|
| 1 | GROUND FLOOR :- Surface dreesing of the ground floor………..as directed |
| 2 | Bailing or pumping out water from foundation trenches…….contractor |
| 3 | Extra over corresponding item of earth…….bucket |
| 4 | Pre Constructional Anti termite measure (a) Anti termite treatment……..1981 |
| 5 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m.as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm |
| 6 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) |
| 7 | Earth work in filling in compound, tank, low land, ditches etc. with good earth, in layers not exceeding 150 mm. including breaking clods and consolidating the same by ramming and dressing complete. (Payment will be made on profile measurement before and after the work) |
| 8 | Filling in foundation trenches or plinths by silver sand in layers not exceeding 150 mm including watering and ramming etc. layer by layer complete. Including cost of sand (Payment to be made on the basis of measurement of finished quantity of work) |
| 9 | Cement concrete with graded stone ballast 40 mm down excluding shuttering in ground floor 1:3:6 propotion |
| 10 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. Rajmahal variety in ground floor. |
| 11 | Hire and labour charges for shuttering and centering including stripping off after completion of work in ground floor(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge |
| 12 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial………...s per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m(i) Tor steel/Mild Steel I.SAIL/ TATA/RINL |
| 13 | 1st class brick work in cement morter 6:1 in foundation and plinth in foundation in ground floor |
| 14 | 1st class brick work in CM 6:1 in super structure ground floor |
| 15 | 125 mm thick brick work in cement morter 4:1 in ground floor |
| 16 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).Using grey cement |
| 17 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (b) Area of each tile upto0.09 Sq. (i) other than Coloured decorative. GR. floor. in floor |
| 18 | Wall - (b) Area of each tile upto0.09 Sq. (i) other than Coloured decorative. GR. floor. |
| 19 | Wood work in Door and window frames fitted and fixed complete. (c) Sal : Local |
| 20 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos ofscrews to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as peranufacturer?s specification and direction of Engineer-in-Charge. |
| 21 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made |
| 22 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top &bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. In ground floor. |
| 23 | Supplying fitting fixing M S Clamp 40 mm x 6 mm, 250 mm |
| 24 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISImark.viii) 100mm. X 75mm. X 3.50mm. |
| 25 | Iron socket bolt of approved quality fitted and fixed complete. |
| 26 | Brass hasp bolt of approved quality fitted and fixed complete (oxidised) with16mm dia rod with centre bolt and round fittingc) 300mm long |
| 27 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete(vi) 150 mm grip x 10 mm dia rod. |
| 28 | MS or WI ornamental grill of approved design joints continously welded with MS, WI flat bars for windows railing etc. fitted and fixed with necessary lugs and screws(i) Grill weighting above16 Kg/Sq.Mtr. Gr. Floor. |
| 29 | For Main Gate |
| 30 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar…….i) With 1:6 cement mortarb) 20 mm thick plaster |
| 31 | c) 15 mm thick plaster |
| 32 | Neat Cement running about 1.5 mm average thick in wall, dado, window, sills, floor drain etc. in all floors in ground floor |
| 33 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar…….i) With 1:4 cement mortarb) 10 mm thick plaster |
| 34 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc on steel surface |
| 35 | (b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc on wooden surface |
| 36 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening …….., if necessary:(a) On timber or plastered surface (ii) Two coats (white in shade |
| 37 | (B) On Steel or other metal Surface |
| 38 | Supplying best indian sheet glass set in putty and fitted fixed with nails and putty complete 5 mm thick. Gr. Floor. |
| 39 | Applying Acrylic Emulsion paint of approved make and brand on walls and ceiling including sand papering...... Putty. (Two coats)ii Luxon Quality |
| 40 | S/F/F cast iron down pipes confroming to IS:- 3989-1970 and IS-1729-1964 in position with necessary clamps, nails includingmaking hole in wall.................. With joining materils cmplete (iii) 150mm dia |
| 41 | C.I. Shoe of down pipe (iii) 150mm dia |
| 42 | 150 mm dia |
| 43 | Supplying fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, Union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cort of all necessary fittings as required, joining materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No seperate payment will be made for accessories, specials.)(Item no. 1 )(A) For EXPOSED WORK:- a)15 mm dia, Medium Quality. |
| 44 | b)20 mm dia, Medium Quality. |
| 45 | C)25 mm dia, Medium Quality. |
| 46 | (B) For Concealed WORK:-a)15 mm dia, Medium Quality. |
| 47 | b)20 mm dia, Medium Quality. |
| 48 | C)25 mm dia, Medium Quality. |
| 49 | Supplying fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg. per sqm. ( for water line only ) |
| 50 | S/F/F C.P.bib cock/ stop cock. i) Chromium plated Bib Cock short body ( Equivalent to code No.511& Model-Tropical/Sumthing special of ESSCO or similar brand ) |
| 51 | Supplying, fitting, fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C.fittings complete,C.I. brackets including two coats of painting to brackets etc. |
| 52 | Supplying P.V.C. Water storage tank of approved with closed top with Lid(Black) Multilayer, (d) 2000 litre capacity |
| 53 | S/F/F cast Iron raised rain proof tank cover 450mm |
| 54 | Labour for hoisting plastic water storage tank (ii) Avobe 1500 litre upto 5000 litre capacity(a)Upto 1st story from G.L. |
| 55 | Labour for puncing hole in plastice water water storage tank upto- 50mm dis |
| 56 | Supplying, fitting, fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm. x75 mm. wooden blocks, C.P.waste fittings of 32 mm. dia,one approved quality brass C.P. pillar cock of 15 mm. dia C.P.chain with rubber plug of 30 mm. dia ,approved quality P.V.C. waste pipe with C.P.nut 32 mm. dia.,900 mm. long approved quality P.V.C. connection pipe with heavy brass C.P.nut including mending good all damages and painting the brackets with two coats of approved paint. |
| 57 | S/F/ F aproved approved brand P.V.C Connector white flexible with both ends coupling with heavy brass C.P. Nut, 15 mm dia (III) 600 mm long |
| 58 | S/F/ F aproved brand 32 mm dia P.V.C. Waste pipe, with PVC coupling at one end fitted with necessary clamps |
| 59 | S/F/F Cast iron soil pipe only conforming to I.S. 3989/ 2009 and I.S.1729/2002 with bobbins, nails etc............................................ Specials , payment for specials & paintng will however be paid separately. (With valamoid joints includind sealing with sand cemen morer(4:1) upto quater depth (i) 150 mm dia ( internal) |
| 60 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing). |
| 61 | Supplying , fitting and fixing Flat back Urinal (Half stall Urinal ) in white vitreous chinaware of approved make supplied,fitted and fixed in position with brass screw on 75 mm x 75 mm x 75 mm wooden block complete |
| 62 | S/F/F Urinal flush pipe fittings of app. Band (a) C.P. Urinal flush pipe fittings range of one |
| 63 | S/F/F 18mm thick marble partition slab with chawk doongri marbel............ Edges polished |
| 64 | S/F/F belelled edged mirror 505 mm thick silver red as....... C.p. Hinge |
| 65 | s/f/f liquid soap container(d0 Polythene |
| 66 | Construction of Inspect Pit of inside measurement 600 mm X 600 mm X upto 600 mm (depth)with 250 mm thick at 1st class brick work in cement mortar (6:1) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (6:3:1) with jhama khoa over a layer of jhama brick flat soling, 12 mm thick (4:1) cement plaster to insidewalls and out-side walls upto GL and 20 mm thick (4:1) plaster to bottom of the pit, providing necessary invert with cement concrete (4:2:1) with jhama chips as per direction, neat cement finishing to entire internal surfaces, top of the pit cover with 100 mm thick RCC slab (4:2:1) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (4:1) in all external surface of the slab & ne 560 mm dia RCC manhole cover of approved makes supplied fitted & fixed in the slab with necessary fitings, necessary earth work in excavation in all sorts of soil, filling sides of pit with earth and removing spoils after work complete in all respect. with pakur variety |
| 67 | Construction of septic tank of different capacities as per approved drawing with Ist class brick work in cement mortar (4:1) including two 560 mm dia RCC manhole cover of approved make supplied, fitted and fixed in the top slab with necessary fittings, 19 mm thick cement plaster (4:1) with neat cement finish to the internal surfaces and 12 mm thick cement plaster (4:1) to outside wall upto 200 mm below GL floor finished with 25 mm hick grey artificial stone including supplying, fittings and fixing all necessary specials, fittings, SW tees, CI foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, filling up the chabmer with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring to be done with admixture of water proofing compound @ 5% by weight of cement, complete in all respect as per directionof Engineer-in-charge./ Otherr than TATA /SAIL/ RINL |
| 68 | Construction of circular soak well 2.5 metre deep in all types of sandy soil with dry brick work upto 1.6 metre from the bottom having150 mm intermediate cement brick work (6:1) band all around and cement brick work (6:1) upto 0.90 metre from top with 19 mm thick cement plastering (4:1) to inside face upto the depth of cement brick work, 12 mm thick cement plaster (4:1) on outer face from top of the wall upto GL and 6 mm thick cement plaster (4:1) on top of the RCC cover slab including filling bottom 1.00 metre of inside of the well with brick metal ( 50 mm to 63 mm size) including RCC cover slab of designed thickness with cement Concrete (4:2:1) with stone chips with necessary reinforcement and shuttering including one 560 mm dia RCC manhole cover of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making necessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the excess eatth from the premises as per direction complete in all respect with all costs of labour & materials.With 250 mm. thick dry brick work and 250 mm. thick cement brick work (6:1) and 1.00 metre inside dia. |
| 69 | Brick workwith 1st class bricks in cemen mortar (1:4)(a) IN foundation and plinth |
| 70 | FIRST FLOOR:- Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. Rajmahal variety in ground floor. |
| 71 | Hire and labour charges for shuttering and centering including stripping off after completion of work in ground floor(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge |
| 72 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial………...s per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m(i) Tor steel/Mild Steel I. |
| 73 | Brick workwith 1st class bricks in cemen mortar (1:6)(a) Insuperstructure , G.F |
| 74 | 125 mm thick brick work in cement morter 4:1 in ground floor |
| 75 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (asnecessary) and marble dust in proportion (1:2) including smooth finishing and roun |
| 76 | Supplying, fitting fixing of 1st quality Ceramic tiles of any size having mat finish in walls and floors including borders to match with the existing work, set in sand cement mortar (4:1) & 1 : 6 in wall & floor respectively including backing concrete (1:2:4) & 4 nos of key stones (10 mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide of required to match colour of tiles.a ) With Sand Cement Mortar (1:4) 20 mm thick & 2 mm. thick cement slurry at the back side of tiles using [email protected] kg/sqm. & joint filling using white cement slurry @ 0.20 kg/sqm.in Ground Floori )Area of each tiles upto 0.09 sqm./ Colour decorative |
| 77 | ii) In Wall |
| 78 | Wood work in Door and window frames fitted and fixed complete. (c) Sal : Local |
| 79 | S/F/F factory made P.V.C. door frame of size 50 mm x47 mm with a wall thickness of 5 mm…………….. E.i.c. (a) Door frame |
| 80 | Panel shutters of door and window, as per design (each panel consisting of singleplank without joint), including fitting and fixing the same in position butexcluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single |
| 81 | S/F/F factory made 30 mm thick Factory made solid panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness…………………………………….. E.I.C. In Ground Floor |
| 82 | S/f/F M.S. Clamps for door & Window frame made of flat bent bar……….. Cement concrete (1:2:4) as per direction |
| 83 | Ironbutt hinges of approved quality fitted & fixed with steel screws with ISI mark in position, complete.100 mm X 75 mm X 3.50 mm. |
| 84 | Iron socket bolt of approved quality fitted and fixed complete. |
| 85 | Brass hasp bolt of approved quality fitted and fixed complete (oxidised) with16mm dia rod with centre bolt and round fittingc) 300mm long |
| 86 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete(vi) 150 mm grip x 10 mm dia rod. |
| 87 | M.S. or W. I. ornamental grill of approved design joints continuously welded with M.S., W.I. flats andbars for windows,railing etc fitted & fixed with necessary screws and lugs.in Ground Floor i ) Grill weighing 10 to 16 kg./ Sqm. |
| 88 | Plaster ( to wall, floor , ceiling etc. ) with sand cement mortar including Rounding off or chamfering corners as directed and racking out joints or roughening of concrete surface, including threading nosing and drip Course where necessary. |
| 89 | (b) 15 mm thick Plaster |
| 90 | Neat Cement running about 1.5 mm average thick in wall, dado, window, sills, floor drain etc. in all floors in ground floor |
| 91 | Plaster ( to wall, floor , ceiling etc. ) with sand cement mortar including Rounding off or chamfering corners as directed and racking out joints or roughening of concrete surface, including threading nosing and drip Course where necessary. |
| 92 | Priming one coat onsteel or other metal surface with synthetic enamel / oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 93 | B) Priming one coat on timber, plastered or on steel or other metal surface with synthetic enamel / oil bound primer of approved quality including smoothening surfaces by sand papering etc. . |
| 94 | Painting with best quality Synthetic Enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc on the surface if necessary. |
| 95 | B) On steel or Other metal surface |
| 96 | Supplying best indian sheet glass set in putty and fitted fixed with nails and putty complete 5 mm thick. Gr. Floor. |
| 97 | Applying Acrylic Emulsion paint of approved make and brand on walls and ceiling including sand papering...... Putty. (Two coats)ii Luxon Quality |
| 98 | SECOND FLOOR:-Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. Rajmahal variety in ground floor. |
| 99 | Hire and labour charges for shuttering and centering including stripping off after completion of work in ground floor(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge |
| 100 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial………...s per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m(i) Tor steel/Mild Steel I. |
| 101 | Supply fitting fixing Zn Al alloy in roof |
| 102 | Brick workwith 1st class bricks in cemen mortar (1:6)(a) Insuperstructure , G.F |
| 103 | Wood work in Door and window frames fitted and fixed complete. (c) Sal : Local |
| 104 | Panelshutters of door and Window as per design (each panel consisting of single plank without joint) IN G.F |
| 105 | Plaster ( to wall, floor , ceiling etc. ) with sand cement mortar including Rounding off or chamfering corners as directed and racking out joints or roughening of concrete surface, including threading nosing and drip Course where necessary. |
| 106 | B) 15 mm thick Plaster |
| 107 | M.S. structural works in roof thickness with tubular section………….. etc |
| 108 | Priming one coat on timber, plastered or on steel or other metal surface with synthetic enamel / oil bound primer of approved quality including smoothening surfaces by sand papering etc. . |
| 109 | Painting with best quality Synthetic Enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc on the surface if necessary. |
| 110 | Applying Acrylic Emulsion paint of approved make and brand on walls and ceiling including sand papering...... Putty. (Two coats)ii Luxon Quality |
| 111 | SUBMERSIBLE PUMP:Labour for boring tube well of required dia. by water jet system through any type of soil strata including hire and labour charges for boring pipes, scaffolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other incidental works in the connection. The tube well should have a minimum 50 mm gap in between the outside of the tubewell pipe and the boreii) 50 mm dia. boring etc. |
| 112 | ii) 100 mm dia. boring etc |
| 113 | Supplying, fitting and fixing steel cutter piece upto 450 mm long with sockets.ii) 50 mm dia |
| 114 | Supplying PVC strainer of approved make with adapter conforming to I.S.12818 specifications.ii) 50 mm dia |
| 115 | Supplying, fitting and fixing G.I. cap at top(i) 100 mm |
| 116 | Supplying, fitting and fixing heavy type bell mouth reducing socket. (i) 50 mm X 100 mm |
| 117 | Supplying, fitting and fixing PVC pipes for underground work of……... payment will be made for accessories, specials.) PVC PipeI) 50 mm Dia |
| 118 | I) 100 mm Dia |
| 119 | Packing the annular space between the outside of the tube well pipes & strainers and the bore with pea size washed gravel of approved quality having size from 2 mm to 5 mm or the size approved by the Engineer-in charge including cost of all materials labour and equipment complet |
| 120 | Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with \"V\" notch including hire and labour charges for all tools and plants and scaffolding as required. |
| 121 | Supply & Delivery of 415 volt 3 phase 5 HP submersible pump motor set with having outlet size 50 mm ( plake-KSB) model no-caro 100 12c/17+370/22-UMI100) |
| 122 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80….. specials. Payment for painting willbe made seperately) (a) For Exposed WorkPVC Pipesi) 32 mmDia |
| 123 | ii) 25 mm Dia |
| 124 | Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction. |
| 125 | Sub Total |
| 126 | GST 12% |
| 127 | CESS 1% |
