Public Works Department-PWD has published Construction Of Multi Story Parking And Office Accommodation ( Armsdale Phase-Iii ) At Chotta Shimla. ( Sh- Providing And Placing Modular Furniture Items ) . C / O Multi Story Parking And Office Accommodation ( Armsdale Phase-Iii ) At. Submission Date for this Tender is 18-08-2021. Building Work Tenders in Chotta shimla Himachal Pradesh. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 06-Aug-2021 | Pre-bid | Other | 11-08-2021 |
| 2 | 09-Aug-2021 | Corrizemdum | Other | 18-08-2021 |
| 3 | 09-Aug-2021 | Deadline for submission of Bid | Date | 18-08-2021 |
| Sl. No. | Item Description |
| 1 | Providing and placing at site Workstation Modular partitions 60mm thick and width as per layout /Drawings .The different shape joineries are used to attach standard partition modules. The frame work of partition is of extruded aluminum consists of vertical side bar of 60 mm width ,Top& Mid horizontal bar of 60mm width and wire race way section of 81x36mm provided with race way cover of 100mm width .The mid horizontal section of partition is placed at 750 mm working top height with a provision of holding brackets of working top .All different section of partitions are screwed .On box type frame betweenmid-bar& bottom race way made of 25 mm thick pre-laminated medium density fibre/particle board(/ ) covered with 8 mm thick particle pre-laminated decorative board(/) on both sides of frame and another box type frame between top & mid bar made of 25 mm thick pre-laminated medium density fibre/particle board (/)havingpin up soft board with choice fabricor white marker board .However, the partition between mid-bar & top bar can be provided with semi frosted glass,by using special glass extruded aluminum section. The different extruded aluminum section provided with Top trim of D shape of 60 mm width on three side with self-locking provision of sections .The PVC caps /covers of same colors are used on ends, L shape joineries, T shape joineries and four way joineries, depends on layout of partition. For the joining of partition modules in L shape the semicircular 68mm vertical section is used at joinery and for T shape placement of modules 60mm vertical T cover is used at joinery. All extruded aluminum section used in partition are well powder coated with 70-80 micron powder coating of approved shade. The partitions are also provided with PVC levelers on brackets fitted on bottom of side bars which allow 14mm adjustment for unevenness of floor.-Worktop of 25mm thick pre-laminated medium density fiber/particle board ofmake and all the exposed edges provided with machine pressed 0.8mm thick PVC edge bands glued with hot melt EVA glue. The working top of having cable manager. The sidemade of 18mm pre-laminated medium density fiber/particleboard ofmake and having attachment for fixing of work station to the modular partition and each workstation provided with Drawer unit size 450x500x735 made of 18 mm pre-laminated medium density fiber/particleboard ofmake of interior grade of approved shade, all panels of unit are inter connected with rastex , dowel and sockets (of Hettich make) having three drawers(two box drawers of std. size and one file drawer) fitted on ball telescopic full extension channels ,with centre locking system(lock of Hettich make).The drawers are provided 96mm SS handles. All the edges provided with machine pressed 0.8mm thick PVC edge bands glued with hot melt EVA glue. The unit is also provided with key board made of 18mm pre-laminated medium density fiber/particleboard ofmake fitted on ball based full extension telescopic channel with mounting brackets.-CPU TROLLEY This shall be made of HR steel sheet duly powder coated of thickness 50 microns minimumwith 50 mm dia castors (nylon) to provide mobility. The width of CPU shall be adjustable complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge:- |
| 2 | Work Station Size 1650mmx1650mmx 1050mm. |
| 3 | Work Station Size 1500mmx1500mmx1050mm with three drawer unit, key board, CPU Trolley. |
| 4 | Work Station Size 1200mmx600mmx1050mm with three drawer unit, key board, CPU Trolley. |
| 5 | Providing and placing at site Executive Table size 1650mmx1650mmx750mm with side return unit, three drawer unit. Table size 1650mmx1650mmx750mm having top edges 36mm thick of particle board ofhaving profiled edges and post formed with .6mm thick high pressure laminateand exposed edges of top provided with machine pressed .8mm thick PVC edge bands glued with hot melt EVA glue, the side panels of 25mm and modesty panel made of 18mm pre laminated particle board of make Action tesa of interior grade duly interconnected and attached to top with rastex, dowel and sockets of Hettich make. All the edges of under structure provided with machine pressed 0.8mm thick PVC edge bands glued with hot melt EVA glue. The top is also provided with cable manager On right as well as left side. The unit is also provided with key board made of 18mm pre-laminated medium density fiber/particleboard ofmake fitted on ball based full extension telescopic channel with mounting brackets. Side unitSize 900x450x725 having top 25mm thick of particle board ofhaving profiled edges and post formed with .6mm thick high pressure laminateand exposed edges of top provided with machine pressed .8mm thick PVC edge bands glued with hot melt EVA glue,the under structure made of 18mm pre laminatedparticle board of make Action tesa of interior grade duly interconnected and attached to top with rastex, dowel and sockets of Hettich make havingkey board fitted on full extension ball based telescopic channel with mounting bracketsand space for CPU & UPS under key board, the unit is having a cupboard having one shelf making two compartments with shutter fitted on snap on hinges. All the edges of under structure provided with machine pressed 0.8mm thick PVC edge bands glued with hot melt EVA glue. The unit is also provided with three drawers size 450mm x 500mm x 700mm made of 18 mm pre-laminated particle board of make Action tesa of interior grade of approved shade, all panels of unit are inter connected with rastex, dowel and sockets of Hettich make having three drawers(two drawers of std. size and one file drawer) with SS 96mm handles and fitted on telescopic side mounted ball based channels with full extension with centre locking system of Hettich make. All the edges provided with machine pressed 0.8mm thick PVC edge bands glued with hot melt EVA glue complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 6 | Providing and placing at site Executive Table size 1500mmx1200mmx750mm with side return unit, three drawer unit. Table size 1500x1200x750 having top edges 25mm thick of particle board ofand exposed edges of top provided with machine pressed .8mm thick PVC edge bands glued with hot melt EVA glue, the side panels of 25mm and modesty panel made of 18mm pre laminated particle board of make Action tesa of interior grade duly interconnected and attached to top with rastex, dowel and sockets of Hettich make. All the edges of under structure provided with machine pressed 0.8mm thick PVC edge bands glued with hot melt EVA glue. The top is also provided with cable manager On right as well as left side. The unit is also provided with key board made of 18mm pre-laminated medium density fiber/particleboard ofmake fitted on ball based full extension telescopic channel with mounting brackets. The unit is also provided with three drawers size 450x500x700mm made of 18 mm pre-laminated particle board of make Action tesa of interior grade of approved shade, all panels of unit are inter connected with rastex , dowel and sockets of Hettich makehaving three drawers(two drawers of std. size and one file drawer) with SS 96mm handles andfitted on telescopic side mounted ball based channels with full extension with centre locking system of Hettich mak e. All the edges provided with machine pressed 0.8mm thick PVC edge bands glued with hot melt EVA glue complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 7 | Providing and placing at site Perforated Bench (Cushioned) Chair- Seat: High Quality cold rolled sheet is perforated, pressed and welded to form the shape. The surface is then cleaned with acid to remove rust and electrostatically coated with epoxy powder and then cured under heat to allow it to form a “skin” Thickness- 1.2 mm. The seat & back padded with high density cushions and upholstered with best quality fabric/Leatherite. Decorative Edge: High quality metal is bent to form the shape. The surface is then polished and chrome plated. Arm/Leg: High quality mild steel sheet is pressed and welded to form the shape. The surface is then polished and chrome plated. Thickness-1.2mm Cross Bar: High Quality cold rolled sheet is pressed and welded to form the shape and the surface is then cleaned with acid to remove rust and powder coated. Thickness-2mm. Three Seater Overall Dimension : Width : 690mm Height: 790 mm Length: 1820 mm complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 8 | Two Seater Overall Dimension: Width : 690mm Height: 790 mm Length: 1200 mm complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 9 | Providing and placing at siteAuditorium Chair (Push Back ) Total Height form floor : 1015mm Width Center to Center : 560 mm Depth : 750 mm Seat Height: 450 mm Arm Height: 600 mm Side leg: 50x2 mm chanel Grouting supporting Plate Welded :80x305x4 mm Back and Base Covered by PPCP cover thick 4mm Back Assemble The back made in Head PU foam 50 density inserted frame of 19x2mm CR tube support by nylon belt for swinging comfort. Back size is 700x465x110 mm Seat Assemble The seat is push back and made of PU foam upholster with fabric 100% polyester and inserted in PU 19mm round cr pipe. Seat Size 500x460x130mm. The chair is provided with Fix back and seat push back Arm Rest The armrest is made in PP with cup Powder Coating All metal components are powder coated in black colour 70-80 micron complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 10 | Providing and placing at site MID BACK CHAIR SEAT/BACK ASSEMBLY : The Cushioned seat should bemade of Injection molded Plastic outer & inner. Plastic Inner should beupholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgffor 25% compression.The Cushioned back should bemade of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D), BACK SIZE : 46.5 cm. (W) x 59.5 cm. (D) ARMRESTS: The armrest top should bemoulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should bedesigned with the following features: • 360° revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should bemade up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT: Seat depth adjustment should beintegrated in the seat through a sliding mechanism. Seat depth adjustment range should beof 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should beconnected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY The pedestal should beHigh Pressure Die cast polishedAluminium and fitted with 5 nos. twin wheel castors. The pedestal should be65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should beinjection mouldedin Black Polypropylene. Overall Dimensions of Chair -: Seat Height -44.5-54.5cm., Height -96.5 - 114cm. Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 11 | Providing and placing at site HIGH BACK CHAIR The seat and back shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam shall be designed with contoured lumbar support for extra comfort. The seat shall be extra thick foam on front edge to give comfort to popliteal area. The dimensions of back shall be 47.5 cm(W) x 69.5 cm(H) and of seat shall be47.0 cm (W) x 48.0 cm (D). The HR polyurethane foam shall be moulded with density= 45±2 kg/m3 and hardness load 16 ± 2 kgf as. per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co.polymer Polypropylene. The mechanism shall be designed with 360° revolving type, Upright-position locking, Tilt tension adjustment, Seat/back tilting ratio of 1:3. The pneumatic height adjustment shall has an adjustment stroke of 12.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 42.5 to max 54.5cm, Height - min97.0 to max 109.0cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. |
| 12 | Providing and placing at siteMID BACK CHAIR The seat and back shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam shall be designed with contoured lumbar support for extra comfort. The seat shall be extra thick foam on front edge to give comfort to popliteal area. The dimensions of back shall be 47.5 cm(W) x 58.0 cm(H) and of seat shall be47.0 cm (W) x 48.0 cm (D). The HR polyurethane foam shall be moulded with density= 45±2 kg/m3 and hardness load 16 ± 2 kgf as. per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co.polymer Polypropylene. The mechanism shall be designed with 360° revolving type, Upright-position locking, Tilt tension adjustment, Seat/back tilting ratio of 1:3. The pneumatic height adjustment shall has an adjustment stroke of 12.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal shall be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 42.5 to max 54.5cm, Height - min85.5 to max 97.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 13 | Providing and placing at siteVISITOR CHAIR The seat and back shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam shall be designed with contoured lumbar support for extra comfort. The seat shall be extra thick foam on front edge to give comfort to popliteal area. The dimensions of back shall be 47.5 cm(W) x 58.0 cm(H) and of seat shall be47.0 cm (W) x 48.0 cm (D). The HR polyurethane foam shall be moulded with density= 45±2 kg/m3 and hardness load 16 ± 2 kgf as. per IS:7888 for 25% compression. The tubular frame shall be cantilever type & made of dia 2.54±0.03cm.x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated(DFT 40-60 microns). The one-piece armrests shall be injection moulded from black Co.polymer Polypropylene. Overall Dimensions of Chair shall be Seat Height - 46.5cm, Height - 89.5cm, Width & Depth of Chair as measured from pedestal - Width-61.4 cm and Depth-64.5 cm complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 14 | Providing and placing at site TWO SEATER SOFA Upholstery • Material : Leatherite • Thickness : 1 mm Frame : • Material : Combination of plywood and pine Wood • Plywood thickness : 12 mm (moisture resistance and termite free) • Pinewood cross section ( without knots)- 22x64 mm - 34x64 mm - 16x35 mm Seat : • Material : Slab stock foam • Density : Base 28 kg/m3 and super soft 32 kg/m3 at top Back : • Material : Slab stock foam• Density : Super soft 32 kg/m3 with a layer of siliconized conjugated polyster fiber of 200 gsm Webbing • S spring of dia. 3.8 mm mounted on seat structure using plastic spring mounting clip. Legs : PVC complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 15 | Providing and placing at siteCOFFEE TABLE Table With a black and glass top base, The table is crafted from an 8 mm tempered glass top and a silver powder coated understructure, which adds resilience to the table. The table also has a 6 mm tempered bottom glass for storing all essentials. Table Loading capacity : 30 Kg. Size - Width - 110 cm, Height - 50 cm, Depth - 60 cm complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 16 | Providing and placing at siteCONFERENCE TABLE (PER SEAT) Encarta Conference Table size shall be for one seat ( 1) 675 Width mmx 600 D epth mmx 750 Height mm . Top shall be 25 mm PLB thick With PVC beading all over . In Understructure legs shall be made from 18 mm thick PLT having curved profile plus Modesty shall be made from PLT (pre - laminated twin ) boards 18 mm thick in two shades . Wire manager shall be running along the width of desk fitted on the modesty panel from inside complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 17 | Providing and placing at site CHAIR SEAT ASSEMBLY: The seat assembly is made of polyurethane foam moulded with M.S. tubular frame insert which is upholstered with fabric. The insert is tubular frame made of 01.9 ±0.02cm x 0.16 ±0.013cm thk MS. E.R.W round tube with flexible support straps running across the length and width of the frame.The Seat has an auto-tipup feature making it stay in upright position when not in use enabling clear row passage.* Approx. Seat Size : 45.5cm (W) x 46.5cm (D). BACKREST ASSEMBLY: The back assembly has a flexi back mechanism. It is made of polyurethane foam moulded with M.S. tubular frame insert, Upholstered with fabric and has a plastic back cover. The insert is a tubular frame made of 01.9 ±0.02cm x 0.16 ±0.013cm thk M.S.E.R.VV round tube with flexible support straps running across the length and width of the frame.*Approx. Back Size : High Back- 45.5cm (W) x 82.4cm (H). ,Mid Back- 45.5cm (W) x 70.4cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-3 kg/m3.SIDE PANEL / AISLE PANEL:The chair rests on the ground on two side panel frames fabricated from 0.12 ±0.020cm thk CR steel sheet which is cladded with fabric upholstery. The side panel frame is grouted to the floor using 2 nos. of anchors for each panel through 0.3 ± 0.05cm thk HR steel base plate. PU ARMREST (FOR MARSHB/MB069XXPU FIXED ARM): The armrest is made up of integral skin Polyurethane Foam with 65 +/- 10 Shore "A" Hardness and reinforced with wooden insert. The armrest is snapfitted with sidepanel. POWDER COATING: Steel components are epoxy polyester powder coated (DFT 40-60 microns). FLOORING PRE - REQUISITE : The auditorium chair is designed to get mounted/grouted on floors with flooring specification as mentioned in flooring pre-requisitedoc-no: STG 129368. High Back CENTRE TO CENTRE (C) : 58.7 cm. DEPTH (D1) : 50.5 cm. WIDTH (W1) : 67.5 cm. DEPTH (D2) : 63.0 cm. WIDTH (W2) : 50.7 cm. DEPTH (D3) : 83.6 cm DEPTH (D4) : 97.6cm SEAT HEIGHT (SH): 45.5 cm. HEIGHT (H) : 107.3cm Mid Back CENTRE TO CENTRE (C) : 58.7 cm. DEPTH (D1) : 50.cm WIDTH (W1) : 67.5 cm. DEPTH (D2) : 62.0 cm WIDTH (W2) : 50.7 cm. DEPTH (D3) : 82.7 cm DEPTH (04) : 93.7cm SEAT HEIGHT (SH) : 45.5 cm. HEIGHT (H) : 95.3 cm complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. ABLE (PLT) - PER SEAT Worksurface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure : It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Modesty Panel : Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns) Wire Management : An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated(DFT 40-60 microns) is used for flow of wires and cables. Provision to mount AnchorRoma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. |
| 18 | Providing and placing at site Auditorium cum desk:- A)Legs: - Legs are made of MS ERW tube section (157138) of size 75x25x2 mm thick oval tube with 5 mm thk HR brackets as per IS:2062 and 2mm thk CRCA brackets as per IS-513welded on to the tubes. Assembly is powder coated with epoxy polyester. - Leg height varies from 705 to 1005 in pitch of 50 as per layout. - Sturdy anchoring by anchor bolts on to base of 8mm thk plate for proper resting of Leg**. - Shoe made of ultramid -Nylon are provided at the bottom for covering the base plate. B)Side dads: - Two side clads made of e18 mm thk plate with 0.8mm thk pvc lipping and on the outside covered with welded metal structure made of 2 mm thk CRCA as per 1S-513 powder coated with Epoxy polyester . C)Worktop: - Worktop are made of 25 mm thick Pre-Laminated Board of El-P2 Grade and approved shade conforming to IS:12823:1990. All the edge of work surface are provided with machine pressed 2mm thick pvc edge band glued with hot melt glue. D)Seat: - Seat has self closing mechanism which will operate by means of dead weight Seat understructure is made from combination of welded fabricated structure of 5mm Thk HR as per IS:2062 and 8mm thk ply as per 1S:303 with moulded PU foam of density 55 kg/cu.mtr. on top which in turn is covered with stitched upholstery made of leatherite as per INT/DSN/MSS/UPH1038 or foam back fabric as per TNT/DSN/MSS/UPH/013. Seat assembly is covered on bottom side by means of seat cover made of pp. E)Seat Back: - Seat back is made from combination of 8mm thk ply as per 15:303 with moulded foam on top which in turn is covered with stitched upholstery made leaterite as per INT/DSN/MSS/UPH/038 or foam back fabric as per INT/DSN/MSS/UPHJ013. F) Seat Support Frame :- Seat support frame is made from combination of MS ERW tube section (IS 7138) of size 80x40x2.5 mm thick rectangular tube and MS ERW tube section(IS 7138), of size 48x19.1x2 mm thick oval tube welded together . Assembly os powder coated with Epoxy polyester. CAP made of ultramid are provided from front to cover the oval tubes. G)Modesty: - Modesty is made of 25mm thick pre-laminated twin board of E1-P2 Grade and approved shade conforming to IS:12823:1990. All the edge of modesty are provided with machine pressed 2 mm Thick pvc edge band glue with hot melt glue complete including carriage of materials within all leads and lifts as per direction of Engineer-in-charge. |
| 19 | Conditions:-i) Rates should be quoted for all leads, lifts and all heights irrespective of any floor level etc. ii) The tapestry cloth to be used shall be of Seasons / Vimal make or equivalent as approved by the Engineer -in-Charge. Iii) The Bidder shall attach authorization of the Principle Manufacturer / Company that he is authorized to bid in this specific tender on his behalf.Copy of Proof should be attached. iv)The Bidder shall attach the Balance Sheet, Profit and Loss Statement for the last five years duly issued by the Charted Accountant which should not be in loss. V) For working-out the bid capacity, the turnover amount for last five years forcivil work including furniture should be specifically separated out which should be issued by the charted accountant. vi) The Bidder should never have been blacklisted / Debarred by any organization & shall attach affidavit duly notarized on Non Judicial Stamp Paper for the same. vii)The Bidder / Principle Manufacturer / Company shall attach the experience for successfully executed similar wooden furniture orders during the last five financial years & value of any one of such single order (without Liquidated Damage or Compensation) should be minimum amounting to Rs. 108.50 Lac (Rs. One hundred eight Lac and fifty thousend ) only. Certified copy of completion certificate issued by the client department (Govt/Semi Govt.) dully signed by an officer not below the rank of Executive Engineer or equivalent in this regard needs.( to be attached to be read with Eligilibity criteria claim No. 26.2b).viii) The successful Bidder shall supply one sample of each and every item at site of work in advance within 15 days of award of work for approval from the competent authority. After approval of samples he can execute the work for supply of total quantity as per agreement.ix) TheBidder / Principle Manufacturer / Company should have their own plant and machinery to execute the work. He should have to submit an Affidavit in this regard duly notarized.. x) The Bidder should have attach affidavit duly notarized for warranty of materials for five years and amount of securitywill be released after three years after the issue of the certificate final or otherwise of completion of work or till the final bill. xi)All the amounts such as for work done, work in hand and experience etc. should be supported with authentic documentary proof i.e. certificate not below the rank of Executive Engineer or equivalent of any Government / semi Government department. In case of turnover etc. only certificate of a registered Charted Accountant shall be considered. xii) Bid of any bidder not qualifying any of the above condition or of bid documents shall be rejected during finalization of technical bids and his financial bid shall not be opened. Xiii)Furniture\ items shall be finalized by the constituted committee. xiv)If there is increased/ decreased in size/ quantities of items same shall be paid on pro-rata basis. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
