|
| 1 | Excavation in trenches in any type of soil and not exc 1.5 m wide and n.exc 1.5 m in depth for laying of cable and fixing poles, stays etc and getting out complete all as specified and directed |
| 2 | Returning , filling in including spreading leveling, watering and well ramming in layers not exceeding 25 cm thick with excavated soil complete all as specified and directed. |
| 3 | Removing excavated material (surplus soil) to a distance not exceeding 50 mtrs and depositing where directed at a level not exc 1.5 m above the starting point all as specified and directed. |
| 4 | M&L for sand cushioning to PVC cable with using clean dry and natural river sand and gently punning down below/around cable complete all as specified and directed. Note : Punned thickness shall be measured for payment. |
| 5 | Supply, laying and fixing galvanised iron pipe light grade, laid under roads/ drain / along with the pole /fixing of airtermination rodwith flat iron clamps, bolts, nuts washers complete all as specified and directed of following size:- |
| 6 | Size of 40 mm bore dia. |
| 7 | Size of 50 mm bore dia. |
| 8 | Supply and fix cable cover, class LV, flat, size 190mm x 90mm x 90mm as in protection of cable laid dry, flat, abutting each other width wise complete all as specified and directed. |
| 9 | Supply, laying, jointing and testing of LT underground, XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, Heavy duty, electric power cable laid in trenches/ ducts/fixed on pole/ wall / laid under road / path / culvert / drains / culverts encased in GI pipe, electric cable with aluminium stranded conductor, including jointing and testing 1100 volts grade with necessary lugs and compression brass glands including taking down old cable complete all asspecified and directed. |
| 10 | 120 Sq mm 3.5 core |
| 11 | 95 Sqmm 3.5 core |
| 12 | 70 sqmm 3.5 core |
| 13 | 50 sqmm 3.5 core |
| 14 | 25 Sq mm 4 Core |
| 15 | 16 sqmm 4 core |
| 16 | 10 sqmm 2 core |
| 17 | M&L for straight through joint outdoor type for LT UG cable including jointing kits heat srinkable typecomplete suitable for aluminium conductor cables complete all as specified and directed of the following size. |
| 18 | Size of 25 to 50 sqmm3.5 core |
| 19 | Size of 70 to 95 sqmm3.5 core |
| 20 | Size of 120 to 185 sqmm3.5 core |
| 21 | M&L forfixingMCCB 4 Pole 63 AmpsConforms to IS/IEC 60947-2,IEC 60947-2 & EN 60947-2,Ics=100% of Icu,Common SS Enclosure with Thermal Magnetic Release, 415 volts, 10 KA complete all as specified and directed. |
| 22 | M&L forfixingMCCB 4 Pole 100 AmpsConforms to IS/IEC IS/IEC 60947- & IEC 60947-2,Ics=100% of Icu,Common SS Enclosure with Thermal Magnetic Release, 415 volts, 25 KA complete all as specified and directed. |
| 23 | M&L forfixingMCCB 4 Pole 160 AmpsConforms to IS/IEC IS/IEC 60947- & IEC 60947-2,Ics=100% of Icu,Common SS Enclosure with Thermal Magnetic Release, 415 volts, 25 KA complete all as specified and directed. |
| 24 | M&L forfixingMCCB 4 Pole 200 AmpsConforms to IS/IEC IS/IEC 60947- & IEC 60947-2,Ics=100% of Icu,Common SS Enclosure with Thermal Magnetic Release, 415 volts, 25 KA complete all as specified and directed. |
| 25 | M&L forfixingMCCB 4 Pole 250 AmpsConforms to IS/IEC IS/IEC 60947- & IEC 60947-2,Ics=100% of Icu,Common SS Enclosure with Thermal Magnetic Release, 415 volts, 25 KA complete all as specified and directed. |
| 26 | M&L forfixingMCCB 4 Pole 400 AmpsConforms to IS/IEC IS/IEC 60947- & IEC 60947-2,Ics=100% of Icu,Common SS Enclosure with Thermal Magnetic Release, 415 volts, 50 KA complete all as specified and directed. |
| 27 | Supply and fixAluminium cable lugs ( lugs are made from 99.5% pure aluminium) as per IS of following Size;- |
| 28 | 185 Sq mm |
| 29 | 120 Sq mm |
| 30 | 95 Sqmm |
| 31 | 70 sqmm |
| 32 | 50 sqmm |
| 33 | 35 sqmm |
| 34 | 25 Sq mm |
| 35 | Supply and fix MCB, single pole and neutral link240 volts 40 to 63 Amps capacityC series fixed inLT panel including taking down old unserviceable MCBs.complete all as specified and directed. |
| 36 | Supply and fixVoltmeter digital type accuracy Class 1.0, 0.5, Input voltage measurement range 50-520 VAC (P-P), Aux supply 80-300 VAC,CT secondary site selectable 1A / 5A,Flush mounting 96 x 96 mm, Inbuilt selector switch for 3 phase meters.complete all as specified and directed. |
| 37 | Supply and fixAmmeter digital type accuracy Class 1.0, 0.5, 1A / 5A,Flush mounting 96 x 96 mm, Inbuilt selector switch for 3 phase meters.complete all as specified and directed. |
| 38 | Supply and fix AVF meter(amper,Volt and Frequency meter ) digital type accuracy Class 1.0, ,Flush mounting 96 x 96 mm, Inbuilt selector switch for 3 phase meters.complete all as specified and directed. |
| 39 | Supply and fixSelector switch for voltmeter/ ammeter .complete all as specified and directed. |
| 40 | Supply and fixSPhase indicator lamp neon type complete with holder assy RYB complete all as specified and directed. |
| 41 | Supply and fixCT coils of range .200/5 Amp complete all as specified and directed. |
| 42 | Servicing and repair to APFC Panel 75 to 125kvar Capacity Complete wiring with Suitablecopper wire ISI marked withindicating Lamp, Ampere Meter, voltmeter and required items for working Conditioncomplete all as specified and directed.Note :- Spares should measures and Paid Separetely |
| 43 | Capacitor cylinderical type 5 to 25KVAR capacity complete all as specified and directed. |
| 44 | Capacitor 20 to 25KVAR capacity.complete all as specified and directed. |
| 45 | M&L in replacement for on load changeover switch of capacity 200 amps 4 pole including removing old changeover switch any type and necessary fixing on wall/in LT panel complete all as specified and directed.complete all as specified and directed. |
| 46 | Servicing / repair including preventive check and operatioal checkof 2 ton EOT crane fordismantling of hoisting gear box, drain of old oil, cleaning of gear box, fill up fresh oil in gear box. Long travel, cross travel gear box oil check up and fillingoil. Checking of hoisting, long travel, cross travel, break unit, shifting of berak unit, oiling of break unit pins. Greasing in long travel cross travel wheel bearing, Checking of panel board and connections, Overhauling of PPB, Greasing on Wire rope Drum , checking of push button connections checking of power festooning cable checking of long travelo rail alignment, checking of cross travel rail alignment Bottom block assembly(hook assembly) cleaning, checking and oiling Greasing of wire rope, rope drum, pedestal bearings including load test using dead weight,duly sign by user and sumbit to AGE E/M office timely complete all as specified and directed. |
| 47 | Note :-(i) Contractor will provided necessory oil, grease, cloth waste and Minor Spares Required will Be Deemed to be included in Quoted rate.(ii) Load Test will be carried out after Completion of the Entire work and a Certificate duly Signed by the user will be Submitted by the Contractor.(iii) The Contractor will give one Year Gurantee from the Date of Completion of Work in writing.(iv) Spares should be measured and paid separetely.(v) Operational check carried out by competent person of authorised firm only. |
| 48 | Supply and fixing the following spares in replacement/ fixing at site for EOT/ HOT crane complete all as specified and directed. |
| 49 | Long travel limit switch |
| 50 | Crosstravel limit switch |
| 51 | Brake unit for hoising |
| 52 | Single phase Preventor |
| 53 | brake Set |
| 54 | Gear oil |
| 55 | Push Button |
| 56 | Servicing / repair including preventive check and operatioal checkof1.5 to 2 ton HOT crane for oiling and Greasing of long travelo rail alignment, checking of cross travel rail alignment Bottom block assembly(hook assembly) cleaning, checking and oiling Greasing of wire rope, rope drum, pedestal bearings complete all as specified and directed.NOTE :- including load test using dead weight,duly sign by user and sumbit to AGE E/M office timely complete all as specified and directed. |
| 57 | Note:-(i) Contractor will provided necessory oil, grease, cloth waste and Minor Spares Required will Be Deemed to be included in Quoted rate.(ii) The Contractor will give one Year Gurantee from the Date of Completion of Work in writing.(iii) Spares should be measured and paid separetely. |
| 58 | Material and labour only for watering (by means of water tanker) the existing earthing pit at makarpura airforce station and measuring of earthing in ohms and writing the result at near place by applying black paint at base writing the result in yellow with date of measurement and next due date near each panel and transformer/any other place by disconnecting the earthing strip from terminal/junction and reconnection after measurement of result and mainting the resister duly signed by user,contractor complete all as specified and directed.NOTE :- (i) contractor shall quote the rates by including the charges of making arrangement of watering the earthing pits at any site and location inside Airforce makarpura area.(ii) Also, contractor shall bring his own measuring instruments whatever is required to carry out the job. (iii) cleaning or replacing the exisiting sticker and writing the new as on date data on exisiting test result board on site shall be inclusive of the quoted rates. (iv) Contractor shall take before permission for watering earth pitto user intimation for detailment ofreprasentive. Obtainuser signature is responsibility of contractor. |
| 59 | M& L for making proper connection of loose/hanging lighting arrester aluminium /Copper / G I strip strip on existing position with porcelain saddles ,brass screw including drilling and fixing with entire satisfaction to engineer in charge . Note . Rate included in any height of Bldg (Roof /Wall etc) after completion signature obtained by the User is the responcibility of Contractor. Note :Contractornot completed the work before completion a recovery of 2 times of quoted rate shall levied. |
| 60 | S&F in repairs Air termination single pointed, Aluminium rod 12mm dia and 300mm long complete all as specified and directed. |
| 61 | S&F in repairs Test point terminal block made of MS powder coated MS Sheet of 1.6mm thick sheet of size 230X230X 75mm drilled and screwed including terminals for two strips entry and exit with overlapping for testing earth result complete all as specified and directed. |
| 62 | Labour only for servicing of DG set including replacement of fuel filters,oil filters,air filter element,changing oil,cleaning fuel lines,checking leakage and repairing it,replacement of exhaust main fold gasket etc all as specified and directedas per manufacturer/authorised service centre for the following:-Note. .Rate quoted shall be included i) Checking of Battery specific gravity every month and the acid level once in Three monthand top with distilled water if required. (Applicable for lead acid Battery only). Outputvoltage check and condition check to be carried out in SMF type batteryii) Checking charging alternator output voltage with respect to specificationsiii)To check the condition of Diodes/ rotating rectifier etc.iv)Checking of all electrical connections for their proper tightness including chargingalternators and battery clamps.v)Engine Panel / PCC, Alternator will be covered in AMC.vi)Replacement of all filters, refilling of engine oils, checking of all nuts and bolts tightness,correction of engine alternator alignment in case defect and replacement of rubber insert/block if broken to be carried outvii)Service engineer shall carry out \"B\" checks on the engine, as per the check listand would correct / recommend / suggest improvement in operation and performance. |
| 63 | 12.5/15 KVA |
| 64 | 20 KVA |
| 65 | 25 KVA |
| 66 | 30 KVA |
| 67 | 50 KVA |
| 68 | 82.5KVA |
| 69 | 125 KVA |
| 70 | 320 /380 KVA |
| 71 | Attending any fault ( Start /Stop) or other defects on emergency basis of technecian for the entire period of contract on DG set of any Capacity and AMF Panel or other control panel all as directed Service engineers to visit the site once in a month totaling to Ten visits per year. The schedule of visits can be mutually decided,if in normal condition by Engineer in Charge. |
| 72 | Supply and fixing the following spares in replacement/ fixing at site for DG sets/ AMF panels complete all as specified and directed. |
| 73 | Air Filter Primary for Generator 25 KVA - 62.5 KVA |
| 74 | Lube Oil filter for Generator 25 KVA - 62.5 KVA |
| 75 | Fuel Filter filter for Generator 25 KVA - 62.5 KVA |
| 76 | Air Filter Primary 75 KVA - 82.5 KVA |
| 77 | Air Filter Safety Inner75 KVA - 82.5 KVA |
| 78 | Fuel Water Separator 75 KVA - 82.5 KVA |
| 79 | Oil Filter 75 KVA - 82.5 KVA |
| 80 | Fuel Filter 75 KVA - 82.5 KVA |
| 81 | Air Filter Primary 100 KVA – 125 KVA |
| 82 | Air Filter Safety Inner100 KVA – 125 KVA |
| 83 | Fuel Water Separator 100 KVA – 125 KVA |
| 84 | Oil Filter 100 KVA – 125 KVA |
| 85 | Fuel Filter 100 KVA – 125 KVA |
| 86 | Air Filter Primary225 - 320 KVA |
| 87 | Air Filter Safety Inner225 - 320 KVA |
| 88 | Fuel Water Separator 225 - 320 KVA |
| 89 | Oil Filter225 - 320 KVA |
| 90 | Fuel Filter 225 - 320 KVA |
| 91 | Super By Pass Filter320 KVA |
| 92 | ½ Ltr Lube Oil Filter320 KVA |
| 93 | Fuel pipe wire braded 1,1/4\"\" to 3/8\"\" PVC best quality as per existing make( FEED PUMP TO FUEL FILTER ) |
| 94 | Oil pressure gauge complete. |
| 95 | Oil pressure Switch complete. |
| 96 | Water temperature gauge |
| 97 | Ignition switch |
| 98 | Indicating lamp |
| 99 | Battery terminal heavy duty of brass. |
| 100 | Distilled water. |
| 101 | coolant for radiator. Sealed bottle |
| 102 | Engine oil premium blue 20W 40 |
| 103 | Fan belt. Make Fenner/Dunlock |
| 104 | Self starter 12 volts |
| 105 | Self starter 24 volts |
| 106 | Gasket Set |
| 107 | Turbo charger assembly up to 50 KVA Dg set |
| 108 | Fuel Injector pumpup to 30 KVA |
| 109 | AVR 82.5 KVA |
| 110 | AVR up to 50KVA |
| 111 | Battery lead 1.5 meter long 16 sq mm copper conductor |
| 112 | Solenoid Valve |
| 113 | Engine Couplingfor DG set 30 KVA to 82.5 KVA |
| 114 | Battary 12 Volt 100 AH |
| 115 | Battary 12 Volt 150 AH |
| 116 | Battary 12 Volt 180 AH |
| 117 | Taking down and re fixing including Calibration and cleaning of the PT pump with replacement of shaft fuel pump drive, hub coupling, gasket set and governor barrel & plunger etc.of 50 to 125 KVA |
| 118 | Taking down and re fixing including Calibration of the injector assembly with replacement of kit injector’s adjustment up to 50 KVA |
| 119 | Servicing ofAMF panel with neecessary testing including replacement ofunserviceable partsall as specified and directed by engineer in charge all as per manufacturer/authorised service centre for the following:-Note.Rate quoted shall be included attending any fault ( Start /Stop) or other defects on emergency basis of technecian for the entire period of contract .No extra cost will be paid to the contractor for the same. |
| 120 | Supply and fixing the following spares in replacement/ fixing at site for AMF panels complete all as specified and directed. |
| 121 | Supply failure timer |
| 122 | Restoration timer |
| 123 | Auxillary contactor 3 phases suitable for AMF panel . |
| 124 | NO / NC Contact - 240V A.C.,3 A.. |
| 125 | Under Voltage Relay |
| 126 | Time delay Relay |
| 127 | Contractor 4 pole 250 Amps for 125 KVA DG set |
| 128 | Contactor 3 pole MNX 80 |
| 129 | Battary Charger AMF Panel12/24 volt . |
| 130 | Controller for 82.5 KVA to 200 KVA |
| 131 | Controllerup to 63 KVA |
| 132 | AVR 3 phases for 82.5 KVA to 125 KVA |
| 133 | Contactor Relay for 82.5 KVA to 200 KVA |
| 134 | Contactor Relay for 10KVA to 50KVA |
| 135 | Repair of canopy with locks - Keys |
| 136 | HRC Fuse holders & Fuse bases range 63-160 amp suitable for Cylindrical / DIN fuse-links |
| 137 | HRC Fuse holders & Fuse bases range 80-250 amp suitable for Cylindrical / DIN fuse-links |
| 138 | HRC Fuse holders & Fuse bases range 200-800amp suitable for Cylindrical / DIN fuse-links |
| 139 | DIN type fuse links up to 160 amps |
| 140 | DIN type fuse links 200 to 400amps |
| 141 | Acrylic sheet suitable for DG set Canopy matching with existing size and thickness |
| 142 | M&L cleaning and descaling of radiator assembly by using suitable chemical (MAC solution) and by blower fan and by injecting water in high pressure in water tubings so as to remove all dirts etc in the fins complete all as specified and directed for DG set of following capacity:- |
| 143 | 320 KVA |
| 144 | 125 KVA |
| 145 | 82.5 KVA |
| 146 | Up to 50 KVA |
| 147 | M & L for Preparation of existing surface of D.G. Set at various locations capacity 12.5 KVA to 50KVA by scraping out the old existing peeled off paint layer, filling the cavities with suitable filler, making the surface smooth and applying two coats of synthetic enameled paint by spray machine including writing necessary details of D.G. Set i.e. SM No. & MES No. in the pattern and style with using synthetic enameled white paint complete all as specified and directed. |
| 148 | M & L forPreparation of existing surface of D.G. Set at various locations capacity 82.5 KVA to 320KVA by scraping out the old existing peeled off paint layer, filling the cavities with suitable filler, making the surface smooth and applying two coats of synthetic enameled paint by spray machine including writing necessary details of D.G. Set i.e. SM No. & MES No. in the pattern and style with using synthetic enameled white paint complete all as specified and directed. |
