Public Works Department-PWD has published Remodelling Of Govt. Higher Secondary School Boys ( Three Storey ) Including Sanitary Fitting, Water Supply, Drainage System, Pumps Equipments At Boys Higher Secondary School Kishtwar Please Refer Boq. Submission Date for this Tender is 17-12-2021. Building Work Tenders in KISHTWAR Jammu And Kashmir. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge in all kind of soil |
| 2 | Extra for every additional lift of 1.5 M or part therefore in all kinds of soil. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed. |
| 4 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including Admixtures in recommended proportions, (as per IS 9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-chargeAll work upto plinth level. |
| 5 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including Admixtures in recommended proportions, (as per IS 9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-chargeAll work above plinth level upto floor V level. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 7 | Providing and laying DPC 50mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) and curing complete. |
| 8 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) |
| 9 | Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 10 | Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:6 (1 cement : 6 fine sand). |
| 11 | Extra for brick work in super structure above plinth level upto floor V-level. |
| 12 | Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand). |
| 13 | Extra for half brick work in super structure above plinth level upto floor V-level. |
| 14 | Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars. |
| 15 | 12mm thick cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement : 3 fine sand). |
| 16 | 12mm cement plaster of mix 1:6 (1 cement : 6 fine sand). |
| 17 | 15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand). |
| 18 | Making of grove 12mm x 10mm between brick and RCC. |
| 19 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size below flooring, retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing. |
| 20 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50Mt & lift upto 1.50M. |
| 21 | Supply selected/ approved earth brought from outside the site and filling the same in plinths, back of retaining walls, foundations and trenches and spreading in landscaping and other location as directed by the Project Manager and shall be done in layers, not exceeding 20cm in depth and consolidating each deposited layer by mechanical means, ramming and wateringas per specifications including transportation, cost of soil, royalty, loading, unloading, carriage to dumping spot and all incidentals at all depths and levels, for all leads and lifts complete (Net consolidated area fill volume will be computed from the initial and final levels. Volume in slopes, embankments etc. will be computed applying appropriate formula). (Surface vibrator to achieve at least 95%maximum dry density (proctor density) |
| 22 | Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete. |
| 23 | Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections. |
| 24 | Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed. |
| 25 | Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75mm including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form work for :- |
| 27 | Foundations, footings, bases of columns. |
| 28 | Columns, pillars, piers. |
| 29 | Lintels, beams, plinth beams. |
| 30 | Suspended floors, roofs, landings and access platforms. |
| 31 | Edges of slabs and breaks in floors and walls upto 20cm wide. |
| 32 | Stairs (excluding landings) except spiral stair cases. |
| 33 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 34 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 mtr. of part thereof (Plan area to be measured). Suspended floors, roofs landing, beams and balconies (Plan area to be measured). |
| 35 | Providing and laying water proofing treatment (Make Armocreate of SWC Chryso France) to vertical and horizontal surface of depressed portions of W.C., kitchen and the consisting of (i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface. (ii) IInd course of20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surface. (iii) III course of applying blown or / residual bitumen applied hot at 1.7 kg per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm. |
| 36 | Kota stone slab flooring over 20mm (avg.) thick base laid over and jointedwith grey cement slurry mixed with pigment to match the shade of the slab includingrubbingandpolishing completewithbaseofcementmortar1:4 (1 cement : 4 coarse sand) 25mm thick. |
| 37 | Kota stone slab 25mm thick in riser of steps, skirting, dado and pillars laid on 12mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 38 | Providing and fixing ceramic glazed floor tiles (non-skidding) 300x300mm (thickness to be specified by the manufactures) of Ist quality conforming to IS : 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, Ivory, Grey, Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete. |
| 39 | Providing and laying polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 40 | Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. |
| 41 | Providing and fixing PRM Quality Ceramic Glazed wall tiles of Size 300x600 mm conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 42 | Providing and laying 18mm thick Granite of any colour and shade (area of slab over 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for Floors and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. |
| 43 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) sal wood |
| 44 | Providing & fixing glazed shutters 35mm thick for doors, windows and clear story windows using 10Kg/Sqm (4mm thick) glass panes including stainless steel but hinges of size 75mm x 62mm x 2mm of make Kitch, Arch, Blum with necessary stainless screws in second class deodar wood. |
| 45 | Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauge of average width for aperture 1.4mm in both direction with wire of dia 0.63mm for doors, windows and clerestory windows with hinges and necessary screws in second class deodar wood. |
| 46 | Providing and fixing of glass panes weighing 12.50 kg/sqm (5.0mm thick) with deodar wood fillets. |
| 47 | Providing and fixing ISI marked 35mm flush door shutters conforming ti IS: 2202 (Part 1) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both face of shutters including ISI marked M.S pressed bright finished butt hinges with necessary screws of required size |
| 48 | Providing and fixing aluminium tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparentor dyed to required colour or shade with necessary screws etc. complete. |
| 49 | 150x10mm. |
| 50 | 200x10mm. |
| 51 | Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparentor dyed to required colour or shade with necessary screws etc. complete. |
| 52 | 125mm. |
| 53 | 100mm. |
| 54 | Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter. |
| 55 | Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion |
| 56 | Coupler 110mm. |
| 57 | Single tee with door 110 x 110 x 110mm. |
| 58 | Bend 87.5* 110mm. |
| 59 | Providing and fixing aluminium sliding door bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparentor dyed to required colour or shade with necessary screws etc. complete. 300x16mm. |
| 60 | Providing and fixing oxidized M.S. hasp and staple (Safety type) conforming to IS : 363 with necessary screws etc. complete. |
| 61 | Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 62 | Providing and fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparentor dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper. |
| 63 | Painting with synthetic enamel paint of approved brand and manufacture to give and even shade two or more coats on new work (Wood work). |
| 64 | Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade (two or more coats) on new steel work. |
| 65 | Providing and fixing M.S. tube hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 66 | Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.). |
| 67 | Steel work welded in built-up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, railings, brackets, gates and similar work. |
| 68 | Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacture,over the plasterted wall surface to prepare the surface even and smooth complete |
| 69 | White washing with lime to give an even shade. New work (three or more coats) |
| 70 | Finishing wall with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm) |
| 71 | Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work. |
| 72 | Providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087, finished with a coat of aluminum primer on both sides & edges, including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodized aluminum (with 15 micron anodic coating) Tsections 35 x15x1.5 mm size main runners, cross runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600 x 1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of zinc chromate yellow primer (aluminum frame work shall be paid separately). |
| 73 | Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. |
| 74 | Structural steel work welded in built-up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Riveted and bolted. |
| 75 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal / vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63mm thick with zinc coating not less than 275gm/sqm. |
| 76 | Providing ridges or hips of width 60cm overall width plain G.S. Sheets fixed with polymer coated J or L hooks, bolts and nuts 8mm dia G.I limpet and bitumen washers complete. 0.63mm thick with zinc coating not less than 275gm/kg |
| 77 | Providing and fixing wind ties of 40x6mm flat iron section. |
| 78 | Dismantling:- Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of G.S. Sheet. |
| 79 | Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead of sectional area 40 sqcm. and above. |
| 80 | Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge in cement mortar |
| 81 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge in cement mortar |
| 82 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead of area of 3 sqm. and below |
| 83 | Carriage for demolish/dismanteled items upto a lead of 5km. |
| 84 | Vide Item No.63 @ 40% of 298.44 |
| 85 | Vide Item No.64 @ 40% of 5.64 |
| 86 | Plumbing:- SUB HEAD - I : SANITARY FIXTURES :- Providing and fixing water closet squatting pan (Indian Type W.C Pan) with 100mm sand cost iron P or S trap, 10 ltrs low lewel PVC flushing cistern including flush pipe (Hindware make Cat No. 20070/ Kerovit make Cat No. 606) Manually controlled device (Handle lever) conforming to IS : 7231, with all fitting and fixture complete including cutting and making good the wall and floows wherever required. Orissa Pan white viterous china pan of size 580x440mm with integral type footrests. |
| 87 | Providing & fixing of white vitreous China pedestial type water closet (European Type) with cistern (A/PHAS-100 Cat No. 201100+Cat No. 21054 / Kerovit model No. 112 and flush tank model no. 1001) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge. |
| 88 | Providing & fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008 + Ped Cat No. 11003 / Kerovit model No. 234 Ped Model no. 305)with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge. |
| 89 | Providing and fixing of C.P. brassCentral Hole Basin Mixer without Popup Waste System including with 450mm Long Copper Pipes & Brass Nuts with all fittings and accessories as per direction of Engineer-Incharge. (Jaquar CQT 23167 D / Kerovit make Cat No. 1511010-ND-CP). |
| 90 | Providing & fixing C.P. hand spray with lever control (health faucet) (Jaquar Cat. No. ALDCHR-565 / Kerovit make KA580001)and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge. |
| 91 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore (Make Jaquar CQT 23059 / Kerovit make Cat No. KB 1511003). |
| 92 | P/F of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat No. ACN 113 N Kerovit Cat No KA 680004). |
| 93 | Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat. no. 70002) comprising of EWC - P , Cistern, Seat Cover, Twin Flush Fittings, Wash Basin 450x300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge. |
| 94 | Providing and fixing 6mm copper backed float glass mirror MODI / SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative, etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer in charge. |
| 95 | P/F of glass shelf 600mm long with all C.P fittings of approved quality complete item (Jaquar Cat No., CAN 11071 N Kerovit Cat No KA 930005). |
| 96 | Providing and fixing 15 mm dia. C.P. brassbib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (Short Body) (Make Jaquar Cat No. CQT-23047 Kerovit Cat No. KB 2011004) |
| 97 | Sub Head- II-Water Supply: Internal work:- Exposed on wall Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer"s name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Clamps at one meter spacing, with PAP valves and brass tank Nipples etc. Including testing of lines and joints as per Engineer in charge.Make Kitec, Maithilee and Vista. |
| 98 | KiTEC Composite 3240 PL as per IAPMO IGC- INDIA 308 (40mm OD) |
| 99 | KiTEC Composite 2025 PEX (Hot water supply) as per IAPMO IGC- INDIA 309 (25mm OD) |
| 100 | Conceal Inside the walls:- Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer"s name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Clamps at one meter spacing, with PAP valves etc. Make Kitec, Maithilee and Vista.Concealed, installation including cutting chases and making good in the wall etc, Complete in all respect. 1620(20mm OD) pipe. |
| 101 | KiTEC Composite 1620 PL as per IAPMO IGC- INDIA 308 (20mm OD) |
| 102 | KiTEC Composite 1620 PEX (Hot water supply) as per IAPMO IGC- INDIA 309 (20mm OD) |
| 103 | KiTEC Composite 2025 PL as per IAPMO IGC- INDIA 308 (25mm OD) |
| 104 | Internal work:- Exposed on wall Providing and fixing of Polyethylene/Aluminum/Polyethylene (PE-AL-PE) composite Pipes as per IAPMO IGC-INDIA 308, UMC-1 TM certification marked on the pipe at the interval not greater than 1 meter with nominal pipe size with manufacturer"s name or trade mark including all relevant DZR brass fittings as Female Elbows/Tees, MTC/FTC and Engineering plastic fittings with internal sealing system like Eq. elbows, Eq. tees, reducers, Straight couplers, Connectors, with PAP valvesetc. Trenching, re filling and testing etc. Complete as per Engineer In Charge. Make Kitec, Maithilee and Vista. |
| 105 | KiTEC Composite 1620 PL as per IAPMO IGC- INDIA 308 (20mm OD) |
| 106 | KiTEC Composite 2025 PL as per IAPMO IGC- INDIA 308 (25mm OD) |
| 107 | KiTEC Composite 2532 PL as per IAPMO IGC- INDIA 308 (32mm OD) |
| 108 | KiTEC Composite 3240 PL as per IAPMO IGC- INDIA 308 (40mm OD) |
| 109 | Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) (Medium Class) |
| 110 | 32 mm dia. nominal bore |
| 111 | BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified |
| 112 | 32mm dia. |
| 113 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete |
| 114 | 25 to 40 mm nominal bore |
| 115 | Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm. |
| 116 | 15 mm dia |
| 117 | 20 mm dia |
| 118 | Providing and fixing in position of approved quality high pressure rated Brass Float Valve with copper ball float and brass rods of required length suitable fortest pressure of not less than 15 Kg/sqcm of the following sizes: |
| 119 | 32 mm dia |
| 120 | SUB HEAD - III : DRAINAGE SYSTEM:- Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed. |
| 121 | Supply and Fixing SILENCIO (High density low noise system) sound insulated polyproplene piping system as per ON EN 1451-Part 1 & EN 12056 Part 1-5, DIN 1986-100, with 3 layer pipe made of PP/PP-MV/PP, push fit type, food safe, having high impact and stiffness, offering sound levels not more than 16dBA as per DIN 4109, sewerage piping system suitable for drainage of commertial and residential waste water for both hot and cold water with Engineering plastic fittings like bends, tees, reducers, couplers, connectors, etc as per DIN EN 12056 and DIN 1986-100. (Astral Silencio Make). In the bathroom, down take/rain water & underground |
| 122 | 75MM Socketed pipe (3 meter long) 1.7MM |
| 123 | 110MM Socketed pipe (3 meter long) 1.7MM |
| 124 | 160MM Socketed pipe (3 meter long) 1.7MM |
| 125 | Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate) |
| 126 | Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. (With F.P.S. bricks) |
| 127 | Providing murum bedding below pipeline and filling on the top of the pipeline with selected material in 15 to 20 cm layers including watering ramming etc. complete. With selected earth available from excavation. |
| 128 | Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked) |
| 129 | Providing and fixing heavy class SS grating plane including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge (Size 100 mm dia) (ISI Marked) |
| 130 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) |
| 131 | Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks. |
| 132 | SUB HEAD - WATER SUPPLY, DRAINAGE, PUMPS & EQUIPMENT:- Supply, assembly, erection, testing and commissioning of pumping system comprising the following:- Vertical/Horizontal centrifugal pumps (1 Working + 1 Stand-by) with mechanical seal, SS Volute casing and SS impeller connected to suitable capacity TEFC induction motor suitable for 415 ± 10 % volts, 3 phase, 50 cycles A.C. supply with 100 mm dia. pressure gaugesincluding MS skid and mounting of the pumps on the skid. (Motor to be of the same make as the pump) |
| 133 | Pump Capacity 180 lpm, at 30 m head (1 working + 1 standby) (Domestic water relift pump). |
| 134 | Carriage of material by Mechanical Transport including loading / unloading and stacking at site complete. |
| 135 | Sand for an average lead of 13 Kms. |
| 136 | Stone aggregate below 40mm size for an average lead of 5 Kms. |
| 137 | Stone aggregate 40mm and above 40mm size for an average lead of 5 Kms. |
| 138 | Bricks for an average lead of 220 Kms |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
