|
| 1 | PROVIDING AND FIXING CROSS TRAINER including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BELOWDIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height). SAFE AREA:- 1.77 x 1.2Mtr. Cross trainer equipment made from “B” Class G.I. Pipe of different NB. The main frame Pipes are of 80NB “B” Class G.I. Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The Handle Frame is made up of 25NB “B” Class G.I.Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mmCRC square pipes of 3mm thickness. To build structure bushes are used which are made from M.S.seamless pipe of 60mm OD. With 5 mm thickness. The footrests are made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mm x 310mm x 3mm thick closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright . The Bearings used are of “6007zz” “6205zz” and“6203zz”permanent lubricated sealed bearing ofreputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The powder coating is done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70Micron thickness. A16 , A 24 mm circlips are used for assembly.Bolt M8X16 mm and NY lock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance. |
| 2 | PROVIDING AND FIXINGSEATED PULLAR including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BELOWDIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height). SAFE AREA:- 1.2Mtr x 3MtrSeated puller equipment made up of “B” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetersThe center pipe is of 100NB made from “B” Class G.I. pipe. Bottom support is of M.S. round plate of Ø 250 mm & 10mm thickness is welded. All linkages are made up of 25NB “B” class G.I. pipe.The handle frame is of 32NB “B” class G.I. pipe.The seat frame is of 32NB “B” class G.I. pipe, To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class.Welded with M.S. round plate of Ø250 mm & 10mm thick.Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap is made fromFRPMaterial with 0.7 mm Thickness. The seats and Back rests are fitted on the outer frames are made up of M.S.Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of“ 6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for assembly are of A16 The powder coating donewith Pure Polyester powders ofAckzonoble or Berger Paints with 60 to 70 micron thickness. Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% Cst, Transportation & Fitting charges transit insurance. |
| 3 | PROVIDING AND FIXING CHEST PRESS including filling and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BELOWDIMENSIONS: - 2000mm (Length) x 710mm (Width) x 2200mm. (Height) SAFE AREA: - 3.0Mtr x 1.7Mtr. Chest press equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The center pipe is of 100NB made up of “B” Class G.I. pipe. The bottom welded with support of M.S. round plate of Ø250 mm & 10mm thickness.The connecting pipes are made up from 25NB “B” class G.I. pipe. The handle frame is made up from 32NB “B” class G.I. pipe. To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S.angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap is made fromFRPMaterial with 0.7thickness. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The bearings used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly.The cerclips used for locking is made up of A24 mm & A16mm. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CSt, Transportation & Fitting charges transit insurance. |
| 4 | PROVIDING AND FIXING LEG PRESS including filling and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BELOWDIMENSIONS: - 1840mm (Length) x 360mm (Width) x 1560mm. (Height). SAFE AREA:- 2.8 x 1.4Mtr. Leg Press equipment made from“B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetersThe center pipe is of 100mm NB made from“B” Class G.I. pipe.The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm This sleevecan be disassembled from main frame.The bottom support of M.S. round plate of Ø250 mm & 10mm thick.The remaining outer frame is of 32NB made from “B” class G.I. pipe.The foundation used for fixing is structure and made from center pipe of G.I. of 80mm NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness.Seat & Back rest provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. The frame of footrests made up of 25 NB “B” class G.I. pipe.Closing Caps are made up of high quality Fiber reinforced Plastic material.To build structure bushes are used which are made from M.S. seamless pipe of 50mm O.D. and 5mm thickness. The pins used are made up of Ø25 mm SAE 8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed Brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly are of A24 mm.The powder coating done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance. |
| 5 | PROVIDING AND FIXING PARALLEL BARS including filling and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BELOW DIMENSIONS: - 1870mm (Length) x 530mm (Width) x 2000mm. (Height).SAFE AREA: - 5.0Mtr x 2.5Mtr ParallelBar equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.The main frame made from 50NB “B” Class G.I. pipe.The handle frame is of 32NB made from “B” Class G.I. pipe.The foundation used for fixing is 25mm x 25mm x 3mm thickness LAngle.Closing Caps are made up of high quality Fiber reinforced Plastic material.The powder coating done with Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance. |
| 6 | PROVIDING AND FIXING SURF BOARD including filting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS: - 910mm (Length) x 860mm (Width) x 1400mm.(Height). Safe Area:-1.39 x 1.27Mtr. Surf Board Equipment made from “B” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The center pipe is of 100mm NB made from “B” class G.I. pipe.The sleeve pipe is of 125mm OD seamless pipe with thickness of 5mm and bolted to main frame with M10 SS bolts. The bottom support welded of M.S. plate of Ø 250 mm & 10mm thickness. The handle frame is of25NB made from “B” class G.I. pipe. The paddleframe is of50NB made from “B” class G.I. pipe is supported with70 X 8mm bend M.S. flat and can be replaceable.The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB“B” classwelded with M.S. round plate of Ø250 mm & 10mm thick.Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x40mm CRC square pipes of 3mm thickness. Bushes are used 70mm Outer Diameter with 5mm thickness is used. The footrests made from Aluminum casting material of size 320mmX270mmX5mm. For support to footrest 200mmX250mm with 3mm thickness M.S. Plate used.Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø35 mm SAE 8620 bright material. The bearing used are of “6007zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly is of A34. The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness. Includes as The cost/unit ie. Rate include basic item cost 6% Excise and 5% Vat, Transportation & Fitting charges transit insurance. |
| 7 | PROVIDING AND FIXING SKY WALKER including filting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWEDIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height) SAFE AREA: - 2.7Mtr x 1.6Mtr.Sky Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetersThe main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radiusof 250mm. The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle. The handle frame is of 25mm NB made from “B” Class G.I. pipe.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class.Welded with M.S. round plate of Ø250 mm & 10mm thick.Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support.The footrests made from Aluminum casting material of size 130 X 310 X 5mm. Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø 25mm SAE8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball.The bearings used are “6205zz” are permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly.The cerclips used for assembly are of A24 type.The powder coating is done with Pure Polyester powderof Ackzonoble or Berger with 60 to 70 mic thickness.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance. |
| 8 | PROVIDING AND FIXING TRIPLE STANDING TWISTER including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWEDIMENSIONS: - 1150mm (Length) x 1150mm (Width) x 1580mm. (Height).SAFE AREA: - Ø2.1MtrTriple Twister made from “B” Class Galvanized Iron (G.I.) Pipe ofdifferent NBstands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.The Center Pipe is of 100NB made from “B” Class G.I. Round Pipe.The bottom support welded is of M.S. round plate of Ø250 mm & 10mm thick.The standing frame is of 32NB made from “B” class G.I. pipe.The handle frame of triple twister is of 25 mm NB made from “B” class G.I. pipe.The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB “b” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness The standing plate is fitted on the frame made up of Ø 80 NB GI. pipe. M.S. Round Plate of size Ø300mm x 10mm thickness.Closing Caps are made up of high quality Fiber reinforced Plastic material.The Pins used are made up of Ø 35 mm SAE 8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand.High tensile steel with galvanized nuts & bolts are used for assembly.The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance. |
| 9 | PROVIDING AND FIXING AIR WALKER including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE DIMENSIONS :- 1060mm (Length) x 810mm (Width) x 1600mm. (Height). SAFE AREA: - 2.0 Meter x 1.8 MeterAir Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm.The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be easily disassembled from main frame.The bottom support of M.S. round plate of Ø250 mm & 10mm thick.The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link is supported with MS flat of size 60X8mm.The handle frame is of 25NB made from “B” Class G.I. pipe.The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap is made fromFRPMaterial with 0.7 mm thickness.Closing Caps are made up of high quality Fiber reinforced Plastic material.Pins used of Diameter 25mm are made up from SAE 8620 bright material. A24 circlips areused for assembly.The bearings used are “6205zz” permanent lubricated sealed bearing of repute brand.High tensile steel galvanized nuts & bolts are used for assembly.The powder coating is done by Pure Polyester powder of Ackzonoble or Berger Paints with 60 to 70 micron thickness. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate.To build structure bushes are used which are made from M.S.seamless pipe of 60mm O.D.and 5mm thickness as well as 60mm diameter solid bar bush is used.Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance. |
| 10 | PROVIDING AND FIXING KNEE HIP RISER including fitting and FIXTURES, CIVIL WORKS AND REQUIRED SAND PIT FILLED WITH APPROVED SAND WORK TO BE DONE AS PER THE INSTRUCTION OF ENGINEER INCHARGE AND SPECIFICATION GIVEN BLOWE PRODUCT DIMENSIONS: - 2300mm (Length) x 600mm (Width) x 2200mm (Height).SAFE WORKOUT AREA: - 4000mm (Length) x 1600mm (Width). Knee/hip raise on parallel bars equipment made from “B”Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetersThe main frame is 100NB made from “B”Class G.I. pipe. M.S. round plates of Ø250 mm & 10mm thickness are welded at bottom. The handle frame is of 32NB, 60 mm NB and made from “B” Class G.I. pipe and 40mm x 80mm x3mm thick MS pipe for flat surface, 20mm x 40 mm MS pipe used for flat back rest. The bottom support of handle is made from 80mm x 40mm x 3mm thickness square CRC pipe.The foundation used for fixing structure having hole pass provision. The parallel bars are made from 25mm dia solid ms bar with ms square pipe support. Closing Caps made from top quality Fiber reinforced Plastic material with 2 mm thickness.High tensile steel with galvanized nuts & bolts are used for assembly.The powder coating done with Pure Polyester powders with 60 to 70 micron thickness.Includes as The cost/unit ie. Rate include basic item cost 12.5% Excise and 5% CST, Transportation & Fitting charges transit insurance. |
