Supply And Fixing Of Sports And Gym Equipment 1 • SITC open gym equipment of following DIMENSIONS: - 2000mm (Length) x 670mm (Width) x 1850mm. (Height).• SAFE AREA:- 1.2Mtr x 3Mtr Seated puller equipment made up of “C” Class G.I. pipe of different NB. N-Rajasthan

Supply And Fixing Of Sports And Gym Equipment 1 • SITC open gym equipment of following DIMENSIONS: - 2000mm (Length) x 670mm (Width) x 1850mm. (Height).• SAFE AREA:- 1.2Mtr x 3Mtr Seated puller equipment made up of “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The center pipe is of 100NB pipe. • Bottom support is of M.S. round plate of Ø 248 mm & 9mm thickness is welded.• All linkages are made up of 25NB pipe.• The handle frame is of 32NB pipe. • The seat frame is of 32NB pipe.• To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used.•The foundation used for fixing is a structure and made from center pipe of 80 NB pipe welded with M.S. round plate of Ø248 mm & 9mm thick. Main pipe supported with 23 mm X 23mm M.S. angles of 1.8 mm thickness and 19mm x 39mm M.S. square pipes of 1.8mm thickness.• Base Cover Cap is made from high quality HDPE/LLDPE material in attractive colors. • The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX1.8mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. • Closing Caps are made up of high quality HDPE/LLDPE material in attractive colors. • Pins used of Diameter 25mm and 17mm are made up from bright material.• The bearings used are of “ 6205” and “6203” permanent lubricated sealed bearing of reputed brand.• High tensile steel with galvanized nuts & bolts are used for assembly.• The P.U. bushes (Stopper) used to avoid the collision.• The cerclips used for assembly are of A16.Complete in all respect including discryption board of the equipment.• Handle grips are provided which are made of high quality rubber material.• The powder coating done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness. A separate direction board of 1’x1’ made of SS on M.S. angle stand. 4 Nos 107000.00 0.00 0.0000 2 • SITC open gym equipment of following DIMENSIONS: - 1840mm (Length) x 360mm (Width) x 1560mm. (Height).• SAFE AREA: - 2.8 x 1.4Mtr.• Leg Press equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The center pipe is of 100mm NB made from “C” Class G.I. pipe.• The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be disassembled from main frame.• The bottom support of M.S. round plate of Ø250 mm & 10mm thick.• The remaining outer frame is of 32NB made from “C” class G.I. pipe.• The foundation used for fixing is structure and made from center pipe of G.I. of 80mm NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness.• Seat & Back rest provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm.• The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate.• The frame of footrests made up of 25 NB “C” class G.I. pipe.• Closing Caps are made up of high quality Fiber reinforced Plastic material.• To build structure bushes are used which are made from M.S. seamless pipe of 50mm O.D. and 5mm thickness.• The pins used are made up of Ø25 mm SAE 8620 bright material.• The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed Brand. • High tensile steel with galvanized nut bolts are used for assembly.• The cerclips used for assembly are of A24 mm.• The powder coating done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness.Complete in all respect including discryption board of the equipment. 4.00 Nos 78000.00 0.00 0.0000 3 • SITC open gym equipment of following DIMENSIONS: - 1650mm (Length) x 700mm (Width) x 1650mm.(Height)• SAFE AREA: - 2.7Mtr x 1.6Mtr. • Sky Walker Equipment made from “C” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The main frame pipe is of 80mm NB pipe which is bend at the radius of 250mm.• The leg movement frame is of 48 x 48mm x 2.8mm thick M.S. square pipe.• Sleeves are made up of 98 mm OD M.S. pipe with thickness 3mm. This results in easy replacement of bearings, pins and handle. • The handle frame is of 25mm NB pipe. • The foundation used for fixing is a structure and made from center pipe of 80 NB pipe welded with M.S. round plate of Ø248 mm & 9mm thick. Main pipe supported with 23 mm X 23mm M.S. angles of 1.8mm thickness and 19mm x 39mm M.S. square pipes of 1.8mm thickness. Two foundations are provided for rigid support.• The footrests made from HDPE/LLDPE material of size 130 X 310 X 5mm in attractive colors. • Closing Caps are made up of high quality HDPE/LLDPE material in attractive colors.• The pins used are made up of Ø 25mm bright material. Pins are fixed at the outer end with M8 grub screws and Dia.7.8mm ball.• The bearings used are “6205” are permanent lubricated sealed bearing of reputed brand.• High tensile steel with galvanized nuts & bolts are used for assembly. • Handle grips are provided & it is made up of high quality rubber material.• The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness.Complete in all respect including discryption board of the equipment. 4.00 Nos 105000.00 0.00 0.0000 4 • SITC open gym equipment of following PRODUCT DIMENSIONS: - 1950mm (Length) x 1350mm (Width) x 700mm (Height).• SAFE WORKOUT AREA: - 2500mm (Length) x 1600mm (Width).• The Sit up Board double made from “C” Class GI pipe. Center column made from 100mm NB “C” class G.I. Pipe.• Sleeve provided of M.S. seamless pipe of Outer diameter 123mm with thickness 3mm provided. • The main frame is of 50mm NB pipe. FRP sheet of 3mm thickness is molded on main frame. • The remaining frame of the sit up board is of 32mm NB pipe.• Closing Caps are made up of high quality HDPE/LLDPE material in attractive colors.• Fiber reinforced Plastic sheet of 3mm thickness is Bounded on 25mm NB pipe of main frame. • The foundation used for fixing is a structure and made from center pipe of 80 NB pipe welded with M.S. round plate of Ø249 mm & 9mm thick. Main pipe supported with 23 mm X 23mm M.S. angles of 1.8 mm thickness and 19mm x 39mm M.S. square pipes of 1.8 mm thickness.• The powder coating is done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness.Complete in all respect including discryption board of the equipment. 4 Nos 72000.00 0.00 0.0000 5 SITC open gym equipment of following DIMENSIONS: - 1800mm (Length) x 650mm (Width) x 2150mm. (Height).• SAFE AREA: - 3.0Mtr x 1.7Mtr.• Chest press equipment made up of “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The bottom welded with support of M.S. round plate of Ø248 mm & 9mm thickness. • The connecting pipes are made up from 25NB pipe.• The center pipe is of 100NB pipe • The handle frame is made up from 32NB pipe.• To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. • The foundation used for fixing is a structure and made from center pipe of 80 NB pipe, Welded with M.S. round plate of Ø248 mm & 9mm thick. Main pipe supported with 23 mm X 23mm M.S. angles of 1.8 mm thickness and 19mm x 39mm MS square pipes of 1.8mm thickness.• The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX1.8mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.• Closing Caps are made up of high quality HDPE/LLDPE material in attractive colors. • Base Cover is made up of high quality HDPE/LLDPE material in attractive colors.• Pins used of Diameter 25mm and 17mm are made up from bright material.• Bolt M8X16 mm and Nylock nut of M8 made of SS material is used on nylon cap mounted on pins to Protect bearings and pins from rain and dust.• The bearings used are of “6205” & “6203” permanent lubricated sealed bearing of reputed brand • The cerclips used for locking is made up of A24 mm & A16mm.• High tensile steel with galvanized nuts & bolts are used for assembly.• Handle grips are provided which are made of high quality rubber material.• The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness.Complete in all respect including discryption board of the equipment. 4.00 Nos 110000.00 0.00 0.0000 6 • SITC open gym equipment of following DIMENSIONS: - 2250mm (Length) x 750mm (Width) x 1400mm.(Height). • Safe Area: - 3.0Mtr x 1.8Mtr. • Air Walker cum seating cum standing twister Equipment made from “C” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. • The main frame of 100NB pipe. • The bottom support frame of M.S. 38mm x73mmx4.5mm thick C Channel. • The seating movement seat 20mm NB & 25mm NB pipes used for support frame. • The handle frame is of 25NB pipe. • Closing Caps are made up of high quality HDPE/LLDPE material in attractive colors. • Pins used of Diameter 25mm are made up from bright material. • The bearings used are “6205” permanent lubricated sealed bearing of reputed brand. • High tensile steel galvanized nuts & bolts are used for assembly. • A24 cerclips are used for assembly. • 298mm diameter x 9mm thick plate used for rotating seat of seating twister with 50NB pipe. • To build structure bushes are used which are made from seamless pipe of 60mm O.D. And 5mm thickness as well as 60mm diameter solid bar is used. • The footrests made from HDPE/LLDPE material of size 130 X 310 X 5mm in attractive colors, with the support of 245mm X 105mm X 2.8mm thick MS plate.. • The Equipment has Bolting provision for mounting on concrete slab. • The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with minimum 60 to 70 micron thickness. 4.00 Nos 110000.00 0.00 0.0000 7 • Age Group: - 4 -12 Years. • Area: - 0.5 M X 3.5 M • Safe Play Area: - 1.5 M X 5.0M • Platform Height: - 1.5 M • Product Height: - 1.9 M • FRP Wave Slide Play Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetres.• Slide chute made from best quality FRP (Fibre Reinforced Plastic) in attractive colours which is supported by Diameter 25 NB “B” class G.I. pipe.• Slide Platform (Anti -skid) is of height 1.5 metre is made from high strength G.I. sheet of thickness 1.5mm which is supported by Diameter 40mm NB “B” class G.I. pipe.• The platform railing made from Diameter 20mm NB “B” class G.I. bend pipe. • The ladder frame made from Diameter 25 mm NB “B” class G.I. pipe. The ladder railing made from Diameter 20mm NB “B” class G.I. pipe. • Ladder steps made in a triangular shape from high strength G.I. sheet of thickness 1.5mm. The width of the step is 90mm and the distance between two steps is 250mm. • High tensile steel galvanized Nuts, Bolts & Washer are used for assembly. • The powder coating is done by Pure Polyester powder of Ackzonoble or Berger Paints with 60 to 70 micron thickness. 5.00 Nos 85000.00 0.00 0.0000 8 • Age Group: - 3 - 10 Years. • Area: - Φ 1.2 M • Safe Play Area: - Φ 2.5 M • Platform Height: - 0.9M • Four Seater M.G.R. Play Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetres. • The main frame is made up of Φ40mm NB “B” class G.I. pipe which is welded to M.S. round plate of Φ250 X10 mm thickness. This main frame supported by Φ32mm NB “B” class G.I. pipe.• The M.G.R. stand is made from Φ80mm NB “B” class G.I. pipe. • For M.G.R. “6209” bearings are used which are of reputed make. • The seats attached shall be made out of best quality F.R.P. material in attractive shape with attractive colours. These seats are safely mounted on bend pipe of Φ20mm NB “B” class G.I. bend pipe and M.S. flat of 40X5mm. • High tensile steel galvanized Nuts, Bolts & Washer are used for assembly. • The powder coating is done by Pure Polyester powder of Ackzonoble or Berger Paints with 60 to 70 micron thickness. 5.00 Nos 60000.00 0.00 0.0000 9 • Age Group: - 3–8 Years.• Area: - 2.2 M X 2.7 M• Safe Play Area: - 3.4 M X 3.9 M• Platform Height: - 1.3M• Combination set (3 in 1)Play Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimetres. • Main Square frame structure made from Φ32mm NB “B” Class GI pipe. • Step ladder made up of in Φ25mm NB “B” Class GI pipe. • Step ladder Railing made up of in Φ20mm NB “B” Class GI pipe.• Mini wave slide chute shall be made up of 5mm thick made of Fiber Reinforced Plastic with self-pigment colour. Slide is supported by Φ25mm NB “B” class G.I. pipe. • Slide Platform (Anti-skid) is of height 1.0 metre is made from high strength G.I. sheet of thickness 1.5mm which is supported by Diameter 40mm NB “B” class G.I. pipe. • The platform railing cum handle made from Diameter 20mm NB “B” class G.I. bend pipe. • See-Saw Seat shall be made up of 5mm thick made of Fiber Reinforced Plastic with self-pigment color. • See-Saw frame structure made from Φ32mm NB &Φ20MM NB “B” Class GI pipe. • The Sea Saw U-bend support is made from Φ20mm NB “B” class G.I. pipe. • The bearings are used “6202zz” are of reputed make. • Seamless Bushes are made from M.S. seamless pipe of Φ60mm OD and thickness of 5mm. • Swingleg support pipe made from Diameter 32mm NB “B” class G.I. pipe. • The bearings used are “6202zz” permanent lubricated sealed bearing of reputed brand. • To build structure bushes are made from M.S.seamless pipe of Diameter 50mm O.D. And 5mm thickness solid bar is used. • Pins are used of Φ20mm are made up from solid bright bar material. • F.R.P. seats (AntiSkid) are connected to top pipe with 6 mm rubber coated chain. • High tensile steel galvanized Nuts, Bolts &Washer are used for assembly. • The powder coating is done by Pure Polyester powder of Ackzonoble or Berger Paints with 60 to 70 micron thicknes Supply and fixing different type of steel pre-fabricated garden bench/ jhula/ slides and other children play items made of steel duly painted as per approved design and specifications by engineer in charge made of MS pipe, Flates, rectangular hollow section or other steel sections duly welded and or nut bolted where ever required, rubbing and buffing welded joints to make safe for use of child

Refer document

Refer document

INR 45 Lakhs /-