|
| 1 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 2 | Distmantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of dismantled materials/rubbish from site complete all as specified and as directed |
| 3 | Taking down cement plaster/terrazo cast in situ of any description on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 4 | Demolition of cement concretein ground floors and pavings n exc 15 cm thickness (below or above ground level) of complete all as specified and directed. |
| 5 | Dismantling plain or corrugated steel sheeting, any guage, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed. |
| 6 | Dismantling of wall and ceiling hard boards/AC sheets(Fibre pulp insulation etc) or insulation board and plywood in any thickness & any position including cover fillets complete all as specified and as directed. |
| 7 | S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partitions of 600mm x 600mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 23mm x 28mm x 0.30mm thick, cross tee shall be 23mm x 28mm x 0.30mm thick and wall angle shall be 20mm x 20mm x 0.30mm thick complete all as specified and as directed. |
| 8 | Supply and fix 4mm thick Non asbestos fibre cement building boards (E-board) of approved texture, for insulation and acoustic purpose of size 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion diatemper over a coat of primer including preparation of surfaces completeall as specified and directed by the Engr-in Charge. |
| 9 | Materials & labour for coloured glazed ceramic tiles of size (300x200mm/350x250mm/450x350mm) of 7mm thick, as in vertical surfaces such as skirting/dado/riser to steps etc conforming to IS-13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed/backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed. |
| 10 | Material & labor for non skid coloured ceramic tiles of 7 to 8mm thick ( Square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc conforming to IS-13712, grade B-II-(a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed/bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed. |
| 11 | M&L for 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floor finished rough and even for receiving floor finishes such as tiles etc complete all as specified and as directed by Engr-in-Charge. |
| 12 | M&L for Dark/Light shade Vitrified ceramic tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed/bedding layer in cement mortar (1:6) complete all as specified and as directed. |
| 13 | M&L for Dark/Light shade Vitrified ceramic tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in verticle surfaces such as skirting/dado etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed/backing layer in cement mortar 1:4complete all as specified and as directed. |
| 14 | M&L for Digital Heavy duty Vitrified tiles (Durastone tiles ) of size 300 mm x300mm 10mm thickset , jointed and pointed in neat slurry in floors and steps with grey cement and pigments over and incl 20mm thick screed bed or bedding layer of motar for laying floor finishes in cement plaster 1:6 all as specified and as directed. |
| 15 | S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and as directed. |
| 16 | S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in ridges, valley, eaves etc fixed with self tapping screws complete all as specified and as directed. |
| 17 | S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafter and running rails and guides for sliding doors fixed with angle clear or other connecting plates conforing to Fe-410-W(Gde-E-250 quality-A)including one coat of red oxide zinc chrome primer after preparation of surfaces at contractor\"s workshop before fabrication complete all as specified and as directed. |
| 18 | M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed. |
| 19 | M&L for preparation of new/old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of super fine birla wall care putty or alteck wall care putty finish as per manufacturers instruction complete all as specified and as directed incluidng complete removal of existing treatment. |
| 20 | M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously un-treated steel surfaces of any description over 10cm in width or girth including preparation of new steel surfaces complete all as specified and as directed. |
| 21 | M&L for preparation of old painted wooden surfaces of any description, over 10 cm width or girth, not otherwise described and apply one coat of synthetic enamel paint complete all as specified and as directed. |
| 22 | M&L for preparation of newly plastered surfaces of walls and applying two coats of weather coat exterior acrylic emulsion paint white or tinted over a coat of primer as per manufacturer\"s instruction complete all as specified and directed. |
| 23 | Taking down carefully old aluminium anodised door frame alongwith fixed type door shutter complete including cutting of Glass/Frame for resizing of door and refixing door with shutter in same location after replacement/repair of frame and providing pintel hinge, door closure etc complete all as specified and as directed. |
| 24 | Material & labour for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and as directed. |
| 25 | Excavation in post holes (or similar holes) in soft/loose soil each n.exc 0.5 Cum, getting out, returning, filling in an ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm and removing surplus soil to a distance n.exc 50 mtrs complete all as specified and as directed by the Engr-in-Charge. |
| 26 | Taking down rainwater pipes (any size or pattern), including all fittings,heads, shoes,bends, swan-necks, etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by the Engr-in-Charge. |
| 27 | S&F PVC (SWR) half round 150mm bore with rounded edges incl all accessories like bend T etc for eaves gutter complete all as specified and directed. |
| 28 | S&F in repairs 110mm bore, PVC(SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors including necessary earthwork, fixed on walls complete all as specified and as directed. |
| 29 | Supply and fix in repairs 110mm bore PVC(SWR) bend of any radius for PVC (SWR) pipes/steel gutters etc, fixed to walls complete all as specified and as directed. |
| 30 | Supply and fix 110mm bore PVC(SWR) junction single, (Single T ) equal or unequal with access door complete all as specified and as directed. |
| 31 | S&F for ISI Mark floor door closer of stainless steel single cylinder floor spring set for wood/aluminium/glass door with weight up to 90Kg with all fittings and fixture complete all as specified and directed. |
