|
| 1 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains in earth work in all heights anddepth in all kinds of soils, including saturated soil comprising of pick work, jumper work, and blasting work both in soft and hard rock with chisellingand wedging out of rock (where blasting is prohibited) andtheir intermediate classificationof soilsincluding, dewatering wherever required, settingout to required lines,levels as shown on the drawing and as directed by the Engineer -in-Charge at site and sorting out useful and un- useful material and transportation of the un -useful material for disposing at approved dumping site or otherwise and including payment of prescribed charges of dumping to the owner of dumping site (to be arranged by the contractor) for the satisfaction of Engineer- in -Charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and other incidentals necessary to complete the work by mechanical means and labour (if required) including disposal of all surplus excavated earth at approved dumping site including all leads and lifts. |
| 2 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing as directed by the Engineer-In charge complete including carriage of materials within all leads and lifts. |
| 3 | Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30mm x 30mm x 5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 5 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work including carriage of materials in all leads and lift as per direction of Engineer in Charge:- |
| 4 | Foundations, footings, bases of columns, etc. for mass concrete |
| 5 | Suspended floors, roofs, landings, balconies and access platform |
| 6 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 7 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 8 | Stairs, (excluding landings) except spiral-staircases |
| 9 | Edges of slabs and break in floors and walls :-i)Under 20cm wide |
| 10 | Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards |
| 11 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 12 | Providing and laying in position cement concrete 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)of specified grade excluding the cost of centering and shuttering including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 13 | Providing and laying cementconcrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)in retaining walls, return walls, walls(anythickness)includingattachedpilasters,columns,piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor all level, excluding the cost of centering, shuttering and finishing:as directed by the Engineer-In charge complete including carriage of materials within all leads and lifts. |
| 14 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) as directed by the Engineer-In charge complete including carriage of materials within all leads and lifts. |
| 15 | Providing and laying in position reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) mechanically mixed and vibrated of specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level completeincluding carriage of materials in all leads and lifts as per direction of Engineer in Charge. in foundationfootings, bases of columns and the like and mass concrete. |
| 16 | Providing and laying in position Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size) work mechanically mixed and vibrated in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 17 | Providing and laying in position Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)work mechanically mixed and vibrated in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to all floor level, excluding cost of centering, shuttering, finishing and reinforcement complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 18 | Providing and laying in position steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. and other works including straightening, cutting, bending, placing in position and binding all complete for all levels complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 19 | Providing and laying Coursed rubble masonry (first sort) with hard stone in foundation and plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 20 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Cement mortar 1:6 (1 cement : 6 coarse sand) in superstructure for all floor levels in all shapes and sizesincluding carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 21 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 with Cement mortar 1:4 (1 cement :4 coarse sand) in superstructure for all floor levelsincluding carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 22 | Providing and laying Soling Stone under floors properly hand packed filling interstices with spalls and consolidating including spreading water complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 23 | Providing weep holes in brick masonry/stone masonry/plain concrete / reinfoced concrete , abutment,wing walls with 110mm dia PVC pipe extending through the full length with of the structure with the slope of I (V) : 20 (H) towards drawing face complete as per drawings and MORD technical specifications clause 614, 709, 1204.3.7 oras directed bytheEngineer-in-Charge, including carriageof materials within all leads and lifts . |
| 24 | Providing and fixing glass panes with putty and glazing clips in steel / wooden doors, windows, clerestory windows, all complete with 5.00mm thick glass panes completeincluding carriage of materials within all leads and liftsas directed bytheEngineer-in-Charge. |
| 25 | Providing and fixing 35mm thick wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws complete including carriage of material within all leads and lifts as per direction of Engineer-in-charge in 2nd class deodar wood. |
| 26 | Providing and fixing 19mm thick water proof commercial kit ply (gold) or equivalent board in Shutter for cupboardincluding fixing with nickel plated piano Hinges with screw etc complete including carriage of material within all lead and lift as per direction of Engineer in charge. |
| 27 | Providing and fixing 6mm thick waterproof plywood kit ply gold or equivalent in lining with butt jointing including mitring at junctions and nails etc complete ( framework for ways to be measured and paid for separately) including carriage of materials in all leads and lift as per direction of Engineer in Charge.. |
| 28 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes fixed required size of beading, including ISI marked M.S. pressed butt hinges of required sizeswith necessary screws including carriage of materials in all leads and lifts:-Firstclass Deodar wood 35mm thick. |
| 29 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:- 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 30 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding or by screws including carriage of materials in all leads and lifts. |
| 31 | Providing and fixing cromium plated sliding door bolt with nuts and screw etc complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 32 | 300 X 16 mm size |
| 33 | 250 X 16 mm size. |
| 34 | Providing and fixingaluminiumtower bolts (Barrel type) anodized complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge:- |
| 35 | 250 X 10 mm size |
| 36 | 200 X 10 mm size. |
| 37 | Providing and fixingaluminium handles anodized complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge:- |
| 38 | 125 mm size |
| 39 | 75 mm size. |
| 40 | Providing and fixing oxidized single acting Door springwith necessary screws etc.complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge:- 150mm. |
| 41 | Providing and fixing oxidized M.S. hasps and stapple for cup board 90 mm sizecomplete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 42 | Providing and fixing 150mm (one hundred fifty milimetre) oxidized M.S. hooks and eyes complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 43 | Providingand fixing Hard wood plain squre edged cover fillets beeding19 x 6mm section including mitring at junction with wooden screws and nails etc. completeincluding carriage of materials in all leads and lifts:- |
| 44 | Providing and fixing 1 mm thick lamination sheet of approved shade and quality fixed with approved adhesive and nails complete including carriage of material within all leads and lifts. |
| 45 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc.complete including carriage of material within all leads and lifts:-.Double strip (horizontal type). |
| 46 | Providing 40x5 mm flat iron hold fast 40cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) including carriage of material within all leads and lifts. |
| 47 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated bracketsincluding carriage of material within all leads and lifts.: |
| 48 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc.complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 49 | Providing and laying vitrified floor tiles of 600mm X 600mm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 50 | Providing and laying Vitrified tiles of 300mm x300mm sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc.complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 51 | Providing and laying rectified Glazed Ceramic floor tiles of size 300mm x 300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. . |
| 52 | Marble stone flooring with 18mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete completeincluding carriage of materials in all leads and lift as per direction of Engineer in Charge:- Black Zebra. |
| 53 | Providing and layingceremic tiles 300mm x 450mm, 300mm x 600mmand 200mm X 300mmIst quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 54 | Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading completeincluding carriage of materials in all leads and lift as per direction of Engineer in Charge |
| 55 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 56 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) including carriage of materials in all leads and lift as per direction of Engineer in Charge |
| 57 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwsincluding carriage of materials in all leads and lift as per direction of Engineer in Charge:- Crimp curve |
| 58 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Gutter (600 mm over all girth) |
| 59 | Providing and fixing M.S. B.P Sheet 2.00mm (two milimetre) thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid for separtely) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 60 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionincluding carriage of materials in all leads and lift as per direction of Engineer in Charge. , (i) Single socketed pipes. 110 mm diameter |
| 61 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionincluding carriage of materials in all leads and lift as per direction of Engineer in Charge. . |
| 62 | PVC Door bend 110 mm |
| 63 | PVC Plain Shoe 110 mm |
| 64 | PVC collar110 mm |
| 65 | Providing and fixing 110 mm unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 66 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:- |
| 67 | Door and Window Frames and shutters. |
| 68 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 69 | Staircase and Verandah Railing of Hollow sections. |
| 70 | Finishing with Deluxe Multi surface paint system for interiors and exteriors with Two or more coat applied @ 0.90 liters/ 10 square metre over an under coat of primer applied @ 0.80 liters// 10square metreof approved brand and manufacture using Primer as per manufacturers specifications. Painting Steel work with Deluxe Multi Surface Paint to give an even shade complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 71 | Polishing two or more coats with PU polish of required shade on New wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler including carriage of materials in all leads and lifts. |
| 72 | 6mm thick cement plaster of mix 1:3 (1 cement : 3 fine sand) in ceiling upto all floor level including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 73 | 15mm cement plaster in single coat on fair side of brick/ concrete/ stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth. in Cement Mortar 1:6(1 cement:6 sand) complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 74 | 15mm (Fifteen milimetres) thick cement plasters in single coat on rough side of brick / concrete / stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) within all leads, lifts of materials and other incidentals. |
| 75 | 15mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 76 | Distempering with oil bound washable distemper on wall/ ceiling of approved brand and manufacture to give an even shade, New work (two or more coats) over and including water thinnable priming coat with cement primer complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 77 | Finishing walls with water proofing cement paint of required shadeNew work (Two or more coats applied @ 3.84 kg/10 sqm) and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth completeincluding carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 78 | Finishing walls with satin enamel paint of required shadeNew work (Two or more coats applied @ 3.84 kg/10 sqm) and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 79 | Wall / ceiling painting with acrylic emulsion paint of approved brand and manufacture to give an even shade, Two or more coats on new work complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 80 | Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall/ ceiling surface to prepare the surface even and smooth complete including carriage of materials in all leads and lift as per direction of Engineer in Charge. |
| 81 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 82 | Providing and laying 80 mm thick factory made cement concrete interlocking paver block of M -30 grade of NTC make or equivalent made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:- |
| 83 | Providing and fixing Bamboo jaffery / fencing consisting of superior quality 25 mm dia (Average) half cut bamboo placed vertically and fixed together with three numbers horizontal running members of hollock wood in scantling of section 50mmX25 mm, fixed with nails and G.I wire on existing support complete as per direction of Engineer-in-chargeincluding carriage of materials in all leads and lifts. |
| 84 | Providing and fixingHA Wall-Mounted Activity Mirror with Flat Polished Edge, Home Gym Mirror Beveled Activity Workout Room Wall Mirror for Fitness, Dancing, Gymnastics, Yoga Horizontally or Verticallymirror of wall size of superior glass (of approved quality) complete with all leads and lift as per direction of engineer-in-chargeincluding carriage of materials in all leads and lifts. |
| 85 | Epoxy Marking on Tennis Court for marking cout lines complete as per direction of Engineer in Incharge including carriage of materials in all leads and lifts. |
| 86 | Rexcourt / taraflex flooring (L.G. Make or its equivalent) plain, coloured. corbed or mosaic or mattled finish, laid with approved adhesive on sub floor damp proofing treetment(to be measured separately)for payment including carriage of materials within all leads and lifts. |
| 87 | Providing and installing app. 1000kg in weights for Gym to school which includes in as per direction of Engineer-in-charge including carriage of materials within all leads and lifts:- Pully machine cum pull up bar.Incline, decline and flat benches Benches for curls.Leg extension machine:-Equipment for free weights like different grips, bars etc.including carriage of materials within all leads and lifts. |
| 88 | Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing.This includes the cost of cutting chases and including testing of joints complete including carriage of materials in all leads and lift as per direction of Engineer in Charge:- |
| 89 | 1216 (16 mm O.D. pipe) |
| 90 | 1620 (20 mm OD pipe) |
| 91 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including fittings like tank nipples, ball cock etc excluding base support for tank complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.:- 2000 litres net capacity tank. |
| 92 | Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately)including carriage of materials in all leads and lift as per direction of Engineer in Charge:- 15 mm nominal bore. |
| 93 | Providing and fixing on wall face unplasticised Rigid PVCpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage of materials in all leads and lift as per direction of Engineer in Charge.: |
| 94 | 75 mm diameter |
| 95 | 110 mm diameter |
| 96 | Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of materials in all leads and lift as per direction of Engineer in Charge.: |
| 97 | 75 mm diameter |
| 98 | 110 mm diameter |
| 99 | Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVCpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionincluding carriage of materials in all leads and lift as per direction of Engineer in Charge:- |
| 100 | PVC door bend with oval access door, insertion rubber washer ISI marked 75 mm nominal size. |
| 101 | PVC door bend with oval access door, insertion rubber washer ISI marked 110 mm nominal size. |
| 102 | PVC (finolex) plain bend ISI marked75 mm nominal size :- |
| 103 | PVC (finolex) plain bend ISI marked 110 mmnominal size :- |
| 104 | PVC single equal Tee with door, ISI marked insertion rubber washer 75 mmnominal size :- |
| 105 | PVC single equal Tee with door, ISI marked insertion rubber washer 110 mmnominal size. |
| 106 | PVC single equalplain Tee ofISI marked 75 mmnominal size. |
| 107 | PVC single equalplain Tee ofISI marked 110 mmnominal size. |
| 108 | PVCcollars ISI marked 75 mmnominal size :- |
| 109 | PVCcollars ISI marked 110 mmnominal size :- |
| 110 | PVCcowl ISI marked110 mmnominal size :- |
| 111 | Providing and fixing110 mm X 75 mm size PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials within all leads and lifts. |
| 112 | Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. with integral \"P\" or \"S\" trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1 sand) seat and cover to be measured and paid for separately including carriage of materials within all leads and lifts :-European type/ wash down type water closet pan. |
| 113 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity including carriage of materials within all leads and lifts: - White. |
| 114 | Providing and fixing 630mmx450mm flat back vitreous China wash basin with single hole for pillar tap with C.I. or M.S.brackets painted white including cutting holes and making good the same but excluding fittings including carriage of materials within all leads and lifts. |
| 115 | Providing and fixing C.P. Waste Coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms for wash basin and sink, of approved quality and colour including carriage of materials within all leads and lifts |
| 116 | Providing and fixing 32 mm dia, PVC waste pipe for wash basin or sink includingcheck nut including carrage of material within all leads and lifts. |
| 117 | Providing and fixing 100mm dia, C.P. grating including carrage of material within all leads and lifts. |
| 118 | Providing and fixing 600mm x 450mm beveled edgemirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete including carriage of materials within all leads and lifts. |
| 119 | Providing and fixing PTMT towel rail complete with brackets fixed to woodencleatswithCPbrassscrewswithconcealedfittings arrangement of approved quality and colour complete including carriage of materials within all leads and lifts :- 600 mm long towel rail with total length of 645mm, width 78mm and effective height of 88 mm, weighing not less than 190 gms. |
| 120 | Providing and fixing 15mm dia C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gmscomplete including carriage of materials within all leads and lifts. |
| 121 | Providing and fixing 15mm dia CP brasspillar tapwith capstan head including carriage of materials within all leads and lifts. |
| 122 | Providing and fixing 15mm dia C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 including carriage of materials within all leads and lifts. |
| 123 | Providing and fixing 45cms length PVC connection pipe with union including carriage of materials within all leads and lifts :- 15mm nominal bore. |
| 124 | Providing and fixing 15mm nominal bore brass Ball valve with wheel including carriage of materials within all leads and lifts. |
| 125 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionincluding carriage of materials within all leads and lifts:- Single socketed pipes:- 150mm dia. |
| 126 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90cm x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internaldimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : Withcommon burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete including carriage of materials within all leads and lifts. |
| 127 | Providing and fixing C.P. brass toilet paper holder complete, fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts. |
| 128 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms including carriage of materials within all leads and lifts. |
| 129 | Supplying and fixing 300mm X 300mm precast RCC cover with frame for gully trap complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 130 | Providing and fixing 455mm X 610mmprecast reinforced cement concrete cover with frame for manholes complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
