W/mK and with density of 40kg/m3 (+/-2kg) suitable for temperature range of -30 degree C to +80 degree C. The panel must be made using glue-free high pressure hot pressing self-bonding method and shall be free from major surface undulations. Thickness 65mm (+/- 2mm) |
| 34 | Supply and Installation of ROOF – PREFABRICATED INSULATED PPGL FACE PANEL: Roof: Insulated sandwich panels for roof of total thickness mentioned below exclusive of crest height of top corrugation. Panel shall be made of 0.50mm (+/-0.04mm) thick pre coated metal sheet on both sides of rigid polyurethane insulation. The top external facing metal sheet shall have corrugated shape with crest. The trapezoidal shape crowns/crest height should not be less than 30mm. The pre-coated metal sheet shall be PPGL (Pre Painted Galvalume Sheet with AZ coating) sheet having SDP (Super Durable Polyester) colour coat of 18 micron (min). The bottom sheet must have tongue and groove type flange (U shape) of 8mm x 8mm on groove side and 8mm x 12mm on tongue side. Flange must be on lengthwise sides for joining adjacent panels. Panel\"s bottom side PPGL sheet must also be pre-strengthened by full lengthwise stiffening with semi-circular beading of 12mm width & 3 to 4mm depth at 240 (+/-5) mm pitch. The top corrugated sheet must have at-least one open crown/crest for overlapping adjacent panel widthwise. Similarly the top corrugated sheet must have suitable open extension of min 6” on bottom widthwise side of panel for overlapping further panels joined lengthwise also. The insulation core shall be self-extinguishing DIN 4102,Class B3 fire retardant class rigid PUR with thermal conductivity of 0.025 W/mK and with initial density of 40kg/m3 (+/-2kg) suitable for temperature range of -30 degree C to +80 degree C. The panel must be made using glue-free high pressure hot pressing self-bonding method. PPGL sheet on both sides of panel shall have a min15 micron protective plastic guard film to avoid scratches during transportation. Thickness 65mm (+/- 2mm) |
| 35 | AccessoriesSupply and Installation of (Labour rate included in main item) Bottom and Top U track : U-track for mounting panels with floor. The channel shall be made from minimum 1.15 mm thick PPGL sheet with flange height of minimum 35 mm and width as per thickness of panel used. |
| 36 | Roof Ridge Cap: Ridge flashing for roof panels shall be made from 0.5mm thick pre-coated PPGL sheet of200mm x200 mm. |
| 37 | Roof Front Corrugated Cap: Front side flashing for roof panels (corrugated trapazodial shape) shall be made from 0.5mm thick pre-coated PPGL sheet. |
| 38 | Roof End Cap: End cap for closing ends of roof panels made from 0.5mm thick PPGL sheet. |
| 39 | Panel End Caps: U or L shape caps suitable for thickness of panel used, with 30mm flange. It should be made frem 0.5mm Pre coated PPGL sheet. |
| 40 | Self Drilling Screws: 5” |
| 41 | Self Drilling Screws: 3.5” |
| 42 | Self Drilling Screws: 1” |
| 43 | Structural steel work in single section fixed with connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete above plinth level upto 4.5 mtr height. In flats, tees, angles and channels. |
| 44 | P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 530x410mm. |
| 45 | P & F water closet Seat Covers with brass hinges complete : Solid PVC (ISI marked) grade-I Black for EWC. |
| 46 | P & F White Vitreous China Double Syphonic European W.C. (I.S:2556Mark) with mounted W.V.C. flushing cistern of (IS : 2556 Mark) of 10 litre capacity complete with all necessary internal fittings including cutting and making good the wall and floor. |
| 47 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: PVC with PVC bend as per IS : 7231 |
| 48 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 49 | P & F Toilet Shelf of approved quality/make: W.V.C. (I.S.: 2556 Mark) Size 550 mm |
| 50 | P & F Bib Cock (IS:8931 Mark) CP Brass bib cock, 15mm nominal bore. |
| 51 | P & F Grating of approved quality/make: Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make |
| 52 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make for Wash basin, Gyset etc. C.P. Inlet connection 15mm. Brass (IS:8931 marked) |
| 53 | P & F 15mm. Dia Connection Pipe of approved quality/make : PVC pipe with C.P. Brass nuts upto length 370mm |
| 54 | P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P. Pillar cock (IS : 8934 Mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall.: Size 510 mm x 400 mm |
| 55 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. Flat Back (large) or half stall size 610x400x80mm. |
| 56 | P & F PVC storage tank confirming to IS (12701/89) standards of approved make with cover, 25mm dia 1 M long G.I. Over flow pipe & 25cm. Long wash out pipe with plug & socket, including making connection etc., complete of approved design :1000 Litre Capacity |
| 57 | P & F PVC storage tank confirming to IS (12701/89) standards of approved make with cover, 25mm dia 1 M long G.I. Over flow pipe & 25cm. Long wash out pipe with plug & socket, including making connection etc., complete of approved design :500 Litre Capacity |
| 58 | Providing and fixing Polyethylene - Aluminimum - Polyethylene (PE-AL-PE) Composite Pressure Pipes as per 15450 : 2004 U.V. stablised with carbon black having thermal stabillity for hot and cold water supply with all compression type composite internal seal fittings (e.g. elbows, tees, reducers, couplers connectors etc.) including trenching & refilling the same etc. (External work) |
| 59 | (a) 1216 (16mm OD) pipe |
| 60 | Providing and fixing Polyethylene - Aluminimum - Polyethylene (PE-AL-PE) Composite Pressure Pipes as per 15450 : 2004 U.V. stablised with carbon black having thermal stabillity for hot and cold water supply with all compression type composite internal seal fittings (e.g. elbows, tees, reducers, couplers connectors etc.) including trenching & refilling the same etc. (External work) |
| 61 | (b) 2025 (25mm OD) pipe |
| 62 | P & F Full way valve (IS:778 Mark) or wheel valve of approved make : |
| 63 | (a) Gun-metal 15mm nominal bore. |
| 64 | P & F Full way valve (IS:778 Mark) or wheel valve of approved make : |
| 65 | (b) Gun-metal 25mm nominal bore. |
| 66 | P & F Ball Cock (IS : 1703 Mark) with Rod & P.V.C. Ball complete : Brass wt.400 gm. 15mm |
| 67 | P & F rigid PVC pipe (IS : 4985 mark) Class II (4Kg/ Cm2) approved quality/make including jointing the pipe with solvent cement rubber ring and lubricant: 110mm dia. |
| 68 | P & F Rigid PVC pipe fittings (IS : 4985 mark) of approved quality/make including jointing the fitting with solvent cement rubber ring and lubricant. |
| 69 | (A) Bend 87.5,110 mm dia |
| 70 | (B) Plain T 110 mm |
| 71 | (C) Pipe Clip110 mm dia |
| 72 | P & F Soap Dish or Tray of approved quality/make C.P. brass heavy and superior quality. |
| 73 | P & F Towel Rail or Ring of approved quality/make: C.P. brass Towel Rail elbow type with concealed screws size 600 mm (Heavy duty). |
| 74 | P & F Bevelled edge Mirror of special glass of approved make (Atul, Modi Guard, Saint Gobin or equivalent) complete with 6mm thick asbestos cement sheet ground fixed to wooden screws & washers. |
| 75 | Construction of Man hole, in all types of soil, inner size 1.5 x 1.2 M, with 450mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20mm thick inside plaster in CM 1:6, finished with floating neat cement, 50 mm thick M-15 grade C.C. flooring making channels, 80 mm thick stone slab covering with 40 mm thick M-15 grade C.C.flooring, Ferro Cement cover with frame of 450mm dia, earthwork etc. complete including disposal of surplus earth within 50 mtr. lead as per design : Depth up to 0.5 M |
| 76 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size 300 X 300 mm depth upto 0.5 MCement cover with frame. |
| 77 | Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: Size 300 cm. dia outside & 300 Cm. depth |
| 78 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C flooring & over stone slab covering ,80 mm thick slab ,jointing of slab in CM 1:3. Ralthal, Kharanja,50 mm thick stone partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos C.I foot rests of approved design ,two No. 450 mm dia each Ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 400x140x150 cm.(for 50 users) |
| 79 | P & F Sand-cast Iron (S.C.I.) Pipe (IS : 1729mark) of approved make in wall or in floor with M.S. holder bat clamps in 10 X 10 X 10 Cm. M-15 grade concrete blocks, joints filled with CM 1:4 with spun yarn including cutting holes and making good the wall: 100mm dia |
| 80 | P & F Twin- peg of approved quality / makeC.P. brass (heavy)Superior quality |
