|
| 1 | Making plinth protection 50mm (fifty millimetre) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm (twenty millimetre) nominal size) over 75mm (seventy five millimetre) thick bed of dry brick ballast 40 mm (forty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 2 | Constructing Course rubble stone masonary hammer dressed \"U\" shape open surface drain with side wall. 15x22 cm (fifteen into twenty two centimetre) in cement mortar 1:6 (One Cement : Six Sand) and inside plastring with cement plaster 1:3 (One Cement : Three Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (One Cement : Five Sand : Ten graded stone aggregate) of 40 mm (forty millimetre) nominal size) and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (One Cement : Two Sand : Four Graded stone aggregate of 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 3 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor all level in all shapes and sizes in : Cement mortar 1:6 (One cement : Six coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 4 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor all level. Cement mortar 1:4 (One cement : Four coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 5 | Providing and laying 20 cm (twenty centimetre) thick composit stone masonry with stone facing of Ashler punched stones in cement mortar 1:6(one cement : six sand) and concrete backing with cement concrete 1:3:6 (one cement: three sand: six graded stone aggregate 20 mm (twenty millimetre) nominal size) on inner face of walls including centring,shuttering and propping complete up to floor all level including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 6 | Providing and fixing 18 mm (eighteen millimetre) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimetre) thick base cement mortar 1:4 (one cement : four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade:Area of slab over 0.50 Per squaremetre (zero point fifty square metre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 7 | Providing edge moulding to 18 mm (eighteen millimetre) thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work including all leads, lifts and carriage of materials and other incidentals. |
| 8 | Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge including all leads, lifts and carriage of materials and other incidentals. |
| 9 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). in second class deodar wood including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 10 | Providing 40x5 mm (forty into five millimetre) flat iron hold fast 40 cm (forty centimetre) long including fixing to frame with 10 mm (ten millimetre) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre) 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 20mm (twenty millimetre) nominal size) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 11 | Providing and fixing 40 mm (forty millimetre) thick glazed shutters for doors, windows and clerestory windows using 4 mm (four millimetre) thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. In 2nd class deodar wood including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 12 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm (thirty five millimetre) thick including ISI marked Stainless Steel butt hinges with necessary screws including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 13 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm (twenty five millimetre to forty millimetre) thick : 4 mm (four millimetre) thick glass pane (weight not less than 10 (ten) Per Kilogram per Per squaremetre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 14 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four millimetre) in both directions with wire of dia 0.63 mm (zero point sixty three millimetre), for doors, windows and clerestory windows with hinges and necessary screws : 35 mm (thirty five millimetre) thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size. Second class deodar wood including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 15 | Providing and fixing 18 mm (eighteen millimetre) thick, 150 mm (one hundred fifty millimetre) wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm (six millimetre) coir veneer board, nickle plated M.S. Pipe 20 mm (twenty millimetre) dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm (twenty five into three millimetre) M.S. Flat 10 cm (ten centimetre) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm (one hundred millimetre into forty millimetre into forty millimetre) on both inner side of pelmet and rawl plugs 75 mm (seventy five millimetre) long etc. all complete. Extra for using veneered particle board conforming to IS 3097 Grade I, in item of pelmet 18mm (eighteen millimetre) thick 150mm (one hundred fifty millimetre) wide. Particle board with decorative veneering on both sides including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 16 | Providing and fixing teak wood lipping of size 25x3 mm (twenty five into three millimetre) in pelmet including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 17 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 18 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 Per Kilogram (thirty five kilogram) and door width upto 700 mm (seven hundred millimetre), with necessary accessories and screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 19 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 20 | 300x16 mm (three hundred into sixteen millimetre) |
| 21 | 250x16 mm (two hundred fifty into sixteen millimetre) |
| 22 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 23 | 250x10 mm (two hundred fifty into ten millimetre) |
| 24 | 200x10 mm (two hundred into ten millimetre) |
| 25 | 100X10 mm (one hundred into ten millimetre) |
| 26 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 27 | 125mm (one hundred twenty five millimetre) |
| 28 | 100mm (one hundred millimetre) |
| 29 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 30 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.Double strip (horizontal type) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 31 | Providing and fixing 150mm (one hundred fifty millimetre) bright finished brass hard drawn hooks and eyes including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 32 | Providing and fixing 19 mm (nineteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cup board / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from out side shall be finished with 4 mm (four millimetre) thick vaneer Ply of approved shade to match with panelling including stainless steel hinges hinges and magnetic catcher with in all accessories etc. complete as per detailed drawing as per direction of Engineer-in-charge including all leads, lifts and carriage of material and other incidental. |
| 33 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, Per Kilogram railings, brackets, gates and similar works including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 34 | Providing and fixing 75mm x60mm (seventy five millimetre into sixty millimetre) moulded hand rails in straight length complete in 1st class Indian Teak wood including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 35 | Kota stone 25 mm (twenty five millimetre) thick slab flooring over 20 mm (twenty millimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 36 | Kota stone slabs 20 mm (twenty millimetre) thick in risers of steps, skirting, dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 37 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (three hundred into three hundred millimetre) (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimetre) thick bed of cement mortar 1:4 (one Cement : four Coarse sand), jointing with grey cement slurry @ 3.3 Per Kilogram/ sq.m (three point three kilogram per square metre) including pointing the joints with white cement and matching pigments etc., complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 38 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm (twelve millimetre) thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3Per Kilogram per Per squaremetre (three point three kilogram per square metre) including pointing in white cement mixed with pigment of matching shade complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 39 | Providing and laying 600X600 mm(six hundred into six hundred millimetre) vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours andshades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 Per Kilogram/ Per squaremetre including grouting the joints with white cement and matching pigments etc., completeincluding all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 40 | Providing and laying 600x600mm (six hundred into six hundred millimetre) Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 Per Kilogram/ Per squaremetre (three point three kilogram per square metre)including grouting the joint with white cement & matching pigments etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 41 | Providing and fixing wooden Laminated flooringof G4 grading made in superior water Resistant High Density hard wood fibre board with complete all accessories including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 42 | Providing and fixing 0.62mm (zero point sixty two millimetre) thick troughed prepainted steel sheet roofing, with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating, including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including all leads, lifts and carriage of materials and other incidentals. |
| 43 | Providing ridges or hips of width 60 cm (sixty centimetre) overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm (eight millimetre) dia G.I. limpet and bitumen washers complete. 0.63 mm (zero point sixty three millimetre) thick with zinc coating not less than 275 gm/m² (two hundred seventy five gram per square metre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 44 | Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)including all leads, lifts and carriage of materials and other incidentals. |
| 45 | 15 mm (fifteen millimetre) cement plaster on rough side of single or half brick wall of mix: 1:6 (one cement: six coarse sand)including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 46 | 6mm (six millimetre) cement plaster of mix: 1:3 (one cement :three Fine sand) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 47 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat withcement primer including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 48 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre (fifty gram/litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.:New work (Two or more coats applied @ 1.43 litre/ 10 Per squaremetre (one point forty three per ten square metre). Over and including priming coat of exterior primer applied @ 0.90 litre/10 Per squaremetre (zero point ninety litre per ten square metre) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 49 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 Per squaremetre (zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.75 ltr/10 Per squaremetre (zero point seventy five litre per ten square metre) of approved brand and manufacture including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 50 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 Per squaremetre (zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 Per squaremetre (zero point eighty litre per ten square metre) of approved brand and manufacture including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 51 | Providing and applying white cement based putty of average thickness 1 mm (one millimetre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 52 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 53 | 15 mm (fifteen millimetre) nominal bore |
| 54 | 20 mm (twenty millimetre) nominal bore |
| 55 | Making connection of G.I. distribution branch with G.I. main of 25 to 40 mm (twenty five to forty millimetre) nominal bore size by providing and fixing tee, including cutting and threading the pipe etc. completeincluding all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 56 | Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 57 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 58 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 59 | Providing and fixing viterous China Cat. No. S1013164 One-piece EWC S with slim seat cover & fitting685 x 360 x 720 mm (six hundred eighty five into three hundred sixty into seven hundred twenty millimetre) White ShadeWall hung of Cera or equivalentcomplete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 60 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredincluding all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 61 | Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimetre) dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mm (five hundred fifty into four hundred millimetre) with a 15 mm (fifteen millmetre) CP Brass single hole basin mixer including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 62 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 63 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm (five hundred eighty into three hundred eighty into three hundred fifty millimetre) with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required single half stall urinal with 5 (five) litre P.V.C. automatic flushing cistern including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 64 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm (forty millimetre), including painting of fittings and brackets, cutting and making good the walls wherever required, Kitchen sink without drain 610x510 mm (six hundred ten into five hundred ten millimetre)bowl depth 200 (two hundred) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 65 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm(forty millimetre) dia including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 66 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm (forty five centimetre) length 15 mm (fifteen millimetre) nominal bore including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 67 | Providing and fixing PTMT grating of approved quality and colour Circular type. 125 mm (one hundred twenty five millimetre) nominal dia with 25 mm (twenty five millimetre) waste hole including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 68 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete new work 40mm (forty millimetre) dia including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 69 | Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 70 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm (fifteen millimetre) nominal bore including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 71 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 72 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 73 | Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimetre), breadth 102mm (one hundred two millimetre), height of 75mm (seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grams) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 74 | Providing and fixing 8 mm (eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 (one) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including all leads, lifts and carriage of materials and other incidentals. |
| 75 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 76 | 15mm (fifteen millimetre) |
| 77 | 20mm (twenty millimetre) |
| 78 | Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1000 ltr (one thousand litre) tank including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 79 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm (fifteen millimetre) nominal bore including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 80 | Providing and fixing 110 mm (one hundred ten millimetre) high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 81 | Providing and fixing 150 mm (one hundred fifty millimetre) high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 82 | Providing and fixing 110 mm X 90 mm (one hundred ten millimetre into ninety millimetre) PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 83 | Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 84 | 110mm (one hundred ten millimetre) dia |
| 85 | 150 mm (one hundred fifty millimetre) dia |
| 86 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 87 | 110mm (one hundred ten millimetre) dia |
| 88 | 150 mm (one hundred fifty millimetre) dia |
| 89 | Providing and fixing110mm (one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 90 | Providing and fixing110mm (one hundred ten millimetre) dia PVC collars ISI marked including fixing with approved adhesive etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 91 | Providing and fixing 110mm (one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 92 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slabwith 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm (ninety into eighty centimetre) and 45 cm (forty five centimetre) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover and frame to be not less than 38 Per Kilogram (thirty eight kilogram) (weight of cover 23 Per Kilogram (twenty three kilogram) and weight of frame 15 Per Kilogram (fifteen kilogram)) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
| 93 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size) cement plastered on both sides with cement mortar 1:3 (one cement : three coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm (one hundred to two hundred fifty millimetre) diameter including all leads, lifts and carriage of materials and other incidentals as per direction of Engineer-in-Charge. |
