| 1 | 1 | S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed. | | 70 | Sqm |
|---|
| 2 | 2 | S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed. | | 10 | Sqm |
|---|
| 3 | 3 | M&L for rendering 10 mm thick on concrete surface in cement mortar (1:6) as backing coat and 5 mm th in CM 1:4 using finishing the surface even and smooth without using extra cement, including mixing only liquide water proofing compound as per manufacturer instruction including taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MD land all as specified and as directed. Note:- WPC will be measured & Paid separately | | 660 | Sqm |
|---|
| 4 | 4 | M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:-\n(i) Taking out old roof treatment and roughening the same old concrete slab by picking, sweeping clean and washing down with water to remove dust etc.and applying cement slurry @3kg/Sqm\n(ii) Screed bed or bedding layer of mortar 1:4 in 15 mm thick for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (Note: WPC shall be measured and paid for under separate items)\n(iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986.\n(iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction.\n(v) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm. | | 130 | Sqm |
|---|
| 5 | 5 | Supply only for liquid water proofing compound. | | 20 | Kg |
|---|
| 6 | 6 | M&L for 10mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement including preparation of new plastered/concrete surfaces of walls, providing 1mm thick of white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint and including taking down cement plaster in cement or cement lime mortar on brick or concrete walls etc. including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MoD land complete all as specified and as directed. | | 620 | Sqm |
|---|
| 7 | 7 | M&L for 5mm thick plaster in cm (1:4) on fair faces of concrete surfaces of ceiling including finishing even & smooth without using extra cement including taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MoD land all specified and directed. | | 185 | Sqm |
|---|
| 8 | 8 | M&L for preparation of new plastered surfaces of ceiling and providing 1mm thick of white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed. | | 30 | Sqm |
|---|
| 9 | 9 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. | | 155 | Sqm |
|---|
| 10 | 10 | M&L for preparing newly plastered surfaces of external wall and applying two coats exterior acrylic emulsion paint (Ist quality) over a coat of primer as per manufacturer instruction complete all as specified and directed. | | 660 | Sqm |
|---|
| 11 | 11 | M&L for complete removal of existing old treatment of any description and preparation of old surfaces ,washing rubbing down and applying two coats exterior acrylic emulsion paint (Ist quality) over a coat of primer as per manufacturerS instruction complete all as specified and directed. | | 1900 | Sqm |
|---|
| 12 | 12 | Complete removal existing treatment and applying 1mm thick of Birla white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and as directed. | | 2000 | Sqm |
|---|
| 13 | 13 | M&L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. | | 890 | Sqm |
|---|
| 14 | 14 | M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. | | 450 | Sqm |
|---|
| 15 | 15 | M&L for preparation of old decorated plastered surfaces of ceiling and applying one coat of distemper oil emulsion on ceiling complete all as specified and directed. | | 1700 | Sqm |
|---|
| 16 | 16 | S&F false ceiling of Non asbestos fibre decorative cement building boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 605 mm x 605 mm x 4 mm thick fixed over and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 605mm X 605mm x605mm.The aluminium frame work will supported on side wall with the used of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia. Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long including dsmantling wall and ceilling boards of any description including cover fillets complete all as specified directed by the Engineer-in-Charge. \n\nMake : Everest or equivalent as approved by GE. | | 50 | Sqm |
|---|
| 17 | 17 | M&L Non-skid ceramic colour tiles (premium/special quality) 7 to 8 mm thick , (square/rectangular), area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:4 including dismanthing floor/hearth or wall tilling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off premises complete all as specified and as directed. | | 58 | Sqm |
|---|
| 18 | 18 | M&L Non - skid Ceramic colour tiles (premium/special quality) 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement sand mortar 1:4 etc.complete all as specified and as directed. | | 110 | Sqm |
|---|
| 19 | 19 | M&L Glazed ceramic colour tiles of size 450 x 300 x 7mm thick (premium/special quality) in vertical wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 including dismanthing floor/hearth or wall tilling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off premises complete all as specified and directed. | | 134 | Sqm |
|---|
| 20 | 20 | M&L Glazed ceramic colour tiles of size 450 x 300 x 7mm thick (premium/special quality) in vertical wall etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tile over and including 10 mm thick backing course in cement sand mortar 1:4 etc complete all as specified and directed. | | 264 | Sqm |
|---|
| 21 | 21 | Demolition of plain cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) Including removal of debries out side MoD land complete all specified and as directed | | 56 | Cum |
|---|
| 22 | 22 | M&L for PCC 1:3:6 type C2 (using 40 mm graded aggregate) as in plinth protection 75mm thickness, finished even and smooth using extra cement including 10mm wide and 30mm deep joints at every 2.4mtrs interval filled with mastic compound etc complete all as specified and as directed by Engr-in-Charge. | | 90 | Sqm |
|---|
| 23 | 23 | Taking down chowkhats or frame with shutter without taking off shutter from the frame not exc 1.50 sqm & removing from site complete all as specified and directed. | | 108 | Each |
|---|
| 24 | 24 | Taking down chowkhats or frame with shutter without taking off shutter from the frame exc 1.50 sqm but not exc 4 sqm each & removing from site complete all as specified and directed. | | 3 | Each |
|---|
| 25 | 25 | Taking down shutter of any description exc 1 Sqm but not exc 2.00 sqm each complete all as specified and directed. | | 5 | Each Leaf |
|---|
| 26 | 26 | Supply and Fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. | | 14.4 | Sqm |
|---|
| 27 | 27 | S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed. | | 16 | Sqm |
|---|
| 28 | 28 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and as directed. | | 235 | RM |
|---|
| 29 | 29 | S&F Factory Made Solid PVC Moulded Door Shutter with particle board core , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed. | | 68 | Sqm |
|---|
| 30 | 30 | Supply and fixing 100mm size butt hinges cold rolled medium weight, ISI marked complete all as specified and directed. | | 159 | Each |
|---|
| 31 | 31 | S & F 150mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. | | 96 | Each |
|---|
| 32 | 32 | S & F 150mm long Aluminium anodised, barrel tower bolts of extruded\nsection and fixed complete all as specified and as directed. | | 96 | Each |
|---|
| 33 | 33 | Supply and fixing Flush shutters, solid core construction 30mm thick with block board core and plywood face panels, commercial type on both sides conforming to IS-2202(Part-I), 1983 complete all as specified and directed. | | 9 | Sqm |
|---|
| 34 | 34 | S & F Pressed steel frames for doors of size 105mmx60mm , 1.25 mm thick with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed. | | 13 | RM |
|---|
| 35 | 35 | S & F 200mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed. | | 10 | Each |
|---|
| 36 | 36 | S&F 150 mm size MS pressed handle oval type stove enameled block complete all as specified and directed. | | 10 | Each |
|---|
| 37 | 37 | S & F Mild steel sliding door bolts of size 250 mm, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed | | 5 | Each |
|---|
| 38 | 38 | S&F Sheet glass 3 mm thick, ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane including fixed with wooden beads/glazing pins or spring clips in wooden or metal frames complete all as specified and as directed. | | 11 | Sqm |
|---|
| 39 | 39 | S&F 3mm thick sheet glass ordinary quality & glazing with oil putty or fitted with wooden beads in squares n.exc. 0.50 sqm in each pane including hacking out old broken glass with puty or fixed with wooden bends complete all as specified and directed. | | 10 | Sqm |
|---|
| 40 | 40 | S&F 3 mm thick frosted on one side sheet glass ordinary quality & glazing with oil putty or fitted with beads in squares n.exc. 0.50 sqm in each pane complete all as specified and directed. | | 18 | Sqm |
|---|
| 41 | 41 | Supply and fixing in repairs 250mm long MS sliding door bolt, plate type, stove enameled black with bright bolt not less than 12mm dia with and including a min of siz bolt & nuts four on bolt & two on staple,ISI marked, complete all as specified and directed. | | 8 | Each |
|---|
| 42 | 42 | Supply and fixing in repair 200mm size MS barrel tower bolt stone enamelled black with bright bolt ISI marked complete all as specified and directed. | | 15 | Each |
|---|
| 43 | 43 | Supply and fixing in repair 150mm size MS pressed handle oval type stove enameled block complete all as specified and directed. | | 15 | Each |
|---|
| 44 | 44 | Resecuring or easing & adjusting without taking down the shutter of any description exc 1 Sam and n.exc 2 Sqm in same opening complete all as specified and directed. | | 20 | Per leaf |
|---|
| 45 | 45 | M&L for preparation of wood and wood based materials new surface of any description and girth 10cm wide other wise described applying two coat of synthetic enamel paint over a coat of primer complete all as specified and directed by Engr-in-Charge. | | 25 | Sqm |
|---|
| 46 | 46 | Forming jambs, etc. to openings CM 1:6 (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete | | 49.5 | sqm |
|---|
| 47 | 47 | M&L for preparation of new steel surface and applying of two coat of synthetic enamel paint over a one coat of red oxide exc 10cm width or girth all as specified and directed by Engr-in-charge. | | 28 | Sqm |
|---|
| 48 | 48 | M&L for PCC 1:3:6 type C2 (using 40mm graded aggregate) as in surface channels and drains including necessary formwork complete all as specified and as directed. | | 5 | Cum |
|---|
| 49 | 49 | Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. | | 70 | RM |
|---|
| 50 | 50 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. | | 24 | Each |
|---|
| 51 | 51 | S & F in repair Vitreous china squatting pan of pattern Orissa Pattern of size 580x 440 mm white with 110mm bore PVC ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( 1:5:10, using 40 mm graded stone aggregates), and finishing the top surfaces to match with the existing flooring as in repairs. | | 24 | Each |
|---|
| 52 | 52 | S & F Vitreous china wash hand under counter oval shaped basin with fixing acessories set, white coloured of size 595 mm x 420mmx200mm mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia complete all as specified and as directed by Engineer-in-Charge.' Make : Jaquar Cap Pat No : CNS-WHT-705 or equivalent series in KOHLER/Roca/Hindware. | | 12 | Each |
|---|
| 53 | 53 | S & F in repair 32mm size Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed. | | 12 | Each |
|---|
| 54 | 54 | S & F in repair PVC low level white flushing cistern 9/10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, brass screws, handle, 32 mm dia PVC flush pipe of suitable length and making all connection and making good disturbed surface complete all as specified and directed. | | 24 | Each |
|---|
| 55 | 55 | S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. with grating and union for discharge pipe all as specified and as directed by Engineer-In-Charge. | | 6 | Each |
|---|
| 56 | 56 | S & F in repair 40mm Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed. | | 10 | RM |
|---|
| 57 | 57 | S & F 1000 litres capacity white tripple layer, rotational molded, polythene water storage tank, ISI Marked (Cylindrical vertical with closed top),colour white , hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete incl dismantling water tanks and removing to store. | | 12 | Each |
|---|
| 58 | 58 | S & F 15 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors including taking down up or down complete all as specified and directed. | | 180 | RM |
|---|
| 59 | 59 | S & F 20 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors including taking down complete all as specified and directed. | | 90 | RM |
|---|
| 60 | 60 | M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete. | | 50 | RM |
|---|
| 61 | 61 | S & F in repair 25mm bore Gun-metal, globeor gate valves,with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. | | 6 | Each |
|---|
| 62 | 62 | S&F in repair 15 mm size Angular stop cock complete all as specified and directed. Make : Hindware Cat No.F200005 equivalent series in KOHLER/Roca/Jaquar | | 48 | Each |
|---|
| 63 | 63 | S & F in repair 15 mm bore CP fancy type bib tap long body cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. | | 48 | Each |
|---|
| 64 | 64 | S&F in repair of 15mm dia pillar taps fancy type, cast copper alloy, with capstan heads chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts screwed for iron pipe fixed complete all as specified and directed. | | 18 | Each |
|---|
| 65 | 65 | S & F in repairs PVC Connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed. Make: Prayag/Polytuf | | 48 | Each |
|---|
| 66 | 66 | M & L for 125mm size Brass chromium plated shower rose with or without swivel joints, any size completed all as specified and an as directed. | | 24 | Each |
|---|
| 67 | 67 | S&F in repair brass chromium plated tubular towel rail 600mm long between the flanges and 20mm dia complete all as specified and directed. | | 24 | Each |
|---|
| 68 | 68 | S & F in repairs to 600mm long PVC flexible Waste pipe to WHB/urinals/Sink complete all as specified and as directed. | | 18 | Each |
|---|
| 69 | 69 | S & F 100mm bore cast iron soil, waste and vent sand cast pipe in any length, with or without ears fixed with cement joints laid in trenches or in floors including dismantling of cast iron or reinforced concrete drain pipes 100mm, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. | | 20 | RM |
|---|
| 70 | 70 | S & F 75mm bore cast iron soil, waste and vent sand cast pipe in any length, with or without ears fixed with cement joints laid in trenches or in floors including dismantling of cast iron or reinforced concrete drain pipes 75mm, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. | | 30 | RM |
|---|
| 71 | 71 | S & F 100mm bore cast iron soil, waste and vent sand cast pipe in any length, with or without ears fixed with cement joints laid on wall including dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar complete all as specified and directed. | | 15 | RM |
|---|
| 72 | 72 | S & F 75mm bore cast iron soil, waste and vent sand cast pipe in any length, with or without ears fixed with cement joints laid on wall including dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar complete all as specified and directed. | | 12 | RM |
|---|
| 73 | 73 | Refixing of 100mm bore cast iron soil, waste and vent sand cast pipe in any length, with or without ears fixed with cement joints laid on wall or bore 100 mm including dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar complete all as specified and directed. | | 40 | RM |
|---|
| 74 | 74 | Refixing of 75mm bore cast iron soil, waste and vent sand cast pipe in any length, with or without ears fixed with cement joints laid on wall or bore 100 mm including dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar complete all as specified and directed. | | 25 | RM |
|---|
| 75 | 75 | S & F in repair 100m size vent cowl complete all as specifeed and directed. | | 6 | Each |
|---|
| 76 | 76 | S&F in repair 100 mm dia bore CI oval access door bend (any radius) diminishing pieces or tapers (Larger bore measured) complete. | | 24 | Each |
|---|
| 77 | 77 | S&F in repair 75mm dia bore CI oval access door bend (any radius) diminishing pieces or tapers (Larger bore measured) complete all as specified and as directed. | | 24 | Each |
|---|
| 78 | 78 | S &F in repair 100mm bore cast iron Single 'Y' junctions laid and jointed, complete all as specified and as directed. | | 10 | Each |
|---|
| 79 | 79 | S&F in repair cast iron Nahani trap 100 mm dia of outlet, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) using 20 mm graded stone aggregate complete. | | 36 | Each |
|---|
| 80 | 80 | M&L for plan cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate, (Avg 50 mm thickness) in sunken for padding to achieve the 1:40 slope complete all as specified and as directed. | | 5 | Cum |
|---|
| 81 | 81 | M&L for plan cement concrete 1:5:10 type E2 using 40 mm graded stone aggregate, as in foundations/sunken,filling and mass concrete complete all as specified and as directed. | | 41 | Cum |
|---|
| 82 | 82 | M&L for water proofing treatment to sunken portion of RCC slab with the following courses of treatment/specification :- (i) For Screed bed or bedding layer of mortar 1:4 in 15 mm thick for laying as in sunken portion with mixing of WPC and surface finished fare and smooth without using extra cement. (Note: WPC shall be measured and paid for under separate items)\n(ii) Preparation of plastered roof surface and applying one coat of cold bituminous primer @ 0.25 ltr /Sqm conforming to IS:3384-1986.\n(iii) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied by torch application over bituminous primer as specified. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. Note:-The work of sunken portion treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer. Contractor shall submit documentary evidence on support of applicator engaged for approval of GE. | | 150 | Sqm |
|---|
| 83 | 83 | Demolition of Precast cement concrete block walling in any position, Including removal of debries out side MoD land complete all specified and as directed. | | 7 | Cum |
|---|
| 84 | 84 | M&L Precast PCC (1:3:6) type C1 (using 20mm graded agg) solid block masonry exc 10cm in width or girth and setting CM (1:6) complete all as specified and directed. | | 3 | Cum |
|---|
| 85 | 85 | M & L for Providing precast cement concrete type C1, 1:3:6 (using 20mm graded stone aggregate) solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed setting in mortar 1:4 , complete, in walls complete all as specified and as directed. | | 38 | Sqm |
|---|
| 86 | 86 | Dismantling of stone slabs and granite laid, bedded and pointed in any mortar of any description or thickness in floors, aprons cills or plateform etc Including removal of debries out side MoD land complete all specified and as directed. | | 5.85 | X SM |
|---|
| 87 | 87 | M & for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. | | 9 | Sqm |
|---|
| 88 | 88 | M&L for rounding to edges of stone slabs one edge, such as in steps cooking plateform, and other similar situation complete all as specified and as directed. | | 9 | RM |
|---|
| 89 | 89 | M&L for Pre cast RCC 1:1.5:3 type A1 using 20 mm graded stone aggregates as in cover slab for soakage well / manhole and similar works supported on walls including formwork set in cement mortar 1:6 including demolition of cement Concrete (RCC) of any description and in any position not otherwise specifically provided for complete. Note:- Reinforcement steel will be measured & paid sepratly. | | 0.6 | Cum |
|---|
| 90 | 90 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including bending, and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge. | | 50 | Kg |
|---|
| 91 | 91 | S & F of 2nd class hard wood scantling, clean sawn in any position and any description as in unframed work including dismantling of timber scantling 40 sqcm and over in section in any position complete all as specified and as directed. | | 3.5 | Cum |
|---|
| 92 | 92 | Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats creosote oil complete all as specified and as directed. | | 165 | Sqm |
|---|
| 93 | 93 | Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section of unframed work complete all as specified and as directed. | | 455 | RM |
|---|
| 94 | 94 | M&L for 2nd class hard wood plain fillets bullnosed, splayed, chamfered or rounded on one edge or face in section clean sawn, fixed with screws sec are exc 6sq cm n exc 13 sq cm complete all as secified and as directed. | | 195 | RM |
|---|
| 95 | 95 | M&L for 2nd class hard wood plain fillets bullnosed, splayed, chamfered or rounded on one edge or face in section clean sawn, fixed with screws sec are exc 3 Sq cm and n exc 6 sq cm complete all as specified and as directed. | | 260 | RM |
|---|
| 96 | 96 | M&L for preparation of new wooden surfaces of any description n.exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. | | 26 | 10 Rm |
|---|
| 97 | 97 | S& F of 4 mm thick Non asbestos cement plain building boards, fixed to timber frame work with screws fixed in ceiling, flat or sloping including dismantling of ceiling board of any description complete all as specified and directed. | | 215 | Sqm |
|---|
| 98 | 98 | M & L for Machine pressed precast concrete interlocking paver block of approved shape and size 60mm thickness, with minimum compressive strength of 60 N/Sqmm (M-35Grade) without correctin factor for chamfering , made in rubber moulds with 0.5mm thick scratch proof lacquer coating on top surface , with white cement a, confirming to IS 15658-2006 complete all as specified and directed. | | 107 | Sqm |
|---|
| 99 | 99 | M&L for cement concrete 1:4:8, type D-2, using 40 mm graded stone aggregate, as in Sub base for floor all as specified . | | 9 | Cum |
|---|
| 100 | 100 | M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. | | 3 | Cum |
|---|
| 101 | 101 | M& L for Machine cut kota stone slab flooring 18 to 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15 mm thick screed bed in CM 1:4 complete all as specified and directed | | 15 | Sqm |
|---|
| 102 | 102 | Taking down carefully old unserviciable copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, sunken type box etc. and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge. | | 185 | Each Point |
|---|
| 103 | 103 | M&L for concealled point wiring for modular fittings with 1.5 Sqmm (nominal area) PVC insulated1100 volts grade, multistranded, copper conductor, single core, unsheathed cables (FRLSH quality) drawn through and including PVC conduits of suitable size but not less than 20 mm dia (medium grade) with all fittings and accessories including suitable PVC modular box or pressed steel modular boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint both internally and externally including cover plate with frame concealed in walls/ceiling etc and including cutting chases for conduits and sinking for boxes and making good to disturbed surfaces, including PVC insulated and unsheathed, single core, multi-stranded, copper conductor cable of size 1.5 Sqmm green in colour as earth continuity conductor connected to common earth and earth dolly for one light point/fan point controlled by one 5 Amps one way switch complete as specified and directed. Note : Quoted rate shall be inclusive for necessary chasing and cutting and making good . | | 91 | Each Point |
|---|
| 104 | 104 | All as per item No 103 above but for one 3 pin socket outlet 5 Amps on same board alongwith other suitable switches. | | 5 | Each Point |
|---|
| 105 | 105 | All as per item No 103 above but for one 3 pin socket outlet 5 Amps on independent board alongwith other suitable switches. | | 60 | Each Point |
|---|
| 106 | 106 | All as per Srl item No.103 here in before but for one light point controlled by two way switch/fan regulators. | | 2 | Each Point |
|---|
| 107 | 107 | All as per item No 103. above but with 2.5 sqmm cable for 3/5 pin 15 Amps switch socket outlet (Power point) complete all as specified. | | 27 | Each Point |
|---|
| 108 | 108 | Supply and fixing of modular switch one way 6 amps 1 module 230/250 Volts complete all as specified/directed. Make: Legrand/L&T/Schneider | | 156 | Each |
|---|
| 109 | 109 | Supply and fixing of modular switch two way 6 amps 1 module 230/250Volts complete all as specified/directed. Make: Legrand/L&T/Schneider | | 4 | Each |
|---|
| 110 | 110 | Supply and fixing of modular socket outlet 2/3 pin 6 Amps 230/250 volts 2 module complete all as specified/ directed.Make: Legrand/L&T/Schneider | | 65 | Each |
|---|
| 111 | 111 | Supply and fixing of modular switch one way 16 amps 1 module 230/250 Volts complete all as specified/directed. Make: Legrand/L&T/Schneider | | 27 | Each |
|---|
| 112 | 112 | Supply and fixing of modular socket 6/16 Amps, 230/250 volts, 2/3 pin combined, 2 module complete all as specified and directed.Make: Legrand/L&T/Schneider | | 27 | Each |
|---|
| 113 | 113 | Supply and fixing ceiling rose, 3 terminal PVC/polycarbonate, isolated body complete all as specified and directed. Make : Anchor/SSK/Havells | | 171 | Each |
|---|
| 114 | 114 | Supply and fixing LED batten fittings 1x18/20 Watt complete pre wired fixed to wall with 2 nos PVC block of suitable size make Havells Cat no LHEXACP7PN1W018 or PHLIPS Model no DX18 UJJWAL or Crompton cat no LCTL 20 CDL . | | 155 | Each |
|---|
| 115 | 115 | S & F wall mounted LED batten fittings with all accessories 1X 10 Watt LED, extruded polycarbonate, integrated electronic driver and fixed to wall with 2 Nos PVC block suitable size complete all as specified and as directed including taking down old unserviceable light fittings Make - Havells Cat no LHEXACP7IN1W010 or Crompton cat no LCTL 10 CDL or equivalent inPhilips | | 6 | Each |
|---|
| 116 | 116 | S&F lamp holder, insulated body, with back plate for batten fitting including 7 watt LED lamp 625lm, B22 complete. Make of holder- Havells/anchor/Legrand, Make of LED: Phillips/Bajaj/Havells | | 60 | Each |
|---|
| 117 | 117 | Material and labour for concealed sub main wiring with two single core 6.0 sqmm FRLSH,PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC conduit pipe (Medium grade) of suitable size complete all as specified and directed, including taking down unservicable one.(Note: two run of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC conduit pipe shall be measured as one length).\n | | 50 | RM |
|---|
| 118 | 118 | Material and labour for concealed sub main wiring with two single core 4.0 sqmm FRLSH,PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH, PVC insulated multistranded copper conductor cable of size 4.0 sqmm green colour as earth lead including PVC conduit pipe (Medium grade) of suitable size complete all as specified and directed, including taking down unservicable one.(Note: two run of 4.0 sqmm cable , one run of earth wire of 4.0 sqmm and one run of PVC conduit pipe shall be measured as one length).\n | | 250 | RM |
|---|
| 119 | 119 | Supply and fixing Distribution board SPN , 240 volts single pole and neutral ,double door, sheet steel enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted on wooden board with electrical connection complete all as specified and directed including taking down old one. Make: Havells Cat part No DHDPSHODRW08 or equivalent in Schnieder/GE. | | 15 | Each |
|---|
| 120 | 120 | Supply and fix MCB, DP, 240 Volt, 32 Amps, 10 kA rupturing capacity 'C' series, AC complete all as specified and directed by Engr-in Charge. Make: Havells Cat Part No:DHMGCDPF006-032 or equivalent in Schnieder/ABB. | | 12 | Each |
|---|
| 121 | 121 | Supply and fix MCB, DP, 240 Volt, 40 Amps, 10 kA rupturing capacity 'C' series, AC complete all as specified and directed by Engr-in Charge. Make: Havells Cat Part No:DHMGCDPF040 or equivalent in Schnieder/ABB. | | 3 | Each |
|---|
| 122 | 122 | Supply and fix MCB, SP, 240 Volt, 40 Amps, 10 kA rupturing capacity 'C' series, AC complete all as specified and directed by Engr-in Charge. Make: Havells Cat Part No:DHMCCSPF006-32 or equivalent in Schnieder/ABB. | | 3 | Each |
|---|
| 123 | 123 | Supply and fix MCB, SP, 240 Volt, 6-32 Amps, 10 kA rupturing capacity 'C' series, AC complete all as specified and directed by Engr-in Charge. Make: Havells Cat Part No:DHMCCSPF006-32 or equivalent in Schnieder/ABB. | | 120 | Each |
|---|
| 124 | 124 | Supply and fix in repairs MCCB Distribution board, VTP&N , loadline , double door, ,sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link,415 Volts 4 way fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Havells Cat part No DHDLVDRWGOFO04 or equivalent in Legrand/Schnieder/GE/C&S. | | 1 | Each |
|---|
| 125 | 125 | Supply and fix as in repairs MCCB four pole , 415 Volt, 125 Amps,25 KA , fixed thermal & magnetic setting complete all as specified and directed .Make:- Make: Havells Cat Part No: IHLGHF0125# or equivalent model from Make:- Siemens / Schneider / Legrand / L&T. | | 1 | Each |
|---|
| 126 | 126 | Supply & fixing blank plate fixed on MCB's DB where applicable complete all as specified & directed by Engr -in-Charge. | | 20 | Each |
|---|
| 127 | 127 | S & F in repairs exhaust fan 230 volts , 250mm,plastic body Ventilator DX including making all electric connection complete all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall Make Orient/Bajaj/Havell's/ CG Note:- Old unserviceable exhaust fan obtained after taking down shall be deposited to MES store.. | | 6 | Each |
|---|
| 128 | 128 | Supply and fixing Building light LED 25 Watt including connection with three core cable 1.5 sqmm complete all as specified and and directed. Make:- Bajaj Cat part No- BRLEP 25W LED WH or Havells Cat No-ENDURACITYLITE25W or equivalent in Phillips | | 4 | Each |
|---|
| 129 | 129 | M&L Earthing complete with galvanized steel earth plate electrode 60cmx60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 m deep below normal ground level, connected to GI earth lead wire 4.0 mm dia means of nuts, bolts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 connected to earthing test point protected by and including GI pipe 15 mm bore (light grade) and connected to main test point as directed and including concrete pit in PCC (1:3:6) type C-1,pre cast RCC (1:1½:3) type A-1 cover slab 54cm x 54cm x 5 cm, reinforced with 8mm dia TMT bars @ 150 mm C/C both ways with one handle for lifting, made out of 8mm dia TMT bar embedded in pre cast cover slab , funnel, wire mesh, 20 mm bore GI pipe (medium grade) for watering, charcoal and salt in alternate layers, including necessary excavation and earth work in any type of soil complete all as shown on electrical Plate No 3 of SSR Part-I, and testing and taking down old one complete all as specified and as directed . | | 2 | Each Job |
|---|
| 130 | 130 | Supply, laying connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power cable (heavy duty) with stranded aluminium conductor, 1100 Volts grade, cross sectional area 50 Sqmm, 3.5 core laid through duct/pipe/in trench, etc. including taking out old unserviceable cable complete all as specified and directed. NOTE: Excavation and earth work will be measured and paid separately.\n | | 45 | RM |
|---|
| 131 | 131 | M&L for brick laid for LT underground cables protection to with sub class 'B' over burnt brick, (locally available best quality), laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and directed. | | 100 | Each |
|---|
| 132 | 132 | Supply and fix as in repair GI pipe of 25mm of light grade under road, on pole etc for cable protection complete all as specified and directed. | | 18 | RM |
|---|
| 133 | 133 | Excavation in trenches in hard/dense soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable and erection of poles all as specified and directed at site. | | 3 | Cum |
|---|
| 134 | 134 | Removing of surplus excavated material n.exc 50 m and depositing where directed at a level not exceeding 1.5 meter above the starting point in soft soil complete all as specified and directed. | | 1.5 | Cum |
|---|
| 135 | 135 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and directed. | | 1.5 | Cum |
|---|
| 136 | 136 | M&L for sand cushioning to under ground cable using locally available fine clean dry river sand over, under ground UG cable laid in trenches and gently punning done complete all as directed by Engineer-in-Charge. Note : For the purpose of payment only punned thickness will be measured.\n | | 1.2 | Cum |
|---|
