|
| 1 | B/R ITEMSDismantling old PGI/CGI sheeting any gauge, thickness including Nainital, Sikkim or similar pattern roof/facia including ridge etc and keeping serviceable sheets in safe custody for re-use complete all as specified and as directed. |
| 2 | Taking down chowkats with shutter of any description (without taking down shutter from the frame) exc 1.5 Sqm and n.exc 4.00 Sqm each and removing from site complete all as specified and as directed. |
| 3 | Taking down chowkats with shutter of any description (without taking down shutter from the frame) n.exc 1.5 Sqm each and removing from site complete all as specified and as directed. |
| 4 | Taking down shutters of any description 1 Sqm but n.exc 2 Sqm each and removal from site complete all as specified and as directed |
| 5 | Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), removing from the Sites and rubbish off the Premises, complete all as specified and as directed. |
| 6 | Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water remove Dust, debries/ rubbish etc., complete all as specified and as directed. |
| 7 | Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed. |
| 8 | M&L for surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and as directed. |
| 9 | Excavation in trenches n. exc 1.5 mtr wide and n. exc 1.5 mtr in depth for laying of cable and getting out in hard /dense soil complete all as directed. |
| 10 | Returning filling in soft/loose soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm complete all as specified and as directed |
| 11 | Removal of surplus excavated (soil) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and as directed. |
| 12 | M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed. |
| 13 | M&L for PCC 1:4:8 type C-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 14 | Demolition of precast concrete block walling built in cement mortar complete all as specified and as directed. |
| 15 | Demolition of stone or boulders masonry built in cement mortar including all quoins, arches, pillars, pre-cast PCC bond stones with separating serviceable stones & setting aside for reuse in the work complete all as specified and as directed. |
| 16 | Demolition of reinforced cement concrete of any description and in any position such as pre-cast drain cover or cover slab of drain etc (reinforcement cut as required to facilitate demolition) complete all as specified and as directed. |
| 17 | S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and as directed. |
| 18 | S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in ridges, valley, eaves etc fixed with self tapping screws complete all as specified and as directed. |
| 19 | S&F in repair3.0 mm thick tintedsheet glass panes, ordinary quality and glazing with oil putty including steel pin in square n.exc 0.5 Sqm in each pane fixed to steel frame complete all as specified and as directed. |
| 20 | M&L for 6mm thick plywood, grade BWR, type BB, fixed with nails to timber frame work in wall/ceiling complete all as specified and as directed. |
| 21 | M&L for hardcore of guage n.exc 0.63mm broken stone or boulders deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified & as directed. |
| 22 | S&F in repairs Harrison rail, mild steel, chromium plated, 25mm dia with fixing brackets, stops, rollers etc in curtain rails all specified and directed by Engr-in-Charge |
| 23 | Dismantling timber scantling 40 Sqcm and over in section any position as in unframd work including separating serviceable timber and keeping in safe custody for reuse complete all as specified and as directed. |
| 24 | M&L for 2nd class hard wood timber scantling fixed clean swan including trating with raw linseed oil as in unframed work complete all as specified and as directed. |
| 25 | S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed. |
| 26 | M&L for 35mm thick 2nd class HW plain, framed, paneled shutters (two panel) with lock rail and panel of 9mm thick BWR commerical ply or 12mm veneered particle board with commercial face veneering on both faces.The size of rail & site as per IS : 1003 (Part-I), Kiln, seasoned & chemically pressure, treated complete all as specified and as directed. |
| 27 | S&F of factory made solid PVC door frame of size 50mmx47mm made out of 5mm thick single side prelaminated PVC sheet reinforced with mild steel square tube and edges will be painted to match with single side prelaminated sheet as per specification and drawing) complete all as specified and as directed. |
| 28 | S&F of 30mm thick (style thickness) factory made solid panel PVC door shutter consisting of frame made out of mild steel tubes for top and bottom rails, solid steel frame shall be covered with heat moulded single side prelamPVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of both side prelam PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drawing complete all as specified and as directed. |
| 29 | S&F 100mm longbutt hinges, medium weight, cold rolled, mild steel complete all as specified. |
| 30 | S&F 75mm longbutt hinges, medium weight, cold rolled, mild steel complete all as specified. |
| 31 | S&F 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed |
| 32 | S&F 250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed |
| 33 | S&F for extruded aluminium alloy handles 150mm long, fabricated type, anodized complete all as specified and as directed. |
| 34 | S&F for extruded aluminium alloy handles 100mm long, fabricated type, anodized complete all as specified and as directed. |
| 35 | S&F for aluminium anodised barrel tower bolts, 150mm long of extruded section complete all as specified and as directed. |
| 36 | S&F for aluminium anodised barrel tower bolts, 100mm long of extruded section complete all as specified and as directed. |
| 37 | M&L for preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 38 | M&L for preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed. |
| 39 | Material & labor for non skid coloured ceramic tiles of 7 to 8mm thick ( Square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc conforming to IS-13712, grade B-II-(a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed/bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed. |
| 40 | Materials & labour for coloured glazed ceramic tiles of size (300x200mm/350x250mm/450x350mm) of 7mm thick, as in vertical surfaces such as skirting/dado/riser to steps etc conforming to IS-13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed/backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed. |
| 41 | M&L for pre-cast cement concrete block masonry with solid blocks, type C1 1:3:6 (20mm graded stone aggregate) exc 10cm in width and setting in mortar 1:6, complete all as specified and as directed. |
| 42 | M&L for brickwork with subclass \"\"B\"\" bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 43 | M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed. |
| 44 | M&L 10mm thick rendering plaster on fair faces of concrete faces in CM 1:4 on concrete/RR Masonary surfaces including the surfaces even and smooth with using extra cement complete all as specified and as directed. |
| 45 | M&L for rendering 20mm thick in cement mortar (1:4) in two layer of 10mm thick each with using WPC shall be mixed with cement mortar in finishing outer layer only as per manufacturer\"s instruction, on other than fair face of brick/stone masonry (external surfaces) finished surface fair and even without using extra cement complete all as specified and as directed. Note : (WPC shall be measured and paid separately as supply only) |
| 46 | M&L for preparation of old/new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer applied over 3mm thick super fine Birla or altek wall care putty finish including complete removal of existing treatment complete all as specified and as directed. |
| 47 | M&L for applying two coats of weather shield exterior emulsion paint over a coat of alkali resistant primer including preparation of new/old wall surface complete all as specfied and as directed. |
| 48 | M&L for applying two coats of white washing including preparation of new/old decorated surfaces of wall complete all as specified and as directed. |
| 49 | M&L for 25mm thick PCC 1:3:6 type C2(using 40mm graded stone aggreage) as in plinth protection/path/hardstanidng finished the concrete surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 50 | M&L for 75mm thick PCC (1:3:6), type C-2 (using 40mm graded stone aggregate) as in plinth protection, path/hardstanding etc laid in bays/panels n.exc 2.00 Sqm each including construction joints at suitable interval and each corner and filled with bituminous mastic filling (1 Part bitumen & 3 part sand) and finished the surface even and smooth without using extra cement complete all as specified and as directed. |
| 51 | M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in surface channels and drains including forming fair finished to drain channel complete all as specified and as directed. |
| 52 | S&F in repairs 75mm bore, PVC(SWR) pipes of pressure rating 4 kgf/cm2, single socketed in any length with rubber ring joints, laid in trenches or in floors or as in weep hole with necessary clamps, bolt, bends, Tee etc complete all as specified and as directed. |
| 53 | M&L for stone walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6) including brought up to courses complete all as specified and as directed. |
| 54 | M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in coping including necessary formwork complete all as specified and as directed. |
| 55 | M&L for mild steel TMT bars, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally, hooping for columns, hookings ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 56 | M&L for labour for Mild steel TMT bars 5mm dia and over upto including 10mm dia as in stirrups, spacers and binders cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 57 | M&L for labourfor RCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in manholes covers etc including necessary form work complete all as specified and as directed.Note : Re-inforcement shall be measured and paid separately. |
| 58 | M&L for hand packing using broken stone or boulders (any thickness) at back or block masonry retaining wall and raising or lowering to the required level complete all as specified and as directed. |
| 59 | M&L for struck or recessed pointing in cement mortar 1:4 to brick or stone wall complete all as specified and as directed. |
| 60 | M&L for lacquer coated coloured chequered cement concrete tiles of size 300x300x25mm thick set, jointed and pointed in neat slurry in floors and steps with grey cement and pigments over and incl 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and as directed. |
| 61 | M&L for 100mm thick PCC (1:3:6), type C2 (using 40mm graded stone aggregate) as in path/steps etc finished even and fair without using extra cement incluidng necessary formwork complete all as specified and as directed. |
| 62 | M&L for 100mm thick PCC (1:2:4), type B2 (using 40mm graded stone aggregate) as in hardstanding/flooring etc finished even and fair without using extra cement including necessary formwork complete all as specified and as directed. |
| 63 | M&L for 150mm thick cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in path/steps/drain bed finished cement concrete surfaces fair and even including forming construction joint filled in CM (1:4) complete all as specified and as directed. |
| 64 | M&L for forming 12mm wide and 100mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed compound Grade \"B\" complete all as specified and as directed. |
| 65 | M&L for 30mm thick 2nd class hard wood well seasoned glazed and skeleton shutters, open rebated and prepared to receive glass gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and as directed. |
| 66 | Supply only Liquid Water Proofing Compound, as approved, complete all as specified and as directed. |
| 67 | S&F in repairs 110mm bore PVC (SWR)pipes single sockets, in any length with rubber ring joints, laid in trenches or in floor with necessary clamps, bolts, bends, Teebend of any radius for PVC(SWR) pipes/steel gutters etc fixed to walls complete all as specified and as directed. |
| 68 | Supply and fix in repairs 110mm bore PVC(SWR) bend of any radius for PVC (SWR) pipes/steel gutters etc, fixed to walls complete all as specified and as directed. |
| 69 | Excavation in post holes (or similar holes) in soft/loose soil each n.exc 0.5 Cum, getting out, returning, filling in an ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm and removing surplus soil to a distance n.exc 50 mtrs complete all as specified and as directed by the Engr-in-Charge. |
| 70 | S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafter and running rails and guides for sliding doors fixed with angle clear or other connecting plates conforing to Fe-410-W(Gde-E-250 quality-A)including one coat of red oxide zinc chrome primer after preparation of surfaces at contractor\"\"s workshop before fabrication complete all as specified and as directed. |
| 71 | E/M ItemsTaking down carefully point wiring of any type (i.e. on wooden batten, surface conduit, casing-N- capping or concealed conduit) complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, conduit etc. including accessories such as wooden gutties/rawal plug, screw etc including making good disturbed surface to match the existing surface all as specified & directed. |
| 72 | Taking down carefully by unscrewing from boards/outlet boxes, DBs, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling, fittings, bulk head fittings, tubelight fitting etc. Complete all as specified and as directed. |
| 73 | Taking down MCB of any type or rating and keeping aside complete all as specified and as directed. |
| 74 | M & L for point wiring with 1.5 Sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) Cable of working voltage 1100 Volts grade conforming to IS-694 pt-I & II of 2000 drawn in and including 25 mm size PVC rigid non matellic casing caping (Double lock)with all casing capping fittings &accessories with 1.60 mm thick pressed steel or mild steel sheet sunk box covered with 3 mm thick backelite sheet fixed with brass screws & cup washers including 1.5 sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) cable as earth continuity conductor connected to main switch / DB\"s or common earth dolly complete forfor light point/ fan point/ exhaust fan point/ call bell point/ controlled by one switch 5/6 Amp one way complete all as specified and directed. |
| 75 | All as per item No. 74 above but switch socket combination 3 Pin 5 Amps on same board |
| 76 | All as per item No. 74 above but switch socket combination 3 Pin 5 Amps on same board |
| 77 | All as per item No 74 here-in-before but for one socket outlet of 15 Amps fixed on independent board with 2.5 Sq mm multistranded copper conductor wire FRLS PVC insulated and 2.5 Sq mm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge |
| 78 | S&F in repairs switch piano flush button,single pole, two way, 6 amps complete all as specified and as directed.Make : Anchor Product Code No 50064 or equivalent of approved make |
| 79 | S&F in repairs switch socket combination modular type, 2 in 1, 6 pin, 5/6 Amps and 15/16 Amps, multipurpose , flush, non shutter, non inter locking type, 230 volt flushtype, white/ivory finish with two fixing hole including suitable gang box completecomplete all as directed including taking down old one. Make : Crabtree, Legrand and L&T or equivalent of approved make |
| 80 | S&F in repairs switch socket combination, 2 in 1, 6 pin, 5/6 Amps and 15/16 Amps, multipurpose , flush, non shutter, non inter locking type, 230 volt flushtype, white/ivory finish with two fixing hole including suitable gang box completecomplete all as directed including taking down old one. Make : Anchor Cat No 38808/50665 or equivalent of approved make |
| 81 | S&F in repairsceiling rose, PVC/polycarbonate insulated body, 3 terminal and 240 volts, ISI markedcomplete all as specified and directedMake : Anchor Product Code No 39040 or equivalent of approved make |
| 82 | S&F in repairs lamp holder angular/straight insulated body, with back plate suitable for batten fittings, white/ivory finish complete all as directed.Make : Anchor Product Code No 39527 or equivalent of approved make |
| 83 | S&Fdecorative LEDtube light fitting 1x18 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 84 | Supply and fix in repairsintegrated LED bulk head fittings of 10 watts, presure die cast housing acrylic diffuser and frame with IP 66 protection complete all as specified and as directed Make :Havells Cat Part No.HEXAFT10WLED857SSYMBOPC or equivalent of approved make) |
| 85 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50Hz,RPM1200, Copper winding of sweep 250mm complete all as specified and as directed. |
| 86 | M&L for submain wiring alongwith earth wire of size 2x6.0 Sqmm + 1x6 Sqmm earth wire ISI marked FRLS PVC insulated multi stranded copper conductor single core cable drawn in and incl PVC casing and caping of adequate size with all accessories as required as specified and as directed incl taking down old unserviceable submain wiring. (Note : Three runs of PVC wire with one run of PVC casing and caping will be measured and paid as one length.) |
| 87 | S&F in repairs sheet metal enclosure DB\"s 240 Volts, IP-43, suitable for mounting MCB\"s, SPN,8 way with 200 Amps rated copper bus bar double door type complete and including taking down old DBwith MCB complete all as specified and as directed.vells/ABB/Legrand)(Make : L&T cat No DBSPN008DD or equivalent of approved make) |
| 88 | S&F in repairs MCB single pole & neutral 40 to 63 Amps, 240 Volts, 10 KA rapturing capacity,\"C\" Curve complete all as directed by Engineer-in-charge.(Make : L&T cat No BB20400C to BB20630C or equivalent of approved make) |
| 89 | S&F in repairs MCB single pole 6 to 32 Amps, 240 Volts, 10 KA rapturing capacity, \"C\" Curve complete all as directed by Engineer-in-charge. (Make : L&T cat No BB10060C to BB10320C or equivalent of approved make) |
| 90 | Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected with galvanised iron/steel earth wire of 4mm dia by means of bolts, nuts, check nuts and washers made outof galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part-I and earth wire protected by galvanized pipe light grade 15mm bore and connected to VTPN DB/SPN DB including neccessary earthwork and excavation in any type of soil, GI light grade 20mm bore watering pipe with funnel and wire mesh, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2;4 type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS hook 6mm dia MS bars etc complete all as specified and as directed including testing on completion. |
| 91 | S&F electrical water heater storage with copper inner tank and heating element, capacity 25 Ltr BEE-5 Star rated complete with all accessories such as safety valve thermostate, NRV, connection piece etc.Make : Havells, Cat -Monza DX GHWBMGSWH0550 or equivalent approved. |
| 92 | Supply, laying, jointing & testing 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured LT electric power cables, heavy duty with aluminium conductor of cross sectional area 25 Sqmm 2 core with all fixing & connecting accessories as in service connection complete all as specified and as directed including taking down old unserviceable one. Note : The rate quoted by the bidder shall be deemed to be inclusive of cost of aluminium thimbels/lugs of suitable size. |
| 93 | Supply & fixing Rotational moulded polyethylene water storage tank, 1000 litres capacity, ISI marked multi layer constriction (cylindrical vertical with closed top), hoisted & fixedin position including supply and fixing of25mm bore Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe of having weight not less than 455 gms including connection complete all as specified and as directed including dismantling of old unserviceable water tank.Make of Water Tank : SINTEX or equivalent make approved.Make of Ball Valve : Prayag or equivalent make approved. |
| 94 | Supply and laying steel water tubing, medium grade, galvanised with all running fitting fitting fixed on wall/floor/ceiling complete of size 25mm bore complete all as specified and as directed. |
| 95 | Screwing 25mm bore in existing steel tubing for alteration or addtions (or lengthening screw on pipe to forming connections) complete all as specified and as directed. |
| 96 | S&F in repairs 15mm bore Brass CP mixer for mixing holt & cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make : ESSCO Cat Part No. SQT 516KN or equivalent approved make. |
| 97 | S & F 15mm bore gun metal gate valves , ISI marked with iron wheel head ,screwed both ends for iron pipe and fixed complete all as directed and specified |
| 98 | S & F 25mm bore gun metal gate valves , ISI marked with iron wheel head ,screwed both ends for iron pipe and fixed complete all as directed and specified |
| 99 | Supply and laying steel water tubing, medium grade, galvanised with all running fitting fitting fixed on wall/floor/ceiling complete of size 15mm bore complete all as specified and as directed. |
| 100 | S&F stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 15mm bore, complete all as specified and as directed. |
| 101 | Supply & fix stop connection 15mm size with PTMT nuts of length 750 mm complete all as specified and as directed. |
