| 1 | 1 | Excavation in foundations ,trenches etc, in earth work,lift upto 1.50mtr.stacking the excavated soil not more than 3 mtr clear from the edge of the excavation and than returning the stacked soil in 15 cm layers, when required into plinths side of foundations etc consolidating each depo-sited layer by ramming and watering excavated eath as directed with in in a lead of 20 mtrs, P&J work 50% each. | | 63 | P/Cum |
|---|
| 2 | 2 | Providing and laying cement concrete 1:3:6( 1cement 43sand:6 graded stone aggrigate 40 mm nominal size and curing complete excluding the ost of form work in foundation and plinths. | | 3.6 | P/Cum |
|---|
| 3 | 3 | Proiding and laying cement concrete work 1:2:4( 1cement : 2 sand : 4 graded stone aggrigate 20 mm nominal size and curing complete exclud-ing cost of form work and reinforcement for reinforced concrete work in | | | |
|---|
| 4 | 4 | (i)Foundations,footings,bases of columns and the like and mass conc. | | 8.97 | P/Cum |
|---|
| 5 | 5 | (ii) Columns,pillars,posts and struts upto floor two level. | | 6.39 | P/Cum |
|---|
| 6 | 6 | (iii)Suspended floors,roofs,landings and shelves and their supports balconies,beams,girders,bressumers and cantolever upto floor two level | | 34.48 | P/Cum |
|---|
| 7 | 6.01 | Providing mild steel/Tor steel reinforcement for R C C work including bending,binding and placing in position complete upto floor two level (Tor steel) | | 2773.85 | Kg |
|---|
| 8 | 6.02 | Providing form work with steel plates 3.15mm thick so as to give fair finish including centring,shuttering,strutting and propping etc. Height height of propping and centering below supporting floor to ceiling not exceeding below supporrting floor to ceiling not exceeding 4 mtr. And removal of the same for insitu reinforced concrete and plain concrete work in | | | |
|---|
| 9 | 6.03 | Flat surface such as soffis and suspended floor roofs and landing | | 130.56 | P/Sqm |
|---|
| 10 | 6.04 | Vertical surface such as Column.pillar,beams,cantilever & post upto floor two level square, rectangular& polygonal & post upto floor two level square, rectangular& polygonal in plan. | | 293.56 | P/Sqm |
|---|
| 11 | 6.05 | Providing and fixing pressed steel door, frames, manufactured from comercial mild steel sheet of 1.25 mm thickness including hinges jump block Jamb, beed, and if required angle threshold of mil steel angle of section 50x25mm or base ties of 1.25mm pressed mild steel welded or regidly fixed together by machanical means adjustable lugs with split and tails to each Jamb i/c steel but things 2.5mm thick with guards lock strike plate and shock as specified and applying a coat of applying steel primer after pretreatment of the surfaces directed by the Engineer-in-charge | | 139.7 | P/Rmt |
|---|
| 12 | 6.06 | Providing and fixing panelled glazed as panelled and glazed shutters for door ,windows, and C. S. window including black enamelled iron butt hinges with necessary screws(40 mm thick 2nd class deodar wood | | 57.06 | P/Sqm |
|---|
| 13 | 6.07 | P/F wire gause shutters using MS wire gause of IS gause designation 85G for doors windows clerestorey windows I/c bright finished black enamelled iron hinges with necessary secrews 30 mm thick 2nd class deodar wood. | | 55.26 | P/Sqm |
|---|
| 14 | 6.08 | Half brick masonry in common burnt clay bricks in super structure above plith level upto floor two level---Ist class bricks in mortar 1 : 4 ( 1 cement : 4 sand ) | | 128.64 | P/Sqm |
|---|
| 15 | 6.09 | 15 mm thick plastering single coat on rough side of brick/stone mason-ary for interior plastering upto floor two level including arrises internal rounded angles chamfers and /or rounded angles not exceeding 80 mm in girth and finished even and smooth.in cm1:6 (1cement : 6sand ) | | 257.28 | P/Sqm |
|---|
| 16 | 7 | 6 mm thick plaster to ceiling with cement mortor1:3 (1 cement 3 sand) | | 130.56 | P/Sqm |
|---|
| 17 | 7.01 | White washing with lime on undecorated wall surface two coats to give and even shade including throughly brooming the surface to removel of all dirt dust mortor dirt and other foreign matter. | | 387.84 | P/Sqm |
|---|
| 18 | 7.02 | Distempering with Oilbond distemper of approved brand and manufacture (Two coats) and of required shade on undecorated wall surface to give hly brushing the surface free from mortar dropping and other foreign matter | | 259.86 | P/Sqm |
|---|
| 19 | 7.03 | Applying priming coat over new wood and wood based surfaces after & including perpering the surface by throughly cleaning oil, grease,dirt and other foreing sand papering and knotting . Readymixed paint brushing with white lead for priming | | 114.12 | P/Sqm |
|---|
| 20 | 7.04 | Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including clearing the surface dirt,dust, and other foreing matter sand papering and stoping .with white enamel paint | | 114.12 | P/Sqm |
|---|
| 21 | 7.05 | Providing 40x3mm flat hold fast 10 cm long fixing the frame with 10mm diameter bolts,nuts and embending in cement concrete block. 30 x 10 x 15cm.1:3:6 (1cement :3sand:6graded stone aggrigate 20mm n/s ) | | 108 | Each |
|---|
| 22 | 8 | Providing and fixing sliding door bolt brought finished black enamalled with nut and scraw complete 300X16 mm long. | | 20 | Each |
|---|
| 23 | 9 | Providing and fixing mild steel handles with necessary screw complete 100 mm long. | | 24 | Each |
|---|
| 24 | 10 | Providing and fixing tower bolt bared type with necessary screws complete 150x10 mm. | | 80 | Each |
|---|
| 25 | 11 | Boulder / Stone filling under flooring dry hand packed tightly. | | 24.51 | P/Cum |
|---|
| 26 | 11.01 | Providing and laying cement concrete 1:6:12( 1cement :6 sand: 12 grad- ed stone aggrigate 40 mm nominal size and curing complete excluding cost of form work in foundation and plinths. | | 24.51 | P/Cum |
|---|
| 27 | 11.02 | Precast terrazo tiles 20m thick (with marble chipsof specified shadeand of specified laid in floor treads of steps and landingon bed on10mm thick cement plaster 1:6 (1cement6sand) jointed withneat cement | | 90.76 | P/Sqm |
|---|
| 28 | 12 | Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement: 3sand:6graded stone agg. 20mm nominal size) i/c finishing the top surface of concrete smooth within all leads and lifts and as directed by the Engineer-in-charge. | | 18.96 | P/Sqm |
|---|
| 29 | 12.01 | Providing senitary fitting & electricity wiring with all assesories i/c fitting by using a of good quality with ISI mark,complete in all material respect | | 2 | Each |
|---|
| 30 | 12.02 | Providing and fixing anodiased coated aluminioum work of door windows ventilators and partions with extuded built up standard tubar and other sections of approved make conforming to Is 733 and Is 1285 anodized transparent or dyed to required shade according to Is 1868 fixing with dash fasteners of reqired dia and size including necessary filling up the gaps at junctions i.e at top bottom and sides with required EPDM rubber /neoprene gaskit etc aluminium sections shall be smooth rust free straight mitred and jointed mechanically wherever required including cleat angle aluminium sanp beading for glazing / paneling C.P brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing , paneling and dash fasteners to be paid for separately ) : for fixed portion powder coated aluminium (minimum thickness of powder coating 50 micron ) | | 679.38 | kg |
|---|
| 31 | 13 | Providing and fixing anodiased coated aluminioum work of door windows ventilators and partions with extuded built up standard tubar and other sections of approved make conforming to Is 733 and Is 1285 anodized transparent or dyed to required shade according to Is 1868 fixing with dash fasteners of reqired dia and size including necessary filling up the gaps at junctions i.e at top bottom and sides with required EPDM rubber /neoprene gaskit etc aluminium sections shall be smooth rust free straight mitred and jointed mechanically wherever required including cleat angle aluminium sanp beading for glazing / paneling C.P brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing , paneling and dash fasteners to be paid for separately ) : for shutters of doors windows & ventilators incliding providing and fixing hinges / pivots and making provision for fixing of fittings wherever reqired including the coast of EPDM rubber/ neoprene gasket required (fitting shall be paid for separately ) powder coated aluminium (minimum thickness of powder coating 50 micron ) | | 216.05 | kg |
|---|
| 32 | 14 | Providing and fixing aluminium door stoper with rubber cushion 100 mm including carriage of materials within all leads and lifts :- | | 22 | Each |
|---|
| 33 | 15 | Providing and fiiing glazing in aluminium door windows shutters with PVC neopene gaskets etc as per arch Drg and the direction of Engineer in charge 5mm thick within a leds and lifts direction of Engineer in charge | | 78.9 | P/Rmt |
|---|
| 34 | 15.01 | Providing and fixing glazing in aluminium door, window,ventilator,shutter and partitions etc.with EPDM rubber/neoprene gasket etc.complet as per the architectural drawing and the direction of Engineer in charge.floaqt glass panes of 5.50mm thickness | | 234.24 | /sqm |
|---|
| 35 | 15.02 | Providing and fixing aluminium round shape handle of outer dia 100mm with ss screws etc.complete as per direction of ingineer in charge powder coted minimum thickness 50 micron aluminium. | | 11 | /nos |
|---|
| 36 | 15.03 | Providing and fixing 100mm bras locks (bestmake of approved quality) for aluminium door including necessery cutting and making good etc.complete. | | 11 | /nos |
|---|
| 37 | 15.04 | Providing and fixing ISI marked oxidised ms torbolts aluminium finish(barrel type) with necessary screws etc.complete: | | 11 | /nos |
|---|
| 38 | 16 | Providing and fixing ISI marked oxidised ms pressed butt hings with necessary screws etc. Complete.100mm. | | 24 | /nos |
|---|
| 39 | 16.01 | Providing and fixing 4mm thick ACP sheet in type ii in panelling fixed in aluminum doors ,windows shutters and partition frames with C.P Brass /stainless steel screws etc complete as per architectural drawinges and directions of engineer in charge | | 109.56 | P/Sqm |
|---|
| 40 | 16.02 | Demolition below G.L. upto\n1.50Metres depth and disposal\nof unserviceable materials\nwithin 20 metres lead. Un-reinforecd cement concrete upto 15 cm. Thickness. | | 1.95 | P/Cum |
|---|
| 41 | 17 | Steel work welded in built up sections, trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of red lead paint. | | 29.78 | qtl |
|---|
| 42 | 18 | ROOFING Providing and fixing 0.60mm th. Prepainted steel sheet in roofing with hot dipped metallic zinc coated sheetwith top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat polyster of 5microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks,bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete all accesories as required as per the direction of Engineer- IN- Charge | | 66.3 | sqm |
|---|
| 43 | 18.01 | Providing and fixing ridges or hips 60 cm overall with 0.60mm thick Prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating + back coat polyster of 5microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks,bolts and nuts 6mm dia metre with prepainted G.I. limpet and bitumen washers complete with all accesories as required as per the direction of Engineer- IN- Charge . | | 3.15 | Rmt. |
|---|
| 44 | 19 | Providing and fixing 30 cm. wide 30 cm.deep 90 cm overall semicircular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design.0.63 mm thick sheet. including carriage of materials within all leads and lifts :- | | 6.6 | Rmt. |
|---|
| 45 | 20 | Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) | | 9.9 | sqm |
|---|
| 46 | 21 | Providing wood work in frames of false celling partitions etc. sawn and put-up in position complete including carriage of materials within all leads and lifts:- 2nd class KALI wood | | 1 | cum |
|---|
| 47 | 22 | Providing and fixing wooden plank ceiling with planks over lapping each other and jointed with wood screws (frame work to be paid for separately) | | | |
|---|
| 48 | 23 | 20mm thick 1st class D/Wood including all leads and complete) including carriage of material within all leads and lifts as per direction of Engineer-in-charge. | | 122.72 | sqm |
|---|
| 49 | 24 | Providing and fixing (beading 40mmx45 mm section i/c mitring at junctions with wood screws and nails complete. | | 149.88 | Rmt. |
|---|
| 50 | 25 | Polishing two or more coat with lacquuer polish on new wood & wood based surface to give an even surface including cleaning the surface of all dirt and dust and sand prepared smooth & including a coat of wood filler complete as directed by the Engineer-in-charge 40mm thick. | | 122.72 | sqm |
|---|
| 51 | 26 | Providing and fixing 19mm thick water proof termite resistant commercial kit ply (gold) board or equivalent in shelves/box for cup board with butt joints & fixing with nails & screws etc complete) including carriage of material within all leads and lifts as per direction of Engineer-in-charge.\n | | 178.98 | sqm |
|---|
| 52 | 27 | P/f 12mm thick prelaminated board both side bwp phenol bonded exterior /interior grade shutter with frame | | 40 | sqm |
|---|
| 53 | 28 | Providing and fixing brass double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315) for aluminium / wooden door including cost of cutting floor as required embedding in floors and cover plates etc. complete as per the direction of Engineer-In-Charge I/c making good the floors. | | 50 | nos |
|---|
| 54 | 29 | Providing and fixing brass over head hydraulic Hinges door closer of approved brand and manufacture (conforming to IS specification ISI marked) for door with screws complete as per the direction of Engineer-In-Charge . | | 30 | nos |
|---|
| 55 | 30 | Providing and fixing magnetic catcher (M-15) including carriage of materials within all leads and lifts. | | 30 | nos |
|---|
| 56 | 30.01 | Providing and fixing ornamental 20mm dia brass hanger rod with brackets on both ends with screws etc complete including carriage of materials within all leads and lifts. | | 60 | Rmt. |
|---|
| 57 | 30.02 | Providing and fixing ornamental brasscoat hooks strip with six hooks fixed with rawl plugs & screws etc. complete including carriage of materials within all leads and lifts. | | 20 | nos |
|---|
| 58 | 30.03 | Providing and fixing brass 100mm morice latch and lock with six levers and a pair of handles and knobs including necessary screws etc. as approved by the engineer-in-charge complete including carriage of materials within all leads and lifts. | | 15 | nos |
|---|
