|
| 1 | EXCAVATION & FILLINGEarth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge, All kinds of soil, As Per PWD Sch. No 251, 2.6.1 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5m. As Per PWD Sch. No 255+Sand |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. As Per PWD Sch. No 255+Sand |
| 4 | PCCProviding and laying in position cement concrete of specified grade excluding the cost of centering and shuttering :All work up to plinth level. 1:4:8 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) As Per PWD Sch. No 281 |
| 5 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. As Per PWD Sch. No 601 |
| 6 | D.P.C.Providing and laying damp-proof course 40mm thick with cement concrete1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mmnominal size) As Per PWD Sch. No 4.1 |
| 7 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer\"s specification As Per PWD Sch. No 4.12 |
| 8 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil As Per PWD Sch. No 4.13 |
| 9 | CONCRETE WORKProviding and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). : All works above plinth level upto plinth level. as per PWD Sch No. 5.33, 283 |
| 10 | All works above plinth level upto floor V level. as per PWD Sch No. 283 |
| 11 | BRICKWORKBrick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) as per PWD Sch No 6.1, 307 |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand). As per PWD Sch No. 6.4, 307 |
| 13 | REINFORCEMENT WORKSteel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level :Thermo-Mechanically Treated bars of grade Fe-500D or more. As per PWD Sch No 504 |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level:Thermo-Mechanically Treated bars of grade Fe-500D or more As per PWD Sch No 504 |
| 15 | PLASTER 12 mm cement plaster of mix: 1:3 (1 cement: 4 fine sand)As Per PWD Sch No. 584 |
| 16 | TILE WORKProviding and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. : Size of Tile 600x600 mmAs Per PWD Sch No. 11.41.2 |
| 17 | Providing and laying Vitrified tiles in different sizes (thickness to be specifiedby manufacturer), with water absorption less than 0.08 % and conforming toI.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps,over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointingwith grey cement slurry @ 3.3 kg/ sqm including grouting the joint with whitecement & matching pigments etc. complete.:Size of Tile 600x600 mm As per PWD Sch No 11.46.2 |
| 18 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thicknessto be specified by the manufacturer) of 1st quality conforming to IS : 15622 ofapproved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with greycement slurry @ 3.3 kg/sqm including pointing the joints with white cementand matching pigment etc., complete. as per PWD Sch No. 11.37 |
| 19 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. as per PWD Sch 8.31 |
| 20 | BRICK COBA TREATMENTProviding and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mmAs per PWD Sch No. 22.7.1 |
| 21 | HAND RAILINGProviding and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) as per PWD Sch No. 10.28 |
| 22 | PAINT & FINISHProviding and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete as per PWD Sch No DAR-13.80 |
| 23 | PWD 649+650Distempering with oil bound washable distemper of approved brand andmanufacture to give an even shade:as per PWD Sch No. PWD 649+650New work (two or more coats) over and including water thinnable priming coat with cement primer. as per PWD Sch No. PWD 649+650 |
| 24 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.As per PWD Sch No. DAR 13.45.1 |
| 25 | WOODEN FLUSH DOORSProviding and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)decorative type, core of block board construction with frame of 1st class hard woodand well matched teak 3 ply veneering with vertical grains or cross bands and faceveneers on both faces of shutters. as per PWD Sch No.9.235 mm thick including ISI marked Stainless Steel butt hinges with necessary screws as per PWD Sch No. 9.21.1 |
| 26 | MS WIRE GAUGE & GLASS PANESProviding & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides. As per PWD Sch 10.29.2 |
| 27 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.00 mm thick glass pane As per PWD Sch 10.30.1 |
| 28 | MS DOOR, WINDOW FRAME & SECTIONSProviding and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. As Per PWD Sch No. PWD 502(B) |
| 29 | PAINT & FINISH OF DOORS & WINDOWPainting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture, as per PWD Sch No. PWD(641+642) |
| 30 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Twoor more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.80 ltr/10 sqm of approved brand and manufacture as per PWD Sch No. PWD(641+642) |
| 31 | CHEQUERED PRECAST CEMENT CONCRETE TILELaying of 80 mm thick pre moulded inter locking paver tiles over 10 cm compected PCC including 4 cm thick fine sand bed over prepared surface including all labour T&P etc. required for proper completion of work. as per PWD Sch No. PWD 11.2Medium shade pigment using 50% white cement 50% Grey cement as per PWD Sch No. PWD 11.20.2 |
| 32 | Providing & making apron |
| 33 | Providing aluminium sliding door |
| 34 | Providing aluminium tower |
| 35 | Providing aluminium handle |
| 36 | Providing aluminium stoper |
| 37 | Providing & making drain along |
| 38 | Providing & Fixing Rain water pipe |
| 39 | Providing and Making khurra |
| 40 | Providing andFixingclips in RWP |
| 41 | Providing andFixingC.I. Grating |
| 42 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580mmx440mm with integral type foot rests (As per DSR 17.1.1) |
| 43 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. W.C. pan with ISI marked black solid plastic seat and lid. (As per DSR 17.3.2 ) |
| 44 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require.White Vitreous China Flat back wash basin size 600mmx480mm with single 15 mm C.P. brass pillar tap (As per DSR 17.7.2) |
| 45 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :. 17.5.2 Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern For gents (As per DSR 17.5.2) |
| 46 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern For ladies (As per DSR 17.5.1) |
| 47 | Providing and fixing one piece construction white vitreous china squattingplate withanintegral longitudinal flushingpipe white P.V.C. automatic flushing cistern with fittings standard size G.l.flush pipe for back and front flush with standard spreader pipe with fittings G.l. clamps and CP. brass coupling complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. Single squatting Plate with 5 liter P.V.C. automatic flushing cistern (As per DSR 17.6.1) (DSR analysis) |
| 48 | Providing & fixing flexible P.V.C. waste pipe for sink, wash basin & urinal basin including PVC waste fittings complete AS PER DSR17.28.1 a) 32mm dia DSR 17.28.1.1 |
| 49 | SOIL WASTE & VENT PIPES AND FITTINGS - IIProviding and fixing soil, waste and vent pipes 100 mm dia. centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 (As per DSR 17.35.1.2) |
| 50 | Providing and fixing soil, waste and vent pipes 75 mm dia. centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 (As per DSR 17.35.2.1) |
| 51 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter. 100 mm (As per DSR 17.58.1) |
| 52 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 75mm (As per DSR 17.58.2) |
| 53 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100 mm inlet and 75 mm outlet Sand cast iron S&S as per IS - 3989 (As per DSR 17.60.2.1) |
| 54 | Providing and fixing 600mmX450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 55 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10cmx10cmx10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 75mm (As per DSR17.37.2) |
| 56 | Providing and fixing 100mm sand cast Iron grating for gully trap. |
| 57 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100mmx100mmx100mm Sand cast iron S&S as per IS - 3989 (As per DSR 17.43.1.2) |
| 58 | Providing and fixing coller.100 mm Sand cast iron S&S as per IS - 3989 (As per DSR 17.57.1.2) |
| 59 | Providing and fixing coller. 75 mm Sand cast iron S&S as per IS - 3989 (As per DSR 17.57.2.2) |
| 60 | Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS:3989 (As per DSR 17.39.1.2) |
| 61 | Providing and fixing plain bend of required degree. 75 mm dia Sand cast iron S&S as per IS:3989 (As per DSR 17.39.2.2) |
| 62 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 63 | WATER SUPPLY PIPES AND FITTINGS-III Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 15 mm dia nominal bore (As per DSR 18.10.1) |
| 64 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work. 20 mm dia nominal bore(As per DSR 18.12.2) |
| 65 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work. 25 mm dia nominal bore(As per DSR 18.12.3) |
| 66 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 15 mm diameter pipe (As per DSR 18.38.1) |
| 67 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 20 mm diameter pipe (As per DSR 18.38.2) |
| 68 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 25 mm diameter pipe (As per DSR 18.38.3) |
| 69 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore (As per DSR 18.49.1) |
| 70 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore (As per DSR 18.50.1) |
| 71 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 15 mm nominal bore (As per DSR 18.18.1) |
| 72 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore (As per DSR 18.18.3) |
| 73 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore (As per DSR 18.53.1) |
| 74 | Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore (As per DSRDSR 18.21.2.1) |
| 75 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25mm to 40 mm nominal bore (As perDSR 18.13.1) |
| 76 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore (As per DRS 18.46.1) |
| 77 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore (As per DRS 18.46.2) |
| 78 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore (As per DRS 18.46.3) |
| 79 | EXTERNAL SEWERAGE SYSTEM-IVExcavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m. All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia (As per DSR 2.10.1.2) |
| 80 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100mm dia meter (As per DSR 19.1.1) |
| 81 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.150mm dia meter (As per DSR 19.1.2) |
| 82 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design.100mm dia meter S.W. Pipe.(As per DSR 19.2.1) |
| 83 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design.150mm dia meter S.W. Pipe.(As per DSR 19.2.2) |
| 84 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse and : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90cmx80cm and 45 cm deep including C.I. cover with frame (light duty) 455mmx610mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5(As per DSR19.7.1.1) |
| 85 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (As per DSR 19.4.2.1) |
| 86 | Extra for depth for manholes As per DSR No.19.8.1.1 |
| 87 | Wiring point for light with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in P.V.C.conduit pipepartly concealedin wall&partlylaidin slab with Piano typeswitch & ceiling rose / angle / atten holderetc complete in all respects as per PS No. 138C |
| 88 | Wiring point for fan/fresh air fan (light duty exhaust fan) with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in P.V.C conduit pipepartly concealedin wall&partlylaidin slab along with Piano typeswitch & ceiling rose / angle / batten holderetc complete in all respects as per PS No. 140C |
| 89 | Wiring point for plug with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in PVC conduit and plug point with piano switch and Soket pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting complete. FRLSH PVC insulated multistand copper conductor cable as earthwire draw inside the conduit as per PS No. 141 C |
| 90 | Wiring point for call bell with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in heavy gauge rigid steel conduit pipepartly concealedin wall&partlylaidin slab along with the reinforcement before concreting complete. FRLSH PVC insulated multistand copper conductor cable as earthwire draw inside the conduit as per PS No. 142 C |
| 91 | Wiring point for 2 way light with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in P.V.C.conduit pipepartly concealedin wall&partlylaidin slab with pianotypeswitch & ceiling rose / angle / batten holderetc. FRLSH PVC insulated multistand copper conductor cable as earthwire draw inside the conduit as per PS No. 139 C |
| 92 | Wiring point for sodium/ Street light with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in P.V.C.conduit pipepartly concealedin wall&partlylaidin slab along withmodulartype 20 Ampswitch & ceiling rose / angle / batten holderetc complete in all respects as per PS No. 143 C |
| 93 | Supply & fixing of power plugwith15amp 250 volts flush type switchand 5 pin 15 amp 250 volts flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with Phenolic Laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer as per PS No. 1139 |
| 94 | Supply & fixing of LED Street liight fitting having die cast aluminium body and diffuser with driver set suitable for 75 watt to 90 watt. Confirminig to IP 66 and above protection comlete in all respect as per PS No. 1423Category AAA |
| 95 | S/FofLED tube light with batten suitable for upto 1x22 wattcomplete in all respect. Warranty 5 Years and other condition as per New schedule No. 4615(1) dt. 21-12-18 as per PS No. 1423Category AAA |
| 96 | S/FofLED tube light with batten suitable for upto 2x22 wattcomplete in all respect. Warranty 5 Years and other condition as per New schedule No. 4615(1) dt. 21-12-18 as per PS No. 1414Category AAA |
| 97 | S/F of 15W LED bulb as per PSR |
| 98 | S/F of of single light wall bracket on matching M.D.F.E.G Board base etc complete in all respect as per PS No. 412 |
| 99 | Supply of Ceiling fans with fan motor of A.C. permanent insulation, capacitor rating, conforming BEE 5 star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated voltage 220/240 volts, 50Hz, 1-ph AC the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system as per PS No. 1501BEE 5 star rated-1200mm sweep |
| 100 | Erection and testing of ceiling fan and regulator etc. excluding supply of down rod, complete in all respect as per PS No. 1115 |
| 101 | S/F of electronic fan regulator 120-280V ISI marked, on the existing switch board including making connections, required material, Labour, T&P etc for proper completion of work to the satisfaction of Engineer in charge of work as per PS No. 1203A |
| 102 | S/F of hexagonal fan box with hexagonal/round G.P. fan box of aproved make made up of 1.0mm thick ISI mark G.P. Sheet Sport welded 4 to 8 holes of 25.4mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. sheet made upper and lower cover duly screwed fitted with 300mm round zink coted M.S. bar X 12mm & brand name should be embossed.Fixing with wiring conduit laid in the R.C.C roof before concreting along with supply of all material, labour T&P etc., for proper completion of work as per PS No. 1149 |
| 103 | S/O of Fresh air fan. 300mm size as per PSR |
| 104 | Erection and testing of fresh air fan/exhaust fan on the existing hole with suitable size of rag bolts, nuts and washers etc. complete in all respect as per PS No. 1120 |
| 105 | S/F of 16 gauge M.S. drum duly painted including making hole in the wall for fresh air fan/exahust fan and finishing properly complete in all respect as per PS No. 1122 |
| 106 | S/F of Call bell of approved make on polished MDFEG/ Teak ply board, including making connections etc complete in all respect as per PS No. 1101 |
| 107 | S/Fofsheet steel enclouser surface/flush mounting fitted with 20amp 2pin and earth metal clad scraping earth plug and socket complete in all respect as per PS No. 1031Category B |
| 108 | S/F of 63amp 415v metal clad T.P.N. rewirable type switch fuse unit on angle iron bracket complete in all respect. Cat B as per PS No. 316 |
| 109 | Supply and wiring of 4 number 16 sq. mm. P.V.C. insulated1100 volts grade singlecorecopper conductorcable in 40 mm dia PVC conduit partly concealedinwall and partly laid inslab alongwith the reinforcement before concreting, with two number 10sqmm single corev Copper conductor cable as earth continutity wiredrawn in conduit including maching colour wash etc, complete in all respects as per PS No. 279(C) |
| 110 | Supply & wiringofsubmainwithFR P.V.C. insulated1100 volts grade singlecorecopper conductorcable in heavygauge PVC conduit partly concealedinwall and partly laid inslab alongwith the reinforcement before concreting complete in all respects as per PS No. 1301C2 x 2.5 sq. mm.In 20 mm dia conduit. With 1.5 sqmm earthing contunitty |
| 111 | 2 x 4 sq. mm.In 20 mm dia conduit. With 2.5 sqmm earthing contunitty as per PS No. 221(C) |
| 112 | 2 x 6 sq. mm.In 25 mm dia conduit. With 4.0 sqmm earthing contunitty as per PS No. 222(C) |
| 113 | S/F of surface/flush mounting TPN distribution board with additional metal door without MCBcompletein all respect as directed at site by Engineer-in-charge as per PS No. CAT-A4 WAYS |
| 114 | S/F of 63 Amp 4 pole MCB (10 KA)C curve as per PS No. 1026A |
| 115 | Supply & fixingof 6 to 32 amp. SP MCB (10 KA) CAT-A as per PS No. 1020A |
| 116 | Supply and burying of 600mm X 600mm X 6mm G.I. plate veritcally for earthing with its top at least 3mtrs below ground level complete with 20mm dia G.I. Pipe and funnel for watering and one earthing lead of one no. 8 to 10 SWG G.I. wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe of and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masnory housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc complete in all respect as per PS No. 702 |
| 117 | Supply and fixing of two number 8 SWG G.I. wire in 15mm dia G.I. pipe for earthing laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site as per PS No. 723 |
