Public Works Department-PWD has published Strengthening Of Veterinary Health Care Infustructure Through Construction Of Veterinary Sub Centre At Bishram Bari Under Mandwi Block During The Year 2021 22 Sh Construction Of Building, Shed For Animal, Electrification And Water Supply Facility. Stren. Submission Date for this Tender is 08-02-2022. Building Work Tenders in jirania Tripura. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | BUILDING PORTION A)SUB-HEAD : EARTH WORK 1). Earth work in excavation by mechanical means(Hydralic exvator)/ manual in foundation trenches or drains (not exceeding 1.5 m, in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (i) All kinds of soil. |
| 2 | 2) Filling available excavated earth(excluding rock) in ternches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. (i) All kinds of soil. |
| 3 | 3) Supplying and filling in plinth, under floor, foundations etc. with sand(fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or any suitable method complete. |
| 4 | B)SUB-HEAD : CEMENT CONCRETE WORK 4) Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level: a)1:4:8 (1 Cement : 4 fine sand : 8 Graded stone aggregate 40 mm nominal size) |
| 5 | b)1:3:6 ( 1 Cement:3 fine sand : 6 Graded stone aggregate 20 mm nominal size) |
| 6 | c) 1:2:4 ( 1 Cement:2fine sand : 4 Graded stone aggregate 20 mm nominal size) |
| 7 | 5) Making plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 cement: 3 fine sand: 6 Graded well burnt brick aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 8 | C)SUB-HEAD : RCC WORK 6) Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttaring, finishing and reinforcement -All work upto plinth level. a)1: 1 ½ :3 ( 1 Cement: 1 ½ fine sand: 3 Graded stone aggregate 20 mm nominal size) |
| 9 | b) 1: 2: 4 ( 1 Cement: 2 fine sand: 4 Graded stone aggregate 20 mm nominal size) |
| 10 | 7) Reinforced cement concrete work in walls(any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars,piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttaring, finishing and reinforcement. 1: 1 ½ :3 ( 1 Cement: 1 ½ fine sand: 3 Graded stone aggregate 20 mm nominal size) |
| 11 | 8) Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement . RCC work in suspended floors, roofs having slope upto15° landings, balconies, shelves and chajjas. 1: 1 ½ :3 ( 1 Cement: 1 ½ fine sand: 3 Graded stone aggregate 20 mm nominal size) |
| 12 | 9) Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe- 500D or more. |
| 13 | 10) Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe- 500D or more. |
| 14 | 11) Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits 50 mm thick |
| 15 | 12) Centering shuttering including struttings, propping etc. and removal of form work for .a) Foundations, footings, bases for columns etc. for mass concrete with 12 mm timber plank. |
| 16 | b)Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply. |
| 17 | c)Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply. |
| 18 | d)Columns, pillars, piers, Abutments, posts and struts with shuttering ply. |
| 19 | e)Edges of slabs and breaks in floors and walls under 20cm wide. |
| 20 | f)Weather shade, Chajjas, corbels etc. including edges. |
| 21 | D)SUB-HEAD : BRICK WORK 13) First class brick work in foundation and plinth including cost of all materials as required complete. a) In cement mortar 1:4(1 cement: 4 fine sand) |
| 22 | . b) In cement mortar 1:6(1 cement: 6 fine sand) |
| 23 | 14) First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete. a) In cement mortar 1:6(1 cement: 6 fine sand) |
| 24 | 15) Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete. In cement mortar 1:4(1 cement: 4 fine sand) |
| 25 | 16) Extra for providing & placing in position 2 nos 6mm dia MS bars at every 6th course of full brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete. In cement mortar 1:4(1 cement: 4 fine sand) |
| 26 | E)SUB-HEAD :WOOD AND PVC WORK 17) Providing wood work in frames of doors, windows,clerestory windows and other frames, wrought framed and fixed in position. Local Teak Wood. |
| 27 | 18) Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 28 | 19) Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all completeFixed to openings /wooden frames with rawl plugs screws etc |
| 29 | 20) Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size). |
| 30 | 21) Providing and fixing IS : 1341 marked M.S. heavy weight butt hinges with necessary screws etc. complete .a)125 x 90 x 4.00 mm |
| 31 | .b) 100 x 75 x 3.50 mm |
| 32 | 22) Providing and fixing ISI marked oxidised M.S. door latches comforming to IS:5930 with screws etc. complete. a)300 x 20 x 6 mm |
| 33 | .b)250 x 20 x 6 mm |
| 34 | 23) Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete a) 250 x 10 mm |
| 35 | b) 200 x 10 mm |
| 36 | 24) Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete .a) 125 mm |
| 37 | .b) 100 mm |
| 38 | 25) Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete Single rubber stopper |
| 39 | 26) Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality) |
| 40 | 27) Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete |
| 41 | 28) Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 42 | 29) Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having mooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter) |
| 43 | 30)Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 44 | F)SUB-HEAD :STEEL WORK 31) Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C slabs during laying including painting the exposed portion of loop, all as per standard design complete |
| 45 | 32) Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-In grating, frames, guard bar, railing, brackets, gates and similar works, all complete |
| 46 | 33) Providing and fixing M.S. round holding down bolts with nuts and wahser plates complete as per standard design |
| 47 | 34) Steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-Hot finishing welded type tubes. |
| 48 | 35) Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required.M.S tube |
| 49 | G)SUB-HEAD :ALUMINIUM WORK & STRUCTURAL GLAZING 36.) Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, run free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws, all complete as per architectural drawing and the direction of Engineer-in-charge.(Glazing and paneling and dash fasteners to be paid for separately) a) For fixed portion of approved quality .Anodised aluminium ( anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 50 | 36 b) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provisionfor fixing fittings wherever required including the cost of EPDM rubber/neoprene gasket required(Fittings shall be paid for separately) .Anodised aluminium ( anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 51 | 37) Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc with EPDM rubber/neoprene gasket etc. complete as per architectural drawing and the direction of the Engineer-in-charge ( Cost of snab beading shall be paid in basic item (a) With float glass panes of 4.0 mm thickness ( Weight not less than 10.0 kg/ Sqm |
| 52 | 38) Providing and fixingstainless steel ( SS 304 grade ) adjusable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of the Engineer-in-charge .a)205x19mm |
| 53 | H)SUB-HEAD :FLOORING AND SKIRTING WORK 39) Providing and laying ceramic floor tiles in different sizes ( thickness to be specified by the manufacturer ) of 1st quality conforming to IS : 15622-2017 of approved make in colours such as white, Ivory, grey, Fume, Red Brown, laid over 20mm thick cement mortar 1: 4 ( 1 Cement: 4 fine sand ) jointing with grey cement slury @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete (A).Mat Finish Tiles Ceremic glazed tiles 1st quality 400x400 mm in all shade and design |
| 54 | (B).anti skid tiles Ceremic glazed tiles 1st quality 400x400 mm in all shade and design |
| 55 | 40) Providing and fixing 1st quality ceramic glazed wall tiles ( minimum 200x300) conforming to IS : 15622-2017 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades of any size as approved by the Engineer-in-charge in skirting ,riser of steps and dados, laid over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 fine sand ) joined with ordinary cement slury including pointing with white cement mixed with pigment of matching shade complete |
| 56 | 41) Providing and fixing precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning complete as per direction of the Engineer-in-charge. |
| 57 | 42) Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded stone aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. complete 40 mm thick with 20 mm stone aggregate |
| 58 | I)SUB-HEAD :ROOFING AND CEILING WORK 43) Supply & installation of pre painted galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in charge) in 550 mpa steel grade, made out of Cold Rolled Steel coated with Zinc- Aluminium alloy coating of 43.5% Zn, 55% AI and 1.5% Silicon comfirming to ASTM A792/A792M and S1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of siez (5.5 x 55 mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlings, rafters and trusses and including cutting to size and shape wherever required.I) 0.50 MM |
| 59 | 44) Supply & installation of pre-painted Galvalume sheets roofing accessories in 55 mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% AI and 1.5% silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester pf 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling/self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/ Flashing of width 610 mm.i) 0.50 mm thickness |
| 60 | 45) Providing and fixing PVC false ceiling with SPUF 142-D-01(different design 10 mm thick 150 mm width and necessary length) of approved colour concealed type panel carrier T-section (DWUF: 406:40 x 63:50 mm and L-section (DWUF: 405:40 x 48 mm) with necessary screws, hold fast, wooden beading and MS black pipe structure 48 mm dia, at 1200 mm centre to centre including cutting holes and making good the walls etc. complete as per direction of the Engineer-in-charge. |
| 61 | J)SUB-HEAD :FINISHING WORK 46 ) 12 mm cement plaster of mix A) In cement mortar 1:4(1 cement : 4 fine sand) |
| 62 | b) In cement mortar 1:6(1 cement : 6 fine sand) |
| 63 | 47) 15 mm cement plaster on the rough side of single or half brick wall of mix. In cement mortar 1:6 (1 cemnt : 6 fine sand) |
| 64 | 48) 6 mm cement plaster of mix.In cement mortar 1:3 (1 cemnt : 3 fine sand) |
| 65 | 49)Neat cement punning |
| 66 | 50) Distempering with oil bound washable distemper of approved brand and manufacture to give an even hade (payment shall be made after submission of Test Certificate issued by the Manufacturer): new work ( two or more coats ), over and including water thinnable priming coat of cement primer. |
| 67 | 51) Finishing walls with water proofing cement paint of required shade of approved brand and manufacture(payment shall be made after submission of Test Certificate issued by the Manufacturer) new work ( two or more coats applied @ 3.84 kg/10 sqm). |
| 68 | 52) Applying priming coat (payment shall be made after submission of Test Certificate issued by the Manufacturer) a)With ready mixed pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 69 | b)With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel, galvanised iron / steel work. |
| 70 | 53) Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (payment shall be made after submission of Test Certificate issued by the Manufacturer) Two or mora coats on new work. |
| 71 | K)SUB-HEAD SANITARY WORKS 54) Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 72 | 55) Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid |
| 73 | 56) Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively |
| 74 | 57)Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings. Flat back wash basin of size 630x450mm. |
| 75 | 58.) Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete A)Semi rigid pipe 32 mm dia |
| 76 | B) Flexible pipe 32 mm dia |
| 77 | 59) Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Circular shape 450 mm dia. |
| 78 | 60) Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 79 | 61) Providing and fixing toilet paper holder CP brass |
| 80 | 62) Providing and fixing PMPT towel rail complete with brackets fixed to wooden cleats with CP brass screws with consealed fitting arrangements of approved quality and colour 600 mm long towel rail with total length 645 mm , with 78 mm and effective height of 88mm, weighting not less than 106 gms. |
| 81 | 63) Providing and fixing PMPT soap Dish holder having length of 138 mm, breadth 102 mm, height of 75 mm with consealed fitting arrangements weighting not less than 106 gms . |
| 82 | 64) Providing and fixing on wall face unplasticised Rigid PVC rain water soil, waste & vent pipes ( Working pressure 6 kg/cm2 ) conforming to IS 13592 Type A includng jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion Single socketed pipe 100 OD |
| 83 | 65)Providing and fixing unplasticised- PVC pipe clips of approved design to unplasticised - PVC rain water soil, waste & vent pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S screws of required length including cutting brick work and fixing with cement mortar 1:4 ( 1 cement : 4 fine sand ) making good to the wall etc a) 110 mm |
| 84 | 66 a) Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water , soil, waste & vent pipes conforming to IS : 13592 type A including jointing with seal ring conforning to IS :5382 leaving 10 mm gap for thermal expansion i) Coupler a) 110 mm |
| 85 | 66 b) Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water , soil, waste & vent pipes conforming to IS : 13592 type A including jointing with seal ring conforning to IS :5382 leaving 10 mm gap for thermal expansion ii) Single equal tee without door 110x110x110 mm |
| 86 | 66 c) Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water , soil, waste & vent pipes conforming to IS : 13592 type A including jointing with seal ring conforning to IS :5382 leaving 10 mm gap for thermal expansion iii) Single equal tee with door 110x110x110 mm |
| 87 | 66 d) Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water , soil, waste & vent pipes conforming to IS : 13592 type A including jointing with seal ring conforning to IS :5382 leaving 10 mm gap for thermal expansion v) Plain shoe 110 mm |
| 88 | 66 e) Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water , soil, waste & vent pipes conforming to IS : 13592 type A including jointing with seal ring conforning to IS :5382 leaving 10 mm gap for thermal expansion iv) Bend 87.5 " 110 mm |
| 89 | 66. f) Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water , soil, waste & vent pipes conforming to IS : 13592 type A including jointing with seal ring conforning to IS :5382 leaving 10 mm gap for thermal expansion vi) Terminal guard 110 mm |
| 90 | L)SUB-HEAD : WATER SUPPLY 67 a) Providing and fixing G I pipes of medium class as per IS :1239 with latest amendment complete with G.I fittings and clams, including cutting and making good to the walls etc. complete as per CPWD specification and direction of the Engineer-in-charge. Internal work- Exposed on wall a) 15 mm dia nominal bore |
| 91 | 67 b)Providing and fixing G I pipes of medium class as per IS :1239 with latest amendment complete with G.I fittings and clams, including cutting and making good to the walls etc. complete as per CPWD specification and direction of the Engineer-in-charge. Internal work- Exposed on wall b) 20 mm dia nominal bore |
| 92 | 67 c) Providing and fixing G I pipes of medium class as per IS :1239 with latest amendment complete with G.I fittings and clams, including cutting and making good to the walls etc. complete as per CPWD specification and direction of the Engineer-in-charge. Internal work- Exposed on wall c) 25 mm dia nominal bore |
| 93 | 68 ) Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete a) 25 to 40 mm nominal bore mm dia nominal bore |
| 94 | 69) Providing and fixing brass bib cock of approved quality 15 mm nominal bore |
| 95 | 70)Providing and fixing brass stop cock of approved quality 15 mm dia nominal bore |
| 96 | 71 )Providing and fixing gun metal gate valve with C.I wheelof approved quality ( Screwed end ) 25 mmnominal bore |
| 97 | 72 )Providing and fixing gun metal non-return valve of approved quality ( Screwed end ) 25 mmnominal bore vertical |
| 98 | 73 ) Providing and placing on terrace ( at all levels ) polythene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support of tank . |
| 99 | 74 a) Painting G.I pipes and fittings with synthetic enamel white paint over a ready mixed primimg coat, both of approved quality for new work . a) 15 mm diameter pipe . |
| 100 | 74 b) Painting G.I pipes and fittings with synthetic enamel white paint over a ready mixed primimg coat, both of approved quality for new work . b) 20 mm diameter pipe . |
| 101 | 74 c) Painting G.I pipes and fittings with synthetic enamel white paint over a ready mixed primimg coat, both of approved quality for new work . c) 25 mm diameter pipe . |
| 102 | 75 a) Painting G.I pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality . a) 15 mm diameter pipe . |
| 103 | 75 b) Painting G.I pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality . b) 20 mm diameter pipe . |
| 104 | 75 c) Painting G.I pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality . c) 25 mm diameter pipe . |
| 105 | M)SUB-HEAD : SEWAGE AND DRAINAGE 76 ) Providing and laying glazed stoneware pipes grade "A" with stiff mixture of cement mortar in the of 1:1 ( 1 cement : 1 fine sand ) including testing of joints etc. complete . a) 150 mm diameter . |
| 106 | 77 ) Providing and laying cement concrete 1:5:10 (1 cement :5 fine sand 10 stone aggregate 40mm nominal size ) alround S.W pipes including bed concrete as per standard design . a) 150 mm diameter S.W pipe |
| 107 | 78 ) Constructing soak pit 1.20x1.20 x1.20 m filled with brick bats including S.W drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 108 | N)SUB-HEAD : INTERNAL ELECTRIFICATION 79 a) Wiring for light /fan/ exhaust fan/call bell point with 2x 1.5 sq.mm PVC insulated copper conductor cable with(FR) in pvc casing and capping complete with wooden switch board with bakelite cover and piano type awitch including connection etc. as required. Short point |
| 109 | 79 b) Wiring for light /fan/ exhaust fan/call bell point with 2x 1.5 sq.mm PVC insulated copper conductor cable with(FR) in pvc casing and capping complete with wooden switch board with bakelite cover and piano type awitch including connection etc. as required. Mediam point |
| 110 | 79 c) Wiring for light /fan/ exhaust fan/call bell point with 2x 1.5 sq.mm PVC insulated copper conductor cable with(FR) in pvc casing and capping complete with wooden switch board with bakelite cover and piano type awitch including connection etc. as required. Long point |
| 111 | 80) Providing and fixing of 3 pin 5/6 pin amps plug point with piano type 15/16 amps switch and socket including connection with 2x1.5 sq.mm PVC insulated copper conductor cable(FR) on switch board, earting the 3rd pin etc. as required. |
| 112 | 81 ) Providing and fixing of 3/6pin 15/16 pin amps plug point with piano type 15/16 amps switch and socket including connection with 2x2.5 sq.mm PVC insulated copper conductor cable(FR) on switch board, earting the 3rd pin etc. as required. |
| 113 | 82 a) Wiring for circuit/Sub-main wiring with following sizes PVC insulated copper conductor cable(FR) in PVC casing capping etc. as required. 2 x 1.5 sq. mm |
| 114 | 82 b) Wiring for circuit/Sub-main wiring with following sizes PVC insulated copper conductor cable(FR) in PVC casing capping etc. as required. 2 x 2.5 sq. mm |
| 115 | 82 c) Wiring for circuit/Sub-main wiring with following sizes PVC insulated copper conductor cable(FR) in PVC casing capping etc. as required. 2 x 4 sq. mm |
| 116 | 82 d)Wiring for circuit/Sub-main wiring with following sizes PVC insulated copper conductor cable(FR) in PVC casing capping etc. as required. 2 x 6 sq. Mm |
| 117 | 83 a) Wiring for circuit/Sub-main with the following sizes PVC insulated copper conductor cable(FR) in existing PVC casing capping/conduit in recess/ surface including connection etc. as required. 1 x1.5 sq.mm |
| 118 | 83 b) Wiring for circuit/Sub-main with the following sizes PVC insulated copper conductor cable(FR) in existing PVC casing capping/conduit in recess/ surface including connection etc. as required. 1 x 2.5 sq.mm |
| 119 | 83 c) Wiring for circuit/Sub-main with the following sizes PVC insulated copper conductor cable(FR) in existing PVC casing capping/conduit in recess/ surface including connection etc. as required. 1 x 4 sq.mm |
| 120 | 83 d) Wiring for circuit/Sub-main with the following sizes PVC insulated copper conductor cable(FR) in existing PVC casing capping/conduit in recess/ surface including connection etc. as required. 2 x2.5 sq.mm |
| 121 | 83 e) Wiring for circuit/Sub-main with the following sizes PVC insulated copper conductor cable(FR) in existing PVC casing capping/conduit in recess/ surface including connection etc. as required. 2 x 4 sq.mm |
| 122 | 83 f) Wiring for circuit/Sub-main with the following sizes PVC insulated copper conductor cable(FR) in existing PVC casing capping/conduit in recess/ surface including connection etc. as required. 2 x 6 sq.mm |
| 123 | 84) Earthing with 40 mm dia G.I Earth pipe(medium gauge) 4.5 m long complete with masonry enclosure on top CI cover plate size 12" x 12" having locking arrangment including CC work, holes on earth pipe etc. as required. |
| 124 | 85) Extra for using salt (5 kg) and charcoal (46 kg) for pipe earth electrodeas required. |
| 125 | 86) Providing and laying 15mm dia(medium gauge) G.I pipe for drawing of 4.6 mm(8SWG) dia G.I/Copper wire for earth connection from earth electrodes etc. as required. |
| 126 | 87) Providing and fixing/Drawing 4.06 mm dia (8SWG) copper wire on surface or in existing G.I/PVC/Polythine pipe for loop earthing as required. |
| 127 | 88) Supplying and installation of switch disconnector fuse unit (main switch) of the following ratings with all accessories including necessary connection etc. as required. 32 amps 240 volts DP main switch(rewireable) |
| 128 | 89) Supplying and installation of powder coated sheet steel enclosure(MCB) suitable for 240/415 volts MCB/Isolator /RCCB(SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required. (2+10)/12 way SPN MCB DB(single door) |
| 129 | 90 a) Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing Panels/MCB DBs including necessary connections etc as required. 6 to 32 amps SP MCB |
| 130 | 90 b) Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing Panels/MCB DBs including necessary connections etc as required. 6 to 32 amps DP MCB |
| 131 | 91 a) Supplying and fixing of the following electrical accessories including necessary connection etc as required. 5/6 amps piano type call bell push |
| 132 | 91 b) Supplying and fixing of the following electrical accessories including necessary connection etc as required. Electronic 4 step mini fan regulator |
| 133 | 91 c) Supplying and fixing of the following electrical accessories including necessary connection etc as required. Buzzer call bell |
| 134 | 91 d) Supplying and fixing of the following electrical accessories including necessary connection etc as required. 32 amps DP kit kat switch |
| 135 | 92 ) Supplying and fixing of the following sizes PVC conduit (medium gauge) on surface with all accessories etc as required. 19/20 mm dia |
| 136 | 93 ) Supplying and fixing of following luminaries complete with necessary accessories and connection etc. as required(Commercial lighting fixure with 50000 burning hours) Box type single FTL fittings of CRCA steel sheet housing complete with 36/40 W FTL, electronic ballast and high quality reflector cover. |
| 137 | 94 ) Supplying and fixing of following outdoor LED luminaries in powder coated dis cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt) 6 watt/10 watt LED Bulkhead light with high quality polycarbonate diffuser(IP 65) |
| 138 | 95) Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required. 5 watt LED retrofit lamp with polycarbonate body and aluminium heatsink. |
| 139 | 96) Supplying and fixing of copper terminal ends(LUGS) long barrel of following sizes. 6 sq. mm |
| 140 | 97) Supplying and fixing of MS frame made of (25 mm x 25 mm x 5 mm) MS angle with necessary support by (40 mm x 6 mm) MS flat and 12 mm thick marine plywood on top, grouted on wall with 4 nos legs (25 mm x 25 mm x 5 mm MS angle 20 cm long) finished with red oxide and 2 coat aynthetic enamel paint including necessary cc work, mending the damages & painting etc. as required. |
| 141 | 98) Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc. as required. |
| 142 | 99) Supplying and installation of shutter for 225/230/300 mm sweep metalic body exhaust fan in the existing hole as required. |
| 143 | 100) Making different sizes of hole in the wall for fixing of exhaust fan including finishing the same with cement plastering and painting etc. as required. |
| 144 | 101) Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc. as required. 2 core 4 sq mm |
| 145 | 102) Drawing of armoured/uu-armoured cable with proper saddling etc. as required. |
| 146 | 103) Supplying & fixing of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod, canopies, shackles, 3 nos blades, including wiring the down rod with 2 x 1.5 sqmm PVC insulated copper conductor cable(FR)(ISI) marked, BEE 1 star/minimum service value 4.0 m3/min/W). |
| 147 | 104) Supplying and fixing of the following sizesWooden switch boards with 3mm thick bake lite cover etc. as required . 152 mmx 203mm ( 6" x 8" ) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
