Construction Work For Dairy Development Directorate Building At Haldwani, District- Nainital, Haldwani-Uttarakhand

TDR : 32121564

Tender Notice
BOQ

Expired

Haldwani , Uttarakhand

Tender Brief : Construction Work For Dairy Development Directorate Building At Haldwani, District- Nainital

Document Fees
₹ 2360 /-

EMD
₹ 840000.0 /-

Tender Value
₹ 4.20 Crore /-

Submission Date
27-05-2022

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
2	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
3	Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
4	Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.
5	Construction of embankment with approved material obtained from borrow pits cu.m (including cost of compensation for earth taken from private land) with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.53 km @ 127.01Rs.,[email protected] = 127.01+125.75=284.51Rs.
6	Construction of embankment with approved material obtained from borrow pits cu.m (including cost of compensation for earth taken from private land) with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.53 km @ 127.01 Rs.,[email protected]= 127.01+157.50=284.51Rs.
7	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
8	Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).
9	Applying a coat of residual petroleum bitumen of grade of VG-10 ofapproved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
10	Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
11	Providing and laying in position specified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)
12	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)
13	Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level
14	All works above plinth level upto floor V level
15	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars
16	Centering and shuttering including strutting, propping etc. and removal ofform for :Foundations, footings, bases of columns, etc. for mass concrete
17	Centring and shuttering for Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc.
18	Columns, Pillars, Piers, Abutments, Posts and Struts
19	Lintels, beams, plinth beams, girders, bressumers and cantilevers
20	Suspended floors, roofs, landings, balconies and access platform
21	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
22	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)
23	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)
24	Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.(withF.P.S.bricks).
25	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
26	Providing and fixing ISI marked flush door shutters conforming toIS: 2202 (Part I) non-decorative type, core of block board construction with frameof 1st class hard wood and well matched commercial 3 ply veneering with verticalgrains or cross bands and face veneers on both faces of shutters
27	Providing and fixing ISI marked oxidised M.S. sliding door bolt with nuts andscrews etc.:300x16 mm
28	250X16 MM
29	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250x10 mm
30	150X10 MM
31	Providing and fixing ISI marked oxidised M.S. handles conformingto IS:4992 with necessary screws etc. 125 MM
32	Providing and fixing oxidised M.S. casement stays (straight pegtype) with necessary screws etc.
33	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screwsetc. complete :300x16 mm
34	250x16 mm
35	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
36	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm
37	150X10 MM
38	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper
39	Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading
40	Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood
41	Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: Profile B Fixing with adjustable lugs with split end tail to each jambProfile\"B\" (Single Pattam)
42	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separatel
43	Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes
44	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets,
45	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
46	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
47	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
48	Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of requiredength (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVCextrudedinterlocks, EPDM gasket, wool pile, zinc alloy (white powder oated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rodof required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes, wire mesh and silicon sealant shall bepaid separately) Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing beadof appropriate dimension. (Area of window above 1.75 sqm).
49	Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.400 x 19 x 1.9 mm
50	Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc.complete.
51	Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm
52	Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm
53	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.
54	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
55	Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
56	Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with Raj Nagar plain
57	Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.
58	Providinggola75x75mmincementconcrete1:2:4(1 cement:2coarsesand:4stoneaggregate10mmanddowngauge) includingfinishingwithcementmortar1:3(1cement:3finesand) asperstandard design : In 75x75mm deep chase
59	Makingkhurras45x45cmwithaverageminimumthickness of5cmcementconcrete1:2:4(1cement:2coarsesand:4 gradedstoneaggregateof20mmnominalsize)overP.V.C.sheet1mx1mx400micron, finished with 12mm cement plaster 1:3 (1cement :3coarsesand)andacoatofneatcementroundingthe edgesandmaking and finishing the outlet complete.
60	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes110 mm diameter
61	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories 110 mm
62	Bend 87.5 degree(110 mm bend)
63	Shoe (Plain) (110 mm Shoe)
64	Providing and fixing unplasticised -PVC pipe clips of approveddesign tounplasticised-PVCrainwater pipesbymeans of 50x50x50 mmhardwoodplugs,screwedwithM.S.screwsofrequiredlength including .110 mm
65	12 mm thick cement plaster in 1:4 ( 1 cement and 4 fine sand) mortar including supply of all material , labour and T&P etc. required for proper completion of the work.
66	12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)
67	15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)
68	Cement plaster (1:3) finished with a floating coat of neat cement.20 mm Cement Plaster
69	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete..
70	Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water tinnable priming coat with cement primer
71	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)
72	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)
73	PaintingwoodworkwithDeluxeMultiSurfacePaintofrequired shade.Twoor more coat applied @0.90ltr/[email protected]/10sqm ofapproved brand or manufacture
74	French spirit polishing : Two or more coats on new works including a coat of wood filler
75	Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
76	12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)
77	6mm cement plaster of mix 1:3 (1 cement: 3 fine sand)
78	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
79	Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres
80	Supplying and stacking at site.90 mm to 45 mm size stone aggregate
81	63 mm to 45 mm size stone aggregate
82	\"Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately)Cement content considered in M-30 is @ 340 kg/cum.
83	Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out completeNew work (Two or more coats)
84	Surface dressing one coat on new surface with bitumen of specified grade at a rate of 1.95 kg/sqm of surface area with 1.5 cum of stone chippings 13.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity , etc. complete :
85	Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 Rectangular shape 600x450 mm internal dimensions
86	Inlet Pipe 100 mm dia
87	Outlet Pipe 100 mm dia
88	Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long co mplete as per standard designWith common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5
89	Constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1cement :4 coarse sand ) with C.c 1:2:4 floor over C.C 1:5:10 Finished with a floating coat of neat cement complete .Rectangular shape 600x450mm internal dimensions
90	Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture
91	Supplying and fixing C.I. cover 300x300 mm without frame forgully trap (standard pattern) the weight of cover to be not less than 4.5kg
92	Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spacedjoints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \"T\" at 600 mmenter to center to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.GI Metal CeilingLay in plain Tegular edgeGlobal white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made ofG I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.
93	Cornices and mouldings
94	Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc.
95	Extra for plastering done on moulding, cornices or architraves including neat finish to line and level:In two coats
96	Providing & Fixing UniStone tile made Unistone cement mortar 1:3 ratio and cement slurry @ 3.3 kg/Sqm Including Pointing in white cement complete
97	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry
98	Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
99	Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage.
100	For vertical surface two coats @0.70 kg per sqm per coat
101	For horizontal surface one coat @1.10 kg per sqm.
102	Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured forpayment).
103	Acoustical work in wall panelling in wooden finishing
104	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.15 mm dia. nominal bore
105	20 mm dia. nominal bore
106	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.
107	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :15 mm nominal bore
108	20 mm dia. nominal bore
109	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931
110	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore.
111	Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore
112	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore (Horizontal)
113	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
114	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked black solid plastic seat and lid
115	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap
116	Providing and fixing soil, waste and vent pipes :100 mm dia Sand cast iron S&S pipe as per IS: 1729
117	75 mm diameter :
118	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :for 110 mm dia pipe
119	for 75 mm dia pipe
120	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
121	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore
122	Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Circular shape 450 mm dia
123	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
124	Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
125	Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
126	Providing and fixing double equal plain junction of required degree.100x100x100mm
127	75x75x75x75 mm
128	Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete100 mm diameter pipe
129	75 mm diameter pipe
130	Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 250 mm
131	Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern
132	Providing& Fixing ACN-1135N Soap Dispenser with Glass Bottle make Jaquar
133	Excavating trenches of required width for pipes, cables, etc including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil
134	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars 250 mm dia. R.C.C. pipe250 mm dia RCC pipes.
135	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, totalweight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
136	Extra depth for manholesSize 90x80 cmWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5
137	Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 Rectangular shape 600x450 mm internal dimensions
138	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
139	Providing & Fixing Lift8 person capacity
140	Supply , Installtion , Testing and comissioningof CAT 6 UTP cablesolid copper conductors Approved Makes: Belden/Siemon/Panduit/Der Wiser/Molex/Dlink
141	Supply , Installtion , Testing and comissioning of CAT6 information outlet (I/O) for Data, Voice & Wi-Firack endApproved Makes: Belden/Siemon/Panduit/Der Wiser/Molex/Dlink
142	Supply , Installtion , Testing and comissioning of loaded 24 port CAT6jack panel for CAT6 cable termination Approved Makes: Belden/Siemon/Panduit/Der Wiser/Molex/Dlink
143	Supply , Installtion , Testing and comissioning of CAT6 patch cord 3 feet for rack side switch termination for user End Approved Makes: Belden/Siemon/Panduit/Der Wiser/Molex/Dlink
144	Supply , Installtion , Testing and comissioningof CAT6 patch cord 7 feet for user termination to information outlet Rack End Approved Makes: Belden/Siemon/Panduit/Der Wiser/Molex/Dlink
145	Supply , Installtion , Testing and comissioningof 1, 2 and 4 port face plate white for I/O fixing at user side. Approved Makes: Belden/Siemon/Panduit/Der Wiser/Molex/Dlink
146	Supply , Installtion , Testing and comissioningof 42 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts. Approved Makes: Poweride/MTS/Rittal/APC/APW
147	Supply , Installtion , Testing and comissioningof 12 Uwall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts. Approved Makes: Poweride/MTS/Rittal/APC/APW
148	Supply of IP Based voice Communication System with 04 Port Voicemail ,04 Port FXS ,04 Port FXO with CLIP Facility ,100 IP users License ,01 Nos. IP Operator Console,8 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, - Redundant server in active-redundantmode. Approved Makes: Alcatel -OXE /Cisco /Polycom/ barracuda/ netfortris/EPGY,Grandstream
149	Supply of Type 1 IP Phone . Graphic LCD display with backlight 1user accounts with multi-line appearance keysLocal and company-wide phone directories Approved Make : Alcatel -OXE /Cisco /Polycom/ barracuda/ netfortris/Grandstream
150	Supplyof Type 2 IP Phone 1 VoIP account , Full duplex speaker phone, IPV6, 2xLAN, PoEApproved Make : Alcatel -OXE /Cisco /Polycom/ barracuda/ netfortris/Grandstream
151	Supply, Installation, Testing & Commissioning of Core Switch with 12 Fiber SFP Port as per technical pecificationApproved Make : Cisco// Juniper / HP/ Ruckus/Dlink
152	Supply, Installation, Testing & Commissioning of 24 Port POE+ Access having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE + and 2x 1G SFP+ uplink ports . Approved Make : Cisco// Juniper / HP/ Ruckus/Dlink
153	Supply, Installation, Testing & Commissioning of fiber Modules 1000BASE Approved Make : Cisco// Juniper / HP/ Ruckus/Dlink
154	Supply, Installation, Testing & Commissioning of Internet Security solution with minimum of 50users from day one with one year subscription/license and flexibility to scale up to 75 users in future having 99% uptime with each level redundancy, single pane of glass for reporting multi-location and roaming users environment for all the asked features with minimum 3 months of logs retention capacity.Sophos/Palo Alto/Checkpoint/Fortinet
155	Supply , Installation , Testing and Comissioning of802.11 a/b/g/n Indoor Wi-Fi- Access point ,dynamic radio management. Approved Makes:Cisco/ Juniper / HP/ Ruckus/Dlink
156	Supply , Installation , Testing and commissioningof CAT RG 6 cable solid copper conductors Approved Makes: Belden/Siemon/Panduit/Der Wiser/Molex/Dlink
157	Supply, Installation, Testing & Commissioningof 27 U Network Rack with19\"\"PDU 6 points 5 amp , Stationary shelf, Mounting Hardware(pac. Of 10) , Cable manager Horizontal 1U,Fan 230 vac 90 cfm top mounted. Approved Makes: Poweride/MTS/Rittal/APC/APW
158	Supply installation testing and commissioning of 2 MP AHD Domecamera ,UL,CE,FCC certified , Metal housing ,2.8mm - 12mmvari-focal lens, 1/4\" CMOS sensor size , Shutter speed : 1/25 - 1/10,000 Sec , Min illumination : 0.1Lux @ (F1.2,AGC ON), 0.05 Lux with IR , Inbuilt IR LED , IR Distance upto 30 mtrs , IP 66 weather proof.Approved Make : Impulse,Bosch,Pelco,Vicon /UNV
159	Supply installation testing and commissioning of 2 MP AHD Bullet camera ,UL,CE,FCC certified , Metal housing ,2.8mm - 12mmvari-focal lens, 1/4\" CMOS sensor size , Shutter speed : 1/25 - 1/10,000 Sec , Min illumination : 0.1Lux @ (F1.2,AGC ON), 0.05 Lux with IR , Inbuilt IR LED , IR Distance upto 30 mtrs , IP 66 weather proof.Approved Make : Impulse,Bosch,Pelco,Vicon /UNV
160	16 Channel DVR , UL,CE,FCC certified , H.264 video compression , linux operating system , 16 channelanalog input , 8 channnelIP input , 2 SATA HDD Slot , 8 TB HDD support in each slot , 2 X USB port , 1 X VGA , 1 X HDMI , Display resolution :Analog : 4MP / 3MP / 1080P / 720P / 960H ,IP : 4MP / 3MP / 1080P / 720P / 960H,Support Mobile Phones based on iPhone and Android operation system
161	Supply, Installation, Testing and Commissioning of Full HD 32 \" LED Professional Display Panel. Approved Make :- Samsung ,panasonic ,Sony,philips
162	Supply, Installation, Testing & Commissioning of Suitable power supply for Camera.Approved Make : Protek/CPS/N-TEK
163	Supply and installing MS. Pipe \"C\" Class, IS 1239 standard including cutting, welding etc. Providing all required accessories like flanges, bends tees, reducers, supporting with GI. clamps etc. including painting with one coat of primer and two coat of red Synthetic enamel paint of aoopproved make &shades.(Pipe of TATA / JINDAL/SURYA) 150 mm dia
164	Supply & Installation C.I. Butterfly valve of PN1.0 Rating , confirming to IS standard , complete with Flanges, gasket and nuts , bolts , etc .CASTELE/KARTAR/SANT150 mm dia
165	Supply , erecting and commissioning of Landing Hydrants comprising of the following in the fire duct;Providing and fixing single headed landing valve (hydrant) of 63 mm dia made of SS Hydrant valve ISI. Mark is completed with erection and necessary fitting etc. Confirming to IS: 903. OMEX /NEW AGE/ MINIMAX/GETECH
166	Providing and fixing impact, abrasion and weather resistant rubberized fabric lined (RRL) hose pipe confirming to IS:636-1979 (TYPE A) of 63 mm dia and 15 meter length with SS instantaneous male and femalecouplings confirming to IS:903:1975. OMEX /NEW AGE/ MINIMAX/GETECH
167	First Aid Hose Reel Complete With hose Drum and 30 m hose for Internal fire Fighting .Omex new Age /Minimax getex
168	Providing and fixing doors for Internal hose cabinet made of ms / al angle with glass doors suitablepable of accommodating landing valve, hose pipes, fittings & accessories. OMEX/SB/NEWAGE
169	supplying and fixing approved make 25mm dia. Automatic air release valve
170	63 mmNozzle
171	Providing and fixing of air vessel. 200 MM DIA X 1200 M
172	Anti vibration ,mountings for pipemlines Kandwal100 mm dia
173	Pressure Gauge. DANFOSS make
174	Providing & fixing CO2 Type Fire Extinguisher complete with Refill, ISI marked Tested & Approved.capacity 9 kg
175	Suppling and fixing 9 kg . Sand bucked along with bracket grouted in walls with necessary hardware. The bracket will be stove enamel painted inside with white colour and red comour outside. Also FIRE, letters to painted in white enamel paint on outside surfase.
176	Fire buckets round bottom type enamel painted, white inside & Red out side and along with stand fabricated from MS angle to accommodate 4 buckets
177	Providing & Fixing pump near Terrace tank type-Monobloc MB G1.52 (1.5 HP) Pipe Size 40x32 (1.1 Kw) 3000 RPM (SYN) Head Range 15-28.5) discharge (175-50 LPM
178	WGSTLPT Point wiring in PVC conduit, with modular type switch.Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.
179	WGSTLPT Point wiring in PVC conduit, with modular type switch. Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C
180	WGSTLMIDTC Twin Control point wiring inPVC conduit, with modular type switch:Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.
181	WGSTLPP2 Power plug wiring inPVC conduit (2x4 sq. mm)Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.
182	TLWGEC Telephone wiring inPVC conduit:Supplying and drawing following pair, 0.5 sq mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.2 Pair(@30M EACH)
183	WGSTLSB Circuit/ submain wiring inPVC conduit:Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
184	4 X 6 sq. mm + 2 X 6 sq. mm earth wire
185	4 X 10 sq. mm + 2 X 6 sq. mm earth wire
186	PVCCON S/F PVC conduit:Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required.25 mm
187	MB S/F metal boxes:Suppying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. required.75 mm x 75 mm x 60 mm deep
188	PTSWEB S/F modular type switch/ socket:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch
189	3 pin 5/6 amp socket outlet
190	Telephone socket outlet
191	MODFREB S/F modular type electronic fan regulator: Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
192	LPACCPT S/F light plug point modular type accessories:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).
193	PPACCPT S/F power plug point modular type accessories:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
194	CREB S/F ceilling rose:Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required
195	BRHOLD S/F brass holder:Supplying and flxing brass batten/angle holder including connection etc. as required.
196	Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.
197	ITCFFSUR ITC fluorescent fitting directly on surface:Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
198	ITCCFFC ITC ceiling fan with cover on fan box:Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
199	ITCEF450 ITC exhaust fan upto 450 mm sweep: Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.
200	LOUSHEF Fixing louvers/shutters for exhaust fan:Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.
201	PWTPMCBDB S/F TP MCB DB:Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door
202	6 way (4 +18), Double door
203	PWTPMCBDB S/F prewired TP MCB DB:Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator)6 way (4 + 18), Double door
204	MCBTPIS S/F TP MCB isolator:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required.63 amps
205	MCBC S/F \"C\" curve, SP MCBSupplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole
206	EARGIPL G.I earth plate elctrode:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required..
207	EARG125X6 S/L 25 mm x 5 mm G.I. earth strip in ground:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
208	Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes.3.5c x 95 sq. mm cable
209	3.5c x 50 sq. mm cable
210	3.5c x 25 sq. mm cable
211	4c x 16 sq. mm cable
212	Supply & fixing of 20 W Solar LED street Light System, Solar Standalone Street Light system mentioned below includes LED street Light in built SCC, SPV Panel Battery, HDG Tubular Pole, Connecting Wire etc. of standard make (Havells) complete in all aspects as per direction of Engineer in Charge
213	Supply & fixing of Decorative gate light Globe shaped post top lantern in frosted finish made up ofPolycarbonate, suitable upto 27 W retrofit CFL (B-22 Badw) complet in all aspect as per direction of Engineer in charge
214	CEILLING FANSupply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-ES 50 (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge1200 mm sweep
215	Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete . Model- Ventil Air - DS (Make :Havells) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge. 300 mm sweep 900 rpm
216	Supply and fixing ofLED Tube light1200mm 20W 865 T8 IP20 ,Lumen Output-1600 , 3000, 4000, 6500K ceiling mounted LED batten (E-LITE LED TRIYCA) , extruded aluminium heat sink provided for efficient heat deissipation 7& integrated electronic driver. ( 1x20 W LED Double 6500K) complet in all aspects as per direction of Engineer in charge.
217	SUPPLY OF LED Bulb 15 W,230/250 VOLT,50 HZ ETC,
218	Supply Of Daikin Split AC (i) 1.5 TR Split Unit (5 Star) Model No:-FTF50QRV
219	CEILING LIGHTProviding and Fixing 18W 840 2x2 LHEWBPP6PW1W018 HSN Code 9405 Fixture size in mm (LxWxH) 600x600x70 for 2x2, Fixture size in mm (LxWxH) 1200x300x70 for 4x1.as per engineer in charge

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Uttarakhand Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Construction Work For Dairy Development Directorate Building At Haldwani, District- Nainital, Haldwani-Uttarakhand

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Construction Work For Dairy Development Directorate Building At Haldwani, District- Nainital, Haldwani-Uttarakhand

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us