|
| 1 | SURF BOARDProviding, and fixing of Surf Board of size910mm (Length) x 860mm (Width) x 1400mm.(Height) fabricated with a center pipe of 100mm Nominal Bore shall be made from “c” class G.I. pipe. The sleeve pipe shall be made of 125mm OD seamless pipe with thickness of 5mm and bolted to main frame with M10 SS bolts. The bottom support shall be welded of M.S. plate of Ø 250 mm & 10mm thickness. The handle frame of 25NB shall be made from “c” class G.I. pipe The paddle frame of 50NB shall be made from “c” class G.I. pipesupported with 70X8mm bend M.S. flat and can be replaceable. The foundation to be used for fixing should be a structure and shall be made from center pipe of G.I. of 80NB “c” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Bushes shall be used of 70mm Outer Diameter with 5mm thickness. The footrests shall be made from Aluminum casting material of size 320mm X270mm X5mm. For support to footrest of 200mmX250mm with 3mm thickness M.S. Plate shall be used. Closing Capsshall be made up of high quality Fiber reinforced Plastic material. The pins to be used shall be made up of Ø35 mm SAE 8620 bright material. The bearing shall be used are of “6007zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nut bolts shall be used for assembly. The cerclips shall be used for assembly of A34.The powder coating shall be done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. |
| 2 | CROSS TRAINERProviding and fixing of Cross trainer of size 1320mm (Length) x 600mm (Width) x 1750mm. (Height) fabricated with the main frame Pipes of 80NB shall be made of “C” Class G.I and pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The Handle Frame shall be made up of 25NB “C” Class G.I. Pipe. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. pipeof 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe should be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm and CRC square pipes of 3mm thickness.To build structure bushes to be used which shall be made from M.S.seamless pipe of 60mm OD with 5 mm thickness. The footrests shall be made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick.Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 35mm, 25mm, and 17mm shall be made up from SAE 8620 bright . The Bearings shall be usedof “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 Micron thickness. A16 , A 24 mm circlips shall be used for assembly. Bolt M8X16 mm and NY lock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 3 | SEATED PULLERProviding and fixing of Seated Puller of size 1900mm (Length) x 740mm (Width) x 1920mm. (Height) fabricated with a center pipe is of 100NB shall be made from “C” Class G.I. pipe. Bottom support of M.S. round plate of Ø 250 mm & 10mm thickness shall be welded. All linkages shall be made up of 25NB “C” class G.I. pipe. The handle frame of 32NB “C” class G.I. pipe. The seat frame of 32NB “C” class G.I. pipe, To build structure bushes to be used which shall be made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap shall be made from FRP Material. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. The bearings shall be used of “ 6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for assembly are of A16 The powder coating shall be done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 4 | CHEST PRESSProviding and fixing of Chest Press of size 2000mm (Length) x 710mm (Width) x 2200mm. (Height) fabricated with the center pipe of 100NB shall be made up of “C” Class G.I. pipe. The bottom shall be welded with support of M.S. round plate of Ø250 mm & 10mm thickness. The connecting pipes shall be made up from 25NB “C” class G.I. pipe. The handle frame shall be made up from 32NB “C” class G.I. pipe. To build structure bushes to be used which shall be made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush shall be used. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests to be fitted on the outer frames shall bemade up of M.S. Sheet of size 330mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap shall be made from FRP Material with 0.7 thickness. Pins to be used of Diameter 25mm and 17mm shall be made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings shall be used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The cerclips to be used for locking shall be made up of A24 mm & A16mm. The powder coating shall be done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. |
| 5 | SEATING & STANDING TWISTERProviding and fixing of Seating & Standing Twister of size 1700mm (Length) x 540mm (Width) x 1250mm. (Height) fabricated with a Center Pipe of 100mm NB shall be made from “C” Class G.I. Round Pipe. The M.S. round plate of Ø250 mm & 10mm thickness shall be welded at bottom. Handle and Bottom sleeve pipe of 125mm OD with thickness 5mmshould be provided for easy assembly, replacement and maintenance. The bottom frame of the Seating & Standing twister of 32 NB, 50 NB, and 25 NBshall be made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe of 25mm NB. The foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe shall be supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. The Pins to be used which shall be made up of Ø 35 mm SAE 8620 bright material. The bearings shall be made of of “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc |
| 6 | CHEST CUM SHOULDER PRESSProviding and fixing of Chest Press cum seated puller of size not less than 2000mm (Length) x 710mm (Width) x 2250mm. (Height) to enhance the strenth of upper limbs and the muscles in chest and shoulder. The main structure frame shall be made from G.I. pipe minimum of 80Nb\"C\" class welded with M.S. round base plate atleast 250mm &10mm thick.The seats and Back rests to be fitted on the outer frames shall be made up of minimum of M.S.sheet of size 330mmx300mmx2mm thickness. Closing caps shall be made up of high quality fiber reinforced plastic material.High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of Engineer-in-charge to fullfill the functional requirement.The indicative design photo is as per enclosed photo no.11((The cement concrete and excavation work shall be paid seperately) |
| 7 | Thai-Chispinner(2 Wheel) Providing and fixing of Thai-Chispinner(2 Wheel) of size not less than 700mm(Length)x1000mm(Width)x1280mm.(Heigth),to increase the mobility og shoulder elbow and hip knee.The main structure frame shall be made from G.I.pipe minimum of 80N\"C\" class welded with M.S. round base plate atleast 0250mm & 10mm thick .High tensile S.S.nut bolt shall be used for assembly.The powder coating shall be done with pure polyster powders of Ackzonoble/Berger/Nerolac with minimum 60 to 70 micron thickness,complete in all respect including fixing the M.S. holdfast in cement conctrete to hold the whole structure under the direction of engineer-in-charge to fullfill the functional requirement.(The cement concrete and excavation work shall be paid seperately.) |
| 8 | (LEG PRESS) Providing and fixing of Leg Press of size not less than 1840mm(Length)x360mm(Width)x1560mm.(Heigth),to build up the muscle of thigh and enhance the strength of waist.The main structure frame shall be made from G.I.pipe minimum of 80N\"C\" class welded with M.S. round base plate atleast 0250mm & 10mm thick .The sleeve frame minimum of 1000 D and of M.S.seamless pipe with thickness 5 mm.This sleeve should be disassembles from main frame.The footrests shall be made from casted aluminium material having size minimum of 130 mmx310mmx5mm thick.Closing caps shall be made up of high quality fibre reinforced plastic material .High tensile steel galvanizednut bolt shall be used for assembly.The powder coating shall be done with pure polyster powders of Ackzonoble/Berger/Nerolac with minimum 60 to 70 micron thickness,complete in all respect including fixing the M.S. holdfast in cement conctrete to hold the whole structure under the direction of engineer-in-charge to fullfill the functional requirement.(The cement concrete and excavation work shall be paid seperately.) |
| 9 | Excavation including loading, unloading, disposal and dressing of excavated earth within initial lead of 50m and lift up to 1.5m in dry or moist including dressing of excavated area, dewatering wherever required complete in all respect(A) Hard soil mix with kankar/ boulders, morrumITEM NO .1 C (V) BSR WRD alwar 2020 |
| 10 | ?????? ??????? 1 ?????? : 4 ???? ??? 8 ?????? / 1 ??????, 3 ???? ???6 ?????? ?????? ?? 40 ???? ????? ??? ?? ???? ??? ?????,????? ??? ???? ??? ????? item no. 15 a bsr ps Kathumar-2021 |
| 11 | ?????? ???????1 ?????? : 2 ???? : 4 ?????? ???????? ?????? ??? 12 ???? ????? ??? ?? ???????? ?? ??? ?????,????? ??? ???? ??? ???? item no. 16bsrps kathumar- 2021 |
| 12 | Board and photo |
