Urban Development Department-UDD has published Renovation Work Of Jhiri Office Building Renovation Work Of Jhiri Office Building. Submission Date for this Tender is 16-11-2021. Building Repair Tenders in AS PER NIT Jharkhand. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Labour for cleaning the work site before and after work etc. |
| 2 | Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l. |
| 3 | Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item B) 60% of total excavation |
| 4 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including" cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume). |
| 5 | Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l. |
| 6 | Providing and laying in position cement concrete of specfied grade excluding the cost of centering and shuttering-All work up to plinth level. 1:2:4(1Cement:2coarse sand(Zone-III): 4 graded stone aggregate 20mm nominal size) |
| 7 | Providing designation 75 A brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 8 | Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l. |
| 9 | Providing tor steel reinforcement of 8mm.,10mm dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. Taking 8mm TMT FE 500 ( only valid forTata (Tiscon) SAIL, JSPL, Electro Steels Ltd., Bokaro, & Vizag (RINL) 10mm dia |
| 10 | 8mm dia |
| 11 | Supplying, fitting and fixing 35mm thick solid core typedecorative single leaf flush door shutter with both sides decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 12 | Providing & fixing pressed steel door frames manufacturedfromcommercialmild steelsheet of 1.25mm thickness including hinges ,jamb,lockjamb,beadand if requiredangle threshold of mild steel angle section 50 X 25mm, orangle threshold of mild steel angle section 50 X 25mm, orbase ties of1.25mm pressedmild steel welded or rigidlyfixed together by mechanical means, adjustable lugs withsplitendtailto eachjambincludingsteelbutt hinges splitendtailto eachjambincludingsteelbutt hinges 2.5mmthickwithmortarguards,lockstrike-plate and 2.5mmthickwithmortarguards,lockstrike-plate andshockabsorbersasspecifiedandapplyinga coatof approvedsteelprimerafterpre-treatment of the surface as directed by the Engineer Incharge - Profile - B- Fixing with adjustable lugs with split end tail to each jamb |
| 13 | 30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm . 19mm for styles and 15x15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on eigher side forming styles: and 5 mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mmshall be tapered in 45 degree on the inner side to form top and bottom raiil and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided eigher side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded / sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the "C" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer"s specificatio n& drawing (for W.C. and bathroom door shutter). |
| 14 | providing and fixing ISI markedaluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) tramsparent or dyed to required colour or shade with necessary screws etc. complete 125X75X4mm |
| 15 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete Twin rubber stopper |
| 16 | Providing and fixing luminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transpoarent or dyed to required colour or shade with necessary screws etc. complete 150X10mm |
| 17 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or deyed to required colour or shade with nuts and screws etc. complete. 250X16mm |
| 18 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriateZ sections and other sections of approved make conforming to IS : 733 and IS: 1285 fixing with dash fasterners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required DPDM rubber/neoprene gasket etc.,aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling C.P. brass/stainless steel screws, all complete as per architetural drawings and the directions of Engineer-in-charge (Glazing, panelling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required inlcluding the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) --- Polyester Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 19 | Providing and fixing glazing in aluminium door, windows, ventilators, shutters and partitions etc, with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4mm thickness |
| 20 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.) Window grill |
| 21 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l. |
| 22 | Providing and fixing stainless steel (grade 304) railing made of Hollow tubes, channels, plates etc,. Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessry stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasterners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasterners etc,.) |
| 23 | Providing and laying 15 to 23mm thick Kotah stone tiles in risers of steps, skirting and pillars of approved size, taxture and colour and over 12mm thick cement mortar (1:3) and joined with grey cement slury mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, txes and royalty all complete as per building specifiction and direction of E/I. |
| 24 | providing and laying Double charge vitrified floor tiles in different sizes thickness to be specified by the manufactured ) with water absorption less than .08% and conforming toIS 15622/ISO 13006 of approved make in all colours and shade laid on 20mm thick cement mortar (1:40 jointing with grey cement slurry @3.3kg/sqm including grouting the joints with white cement and matching pigment etc. size of tile 600x600 |
| 25 | Providing and laying rectified glazed ceramic floor tiles 300x300m or more (thickness to be specified by manufacture) of 1st quality conforming to IS:15622 with approved make in colours white, ivory, grey, fume red, brown laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments, etc all complete. |
| 26 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l. a With "A" grade white 15 x 15 cm tiles. |
| 27 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curingwithall leadsand liftsof water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 28 | Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l. |
| 29 | Providing two coat of snocem of approved shade and make over a coat of cement primer on new surface including prepared the plaster surface to prepare the surface even and smooth complete. |
| 30 | Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt, scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specifcation and direction of E/I. |
| 31 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l. |
| 32 | Providing & fixing on wall face unplasticised -Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia |
| 33 | Providing & fixing on wall face unplasticised -Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 75 mm dia |
| 34 | Providing and fixingon wall face unplaqsticised- PVCmoulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,includingjointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. Bend 87.5 degree 75mmbend |
| 35 | 110mm bend |
| 36 | Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete -110mm |
| 37 | Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete -75mm |
| 38 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 39 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes |
| 40 | 15 mm nominal outer dia Pipes |
| 41 | 20 mm nominal outer dia Pipes |
| 42 | 25 mm nominal outer dia Pipes |
| 43 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.2 White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 44 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS: 8931. 18.52.1 15 mm nominal bore |
| 45 | 18.64 Providing and fixing PTMT swiveling shower, 15 mm nominal bore, weighing not less than 40 gms |
| 46 | 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 47 | Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931. 18.52.1 15 mm nominal bore |
| 48 | Providing and fixing stainless steel A ISI 304 (18/80) kitchen sink as per IS:13983 with brackets stainless steel plug 40mm ,including painting of fittings and brackets ,cutting and making good the walls wherever required. Kitchen sink with drain board 510x1040mm bowl depth 250mm |
| 49 | Providing and placing on terrace (at all floor levels)Polythene water storage tank of IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and thebase support for tank. (e.g. Sintex etc.) |
| 50 | construction masonry chamber 60x45x50 cm inside in brickwork in cement mortar 1:4(1 cement :4 coarse sand ) for water meter complete with c.i. double flap surface box 400x200-x200mm (inside) with locking arrangement and RCC top slab 1:2:4mix (1 cement:2 coarse sand :4 graded stone aggregate 20mmnominal size )necessary excavation ,foundation concrete 1:5:10 and inside plasteringwitth cement mortar 1:3 12mm thick finished with |
| 51 | S/F piano type switch / socket : supplying and fixing following piano type swith / socket on the existing switch box /cover including connections etc required. 5/6 amps switch JSR 1.23.1 |
| 52 | 3 pin 5/6 amp socket outlet JSR 1.23.4 |
| 53 | 6pin 15/16 amps s.s combind JSR 1.23.6 |
| 54 | Supplving and drawing following sizes of FR PVC insulated copper conductor,2 single core cable in the existing surface/recessed steel/PVC conduit as required. J.S.R 1.22 1X 1.5 Sq mm JSR 1.15.1 |
| 55 | 2x 2.5 sq.mm JSR 1.15.11 |
| 56 | 2x 6 Sq. mm 15R 1.15.29 |
| 57 | Supplying and fixing PVC/G.I. box of following size on surface or in recess with suitable size of phenolic as required. JSR 1.22 laminated sheet cover in front including, painting etc. as required JSR 1.22 75 mm x 75 mmx 50 mm deep/(4" x 4") JSR 1.22.1 |
| 58 | 72 mm x 146 mm x 48 mm deep/(4"x7") JSR 1.22.2 |
| 59 | 121 mm X 173 mm x 48 mm deep.(8" x 10") JSR 1.22.6 |
| 60 | S/F brass holder: Supplying and fixing brass battern/angle holder including etc required (of make anhor/Miner/Arkaylite): JSR1.34 |
| 61 | Celling rose, 2 pin, S amps ISI marked, JSR 1.33 |
| 62 | Ceiling fan 48"(1200 mm) JSR 2101 |
| 63 | 9/10 Watt led Bulb JSR 2231 |
| 64 | 1X14 watt TS tubelight fitting JSR 2261 |
| 65 | Supplying and fixing stepped type electronic fan regulator on the existing 10 modular plate switch box including connections but excluding modular plate etc. as required.JSR 1.25 |
| 66 | Supplying and fixing following, 240 Volts "C" series MCB in the exixting MCB DB complete with connection, testing and commissioning etc as required 6/32 amps SP JSR 2.12.1 |
| 67 | 63 amps,TPN ISR 2 11.10 |
| 68 | S/F HRC fuse type TP&N switch disconnector: Providing and fixing following capacity double pole/TP&N Sheet metal switch. disconnector fuse unit in existing metal board, with ISI marked HRC fuse, including drilling hole in metal board, making connection etc. as required. JSR 2.1. 100 amps TPN JSR 2.1.6 |
| 69 | S/F Busbar chamber Providing and fixing following capacity busbar chamber with 4 strips of 13 suitable size made of copper, heavy duty, complete with all accessories including connections, earthing the body, etc as required. 100 amps J.S.R 25.1 |
| 70 | LED FLOOD Light 50/60 W JSR 2222 |
| 71 | S/F PVC conduit: supply and fixing of following sizes PVC conduit along with 15 accessories in surface /recess including cutting the wall and making good the samsa in case recessed conduit as required. 15R 1.21 25 mm JSR 1.21.2 |
| 72 | Laying of Cable MV cable laying upto 25 sqmm in ground- laying of one number PVC insulated power cable 1.1 kv grade of size not exciding 35 sq mm direct on ground including excavation, sand cashioning protection covering and refilling the trench etc as required. |
| 73 | Earthing with copper plate electrode earth pipe 600mm x 600 mm x 3 mm including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/coke and salt) as required. JSR 3.6 |
| 74 | Salt/charcoal for pipe earth electrode Extra for using salt and charcoal for pipe earth electrode as required JSR 3.3 |
| 75 | S/L 25mmX5mm G.I earth strip in ground: Supplying and laying 25mmX5mm G.I strip at 0.50 Mts below ground as stripe earth electrode, including soldering etc as required JSR3.12 |
| 76 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way, Double door JSR 2.8.8 |
| 77 | S/F sheet metal ON/OFF-Load changeover : Providing and fixing following capacity 2 pole/4 pole ON/OFF load changeover switches with side handle operation, in sheet encloser in existing metal board including drilling hole in metal board, making connection earthing the body etc. as required. JSR 2.6 100 amps, 4 pole JSR 2.6.5 |
| 78 | 25 Sqmm, 3.5 Core PVC/XLPE indutated PVC sheathed, Heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 Volts. J.S.R 1906 |
| 79 | Supplying of 100mm dia 01.50 H.P. (ISI Mark) KSB/Kirlosker/CRI/V-guard Submersible Motor Pump sets comfirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50Hz, A.C. supply with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non returned valve shall be provided with pump. 3 meter submersible copper in single/double run shall be provided with each |
| 80 | Supplying 1.5 sqr. mm. Cable ISI Marked for above requirement. |
| 81 | Supplying of 32mm Submersible Pipe of standard make Ashirwad/Raksha/Prince/Gupta or any equivalent make for above requirement. |
| 82 | Supplying of 02 Nos. clamp, Band, Adopter, Bore Cover, Rope etc. as required for above work. |
| 83 | Installation charges with Plumbers & equipments for Installation of Motor Pump over bores and its commisioining. |
| 84 | Providing of Electric Connection Charges, for Commissioning of above. |
| 85 | Supplying, fitting, fixing & laying of PVC Pipe for Connetion in-let and out-let etc. all complete as per specification and direction of E/I. 25mm dia PVC pipe |
| 86 | 32mm dia PVC pipe |
| 87 | Supplying & fixing UPVC Fitting of approved make all complete 3.1.13 as per specification and direction of E/I. 25mm dia Elbow |
| 88 | 32mm dia Elbow |
| 89 | 32mm dia Plain Tee: |
| 90 | 25mm dia Plain Tee |
| 91 | 32mm dia Union socket |
| 92 | 25mm dia Union Socket |
| 93 | 25mm dia Socket |
| 94 | 32mm dia Socket |
| 95 | 15mm Tap (Plastic Tap) |
| 96 | Supplying & Fitting Panel Board (BCH etc.), Standared make with all accessories as per E/I. |
| 97 | Construction of Brick masonary chamber with RCC Slab as per E/I. (Annexure-X) |
| 98 | Bricks- 7KM + 1 km. |
| 99 | L.sand14km |
| 100 | Sand- 49km |
| 101 | Chips - 22km |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
