|
| 1 | Surface dressing of the ground by way of removing of bushes , grasses ,and disposal of the same complete job |
| 2 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2on plan) including disposal of excavated earth lead upto 50 Engineer-in-Charge. All kinds of soil : including dewatering of trenchescomplete job |
| 3 | Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive. |
| 4 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in- charge: |
| 5 | 1:3:6 or richer mix (i/c equivalent design mix) |
| 6 | Demolishingbrickworkmanually bymechanicalmeansincluding stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar |
| 7 | P/L of dry stone soling (Nallah/quarry broken stones), Hand Packed i/c carriage of material from source to site of work and including dewatering charges during exeuction of work complete job |
| 8 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with and including dewatering charges during exeuction of workand including dewatering charges during exeuction of work complete job |
| 9 | (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 10 | (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 11 | (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Cold twisted barsand including dewatering charges during exeuction of work |
| 14 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement lime mortar 1:1:6 ( 1 cement : 1 lime putty : 6 fine sand) |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form work for and including dewatering charges during exeuction of work complete job |
| 16 | Foundations, footings, bases for columns |
| 17 | Retaining walls, return walls, walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs and steps etc. |
| 18 | Suspended floors, roofs, landings, balconies and access platforms. |
| 19 | Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 20 | 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand) |
| 21 | 20mm Cement plaster of mix: ( 1 cement : 6 fine sand) |
| 22 | KOTA STONE FLOORING Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed withpigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) : |
| 23 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 24 | Providing & laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen & the like consisting of:(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. Per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). |
| 25 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 26 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Zsections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size includingnecessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) 10mm guage |
| 27 | for shutters of doors /window at ventilators incluidng cost of snap beeding , EPDM rubber /neoprene gasket requiredcomplete job |
| 28 | P/F of 4mm thick Alminium partation pannel ( APP) alstone or equilvent including cost of rubber beeding , gaskit etc complete job |
| 29 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer- in-charge. including cost of snap beeding /rubbergasket (5mm thick complete job) |
| 30 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm Somany /Kajaria or equilvent |
| 31 | Providing and applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete |
| 32 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete.2 mm thick |
| 33 | P/F of 3mm thick Aluminium composite pannel (ACP) Alstone or equilvent including cost of silicon, frmae work of Alminium tubesand cost of scaffolding charges complete job |
| 34 | P/F of T&G imported wooden ceiling / sofits (budloo) includng cost of Budloo wood and joistsincluding applying of primer/painting and scaffolding charges complete job |
| 35 | Providing and fixing plained eaves boarding. 2nd class Deodar wood 300x40 mm (nominal size) |
| 36 | 2nd class kail wood |
| 37 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Including priming coat and scaffolding charges complete job |
| 38 | P/F of colour coated panelling type CGI sheets including cost of necessary frame work of budloo wood joists and including cost of scaffolding charges complete job |
| 39 | P/F of thermo insulation for GI water supply pipes out of flaxable elastemater having thermal conductivity of 0.038% of 200% water vapour permability including cost of adhesive /tape at joints complete job |
| 40 | 32mm diaG.I pipes |
| 41 | 50mm dia G.I Pipes |
| 42 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) including scaffolding charges |
| 43 | WallPaintingwithacrylicemulsionpaintofapprovedbrandand manufacture to give an even shade. Two or more coats on new work including priming coat & scaffolding charges complete job |
| 44 | Supply and filling of Nallah muckh including laying spreading levelling watering and consoldation with (100-80) KN road roller including loading unloading and carriage upto site of work and including. |
| 45 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. |
| 46 | 100mm dia. |
| 47 | 75mm dia. |
| 48 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls and including excavation of trenches and refilling complete job |
| 49 | 15 mm dia. nominal boreMedium(B) |
| 50 | 32 mm dia. nominal boreMedium(B) |
| 51 | 50 mm dia. nominal boreMedium(B) |
| 52 | P/F and installation of PVC water storage tank triple layer of approved quality including cost of necessary G.I fittings like taky nipples , ball valve , ball cock , over flow controll value and making of necessary plate form complete job |
| 53 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :1.5:3 mix ( 1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :- Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight ofcover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : |
| 54 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 10.6.180x1.25 mm M.S. laths with 1.25 mm thick top cover complete job |
| 55 | P/F of flush valve approved make or equilvent including cost of all materials complete job |
| 56 | P/F of C.P bibcock 15mm dia including cost of nuts , washers , cups , niples complete job or equilvent |
| 57 | P/F of 100mm dia c P grating complete job |
| 58 | P/F of CP brass wall mixer/basin mixer /sink mixerwith all accessiors required or equilvent complete job |
| 59 | P/F of brass angle value jaquar or equilvent including cost of all required accessiors complete job |
| 60 | P/F of C.P soap dish including cost of PVC plugs , nuts screws etc complete job |
| 61 | P/F of ball valve of brass approved make including necessary accessiors complet job |
| 62 | 50 mm dia. |
| 63 | 32 mm dia. |
| 64 | P/F of fency type mirror (18\" x 24\") size including PVC plugs and screws complete job |
| 65 | P/F of water storagehot water ( Gyser approved make) with copper connection insulation thermostatically controlled immerse heater suitable length of electric cable with 15mm PVC connection , |
| 66 | 50 Ltr capacity |
| 67 | 35 Ltr capacity |
| 68 | P/F of vitreous china ware wash basin ( flate back pattern 550 x 400 mm size) in standard colour as specified including cost of MS brackets cutting of holes making good the same surface including cost of pedestal and CP wastecomplete job Hindware or equilvent |
| 69 | P/Fabrication of structural steel truss work in built up sections , trusses and framed work including cutting hoisting welding and fixing in position and applying a coat of approved steel primer complete job |
| 70 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 71 | Providingandfixingprecoatedgalvanisedsteelsheetroofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm) |
| 72 | P/F and embedding in cement concrete 16mm dia truss bolts including cost of nuts washers complete job |
| 73 | Providing and laying of M.S pipes including welding charges, costof nuts and bolts and all fittings like bends , elbow , puddle flange and refilling of trenches complete job medium size (prakash suriya , jindal or equilvent ) including cutting and making of holes of RCC walls and including making the surface good |
| 74 | 80mm dia |
| 75 | 100mm dia |
| 76 | 150 mm dia |
| 77 | Note: The Departmental material if any available at site be utilized and same shall be deducted as per the prevailing rate |
