}

Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam, Arakkonam-Tamil Nadu

Military Engineer Services-MES has published Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam. Submission Date for this Tender is 29-09-2021. Fire Alarm Systems Tenders in Arakkonam Tamil Nadu. Bidders can get complete Tender details and download the document.




Tender Notice

29289939
Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam
Open Tender
Indian
Tamil Nadu
Arakkonam
29-09-2021

Tender Details

Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam Repair Maintenance Of Fire Fighting Equipments And Fire Alarm System And Connected Items In Arakkonam

Key Value

Document Fees
INR 500 /-
EMD
INR 56000.0 /-
Tender Value
Refer document

BOQ Items

Name of Work: REPAIR / MAINTENANCE OF FIRE FIGHTING EQUIPMENTS AND FIRE ALARM SYSTEM AND CONNECTED ITEMS IN ARAKKONAM (TENDER ID No. 2021_MES_463811_2)
Sl. No. Item Description
1Taking down the 3 phase, 415V, 50Hz, 7.5 HP capacity monoblock pump motor set Make: Kirloskar from terrace of highraised building (upto- G+5), lowering to ground floor, transporting to private workshop, dismantling and opening, removing burntoutwinding wire carefully cleaning the slots and rewinding of motor with super enamelled copper winding of existing gauge, insulating, varnishing, backing including servicing the pump by greasing and lubricating, reassembling, re-fixing in position commissioning and testing complete all as specified and as directed .
2Taking down the monoblock pump setwith 7.5 HP capacity motor Make : Kirloskar from terrace of highraised building (upto- G+5), lowering to ground floor, transporting to private workshop, dismantling and opening the pump , metalling the worn out shaft and replacement of NDE/ DE bearings, gland flange, gunmetal bush and lubricating the bearings and replacing the gland rope of existing size reassembling, refixing in position commissioning and testing complete all as specified and as directed .
3Taking down siren motor 3 phase 50 Hz, Make: KHIVIRAJ from terrace of buildings(upto- G+5), lowering to ground floor, transporting to private work shop, dismantling, opening, varnishing the winding wire carefully cleaning the slots backing including replacement of wornout bearings, lubricating, reassembling, refixing in position commissioning and testing complete all as specified and as directed.
4Siren 2 miles range at Akash Ganga 6 storied building.
5Siren 5 miles range.
6Taking down siren motor 3 phase 50 Hzfrom terrace of the buildings(upto- G+5), lowering to ground floor, transporting to private work shop, dismantling, opening, removing burnt out winding wire carefully cleaning the slots and rewinding of siren motor with enamelled copper winding of existing gauge, insulating, varnishing, backing including replacement of wornout bearings, lubricating, reassembling, refixing in position commissioning and testing complete all as specified and as directed.
7Siren 2 miles range at Akash Ganga 6 storied building.
8Siren 5 miles range.
9Taking down existing pump set from rusted/ corrodedfoundation by disconnecting electrically/ mechanically and kept at site and removing the corroded/ damaged mild steel foundation frame and replace with new MS frame as per existing gauge and size for 7.5 HP capacity motor including replacement of bolts, nuts with washers and applying two coats of synethic enamel paint over a coat of red oxide primer as per exisitng tint/shades complete all as specified and as directed.
10Taking down existingsiren from corroded / broken MS foundation by disconnecting electrically/ mechanically and kept at site and removing the corroded/ damaged mild steel foundationand replace with new MS frame as per existing gauge and size for siren motor including replacement of bolts, nuts with washers and applying two coats of synethic enamel paint over a coat of red oxide primer of exisitng colour shades complete all as specified and as directed .
11Taking down the existing unserviceable rusted MS pipe from floor/wall/ in trenches and ground floor to terrace (buildings upto- G+5) by dismantlingfrom wall/ terrace cutting by gas or arc welding for the following sizes complete all as specified and as directed .
12100mm dia bore pipe
13150mm dia bore pipe
14200mm dia bore pipe
1580mm dia bore pipe
16Supply and fix mild steel pipe heavy grade including all fittings from terrace /wall fixed with mild steel clamps, brackets of required size including necessary bends, reducers, flange and welding the pipe connection all in position including painting with two coat of synthetic enamel paint of approved tint over a coat of red oxide making good the disturbed portion for the following sizes complete all as specified and as directed. Note: PCC shall be measured and paid seperatly under relevent items.
17100mm dia bore pipe
18150mm dia bore pipe
19200mm dia bore pipe
2080mm dia bore pipe
21Taking down the existing unserviceable CI sluice valve, supply and fix new sluice valve with iron wheel stainless steel spindle and wedge nut with flanged of size 100mm dia, PN1.6 long body conforming to IS 14846 including replacing bolt, nuts and washers with gaskets jointing etc., complete all as specified and as directed .
22All as per item no 9 here in before but sluice valve with iron wheel stainless steel spindle and wedge nut with flanged of size 150mm dia complete all as specified and as directed .
23Taking down the existing damaged/ rusted siren motor cover, supply and fix new siren motor cover made with MS sheet 3mm thick with handle arrangement including MS flat and fixing with bolt,nuts all as per existing type/size for supporting to siren motor cover and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide primer of exisitng tint/shades complete all as specified and as directed .
24Taking down the existing unserviceable CI Non return valve supply and fix new CI Non return valves with bypass arrangement flange type PN 1.6 complete with rubber gasket, bolt and nuts, etc., complete all as specified and as directed .
2580mm dia
26150mm dia
2750mm dia
28100mm dia
29Taking down existing damaged hose 63mm dia, supply and fix hose for fire fighting 63mm dia 30m length conforming to IS636 complete with SS male and female coupling complete all as per existing specification and as directed.
30All as per item no 13 here in before but 15m length complete all as specified and as directed .
31Taking down existing damaged hose box and supply and fixing Hose box made of 18 gauge MS Sheet 800mm X 600mm X 250mm with double door with 4 mm thick glasses and door frame made of 16 gauge MS sheet painted fire red out side and brilliant white inside complete all as per existing specification and as directed.
32Taking down existing damaged glasses from hose box and supply and fixing 4 mm thick glasses with rubber gasket suitable for door frame complete all as per existing specification and as directed.
33Material and labour for painting with two coat of synthetic enamel paint of approved tint as directed on iron/ steel surfaces of any description over 10cm in width or girth including holder bats, distance pieces, etc., including cleaning the surface for free from dust and deposits complete all as specified and as directed .
34Material and labour for painting with two coat of synthetic enamel paint of approved tint as directed onpipes any description (fire hydrants, pipe lines) n.exc 60cm girth including holder bats, distance pieces, etc., including cleaning the surface of pipes and fire fighting pump house headders, air releasing vessels and suction and delivery pipes (length measured over bends, branches etc.,) complete all as specified and as directed .
35Taking down the existing damaged/ rusted centrifugal pump set cover, supply and fix new centrifugal pump set cover made with MS sheet 3mm thick with handle arrangement including MS flat all as per existing type/size for supporting to centrifugal motor cover and applying two coats of synethic enamel paint of approved tint over a coat of red oxide primer of exisitng tint/ shades complete all as specified and as directed
36Taking down the existing damaged Fire brigade inlet connection and supply and fix new Fire brigade inlet connection 2way SS complete all as specified and as directed
37Taking down the existing fire hydrant valve and supply and fix new stainless steel fire hydrant valve of size 63mm dia including replacing bolts, nuts and washers with gaskets jointing etc., and making necessary welding for anti thievery measures/ arrangements complete all as specified and as directed
38Taking down the existing unserviceable damaged gun metal female coupling flange 63mm dia and supply and fix new stainless steelfemale coupling of 63mm dia with flange 63mm dia including replacing bolt, nuts and washers with gaskets jointing etc., complete all as specified and as directed
39Material and Labour for opening the top of the Sluice valve of the following sizes carefully and taking out the gate incl spindle & checknut scrapping/Cleaning refacing, regrinding of gate of sluice valve and spindle, refixing the spindle, gate check nut and top of Sluice valve including repacking stuffing box of sluice valve spindle by replacement of gland packing rope of suitable size and reassembling including replacement of rubber gasket, Bolts, Nuts etc and making the sluice valve serviceable complete all as specified and directed
40100mm dia
41150mm dia
42Taking out the existing DOL starter from panel upto 7.5 HP capacity motor, cleaning the electronic parts from inside, replacing the unserviceable OLR, contactor, NVC etc., complete all as specified and as directed
43Taking down the existing unserviceable damaged Pressure switch from existing position and supply and fix new Pressure switch as per existing type /size / capacityincluding replacing unservicaable connecting system complete all as specified and as directed
44Dismantling all the modules of fire alarm control panel and carry out checking of all parts such as main control panel, intelligent, repeater control panel, intelligent addressable smoke detectors, addressable input/ out modules, panel moudles, indicating circuits, control circuits, manual call point, hooters, and notification appliance circuits local and remote operated terminals, etc., including testing, reassembling, trial programming with a sample of devices, replacing fault modules where necessary and retesting all the functionals such as power test, CPU fault, GND fault, disable, reset, alarm silence, panel silence, drill, alarm, SUP, trouble monitor and command menues, fire, fault, etc., and confirm serviceability of the FACP and labour charges for loop testing (address and setting programming and testing all devices in Intra panel loop) to indentify the defects in devices, loop errors and final testing and commissioning complete forfire alarm systems located at following locations all as specified and as directed
45New Magazine
46Processing unit Building
47MK-54 Building including service block
48P8I Maint hangar - 1 No.Make: HONEYWELL (upto 28 meter height)
49BSF Hanger (LRMR) & storage Accn - 1 No each .Make: APPOLO
50Four hangar - 4 Nos. Make: APPOLO(upto 28 meter height)
51Magazine - 01 No( Magazine "A" to Magazine "C") Note for item No. 26.01 to 26.07: (i) Spares required for replacement shall be measured and paid separately under relevant items as supply only and labour cost for fixing is deemed to be included in the rate quoted . (ii) Rates deemed to be inclusive of technician visiting charges and complete tools and plants like ladder, boom lift etc., all as directed by Engr-in-charge. (iii) Each Qtr complete fire alarm system to be checked and tested as per norms for system healthy, cleaning of sensors,call points etc to be carriedout and defective component if any found to be repaired/replaced (iv) If any break down occurs in fire alarm system the contractor has to repair/ rectify the fault within 24 Hrs after receiving of complaints vide any mode and incase if the contractor failed to attend the fault, penalty will be charged @ Rs 1000.00 per day/ per installation after 24 Hrs till date of defect rectification.(v) Maintaining of service register is essential for every servicingwith the signature of concern in charge (vi) Item will be measured and paid only for the Qtr in which servicing carried out and the system is in serviceable condition. (vii) Boom lift required for repair works be arranged by the contractor and will be measured and paid separately under relevant item of schedule
52Supply only the following items complete all as specified and as directed Note: Rates for labour/technician visiting charges and complete tools and plants like ladder etc., deemed to be included in item no-26 here-in-before and charges for boom lift will be paid separatly as per item No.
53Detectors complying with and type certified to EN - 45 addressable type smoke detector photoelectric / optical with base with self built intelligence as per IS: 11360. Make: Honeywell/Appolo
54Addressable type flame detectors with UV/IR detection capacity (add up cost of module to be a complete set, the type of module shall be relay type module). Make: Honeywell/Appolo
55Addressable type multi sensor with heat and smoke combination. Make: Honeywell/Appolo
56Hooter/ addressable sounder. Make: Honeywell/Appolo
57Addressable manual call point resettable type.Make: Honeywell/ Appolo
58Addressable Zone module. Make: Morley/ Honeywell/ Appolo
59Battery 7 AH.Make: Exide/TATA
60Short circuit isolator.Make: Honeywell/Appolo
61Fire alarm control panel complying with BS EN 54 upto five loop panel as required of capacity from 99 detectors & 99 modules upto 200 detector and modules all as specified and as directed.Make: Appolo/Siemens/ Honeywell
62Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep getting out in soft /loose soil for taking up/ laying pipe/cable complete all as specified and as directed .
63Returning, filling in trenches in soilin layers n.exc 25cm thick after laying of pipe / cableincluding spreading, levelling and well ramming including watering as required complete all as specified and as directed .
64Removing surplus excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above from the starting point complete all as specified and as directed .
65Supply and lay XLPEinsulated armoured heavy duty electric cables with aluminium conductor 1100 volts grade, cross sectional area 6 sqmm 4 core complete all as specified and as directed
66Material and labour for PCC in roof kerb or mud stops, rounded or chamfored on edges type C-1, 1:3:6 (Using 20mm graded stone aggregate) complete all as specified and as directed
67Supply and fixing pre fabricated readily available Pipe Support for all types of pipes including hangars / fastners / elbows/supports / tees and welding etc including taking down old corroded support all as specified and as directed
68Supply and lay PVC flexible armoured cable 2 core 1.5 sqmm complete all as specified and as directed .
69Taking down the existing unserviceable pressure gauge and supply & fixing new pressure gauge 4"dial 0-21 kgs rating in position with GI nipple in terrace of multistoried building and testing complete all as specified and as directed
70Material and labour for repairs to siren control panel including cleaning the electronic parts exists inside panel and replacing the unserviceable items like OLR,contactor,NVC,NONC ,connecting links,voubler and any other connected items etc. complete all as specified and directed.
71Taking down the existing unserviceable air release valve 25mm dia and fixing new PVC air release valve in position with GI nipple in terrace of multi-storied building and testing complete all as specified and as directed
72Taking out the existing star delta starter from panel, cleaning the electronic parts from inside and replacing the unserviceable items line the OLR, contactor, NVC, connecting link wires etc., of the following capacity motor complete all as specified and as directed
7310 HP capacity
7415 to 25 HP capacity
7530 to 75 HP capacity
76Material and labour for taking down opening motor of centrifugal main pumpset & jockey pumpsets for repair and taking out damaged/burnt out winding from three phase motor, cleaning the slots with CTC and rewinding the same with new super enamelled copper winding wire of existing gauge and turns, varnishing , bakingreassembling and fixing back into position for making motor fully functional and testing for satisfactory running complete for the following capacities complete all as specified and as directed
7710 to 15HP
7820 to 35 HP
7940 to 50 HP
80Material and labour for taking down and dismantling centrifugal main pumpset & jockey pumpsets and carrying out repairs, replacement of worn out parts such as bearings, gland metal bushes etc., and reconditioning of spare parts such as shaft, impellers, housing body etc., by metalling and machining to their original shape and size and assembling back into position by using new suitable gland dory, gland plate, gland/rubber packing including studs/gland bolts and nuts, coupling bushes etc., oiling and greasing for making pumpset fully functional and testing for satisfactory running complete for the following capacities complete all as specified and as directed:-
8110 to 15HP
8220 to 35 HP
8340 to 50 HP
84Supply and fix Sprinkler glass bulb type (Standard response) as per IS:15106/TAC guidelines 68 degree temperature rating pendent type complete all as specified and as directed
85Material and labour for galvanized iron tubing 40 mm bore light grade with all fitting laid in wall/floor/under road/culvert/on pole for protection including providing fixing clamps, bolts and nuts of suitable size as required all as specified and as directed.
86Material and labour for sub main wiring complete with 4 runs of 4 sqmm, single core, PVC insulated, unsheathed FRLS cable, 1100 volts grade,multi stranded with copper conductor, drawn through and including suitable size of steel conduit pipe and accessories on surface/ wall / roofetc. with one run of PVC insulated,4 sqmm FRLS cable, copper conductor for earth continuity conductor including taking down the old sub main wiringall as specified and as directed
87Material and labour for Earthing complete with copper earth plate electrode of size 600mm x 600mm x 3 mm thick buried directly underground vertically (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate at a depth not less than 1.5m below ground level connected with and incl Copper Earth strip 20×3mm , alternate 5 layersof charcoal &salt crystal of adequate quanty including40 mm dia GI pipe light grade by means of nuts bolts, washers and necessary earth work in any type of soil PCC (1:3:6) type C1 chamber and RCC(1:2:4)type B-1cover and watering pipe 20mm dia medium grade with funnel complete with mesh,refiling with black cotton soil all as specified . Note :- (i) Copper strip 20 x 3 mm, GI Tubing 40 mm light grade upto 7.5 mtr deemed to be included in the rate quoted by the contractor. (ii) Beyond 7.5 M earth strip & GI pipe light grade 40 mm dia shall be measured under the respective item of the schedule (iii) On testing after completion from test point the desired earth resistance shall be not more than 1 ohm .If the desired result is not obtainedthe earthing will be re done by contractor at no extra cost.
88Supply and fix copper strip 20X3mm on wall/ buried in ground including all connecting necessary arrangements all as specified and directed.
89Material and labour for preparation of old painted external surfaces of foam tank 4500 ltrs capacity and applying a two coats of synthetic enamel paint of approved tintover a coat of red oxide paint complete all as specified and as directed .
90Hiring boom lift suitable for minimum 30 mtr height for servicing, checking for repair / replacement of fire alarm system detectors / sensors and other allied items installed at Hangers , including necessary operator,fuel,T&P, safety equipments/tools complete required for safe operation complete all as specified and directed. Note: Each day is minimum of 8 Hrs ofworking
91Taking down the existing unserviceable foot valve PN 1.6 ball type and supply and fix new foot valve in position with suction line for the following sizes complete all as specified and as directed
92200mm dia
93150mm dia
9480mm dia
95Taking down the existing unserviceable butterfly valve 100mm dia supply and fix new valve arrangement flange type PN 1.6 complete with rubber gasket, bolt and nuts complete all as specified and as directed .
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail