|
| 1 | Civil Work itemsDemolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. HSR 5.7 5.7.4 In cement mortar |
| 2 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. HSR 5.235.23.2 Nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix) |
| 3 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : HSR 5.29 5.29.1 Of area 3 sq. metres and below |
| 4 | 5.29.2 Of area beyond 3 sq. Metres |
| 5 | Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:HSR 5.325.32.2Channels, angles, tees and flats |
| 6 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. HSR 5.44 |
| 7 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. HSR 5.45 |
| 8 | Removing old broken/serviceable glass of any thickness or size or description except polished plate glass from old wood or metal frames etc.(any thickness or size) hacking out old putty etc. including making good breakages in talking out and handling complete HSR 5.51 |
| 9 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. HSR 5.70 |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: HSR 6.16.1.61:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 11 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :HSR 9.469.46.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 12 | Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calcium silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. HSR 9.48 |
| 13 | Providing and laying of screed of 40 mm thick cement concrete 1:4:8 to be laid below the topping. HSR 10.6 |
| 14 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 10.5010.50.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 15 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. HSR10.57 |
| 16 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. HSR 10.6310.63.2 Size of Tile 600x600 mm |
| 17 | 10.63.3 Size of Tile 800x800 mm |
| 18 | Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm HSR 10.64 |
| 19 | Providing and fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. HSR 10.65 |
| 20 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. HSR 10.6710.67.2 Size of Tile 600x600 mm |
| 21 | 10.67.3 Size of Tile 800x800 mm |
| 22 | Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. HSR 10.7010.70.2 Size of Tile 600x600 mm |
| 23 | 10.70.3 Size of Tile 800x800 mm |
| 24 | 12 mm cement plaster of mix : HSR 11.511.5.4 1:6 (1 cement: 6 fine sand) |
| 25 | 15 mm cement plaster on the rough side of single or half brick wall of mix : HSR 11.611.6.2 1:6 (1 cement: 6 fine sand) |
| 26 | Providing & laying average 6mm thick POP Coatingon walls, Ceiling, beams and lintels etc. complete in all respects as approved by the Engineer-In-Charge. HSR 11.57 |
| 27 | Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete HSR 11.58 |
| 28 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : HSR 11.6411.64.1 New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 29 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. HSR 11.6611.66.2 Two coats |
| 30 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : HSR 11.6711.67.1 Water thinnable cement primer |
| 31 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. HSR 11.7511.75.2Two coats Asian (Royal shine) Premium quality. |
| 32 | Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. HSR 11.76 |
| 33 | Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc. HSR 11.77 |
| 34 | Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. HSR 11.78 |
| 35 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. HSR 12.1212.12.21.0 mm thick |
| 36 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.HSR 12.3612.36.325 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws |
| 37 | Providing and fixing ISI marked, IS : 1341, M.S. heavy weight bright finished butt hinges with necessary screws etc. complete : HSR 12.5612.56.2 100x75x3.50 mm |
| 38 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : HSR 12.9812.98.2250x16 mm |
| 39 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : HSR 12.9912.99.2250x10 mm |
| 40 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : HSR 12.10212.102.1125 mm |
| 41 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener,including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. HSR 13.2 |
| 42 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : HSR 28.15(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 43 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete HSR 30.21 |
| 44 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :HSR 30.2830.28.1One or more coats on old work |
| 45 | Providing and fixing 3mm ACP sheet with Aluminium section 1\" x 1½” (16 gauge) @ 450 mm centre to centre horizontally and including fixed in intact position ACP sheet with double side tape and stick complete in all respects including top beading / noising as per directed by Engineer-in-charge make super bond , alutech alstn, imperia) (N.S.) |
| 46 | Providing and fixing WPC door 30mm thick having minimum density 650 Kg./cum with required stainless steel fitting for door complete as per design fixed in position complete in all respect as per directed by Engineer-in-charge excluding cost of lock if required (N.S.) |
| 47 | Providing and fixing 5mm thick float plain glass with necessary beading after making space in existing WPC door N.S.i)5mm thick plain glass |
| 48 | ii) 5mm thick frosted glass |
| 49 | Providing and fixing toughen glass 12mm thick openable / fixed including all accessories/fittingsof Ozone, TaTa and provision of film as per designat site as per requirement.N.S. |
| 50 | Providing and fixing best quality WPC chowkhats size 5\" x 2½\" having minimum density 650 kg/cum with necessary hold fast / fastener etc. complete in all respects. Complete as directed by Engineering -in-charge. N.S. |
| 51 | Providing & fixing blinds Zebra make in windows. Material palyester & polyester Bend, brand Zebra blinds Complete in all respects and design approved by Engineer-in-charge. (N.S.) |
| 52 | Hacking of kotoh stone/ marble / concreate flooring including cleaning of surface etc. Complete in all respects (N.S.) |
| 53 | Providing and laying 16mm thick (minimum) parking tiles 600 x 600 mm minimum non slippery with spacerof make Kajaria / Somany / Orient / NITCO /Johnson/ Simpolo or equivalent over 20mm thick cement mortar bed 1: 4 complete in all respects (N.S.) |
| 54 | Providing and fixing panelled (marndi /marnti wood) and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) (N.S.)30 mm thick shutters |
| 55 | 20.50.220 mm internal diametre of the pipeline |
| 56 | 20.50.325 mm internal diametre of the pipeline |
| 57 | 22.1.2 White vitreous chinaware Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 58 | 22.1.2 White vitreous chinaware Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap (L.R) |
| 59 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. HSR 22.15 |
| 60 | Providing and fixing 40mm i/d G.I. waste pipe embedded in walls up to floor level including cost of union and plumber joint HSR 22.16 |
| 61 | Providing and fixing 100 mm sand cast Iron grating for gully trap. HSR 22.19 |
| 62 | Providing and fixing white vitreous chinaware pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : HSR 22.2322.23.1 W.C. pan with ISI marked white solid plastic seat and lid |
| 63 | Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : HSR 22.2622.26.3Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern |
| 64 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : HSR 22.3622.36.1 White solid plastic seat with lid |
| 65 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. HSR 22.38 |
| 66 | Providing and fixingpartitions for different type of urinals. HSR 22.5022.50.1.1.2 Single Colour |
| 67 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. HSR 22.88Internal work - Exposed on wall22.88.1 15 mm dia nominal bore |
| 68 | 22.88.220 mm dia nominal bore |
| 69 | 22.88.325 mm dia nominal bore |
| 70 | 22.88.432 mm dia nominal bore |
| 71 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): HSR 22.9422.94.220 mm nominal bore |
| 72 | 22.94.325 mm nominal bore |
| 73 | 22.94.432 mm nominal bore |
| 74 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : HSR 22.9822.98.220 mm nominal bore |
| 75 | 22.98.3 32 mm nominal bore. |
| 76 | Providing and fixing brass stop cock of approved quality : HSR 22.9722.97.2 20 mm nominal bore |
| 77 | Providing and fixing Unplasticised PVC connection pipe with brass unions : HSR 22.10122.101.245 cm length22.101.2.115 mm nominal bore |
| 78 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : HSR 22.10322.103.220 mm nominal bore |
| 79 | 22.103.325 mm nominal bore |
| 80 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : HSR 22.10422.104.115 mm nominal bore |
| 81 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 HSR 22.10822.108.115mm nominal bore |
| 82 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : HSR 22.17322.173.1 With common burnt clay non-modular bricks of class designation 7.5 |
| 83 | Supplying and fixing C.I. cover without frame for manholes : HSR 22.20022.200.1 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg |
| 84 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. HSR 22.209 |
| 85 | Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. HSR 22.22222.222.1 Single Socket Type A22.222.1.1 160mm o/d SWR UPVC pipe lines laid complete |
| 86 | 22.222.1.2 110mm o/d SWR UPVC pipe lines laid complete |
| 87 | Providing & fixing PVC floor trap (N.S.)110 mm o/d |
| 88 | Electrical Work items POINT WIRINGWiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copperconductor cable in 1.6 mm thick PVC conduit pipe.(HSR HSR-23.4.1)23.4.1.2GROUP-B |
| 89 | Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe.(HSR 23.4.2)23.4.2.2GROUP-B |
| 90 | Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch (HSR 23.4.3)23.4.3.2GROUP -B |
| 91 | POWER OUTLETSWiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required (HSR 23.4.4)23.4.4.2GROUP-B |
| 92 | Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required (HSR 23.4.5)23.4.5.2GROUP-B |
| 93 | Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects.(HSR 23.8.10)23.8.10.11 & 2 Modules including combined plate for Telephone and data |
| 94 | 23.8.10.2 3 Modules |
| 95 | 23.8.10.3 4 Modules |
| 96 | 23.8.10.4 6 Modules |
| 97 | 23.8.10.58 Modules |
| 98 | 23.22.3.2 S.P.N. or DP enclosure suitable for DP MCB |
| 99 | Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect.(HSR 23.8.11)23.8.11.15 amp 1 way switch |
| 100 | 23.8.11.2 5 amp 2 way switch |
| 101 | 23.8.11.3 15 amp 1 way switch |
| 102 | 23.8.11.45 amp Socket |
| 103 | 23.8.11.515 amp 6 pin Socket |
| 104 | 23.8.11.7 step type Fan Regulator 2 modules 300 watt |
| 105 | 23.8.11.8 telephone socket outlet modular type |
| 106 | 23.8.11.9. T.V socket outlet modular type |
| 107 | 23.8.11.10Blanking plate |
| 108 | 23.8.11.11 RJ45 computer DATA Socket outlet for CAT 6 or CAT 6e cablemodular type |
| 109 | 23.8.11.12 UPS Charger,1000mh, 5V, 1module (For Non residential use only) |
| 110 | PVC CONDUITING FOR CIRCUIT WIRINGSupply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work.(HSR 23.7.6)23.7.6.1 PVC pipe of 20mm dia |
| 111 | 23.7.6.2 PVC pipe of 25 mm dia. |
| 112 | 23.7.6.3PVC pipe of 32mm dia. |
| 113 | 23.7.6.4PVC pipe of 40 mm dia. |
| 114 | CIRCUIT WIRINGWiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable1100 Volts grade in existing MS/PVC Conduit etc as required.(23.5.6)23.5.6.11 run of Size 1.50 Sqmm(1/1.40mm) |
| 115 | 23.5.6.2 1 run of Size 2.50 Sqmm(1.1.80mm) |
| 116 | 23.5.6.3 1 run of Size 4 Sqmm(1/2.24mm) |
| 117 | 23.5.6.4 1 run of Size 6 Sqmm(1/2.80mm) |
| 118 | 23.5.6.5 1 run of Size 10 Sqmm(1/3.50mm) |
| 119 | ADOPTER BOXESSupply and erection of suitable MS/GI Box covered with 5 mm thick Bakelitesheet as below 9HSR 23.8.3)23.8.3.175 mm x 75 mm x 60 mm deep M.S. box |
| 120 | 28.8.3.2100 mm x 100 mm x 60 mm deep M.S. box |
| 121 | WIRING FOR LV SYSTEMSupply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existingpipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work.(HSR 23.23.8)(23.23.8.1)2 pair telephone wire |
| 122 | (23.23.8.2) 4 pair telephone wire |
| 123 | Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required (HSR 23.23.9) |
| 124 | Supplying and drawing of 1 no UTP 4 pair CAT Sa LAN Cable in the existingsurface/recess MS/PVC conduit as required (HSR 23.23.10) |
| 125 | DISTRIBUTION BOARDSSupply and erection of double door sheet steel enclosure distribution boardsuitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respectup to the entire satisfaction of the Engineer-in-Charge of the work. (HSR 23.22.4)23.22.4.5 TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) For Flood Lights on Terrace and Acs in rooms. |
| 126 | 23.22.4.6TPN DB Horizontal type Double Door 6 way ( 8 incoming 3phase*6 outgoing) -For Light |
| 127 | 23.22.4.7 TPN DB Horizontal type Double Door 8 way ( 8 incoming 3phase*8 outgoing)-For Power |
| 128 | MCBsSupply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- (HSR 23.22.5)23.22.5.16 amp. to 32 amp Single Pole |
| 129 | 23.22.5.36 amp to 32 amp. Double POLE |
| 130 | 23.22.5.840 amp to 63 amp. MCB\"s FOUR POLE |
| 131 | Dismantling old wiring points ( surface wiring system ) including necessary repairs to wall etc. HSR 23.25.123.25.1.1 Light, fan or call bell Point including circuit/sub main wiring |
| 132 | 23.25.1.2 Wall socket point including circuit/submain wiring |
| 133 | CABLE TRAYSupply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work.(HSR-23.23.6) (23.23.6.2)MS perforated cable tray painted with powder coating 200 X 50X2mm |
| 134 | (23.23.6.3) MS perforated cable tray painted with powder coating 375 X 50X2mm |
| 135 | CABLE LAYINGLaying and fixing of cable on surface/ cable tray etc as required:-(HSR 24.2.5)24.2.5.2 16 Sq mm to 35 sqmm 2 to 4 Core |
| 136 | 24.2.5.3 50Sq mm to 150 sqmm 2 to 4 Core |
| 137 | WIRE TERMINATIONSSupply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. (HSR 24.2.6)24.2.6.11.5 Sqmm |
| 138 | 24.2.6.22.5sqmm |
| 139 | 24.2.6.34.0sqmm |
| 140 | 24.2.6.46.0sqmm |
| 141 | 24.2.6.5 10.0sqmm |
| 142 | HDPE PIPES/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. (HSR 24.5.2)24.5.2.4DWC/HDPE pipe 90/75 mm outer dial inner dia |
| 143 | FIXTURESsupplying ,fixing , testing & commissioning of various type lighting fixtures as follows. Make PHILIPS/HAVELLS /LUMILUX/SURYA2\"X2\" LED downlight suitable with 36 w LED with remote Led driver.6500 k (NS) |
| 144 | (III) 15Watt Round LED surfaceDownlighter ,aluminium hausing with integrated driver,NEO HE DL Surface,fixture size in dia 234 mm,Height 57 mm. Make PHILIPS/HAVELLS /LUMILUX/SURYA(N.S) |
| 145 | (iv) Mirror light led 10 watt ,surface and wall mounted batten type. Make PHILIPS/HAVELLS /LUMILUX/SURYA(N.S) |
| 146 | S/E/I/T/Cof following sizes of energgy saving type ceiling fan 1200 mm ,72 watt double ball bearing. motor, blades, downrod, canopy, capacitor, etc. suitable for operation on 230 volts 50 Hz A.C. supplyrequired to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work Make-USHA/HAVELLS /LUMILUX?CROMPTON, (NS) |
| 147 | (vii)Exhaust Fan (White) Ceiling mounted Exhaust Fan 300 x 300mm ,Motor speed 2000 RPM,6 blade,including the cost of labor andmaterials required to complete the job in all respect upto the enter satisfaction of enginnering incharge of the work. Make-USHA/HAVELLS /LUMILUX?CROMPTON, (NS) |
| 148 | Supply installation testing and commssioning of 300X300MM sq 20 watt ceiling surface penal light (6500 KA)required to complete the job in all respect upto the satisfaction of enginnerin in incharge of the work Make PHILIPS/HAVELLS /LUMILUX/SURYA(N.S) |
| 149 | Supply installation testing and commssioning of 1.5 TON3 star cassete AC with cordless remote, 30 feet copper pipe, drain pipeincluding the cost of labor andmaterials required to complete the job in all respect upto the enter satisfaction of enginnering incharge of the work.Make/OGENERAL/DAKEN/BLUE STAR with 5kva stabilizer Make-V-Guard/Philips/Microtek (NS) |
| 150 | Supply installation testing and commssioning of focus15 watt ceiling surface mountl light (6500 KA)required to complete the job in all respect upto the satisfaction of enginnerin in incharge of the work Make PHILIPS/HAVELLS /LUMILUX/SURYA(N.S) |
| 151 | SITC of 16\" wall fan including the cost of labor andmaterials required to complete the job in all respect upto the enter satisfaction of enginnering incharge of the work. Make-USHA/HAVELLS /LUMILUX?CROMPTON, (NS) |
| 152 | Supply installation testing and commssioning of 50 Watt water proof flood light including the cost of labor andmaterials required to complete the job in all respect upto the enter satisfaction of enginnering incharge of the work.Make PHILIPS/HAVELLS /LUMILUX/SURYA(N.S) |
| 153 | Supply installation testing and commssioning of 5 Watt outdoor garden LED lightwaterproof (3500k) including the cost of labor andmaterials required to complete the job in all respect upto the enter satisfaction of enginnering incharge of the work.Make PHILIPS/HAVELLS /LUMILUX/SURYA(N.S) |
