| 1 | 1 | R2-CS-SS-13 Supplying, fabricating, transportation to site and Fixing Galvanized Chain Link Fencing of 10 gauge G.I. Mesh, sizes 50 x 50 mm diamond pattern, fixed 75 mm below finished ground level / coping, including providing and erecting ISA 50x50x6 angle posts @ 2.5m C/C with cross support at every 8th pole & at corners and 2 nos 6mm dia MS bars at top and bottom with necessary U hooks, nuts and bolts, washers, total height of fencing @ 2.0m above ground including embedding the angle post in concrete block of 0.45m x 0.45m x 0.6m of cement concrete M15 grade including necessary excavation, and cleaning, preparing the surface, applying one coat of red oxide zinc chromate primer and two coats of Synthetic Enamel paint of approved manufacture, brand, colour, shade etc. complete as directed by Engineer In Charge. (first coat of synthetic enamel paint after fabrication and second coat after erection including touching up the primer coat) | A1 | 500 | Sqm |
|---|
| 2 | 2 | R2-CS-SS-15 Providing, detailing, and fabricating as per specifications, transporting to site and erecting MS Openable / Sliding / Ornamental Entrance Gates including track and wheel, locking arrangement, fixing bolts, nuts, washers, cleats, stiffeners, gussets decorative balusters, arrow heads etc. and all necessary operations like straightening, bending, cutting, drilling, grinding, machining if specified, welding etc. complete weighing 25 to 30 kg/Sqm, including cleaning, Grinding and removing the welding burr and preparing surface and applying one coat of red oxide zinc chromate primer and one coat of Synthetic Enamel paint after fabrication and second coat of Synthetic Enamel paint after erection, with approved colour, shade and brand etc. including touching up with primer etc. complete as directed by Engineer In Charge.(Structural material and paint is in contractor scope ) | A2 | 150 | Sqm |
|---|
| 3 | 3 | NIT rate, Item no.1, CES-190216073 Detailing, fabricating and fixing at desired location using hot rolled sections and MS Plates of grade Fe250 as per specifications and approved fabrication drawings (which are to be prepared by Contractor and got approved from Engineer), transporting to site and erecting structural steel members for all heights & at all levels including provision of necessary erection bolts, fixing bolts, nuts, washers, cleats, stiffeners, gussets, base plate, and all necessary fixtures and operations like preheating as per specifications, straightening, bending, cutting, drilling, grinding, machining if specified, welding, grinding and removing the welding burr and preparing surface for painting with wire brush cleaning and applying two coats of epoxy red oxide zinc phosphate primer of 30 microns each and two coats of Epoxy Corrosion Resistant Enamel paint of 30 microns after fabrication including touching up with spray painting after erection etc complete as directed by Engineer In Charge. (The qty. for this item shall be measured for gusset plates, base plates, bolts in M.T.) (Steel and paint shall be supplied by RCF) | A3 | 10 | MT |
|---|
| 4 | 4 | R2-CS-RW-09-a Providing and fixing single skin trapezoidal profiled sheeting 930 - 1020mm cover width 28-32 mm crests depth at 186-250 c/c ( above 195 mm c/c crest distance there will be minimum 2 ribs at the centre for stiffening). The feed material shall be manufactured from AZ 150 (min. 150 gms/sq.mt total on both sides) Zincalume / Galvalume sheets of minimum yield strength of 550 MPa, 0.45 mm BMT, ( 0.5 mm TCT excluding paint coating thickness), metallic hot dip coated with Al-Zn alloy (55% Aluminium, 43.5% Zinc, 1.5% Si ) as per AS 1397 / IS15961 & painted with Super Durable Polyester Colorbond steel XRW or equivalent quality paint system of apporved color, suitable for exterior application conforming to AS/NZS 2728:2007 type-4 / IS15965:class3 of approved make. The sheet shall have a total coating thickness of 35 microns, super durable polyester paint system of 20 microns on exposed surface and 5 micron reverse polyester coat on back surface over 5 micron primer coat on both surfaces. The paint system shall have stable inorganic pigments for color durability. The product will be fastened using no.12-14x55 mm (or as per design requirement ), mechanically coated with 25 micron Zn-Sn alloy or hot dipped zinc coated with min 40 micron hex self-drilling fasteners with EPDM washer of approved make confirms to AS3566:2002 class 3.Colour Coated Galvalume/zincalume sheets for roofing. | A4 | 500 | Sqm |
|---|
| 5 | 5 | R2-CS-RW-25 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. (1.50 mm thick coloured F.R.P. corrugated sheet) | A5 | 100 | Sqm |
|---|
| 6 | 6 | R2-CS-RW-13 Galvanised iron sheet 1 mm (20 B.W.G.) eaves precoated gutter 200 mm to 230 mm wide and 100 mm to 125 mm deep moulded or half round girth upto 600mm including iron rods, on the edges (throughout the length) and galvanised iron sheet ferrules with fixtures, for outlets wherever required clamped using W.I. clamp 38 mm x 3 mm fixed 1.0 m C/C including making necessary connections with rain water pipes etc complete and as directed. | A6 | 50 | Rmt |
|---|
| 7 | 7 | R2-CS-SS-06-c Providing and fixing the Mechanical Anchor Fasteners as specified below of Hilti Make or equivalent confirming to IS 1367 (Part 3) at required locations and level including drilling the hole, cleaning and anchoring the bolt as per manufacturers specifications etc. complete as directed by Engineer In Charge. | A7 | 50 | Nos |
|---|
| 8 | 8 | R2-CS-RW-16-b Providing and fixing UV resistant selffit UPVC pipes of approved make for Rainwater downtakes confirming to IS 13592:1992 Type A suitablefor 4kg/sqcm pressure for following pipe diameters including rain water receiving recess with pvc plug bend necessary fittings such as offsets shoes, fixing the pipes on wall with clips filling the joints with solvent/cement and necessary scafolding etc. complete as directed by Engineer In Charge.100mm dia | A8 | 50 | Rmt |
|---|
| 9 | 9 | R2-CS-DD-14 Dismantling steel work in built up sections in angles, tees, flats and channels of rolling shutters, grills, gates, fencing, hoardings, including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within RCF Premises as directed. | A9 | 1000 | Kg |
|---|
| 10 | 10 | CES-200410004 Providing & Fixing FRP MOULDED GRATING WITHOUT CHEQUERED PLATE. \n 1. SIZE: As per Site \n2. HEIGHT: 38MM \n 3. MESH SIZE: 38 X 38 MM \n4. RIB THICKNESS: 7 MM \n5. LOAD CAPACITY: 800 KG/ SQ. METER UDL (MIN.) AT MIN. SUPPORT SPAN OF 910 MM WITH MAXIMUM DEFLECTION OF 1% SPAN. \n6. RESIN TYPE: VINYL ESTER. \n7. COLOUR: YELLOW \n8. CLAMPS: M-TYPE 4 NOS.SS 304 CLAMPS WITH HARDWARE PER PIECE \n9. FOLLOWING TEST REPORT FROM EITHER MANUFACTURER OR NABL ACCREDITED LAB SHALL BE FURNISHED ALONG WITH SUPPLY. \n • FLAME SPREAD RATING SHALL BE CLASS – 1, LESS THAN 25 CONFORMING TO ASTM E-84\n • MTC, LOAD TEST CERTIFICATE. | A10 | 30 | Sqm |
|---|
| 11 | 11 | Supply of Unskilled Labours for Misc works | A11 | 10 | Nos |
|---|
| 12 | 12 | Supply of Semi Skilled Labours for Misc works | A12 | 10 | Nos |
|---|
