Public Works Department-PWD has published Construction Of Bus Terminal At Nagerjala, Agartala I Construction Of Terminal Building, Ii Construction Of Rehabilitated Shops Sh Building Portion Including Internal Water Supply And Sanitary Installation. Remaining Work. Submission Date for this Tender is 18-04-2022. Building Work Tenders in agartala Tripura. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation,grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. - All kinds of soil By mechanical means |
| 3 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level. (ii) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 5 | (iii) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 6 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level: (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 7 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- in wall (any thickness) in/c attached plaster outtresses, piers, boundary etc- 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 8 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- a) RCC work in suspended floors, roofs having slope upto 15° landings, balconies, shelves and chajjas. - 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 9 | b) RCC work in beams, lintels, bands, plain window sills, staircases and spiral staircases excluding precast spiral staircase. - 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 10 | Providing and laying upto floor five level reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers facias and eaves boards excluding the cost of centring, shuttering, finishing and reinforcement- (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 11 | Centering shuttering including struttings, propping etc. and removal of form work for: (i) Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 12 | (iii) Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 13 | (iv) Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply |
| 14 | (v) Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 15 | (vi) Stairs (excluding landings) except spiralstaircases with wooden plank |
| 16 | (vii) Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards |
| 17 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor five level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 18 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 19 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 20 | Providing and fixing 18 mm thick plain marble stone, mirror polished, machine cut for, kitchen platforms, vanity counters, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing etc. complete at all levels as required:- Rajnagar Plain white marble/ Udaypur green marble/ Zebra black marble or equivalent duly approved:- Area of slab upto 0.50 sqm. |
| 21 | Extra for providing edge moulding to 18 mm thick marble stonecounters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete at all levels as required as per design approved by the Engineer-in-charge:- Marble work. |
| 22 | Providingandfixing18mm thick stoneslabtablerubbed, edgesroundedand polishedofsize75x50cmdeepand1.8cmthickfixedinurinal partitions by cutting a chase of appropriate width withchasecutter and embeddingthestoneinthechasewithepoxygroutorwithcement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 6 mm nominalsize)as perdirection ofEngineer-in-chargeandfinished smooth including rubbing, curing etc. complete at all levels as required (measurement should be of exposed finished work):- White Agaria Marble Stone of approved shade or equivalent duly aproved. |
| 23 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position Local Teak wood |
| 24 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 25 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 26 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : |
| 27 | Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm |
| 29 | 250x16 mm |
| 30 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 300x10 mm |
| 31 | 250x10 mm |
| 32 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :125 mm |
| 33 | 100 mm |
| 34 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper |
| 35 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of 65/100 mm size complete as per manufacturers" specification and direction of Engineer-In-Charge. |
| 36 | Providing and fixing to existing door frame 30mm thick factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, top & bottom rails. M.S .frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC ‘C channel of size 30mm thickness, 110mm width out of which 90mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 110mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on the inner side to form top and bottom rail and 130mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall be provided as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide PVC sheet bending on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacture’s specification & drawing. |
| 37 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes |
| 38 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required:- M.S. tube |
| 39 | Providing and fixing MS bolts including nuts and washers complete as per standard design:- Above 300mm length. |
| 40 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 41 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required |
| 42 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:- 80xl.25mm M.S. laths with 1.25 mm thick top cover. |
| 43 | Providing and fixing ball bearing for rolling shutters (exceeding 10 sqm area) of approved make complete as required. |
| 44 | Providingandfixingaluminiumworkfordoors,windows,ventilators, stair railing including hand rail andpartitionswithextrudedbuiltupstandardtubularsections/ appropriateZsectionsandothersectionsofapprovedmake conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws orwithfixingclips,orwithexpansionholdfastenersincluding necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawingandthedirectionofEngineerincharge.(Glazingand paneling to be paid for separately) :- a) For fixed portion of approved quality:- Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 45 | b) For shutters/ sliding shutters of doors, windows & ventilatorsincluding providing and fixing hinges / pivots / rollers and making provision for fixing fittings wherever required including the cost of PVC / neoprene gasket required of approved quality ( Fittings shall be paid for separately ):- Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 46 | Providing and fixing glazing of approved quality in aluminium doors,windows, ventilator, shutters and partition frames with PVC / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge :- a) With glass/float glass panes of 4.0 m thickness ( weight not less than 10.0 kg / sqm ) |
| 47 | b)With glass/ float glass panes of 5.5 m thickness ( weight not less than 13.50 kg / sqm ) |
| 48 | Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:- 205 x 19 mm |
| 49 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality completeas per direction of Engineer-in-charge:- Anodised aluminium of grade AC 15 ). |
| 50 | Providing, fitting & fixing in position 4mm thick aluminium composite panel (ACP) cladding of approved make, fabricated to flat, smooth curved to required radius,circular ring cladding to shapeas per requirement( exterior / interior surface), in metalic colours using prefabricated aluminium extruded profiles of alloy-6063 T6 in chromatized finish to withstand the design wind pressure of 200 Kg/ sqm. The fastening brackets of aluminium/ hot dip galvanised with SS-304 screws, fasteners and anchor bolts complete with nylon seperators to prevent bi-metallic contacts. ACP sheets will be fixed with both ways Norton tape and Dow coring 995 structured sealant, including necessary scaffolding complete, as per approved architectural drawing, design and direction of the Engineer -in charge. |
| 51 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch including fixing with polymer coated "J" or "L" hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2"or 3"or 6") as specified. |
| 52 | Providing and fixing Marble stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishing complete. 18 mm thick Marble stone Raj Nagar plain marble |
| 53 | Extra for marble flooring complete in treads of steps and risers using single length upto 2.00 metre. |
| 54 | Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishing complete. 10.31.1 Kota stone slab 25mm thick |
| 55 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 56 | Providing and laying 1st quality ceramic glazed floor tiles 300 x 300 mm conforming to IS : 15622 ( thickness to be specified by the manufacturer ) of approved make in colours, shades such as white, ivory, grey, fume red, brown over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete |
| 57 | Providing and laying polished vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % and conforming to IS : 15622of approved make in all colours, shades over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. Size of tile 80x80 cm |
| 58 | Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. complete. 40mm thick. |
| 59 | Providing and laying cement plaster skirting upto 300 mm height with cement mortar 1 : 3 ( 1 cement : 3 fine sand ) finished with a floating coat of neat cement including rounding of junctions etc. complete. 18 mm thick |
| 60 | 21 mm thick |
| 61 | Extra for providing and fixing glass strips in joints of terrazo flooring complete 40 mm wide and 4 mm thick. |
| 62 | Providing and fixing precast chequered cement concrete tiles 22 mm thick, laid in footpath & courtyard, on 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete. In dark shade using ordinary cement |
| 63 | ProvidingandfixingonwallfaceunplasticisedRigidPVCrainwater pipes (working pressure 4 kg / cm2)conformingto IS : 13592 Type Aincludingjointingwith sealring conformingtoIS:5382leaving10mmgapforthermalexpansion: Single socketed pipe - 110 mm OD |
| 64 | Providingandfixing on wallface unplasticised - PVCmouldedfittings/ accessoriesfor unplasticised Rigid PVC rain water pipes conforming to IS:13592TypeAincludingjointingwith sealringconformingtoIS: 5382 leaving 10 mm gap forthermalexpansion: Coupler 110 mm |
| 65 | Single equal tee without door 110x110x110mm |
| 66 | Single equal tee with door 110x110x110mm |
| 67 | Bend 87.5° 110mm |
| 68 | Plain shoe 110mm |
| 69 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVCrainwater pipesbymeansof50x50x50mmhard woodplugs,screwedwithM.S.screwsofrequiredlengthincluding cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. 110mm |
| 70 | Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. 100mm |
| 71 | 12 mm cement plaster in single layer including cost of materials required and finishing even and smooth and curing complete.In cement mortar 1 : 4 ( 1 cement : 4 fine sand) |
| 72 | In cement mortar 1 : 6 ( 1 cement : 6 fine sand) |
| 73 | 15 mm cement plaster in single layer including cost of materials required and finishing even and smooth and curing complete. In cement mortar 1 : 6 ( 1 cement : 6 fine sand) |
| 74 | 6 mm cement plaster of mix : Cement mortar 1:4 (1 cement : 4 fine sand) |
| 75 | Neat cement punning. |
| 76 | Distempering with oil bound washable distemper of approved brand and manufacture and of required shade on new work ( two or more coats ), over and including a priming coat of cement primer to give an even shade complete. |
| 77 | Finishing walls with premium acrylic smooth exterior paint of required shade of approved brand and manufacture on new work ( two or more coats applied @ 1.43 kg/10 sqm ) over and including base coat water proofing cement paint applied @ 2.20 kg/10 sqm complete. |
| 78 | Applying priming coat: With ready mixed pink primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 79 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel, galvanised iron / steel work. |
| 80 | Painting with synthetic enamel paint ( two or more coats ) of required colour of approved brand and manufacture on new work to give an even shade. |
| 81 | Providing and laying grading of roof for water proofing treatment complete as required as per direction of the Engineer-in-charge:-Cement concrete 1:2:4 ( 1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size ). |
| 82 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushingcisternwithmanuallycontrolleddevice(handlelever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 83 | Providingandfixingwhitevitreouschinapedestaltypewatercloset (Europeantype W.C.pan)withseatandlid,10litrelowlevelwhite P.V.C.flushing cistern withmanually controlled device (handlelever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 84 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively. |
| 85 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. |
| 86 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings: Flat back wash basin of size 550x400mm. |
| 87 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia |
| 88 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 89 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 90 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 91 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms |
| 92 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour 450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms |
| 93 | Providing and fixing PTMT shelf 440 mm long, 124 mm widthand 36 mm height of approved quality and colour, weighing not less than 300gms. |
| 94 | Providing, fixing and laying rigid UPVC pipes conforming to IS:4985 jionting with couplers,of same class conforming to IS :10124(Pt-II)with solvent cement conforming to IS :14182 including testing of jionts complete (but excluding the cost of specials like bend,tees etc.which will be paid separately)as per chapter 20 of CPWD specition and direction of engineer-in-charge A class-3 (working pressure 6.00Kg/cm2 ) Ii) 110 MM OD |
| 95 | Providing,fixing and laying fabricated UPVC bend of required degree conforming to IS 10124(Part 8/9/10/11/12/13) with solvent cement conforming to IS :14182 including testing of jionts complete as per chapter 20 of CPWD specification and direction of the Engineer -in- charge Ii) 110 MM OD |
| 96 | Providing,fixing and laying fabricated UPVC equal teeconforming to IS 10124(Part5) with solvent cement conforming to IS :14182 including testing of jionts complete as per chapter 20 of CPWD specification and direction of the Engineer -in- charge ii) 110x110 mm dia |
| 97 | Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size ) including necessary plaster and pointing in cement mortar 1:4(1cement: 4 coarse sand): 100mmdia. |
| 98 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Internal Work 15 mm dia. nominal bore |
| 99 | 20mm dia. nominal bore |
| 100 | 25mm dia. nominal bore |
| 101 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm dia nominal bore |
| 102 | 25 mm dia nominal bore |
| 103 | 40 mm dia nominal bore |
| 104 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore |
| 105 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore |
| 106 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore |
| 107 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : 15 mm nominal bore |
| 108 | 20 mm nominal bore |
| 109 | 25 mm nominal bore |
| 110 | Providing and fixing gun metal non-return valve of approved quality (screwed end):25 mm nominal bore Vertical |
| 111 | 40 mm nominal bore Vertical |
| 112 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150mm diameter |
| 113 | Constructing masonryChamber 30x30x50 cm, insidewith 75 class designation brick work incement mortar1:5 (1 cement :5 fine sand) forstopcock, withC.I.surface box100x100x75mm (inside)with hingedcover fixedincement concreteslab1:2:4mix (1 cement:2 coarsesand:4gradedstoneaggregate20mmnominalsize) necessary excavation foundationconcrete 1:5:10 ( 1cement :5fine sand:10gradedstoneaggregate40mmnominalsize)andinside plastering with cement mortar 1:3 (1 cement :3 coarsesand) 12mm thick finishedwithafloatingcoatofneatcementcompleteasper standard design : With Second Class bricks |
| 114 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 115 | Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete : 150 mm diameter |
| 116 | Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design: 150 mm diameter S.W, pipe |
| 117 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 118 | Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design : For 500x700 mm size |
| 119 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 120 | Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRD Technical Specification Clause 301.5. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
