|
| 1 | Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseleing or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs (Three metres) clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimetre)layers, whenrequired into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 2 | Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation footings, bases of columns and mass concrete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. |
| 3 | Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including mouldings, cornices etc; whereever required within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. |
| 4 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders and lintels sides and soffits of beams, beam haunchings, cantilevers bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 5 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings as per Architectural drawing and the like within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government |
| 6 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick,welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforcedconcreteand plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, within allleads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 7 | Providing and laying cement concrete1:4:8 (One cement isto Four sand isto Eightgraded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 8 | Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : Six sand : Twelve graded crushed stone aggregate 20mm (Twenty milimetres) nominal size) at plinth level in cement mortar 1:6 (One cement: Six sand) complete, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 9 | Providing and laying cement concrete work ofgradeM-20 (M- twenty)mix design to obtain the minimum crushing strength of 20N/mm square with minimum cement contents of330 kg (Three hundredthirty kilogram) per cubic meter to give an smooth surfaces mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns and the like mass concrete within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. |
| 10 | Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter) cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts for all floors heights within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 11 | Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter)cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves their supports balconies, beams, girder, bressumers and cantilevers etc; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 12 | Providing and laying cement concrete work of grade M-20 (M- twenty) design mix to obtain the compressive strength of 20N/mm2 (twenty newton per square millimeter)cement contents not less than 320 kg (Three hundred twenty kilogram) per cubic meter, mechanically mixed and vibrated including curing complete, excluding cost of form work and reinforcement for reinforced concrete work in Stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor level within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 13 | Providing and laying upto first floor two level reinforced cement concrete 1:2:4 (One cement is to two Sand is to four graded stone aggregate 20mm( Twenty millimeter )nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcementMouldings as in cornices windows, sills etc. not exceeding 15cm ( Fiifteen centimeter)in girth.in completeas directed bytheEngineer-in-Charge, including carriageof materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or anyother taxes imposed by the Government. |
| 14 | Providing Tor steel reinforcement of Sail / Tisco for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floorswithin all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 15 | Second Class Bricks work using common burnt clay building bricks in super-structure upto all floor level with Cement Mortar 1:6 (One Cement : Six Sand)within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. |
| 16 | Providing 2nd (second) class deodar wood work in frames doors, windows, clerestory, windows and other frames wrought, framedand fixed in positionwithin all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 17 | Providing and fixingon wall face 100mm (One hundred milimetres) diametres P.V.C. rain water pipes of water pressure 4/6kg (four / six kilogramme) as per ISI finolex / Ralpipe / vectos or its equivalent pipe confirming to IS code 13592 for rain water pipe fixed with approved adhesive includingfilling the joints complete within all leads, lifts of materials and other incidentals, and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 18 | Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet ISI marked - Z 120 of tata / sail / reliance / jindal in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (Six milimetres) diametres with prepainted limpet and rubber washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 19 | Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with0.60cm (Zero decimal Sixty centimetres) thick prepainted steel sheet ISI marked - Z 120 of approved make in ridges (Factory made) of sail / relience / Jindal shall be having proper Gola/Shape of steel sheet Tata/ Sakti with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyester of 5 (Five) microns over 5 (Five) micronsprimer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 20 | Providing and fixing 40 mm (forty millimetre) 2nd (second) class deodar wood work panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 21 | 6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 22 | Providing and fixing 20mm CementMortar 1:6 ( One is to six ) plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth complete as directed bytheEngineer-in-Charge, including carriageof materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or anyother taxes imposed by the Government |
| 23 | 15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 24 | Providing and fixing 40 mm (forty millimetre) thick 2nd (second) class deodar wood work wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 25 | Supplying and fixing Plain Glass. 3mm ( three millimeter ) thick glass panes with putty and nails including removal of broken glass panes wherever necessary:- as directed bytheEngineer-in-Charge, including carriageof materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or anyother taxes imposed by the Government . |
| 26 | Providing & fixing 250x16mm anodized matt finished aluminium Pilot/Sheet or equivalent sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. whithin all leads, lifts of materials and other incidentals. As per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government. |
| 27 | Providing and fixing 250x10mm (Two hundred fifty into Ten milimetres) size aluminium Pilot/sheel anodized transparent or dyed to required colour and shade with necessary screws etc.Tower bolts (Barrel type) as approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government |
| 28 | Providing and fixing 150x10mm (One hundred fifty into Ten milimetres) size aluminium Pilot/sheel anodized transparent or dyed to required colour and shade with necessary screws etc.Tower bolts (Barrel type) as approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government |
| 29 | Providing and fixing 125mm (one hundred twenty five millimetre) aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 30 | Providing and fixing 100mm (one hundred millimetre) aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 31 | Providing and fixingWhite glazed tiles 6 mm( Six millimeter)thick in flooring, treads of steps and landing laid on a bed of 12 mm ( Twelve millimeter ) thick cement mortar 1:3(Onecement is to threesand) finished with flush pointing in white cement as directed bytheEngineer-in-Charge, including carriageof materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or anyother taxes imposed by the Government. |
| 32 | White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm ( twelve millimetre nominal size ) thick cement mortar 1:3 (Onecement in to threesand) and jointed with cement slurry. as techanical specification clause 1603.1 as per the direction of Engineer –in-charge including carriage of materials within all leads and lifts and other incidentals. The rate including octroi , royality, Malkana ,toll tax , sale tax or other taxes imposed by the Government. |
| 33 | Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 34 | Applying Readymixed priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required with as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 35 | Painting two coats (excluding priming coat) on new concrete masonry/plaster surfaces with readymixed paint brushing for use on floors to give an even shade including cleaning the surface of all dirt,dust and other foreign matter and sand papering as required with Paint other than white within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 36 | Finishing wall with weather proofexterior grade emulsion of approveddesign (Apexultima) or its equarliedon undecorated wall surfaces (twocoats) to give an even shade andfinal finish after throughly cleaning thesurface to remove all dirt, dust andother foreign matter etc includingsand paper smooth complete. as directed bytheEngineer-in-Charge, including carriageof materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or anyother taxes imposed by the Government . |
| 37 | Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer- Incharge. |
| 38 | Painting two or more coats (excluding priming coat) over new wood and wood based surfaces with Nerolac/ Asian or equivalent with enamel paint other than white brushing to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter . within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 39 | Providing and fixing 6 mm (six millimetre) thick plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately) as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 40 | Steel work welded in built up sections trusses and framed work,including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paintin gratings framed gaurds, bars, ladders, railing, brackets and similar work, within all leads, lifts of materials and other. Incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge |
